Search Documents

By James Paone

The Bureau of Mines made drillability studies with impregnated diamond bits in the laboratory on 7 rock types and in the field on 21 different rock types. Results indicate that drill parameters of rotational speed, thrust, and torque must produce sufficient applied forces to induce stress levels that cause continuous failure in rock to achieve efficient penetration rates. Higher rotational speeds appear to be more effective in drilling relatively harder rocks, although the increased speed causes more bit wear; increases in thrust result in higher drilling rates but not linearly; and up to a critical value a linear relation exists between torque and penetration rate for a specific rock type. Penetration rates with impregnated bits show a trend similar to that obtained with surface-set bits for rock under 25,000 psi compressive strength.

Jan 1, 1966

By J. E. Shelton

Flotation tests are described on samples of two lowgrade nickeliferous ores of Oregon and Washington. The sample from the Congress mine, Ferry County, Wash., contained 1.2 percent Ni, occurring chiefly as millerite. The sample from the Shamrock mine, Jackson County, Oreg., contained 2.20 percent Ni and 0.78 percent Cu occurring chiefly as pentlandite, nickeliferous pyrrhotite, and chalcopyrite. The millerite in the Congress ore was concentrated by flotatioin with aulfydric collectors in a series of locked tests to recover 73 percent of the nickel as a 7 percent bulk concentrate. By successively regrinding and floating the bulk concentrate, it was further concentrated to 12.4 percent Ni at a recovery of 59 percent and 21.8 percent Ni at a recovery of 50 percent. Attempts at selective concentration of the copper-nickel Shamrock ore were only partly successful because of the intimate association of pentlandite and chalcopyrite. The nickel concentrate, which contained 86 percent of the nickel, had an analysis of 4.42 percent Ni and 1.03 percent Cu. The copper concentrate had an analysis of 18.8 percent Cu and 1.96 percent Ni and contained 48.5 percent of the copper. A bulk sulfide concentrate contained 92 percent of the copper and 01 per¬cent of the nickel and had an analysis of 4.17 percent Ni and 1.63 percent Cu.

Jan 1, 1956

By M. H. Kline

The Chestatee mine is one of several well known pyrite deposits in Georgia that are reputed to carry appreciable quantities of copper with the ore. The deposit is? in Lumpkin County on the Chestatee River, 6 miles northeast of Dahlonega (fig. 1). Old records and reports indicated the probable existence of an extensive unmined ore body, but the mine is inaccessible at present. The Bureau of Mines, after studying old maps and records, decided to cor8-drill along the strike of the lense beyond the limits of the indicated old workings in an attempt to extend the possible reserves. The advantageous location of the property indicates that it could become an economic source of pyrite to be used for the manufacture of sulfuric acid. Iron sinter resulting from the roasting of the ores could be sold at a premium in the Birmingham, Ala., area, and the copper content could be extracted to help replace the nation's depleted resources of this metal.

Jan 1, 1949

By Frank D. Lamb, D. A. Woodard

"INTRODUCTION The iron-ore deposits near Cranberry, N. C., were worked as early as 1820, and records show that to date at least 1,500,000 tons of ore has been mined.. The early operators depended on selective mining and hand cobbing to yield a product containing 40 to 50 percent iron. Later, a magnetic concentrator was erected by the Cranberry Furnace Co. and was operated periodically until 1930. The magnetic cobbing method employed yielded satisfactory concentrates, but the plant was shut down because costs were too high. 4/Early in 1944, in connection with the sponge-iron program of the Bureau of Mines, North Carolina and Tennessee were surveyed for the purpose of finding a readily available source of high-grade iron ore for use in the experimental production of sponge iron at Salisbury, N. C., and samples from various sources were tested in the laboratory. The Cranberry ore proved to be best with respect to grade of magnetite concentrates produced, and it was decided that a pilot mill should be built on the Cranberry mine property and that the concentrate made there should be shipped to Salisbury for direct-reduction tests in a commercial brick kiln."

Dec 1, 1946

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-MM-scfd, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 mi 11 ion tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of May 12, 1974, under the terms of the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 and early 1974 indexes . Initial capital investment varies: $45,358,600 for the 4.8-million- ton-per-year (MM tpy) mine in the Eastern province, $54,603,000 for the 6.72 MM tpy mine in the Interior province, and $29,871,000 for the 9.2 MM tpy mine in the Northern Great Plains province. Total capital invest-ments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $61,070,000, $76,753,000, and $56,286,000, respectively. Corresponding selling prices for the coal, per ton, are $4.79, $4.23, and $2.66, assuming a 12-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1974

Improve face ventilation in mines with large cross-sectional entries. Approach Oil shale, salt, and limestone mines typically have large entries. Providing adequate airflow to the working faces of such mines for worker comfort, health, and safety is a substantial ventilation problem. If diesel equipment is used at the face or if a methane hazard exists in the mine, the problem becomes even more complex. To address this problem, a study was conducted under a joint contract between the Oil Shale Committee of the Colorado Mining Association and the Bureau of Mines. The study evaluated two face-ventilation concepts for large-entry mines. Improving Ventilation Two face-ventilation systems were selected for testing of an oil-shale mine, based on results of a cost/benefit analysis. The systems were a free-standing jet fan and a ducted fan operating in the blowing mode. The jet fan was spotted on the intake side in the mouth of the entry being advanced with final positioning, in or out, deter-mined by minimum recirculation. The ducted fan was also positioned in the mouth of the entry being advanced, with its tubing terminating 75 feet from the working face. The mine face entry was a dead heading 55 feet wide, 30 feet high, and 320 feet long. Sulfur hexafluoride (SF.) tracer gas was used to measure the performance of the two systems in diluting mine face pollutants including after-gases from blasting, hot diesel emissions, methane roof layers, and methane emitted from muckpiles.

Jan 1, 1987

By Robert C. Hickman

In its search for strategic minerals, the Bureau of Mines investigated the Rutherford Mine property in Amelia County, Va. The property was visited by F. W. Horton, mining engineer, and Margaret Fuller Boos, mineral technologist, of the Bureau of Mines, in company with Eugene Dawson, of the War Production Board, on July 16-11, 1943. An exploration program by the Bureau was recommended, and work was started on July 28, 1943, and continued until September 16, 1943. A total of 1,250 feet was diamond drilled in 5 holes on the property.

Jan 1, 1950

By F. E. Armstrong

The Bureau of Mines has conducted a research program to systematize the art of locating uncharted and lost oil and gas wells that penetrate coal seams; this publication presents a preliminary summary of its findings. Although no method or combination of methods will guarantee finding all uncharted and abandoned wells in a particular area, at least 75 percent of such wells can be located by compiling and applying all available information and using modern metal detectors.

Jan 1, 1973

By Harold W. Lipper

A NEW record was set for helium shipment in 1962 for the 13th successive year. For the first time since 1949, the production of helium from natural gas at Bureau of Mines plants was less than in the previous year. The Bureau shipped 599.5 million cubic feet, 9 percent more than the 1961 volume, and produced 680.9 million cubic feet-a decrease of 6 percent from the record set in 1961. The Bureau added 77.2 million cubic feet to the volume stored for future use. Of the total 524.6 million cubic feet in storage, 522.4 million cubic feet is accumulated excess production from Bureau of Mines plants. The remaining 2.2 million cubic feet was purchased during 1962 from industry under the helium conservation program. The first two of five private plants began production in December to recover helium for conservation storage and ultimate use. A 425-mile pipeline system to transport helium from the five private plants to the Cliffside field was constructed by the Bureau at a cost of about $8 million.

Jan 1, 1963

By A. J. Kraemer

"Introduction In 1925 the Bureau of Mines published as Technical Paper 346 a discussion of typical crude oils of the Western Hemisphere. That paper was one of a series of surveys of typical crude oils, and was the first of these to deal with properties of crude oils from countries other than the United States. The paper contains comments, tabulated data, and individual analyses of crudes typical of the producing districts of Canada, Mexico, Trinidad, Venezuela, Argentina, Colombia, and Peru; for comparison, it also has analyses of typical crudes from the chief producing districts of the United States.The Bureau of Mines undertook a study of foreign crude oils for two reasons: First, foreign fields are potential sources of supply for the United States; in fact, considerable quantities of some foreign crudes have already been imported. Second, these oils are very similar in physical and chemical properties to oils found in the United States, and a study of these resemblances has scientific value.After the publication of Technical Paper 346, the attention of the Bureau was called to the fact that the two analyses of crude oil from Venezuela which appeared in that paper were not completely representative of the production of that country. Samples of other types of oil were procured through the cooperation of Mr. R. Ogarrio, manager of the Texas Petroleum. Co., Huston, Texas, and officials of the following companies operating in Venezuela; British Controlled Oilfields, Ltd., Venezuelan Oil Concessions, Ltd., Creole Syndicate, and Venezuelan Gulf Oil Co.. Samples were collected and dispatched by Mr. D. 3. Park, representative in Maracaibo, Venezuela, of the Texas Petroleum Co. The value of the interest and cooperation of these agencies in obtaining the samples is gratefully acknowledged."

May 1, 1927

By Floyd D. Everett

The J. B. fluorite deposit is in the Washington mining district, southwestern Beaver County, Utah (fig. 1). Fluorite outcrops were found during 1942, and three lode claims wore located. Little work was done on the property until October 1943, at which time the Bureau of Mines started development to determine the subsurface extent of the fluorite mineralization exposed at the surface. The most prominent rocks in the J. B. mine area are porphyries, which vary considerably in composition. Dacite porphyry appears to be the most common host rock for the fluorite-quartz-calcite lenticular masses. The dacite porphyry in the area is highly brecciated over a strike length of more than 1 mile. Fluorite deposits in the brecciated zone cover a strike length of approximately 400 foot. The fluorite lenses range in length from 40 to 200 feet and in width from 4 to 10 feet (fig. 2). The Bureau of Mines work on the J. B. property was started in October 1943 and completed in October a year later. The work consisted of surface trenching by bulldozer and hand methods, shaft sinking, drifting, and crosscutting. Eleven trenches totaling 1,800 linear feet were excavated. An inclined shaft was sunk to a depth of 105 feet, and from thin shaft 577 feet of drifts and crosscuts were driven to outline the extent of the mineral deposit (fig. 3). Two hundred ninety-seven samples were taken in the surface trenches and underground workings. The locations of the samples and analyses arc shown in accompanying figures and tables. Results of metallurgical tests comprise the concluding section of this report.

Jan 1, 1950

By Richard A. Allwes

The Bureau of Mines conducted an in-mine case study on two consecutive three-entry gate road systems designed in accordance with the stiff-yield pillar design concept. This Bureau study was conducted in order to further develop technology that will improve the health and safety aspects of longwall mining. Support loading and strata activity were monitored to determine the effects of retreat longwall mining on the gate road ground control system. Analyses of pillar stress and roof bolt loading histories revealed that headgate roof support elements ex-perienced cumulative loading throughout the life of the longwall panel. Tailgate pillar loadings had significantly different histories from the loading histories of the headgate pillars. Stress relief occurred in the tailgate pillars following the passage of the longwall face. More-over, the stiff-yield pillar design, with the abutment pillar placed adjacent to the working panel when part of the headgate system, provided effective ground control in that no major roof falls or roof problems were experienced in the headgate or tailgate systems during longwall mining.

Jan 1, 1985

By T. J. Ballard

The Conrad Hill mine vas first opened as a gold mine about 182 and has been operated at various times since then. The Bureau of Mines, as part of the strategic minerals program, mapped and sampled the accessible mine workings. The work failed to reveal appreciable copper values or evidence of additional ore deposits.

Jan 1, 1948

By E. E. Maillot

In 1943, diamond drilling by the Bureau of Mines, comprising 11 holes which totaled 1,295.6 feet, showed that the pegmatite at Black Mountain consisted of shallow lenses in interbedded biotite-quartz-schist and impure quartzite. The average thickness of the pegmatite was 9.7 feet. Mineralization had a zonal arrangement. Beryl was most abundant near the footwall contact of the pegmatite. The average estimated beryl content of the pegmatite exposed at the surface was 0.81 percent, and the highest content of any pegmatite area was 1.75 percent. Other economic minerals were scrap mica, feldspar, spodumene, and lepidolite. Representative samples of the Black Mountain deposit failed to yield high-grade boryl concentrates by straight flotation owing to the presence of considerable spodumene. By employing heavy medium separation to remove the spodumene, 75.4 percent of the. BeO wan recovered in a flotation concentrate assaying 10.4 percent BeO.

Jan 1, 1949

By M. Howard Berliner

During the spring of 1944, the Bureau of Mines investigated the Crescent mine area near the village of Rewey, Iowa County, Wis., as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the Nation's war program. The Bureau of Mines completed 24 churn-drill holes in an area immediately to the west of a mineralized section which had been mined through shallow workings for lead and zinc more than 40 years earlier.

Jan 1, 1948

By W. W. Adams

"During the calendar year 1925 the Bureau of Mines received from the operators of several hundred mines and quarries complete accident records covering deaths, permanent disabilities, and “lost time” temporary injuries. Some of the companies, - those that participated in the National Safety Competition-also furnished information showing the number of man-hours of work performed during the year. With these two types of information it was possible to calculate the accident-frequency and accident-severity rates of the different plants. Complete and comparable reports of accidents and Man-hours of “exposure” were received from 34 underground metal mines, 59 underground coal mines, 15 underground mines producing other nonmetallic minerals, and 102 open quarries or open-pit mines. The figures in the table appended to this report show the accident severity rates and other data for each of the 34 underground metal mines and for the group as a whole. It is proposed to publish similar figures for the other classes of mines and quarries at an early date.The 34 metal mines listed in the table are situated in Arizona, Idaho, Kansas, Michigan, Minnesota, Missouri, New Jersey, New Mexico, Oklahoma, South Dakota., and Utah; they employed 5, 925 men, an average of 174 men per mine, including employees above-ground as well as underground. With but few exceptions, 50 men was the minimum number of employees in any mine. The total period of employment or “exposure” at the 34 mines was 14,612,607 man-hours, an average of 2,466 hours per man, or the equivalent of 308 work-days of eight hours for each employee. Accidents resulted in 15 fatalities, 9 permanent disabilities, and 1,950 temporary “lost time” injuries (causing disability exceeding remainder of shift). The fatal and nonfatal injuries represented 132,575 days of disability. Thus the accident frequency rate for the group was 135 accidents per million hours and the accident severity rate was 9.073 days lost per thousand hours of 1 “exposure”. The severity rates ranged from 0.227 to 88.653, while the ·range of the accident-frequency rates was from 16. 6 to 307 .4. In compiling the accident severity rates shown in the table, all accidents caused by explosives were weighted at twice the number of days actually lost, as one of the purposes of the National Safety Competition was to stress the prevention of accidents caused by explosives."

Sep 1, 1926

By John D. Bardill

This report covers magnetic surveys in the Dannemora arca , which was part of a general survey of magnetite deposits in New York started in 1943 . The objective of these surveys was to afford a basis for the selection of exploration projects .

Jan 1, 1947

By C. B. Manula, R. L. Sanford, R. A. Rivell

A - Contains the coordinate pair information for deriving the co¬efficients of the 3rd degree polynomial which approximates the loading station equation. C(N) - Coefficients for third degree approximating polynomial. I - General DO LOOP variable. K - Position in BRANCH of next character. L - Format specification in DEFINE FILE statement. X - Uniform displacement for random uniform number. Y - Load increment At. AO-A3 - Coefficients of approximating polynomial for loading station equation. GR - Grade direction, or grade resistance. IQ - Counts quadruples of distance grade speed and end of route for determining total distance. IT - Intersection counter in XXXDEF. Il - Station number trip is leaving. Jl - Station number for trip destination. J2-J8 - Motor assignments and functions for given trip. KK - Location of starting grade and distance in DISTGR KK - Position of decimal point in real number. KZ - DO LOOP variable for motor assignment check. LL - Location of ending grade and distance in DISTGR. Ll - Position in IECB of station satisfied. L3 - Next available position for IECB sort. MM - Flag for printing the failure of sanding to overcome slippage. NN - Trip destination in MOTSER RR - Rolling Resistance. XK - Station level or type.

Jan 1, 1974

By B. W. Gandrud

[The meaning of the term "bauxite' has always been somewhat vague and indefinite, and the term has been used in various applications to denote sometimes a rock, sometimes a mineral, but more frequently an ore. It seems logical to think of bauxite as an ore, however, because a very large part (probably at least 85 per cent) of the entire world's production of bauxite is at present being used as a source of aluminum and aluminum chemicals. In the United States there are two districts that, produce bauxite - the Arkansas district and the Alabama-Georgia-Tennessee-Mississippi district. The deposits in Mississippi have been discovered recently and are riot as yet productive but it seems reasonable to consider them as apart of the-district hat includes the deposits of Alabama, Georgia, and Tennessee. The, two districts are often referred to as the Arkansas field and the Appalachian field. Of these two the Arkansas field has been by far the largest producer, and at present over 90 per cent of the bauxite production of they United States comes from the Arkansas field. The bauxite industry in the Appalachian field had its beginning in 1889, and since that time the total production of the states of Alabama, Georgia, and Tennessee has been, nearly a million tons. The production of bauxite in this field has languished in the last five, or six, years, and In 1927 its production was only about 14,000 tons, according to Harder4. The recent decrease in production is due mainly to the fact that many .of the known deposits of commercial-grade ore have become exhausted. There are, however, considerable quantities of low-grade bauxite in the Appalachian field, but these have not been available because there has been no satisfactory way of concentrating low-grade bauxite. The quantity, of low-grade material in the Appalachian field is probably, fully as large as the tonnage of commercial ore which the field has already produced.]

Jan 1, 1928

By Wilbur I. Duvall

This paper presents arguments which show that a velocity seismograph should be used to measure building and ground vibrations produced by blasting . However , portable velocity seismographs suitable for this type of measurement are not commercially available . The paper describes how a velocity seismograph can be assembled from commercially available velocity gages , amplifiers , and recorders . Also , specifications are given which could be used in the design and manufacture of a portable velocity seismograph suitable for measuring vibrations from blasting .

Jan 1, 1964