Search Documents

By R. V. Ramani, A. S. C. Owili-eger

Mathematical modeling is a scientific exercise with the objective of developing simplified mathematical statements that relate to one another the same way as the processes that are being modeled. The utility value of the model is dependent on the ability of the model to closely approximate prototype behavior. Development of a perfect model, therefore, is an unrealistic objective because of the simpli¬fying assumptions made in building it. However, for a model to be acceptable for application, its operating characteristics or data generated from it should, within reasonable accuracy, duplicate proto¬performance. The validity and accuracy of a model depends on the mathematical constraints presupposed in model formulation. The final model must be tested for mathematical validity and for closeness of representation of the prototype. Mathematical validity, does not, however, imply that the model is accurate and correct but is prerequisite. Model testing and verification for the steady state model are given in Owili-Eger et al (1973). The unsteady state model has been tested for mathematical validity and found to be correct but has not yet been applied to a field condition for lack of data. However, in the application discussed below, the unsteady state model results are compared with pressure curves reported in literature and also with results from the steady state model. Coal seam characteristics and gas reservoir pressure used in this application are extracted from Kissell (1972). These characteristics are for the Pittsburgh seam, Federal No. 2 Mine, Fairview, West Virginia.

Jan 1, 1974

A working understanding of present coal mine communications equipment and its usage is an essential prerequisite to the determination of future communications systems needs. As a means of gaining this understanding, a field survey program was planned and implemented. The plan formulated called for obtaining both qualitative and quantitative data from three main areas of interest: the types, physical condition, and performance characteristics of equipment presently used in the sample of mines to be visited; the relationship present communications has to safety and productivity; and the practical, future communications needs as de- rived through interviews with present mine management. In compliance with the original plan, the type and physical condition of equipment in use was found through at-mine interviews of personnel responsible for installation and maintenance. Further evaluation was made through the review of equipment instruction books and maintenance manuals and through in-mine inspection of communications equipment and signal distribution networks. The performance characteristics were determined through listening to conversations and noise levels and by talk-testing from randomly selected stations throughout each mine. System operation was evaluated by asking communication system users their opinions and by noting any difficulties personnel had using the systems. Plans in the second area of interest--that of relating communications to mining operations-- were to observe mining operations and usage of communications; to gain insight through interviews with mine management, from mine superintendents to section foreman; and to look for correlation between communications, production, and safety. Lastly the communication systems needs and requirements were determined from first hand interviews of mine personnel, from the analysis that lead to the individual reports on the eight mines, and from an overview of all of the mines studied. The latter was done to find commonality between the needs of the individual mines such that system requirements having the greatest universal value could be derived, thus lowering per-mine cost of equipment through economics of scale. Armed with tape recorders, backgrounds in communications technology, and with an interview questionnaire that was improved as experience was gained, engineers visited the eight mines to obtain the raw data from which the needs and requirements could be developed through analysis. During the first part of the program two days were spent at each mine so that interviews and tours could be completed, and so that full eight hour shift phone usage recordings could be obtained for statistical analysis. One day visits were sufficient for those trips where tape recordings were not made. During the later trips less attention was given to the statistical nature of communications, and more to how communications relates to the total mining operation.

Nov 15, 1974

By Wilbur I. Duvall

In a previous report, entitled A Gage and Recording Equipment for Measuring Dynamic Strain in Rock, a control circuit for a drum camera was described. The purpose of this control circuit was to provide a means for firing seismic caps, synchronizing the firing of the cap with the opening of the camera shutters and generating an electrical impulse at the instant of detonation. The operation of this circuit depended on the following two characteristics of seismic caps: (1) these caps contain a bridge, which breaks at the instant of detonation, and, the firing delay time of the cap is a function of the firing current. During the course of the Bureau's studies, considerable difficulty was experienced from "firing hash", i.e., spurious vibrations that appeared on the records at the time of detonation. The cause of most of this "firing hash" was traced to the intermittent grounding of the cap leads at the time of detonation. As the cap leads were still connected to the firing battery, the grounding of the leads permitted current to flow through the rock to the gage and to return to the firing battery through the shield on the gage cables. The intermittent flow of current along the cable shield produced potentials on the gage leads that were recorded as the "firing hash." To eliminate this difficulty, it is necessary to remove the firing voltage from the cap leads the instant the cap detonates. This report supplements the previous report and describes an improved circuit that can be used to fire seismic caps, remove the firing voltage from the cap leads the instant the cap fires, control the firing delay time in the cap, and generate reference signals at the time current starts flowing in the cap circuit and at the time the cap detonates. These reference signals can be used to determine the firing delay time of seismic caps and the time at which the seismic wave is generated by the explosion.

Jan 1, 1950

By Dara Stock, Fred Turin, Kim Cornelius, Lisa Steiner

Growing concern from labor unions, regulatory agencies, and industry about the safety of a prevalent underground coal mining method which utilizes remote control has prompted human factors field evaluation of mining activities. Remote control operations were implemented with little consideration given to human-system interactions. Ideally, collecting and analyzing information prior to implementing new technology would have helped to address potential problems. One such problem that operators and other mine personnel are faced with is the question of where they should safely position themselves to avoid injury while remotely operating machinery. To determine work methods employed by machine operators before and after implementation of the new method, work sampling techniques have been used to provide data about positioning of face crew members at different points in the mining cycle. This data provides information for optimal positioning, leading to safer operating procedures and identifying training shortfalls.

By W. H. Young

THE BITUMINOUS coal and lignite industry declined slightly in 1961, compared with the 1960 figures. All of the major items, production, consumption, average value, exports, and employment, declined. Even the steady upward trend in mechanization failed to materialize; the percentages of total tonnages mechanically loaded and cleaned remained the same as in the preceding year. However, tonnage per man per day increased from 12.83 tons in 1960 to 13.87 tons in 1961, owing partly to the increased tonnage produced by continuous mining machines. Also, the percentage of total production mined by stripping and by augers increased slightly. Production.-The output of bituminous coal and lignite in the United States in 1961-403 million tons-was 3 percent less than the 416 million tons produced in 1960. Production was retarded in 1961, owing largely to the business recession and reduced exports.

Jan 1, 1962

During 1990-1999, a total of 458 fires occurred in all coal mining categories; 157 of those fires caused 164 injuries and 2 fatalities. The greatest number of fues and fire injuries occurred at surface mines, whch also had the highest risk rate values. A total of 66 fuefighting interventions were required. Of these, there were 25 mine rescue team interventions in underground mines, including 5 mobile equipment firefighting interventions, and 41 fire brigade and fire department interventions at all surface operations, including 19 mobile equipment interventions. In all, 50 fires destroyed or heavily damaged equipment (including 16 pieces of mobile equipment) because of failure of other firefighting methods, late fire detection, undetected fires, or fire size. A total of 1 14 fires were detected late by smoke, and 42 fires were not detected.

By Thomas M. Barczak

Purchasing a new set of longwall shields requires a substantial investment. A poor shield design can lead to economic hardships, safety concerns for the mine workers, and closure of the mine. This paper addresses several key points that should be considered in the procurement process: (1) understanding your goals and the logic in selecting a higher capacity shield, (2) the importance of completing performance testing before production shield fabrication begins, (3) making sure performance testing is properly done, (4) measuring load(stress) development during performance testing, (5) testing a shield to failure, and (6) the value of buying extra shields. In addition, several challenges are proposed for consideration in future shield designs. These include (1) 100,000 life-cycle expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control by optimizing setting pressures, (4) lubricated link joint design concepts, (5) composite material applications to reduce shield weight, (6) incorporating periodic weighting predictive algorithms into the data-processing software, (7) advanced component load measurement on two to three specially instrumented shields to detect loading in the structural components, and (8) constant set leg cylinder design.

Jan 10, 2000

By John Ward Smith

The Bureau of Mines derived equations expressing the theoretical relationship between density of oil-shale rock and its organic content. Effects on theoretical shale density produced by variations in mineral composition and organic matter properties were evaluated. The theoretical relationship was extended to relate oil-shale density to oil yield in both oil weight and volume units by considering the fraction of organic matter converted to oil and the specific gravity of the oil produced. Corollary equations relating organic content by volume to organic content by weight and to oil yield were developed. The general relationships apply to an oil-shale deposit uniform in character. Application of the theoretical relationships to Green River Formation oil shales was demonstrated.

Jan 1, 1969

To facilitate compliance with title 30 CFR 75.1001-1(b), which requires testing and calibrating of trolley line automatic circuit interrupting devices at intervals not to exceed six months. Approach Calibration of a circuit breaker ideally implies the passage of the expected fault current through the sensing circuit, and observing a successful circuit interruption at the preset level within a specified time. On trolley lines, the required current may be a few thousand amperes, with maximum duration well exceeding one-tenth of a second. Any method of obtaining this calibration current Involving the trolley wire can contribute to wire sagging and other permanent damage to the haul-age system due to the high energy dissipated during the test. Also, control to assure that exactly the required level and duration of current flow is obtained implies the use of equipment which is simply not available In the ordinary mine. Under a Bureau of Mines contract, a circuit to achieve the necessary calibration pulse was conceived and built. How It Works Two prototype units were fabricated and have been field tested by MSHA technical support engineers in under-ground mines. The equipment consists of an electronics Package 20 x 24 x 8 inches and weighing 93 pounds, including a side-mounted circuit breaker, with a set of 8 foot long detachable, AWG #4/0 leads with plier-type clamps. The total lead assembly weighs 21 pounds.

Jan 1, 1981

By Robert W. Freedman, Robert L. Craft, William G. Humphrey

As part of a continuing effort to reduce the weight and bulk of equipment that mining personnel must carry underground, the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) investigated accurate and convenient gas samplers for use by mine inspectors in sampling mine atmospheres. The samplers are septum-stoppered glass vials commonly used for routine blood sampling. These lightweight, compact samplers yield results comparable with those obtained with conventional bottle samplers of 250-ml nominal capacity.

Jan 1, 1975

By B. G. White

NIOSH researchers have identified a pattern of fracture zone development that suggests an explanation for fracture formation around rectangular openings in underground mines. This pattern is characterized by shearing and dilation that result in either faults or in the repeated formation and propagation of en echelon fractures from sites of tension. Two computer modeling codes, Fast Lagrangian Analysis of Continua (FLAC) and Particle Flow Code (PFC), were used to model different aspects of this pattern. Use of very small elements with FLAC enabled the identification of sites of initial tension near the skin of square-cornered rectangular openings, while PFC allowed the initiation and progressive development of fractures from these sites to be followed as the fractures evolved. Such studies can lead to a greater understanding of how roof support can be better selected and installed for specific conditions in underground mines prone to roof falls and rock bursts. These studies may also lead to modifications of corner and opening shapes that could be incorporated into mine designs to produce more stable mine openings and reduce the risks of rock falls and rock bursts.

Viable domestic mineral industries are essential to the economic health of the United States and the well-being of its citizens. The charts in this publication reflect developments significant to the Nation's mineral industries during 1975. Last year was a year of reduced activity for the Nation's mineral industries. Although the value of the country's total mineral output rose, for example, the overall production and use of many minerals fell. At the same time, the industry experienced lower profits and higher debt/equity ratios. These and other adverse effects on many segments of the Nation's mineral industries resulted from the overall decline in domestic and international economic activity.

Jan 1, 1976

Reduce the dust levels to which jacksetters and helpers on auger mining sections are exposed by identifying viable, effective methods for control-ling respirable dust on these sections. Approach The Bureau of Mines con-ducted laboratory tests and respirable dust surveys to identify the factors that distinguish clean auger mining operations from dusty ones. Study Results Results of the Bureau's study revealed that ventilation is the most important element of auger mining dust control. The four must important venitilation parameters are airflow, curtain configuration, curtain setback, and curtain installation.

Jan 1, 1988

This report, which updates and supersedes the Office of Surface Mining's 10-year progress report published in 1987, deals with the accomplishments of the regulatory and abandoned mine land reclamation programs during the first 15 years of the Surface Mining Control and Reclamation Act of 1977 (SMCRA). Part 1 is an illustrated description of on-the-ground accomplishments; Part 2 presents statistical information for the 15-year period. The data in this statistical report are organized in two sections: national statistics and state statistics. The national statistics provide an overview of coal mining and the implementation of SMCRA since 1977. The information reported for the states presents a brief description of the coal reserves in each area, accompanied by detailed statistics and graphs that relate each state to the nation as a whole. The statistics compiled in this report are from the Office of Surface Mining's files, computer data systems, and annual reports. During the early years of the program, many of the data categories were evolving and changing; therefore, data reported over the 15-year period are not complete for all states for all years, and where data was unavailable or zero, a dash (-) is shown for that item. The data sources used to compile the tables and graphs are listed and described in detail on page 76. Due to the number of requests for this information in the past, statistical information about coal mining and its regulation will be available each year as an appendix to the Office of Surface Mining's Annual Report to Congress. Beginning in Fiscal Year 1993, this information will be compiled and published on an annual basis. For more information about this report, call or write the: Public Affairs Office Office of Surface Mining 1951 Constitution Ave., N. W. Washington, D.C. 20240 (202) 208-2553

Jan 1, 1992

By Charles L. Kimbell

In overview, the world's mineral industry in 1989 registered gains over its 1988 performance, but these gains were by no means as pronounced as had been those of 1988. The traditional statistical measures of mineral industry performance, namely production, trade, and consumption levels, reflected significant growth in most industry sectors from crude material extraction through the gamut of down- stream processing. Growth in market economy countries generally exceeded growth in the centrally planned economy countries as a result of a variety of causes that will be covered subsequently, but even among the centrally planned countries there were some upturns. In contrast to these measures of the soundness of the industry, the situation for nonfuel mineral and metal prices was less satisfactory than in 1988, and low crude oil prices continued as a problem for the all-important petroleum sector, despite some gains during the year. The oil price situation mitigated against price increases for competitive fuels. Although this was unfavorable for fuel producers, it remained advantageous to consumers, including nonfuel mineral producers, processors, and transporters. Thus it cannot be viewed as a negative factor for the whole of the global mineral industry. Global crude mineral output value was estimated at nearly $1,420 billion in current dollars, an increase of 9% over the 1988 level, and an increase in current dollar terms for the seventh consecutive year. Measured in terms of constant dollars, however, adjusting for inflation, the increase was only 4.7% compared with the 1988 level. Despite the prolonged growth trend, the 1989 crude mineral output value level was still 3.2% below the record high set in 1980, which was $1,467 billion in terms of 1989 dollars.

Jan 1, 1992

By Graham W. Marks, RALPH MILLS, FRANK COSSEY

To determine the focal length of lenses or the performance of lens systems before mounting them permanently , it is desirable to have a device in which one or more lenses can be mounted easily and their positions relative to a light source and screen changed readily . We have designed and constructed such an optical bench and lens holder . The bench is similar to that of Houstoun5/ but has been modified , whereas the lens holder is , we believe , a new design .

Jan 1, 1948

Provide longwall operators with an alternative strategy for placement of gob gas ventholes to improve gas production.

Jan 1, 1995

By Charles L. Kimbell

Tables 16 through 19 continue the series of providing the world merchant fleet distribution by type of vessel and the ranking of the major fleets by country of registry. Table 20 this year provides a summary of the world's liquid gas carrier fleet. These vessels are included in the totals given for the world's tanker fleet, but gives a breakdown demonstrating the growth of the importance of natural gas in the world's energy commodity consumption. Panama and Suez Canals Tables 21 and 22 provide the latest available information on the transit of mineral commodities through the Panama Canal, by number of vessels, direction, and the commodities transported. Although the number of vessels transiting the Panama Canal dropped slightly (0.5%) between 1989 and 1990, the total amount of cargo moved rose by 3.6% and the amount of mineral commodities moved rose by 7.2%.

Jan 1, 1993

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977

Develop design and support guidelines for coal mine entry intersections based upon results of integrated field and numerical modeling analyses of structural parameters for improving ground stability. Background Underground coal mines contain a large number of entry intersections. Dome-shaped zones over the intersections are unstable and are often associated with roof falls. These roof falls may occur during mine development, trapping equipment and endangering miners. These high-risk areas of the mine account for 10 pct of the total number of ground-failure-caused fatalities. The falls, ranging from heights of 1 to 20 ft, cause high dilution and slow the advance rates. Stability at intersections is influenced by four structurally interrelated parameters: in situ stress, geological discontinuities and physical properties, intersection geometry, and roof span. Because of the complex interaction of these parameters, the actual mechanism of roof failure may vary considerably, depending upon the roof lithology, rock strength, and stress conditions.

Jan 1, 1990