Search Documents

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields, with rapid depletion of existing reserves, emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry for meeting increasing market demands; but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields. Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most current operations are of the pressure-maintenance type, in which the reservoir pressure is maintained or partly maintained by injecting natural gas to in-crease oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes current gas-and water-injection projects in California.

Jan 1, 1952

By R. B. Prater

The Bureau of Mines conducted research to separate the F from byproduct Zn concentrates obtained from fluorspar (CaF2) production, as part of the Bureau's effort to devise efficient, environmentally acceptable technology for recovering Zn from resources considered undesirable by Zn producers. Sulfuric acid (H2SO4) was found to be effective in F removal, while ammonium carbonate [(NH4)2C031 was not. The most important variables for reducing the necessary residence time were found to be temperature and agitation. Optimum leaching conditions were 75° C and 500 r/min for 2 h at 40 pct solids with 0.2 g acid per gram of concentrate, which resulted in a 98.3-pct F extraction. Zinc losses during F removal were in the range of 2 to 3.3 pct. Other elements such as Fe, Cd, Ca, and Cu were also partially dissolved. About 93 pct of the F was removed from the leach solution by neutralization and precipitation with calcium hydroxide [Ca(OH)2]. Additional treatment might be necessary to limit the buildup of soluble elements in the recycled leach solution.

Jan 1, 1985

By James W. Townsend

[The Harrington-Hickory mine in the Star raining district, Beaver County, Utah, has produced approximately 20,000 tons of lead-zinc-silver ores since 1910. Production previous to 1910 is not known. The mine is owned by the New Majestic Mining Co. The property was rehabilitated and operated by James D. Williams under a 10-year lease with option to purchase from April 1943 to May 1949, Loans from the Reconstruction Finance Corporation in the aggregate of $41,000 wore used in construction of an access road, rehabilitation of the mine, and purchase of equipment for full-scale operation. The improved, all-weather access road extends from loading ramps on the Union Pacific Railroad at Milord to the urine storage bins 5 miles west o f town. The mine is serviced electrically by a. 5,000-volt line owned by Telluride Power Co. Mine transformers step the voltage down to 440/220/110 for surface and underground service.]

Jan 1, 1953

By C. B. Manula

This report is mainly concerned with the modification and development of a users manual for the Open-Pit Materials Handling Simulator (OPMHS) developed at Penn State. Model Modifications included the introduction of a free-format input, the application of a Weibull random generator, facilities to stochastically simulate shovel-dragline operations, and routines to increase the flexibility in making truck assignments. At the same time, core storage requirements and execution times were minimized and all P.S.U. conventions were removed to allow operation on other computing systems.

Jan 1, 1976

By L. J. Defferding

This report documents the work performed by Battelle-Northwest and its sub-contractors in Phase I of a project to develop a cross pit conveyor system for the Bureau of Mines. The conveyor system description includes details of the conceptual design as well as system and component specifications. The selection of primary and back-up sites for system demonstration is discussed. Maneuvers and operating sequences required for mining the selected demonstration site are described and illustrated in detail. Economic viability of the cross pit conveyor system was analyzed by estimating the cost of overburden removal per ton of coal using the Battelle-designed concept and comparing these costs to the cost of an available state-of-the-art 30-yd3 dragline operation. Testing and trade-off studies conducted are documented and the results presented. Alternate designs considered in developing the selected cross pit concept are included for completeness. Based on the evaluation of the selected concept, it was concluded that the cross pit conveyor system proposed by Battelle is a technically and economically feasible overburden handling method with a good potential to improve western coal mining efficiency.

Jan 1, 1976

By R. A. Cortese

The U.S. Bureau of Mines has developed a flame-radiation-powered trigger device to explosively activate suppression barriers to quench gas and coal dust explosions. The major component of the device is a silicon solar panel, which converts radiation from the developing explosion into electrical energy to initiate an electric detonator, which releases an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 W of electrical power when exposed to the sunlight are producing about 200 W when exposed to a full-scale dust explosion. The solar panel is electrically isolated from the detonator by a pressure-sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame-powered photogenerator prevents false barrier activation and requires no external power supply.

Jan 1, 2010

By Donald I. Bleiwas

The U.S. Bureau of Mines has evaluated the potential availability of nickel from 36 deposits or districts in 16 market-economy countries (MECs), analyzing more than 95 percent of production in those countries. This study indicates the quantity of nickel available on the basis of net production costs and total costs with a 0-pct and a 10-pct discounted cash flow rate of return (DCFROR). Costs of production are expressed in dollars per pound of recovered nickel. The study also indicates sensitivities of the cost of production to energy, labor, and other factors. The studied deposits and properties contain approximately 33 Mmt of recoverable nickel. About 26 Mmt of nickel is potentially recoverable from laterite deposits, of which 4.5 Mmt can be produced at $2.50/lb or less with a 0-pct DCFROR. Approximately 7 Mmt of nickel is potentially recoverable from sulfide deposits, of which about 6.3 Mint could be produced at $2.50/lb or less at a 0-pct DCFROR. The price of nickel averaged above $6.00/lb in 1988. Sensitivity studies performed for both laterite and sulfide deposits indicate that the total cost of producing nickel from laterites is most sensitive to increases in energy costs and that the total cost of producing nickel from sulfide deposits is most sensitive to increases in labor costs; sulfides are also affected by changes in revenues from byproducts.

Jan 1, 1991

By S. A. Bortz

This report presents the results of an extensive laboratory testing program to determine the physical properties of shotcrete including the use of fast-set agents, controlled set cements, and both wet and dry shotcreting equipment. Shotcrete was placed under simulated field conditions using the dry and wet processes. Mechanical properties obtained for accelerated and nonaccelerated shotcretes include compressive, flexural, and shear strength, elastic modulus and Poisson's ratio, and shear and tensile properties of shotcrete bonded to coal, sandstone, and shale. Physical properties measured were unit weight and permeability to methane gas. The data show that rapid setting shotcrete has the potential for improved coal mine ground control. There is no clear evidence that either wet or dry process shotcrete is superior to the other; however, indications are that regulated set cement is preferred to cement containing fast-setting admixtures.

Jan 1, 1973

By D. R. Tweeton

The U.S. Bureau of Mines, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research Organization, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in locating a brine solution simulating in situ leach solution or a high-conductivity plume of contamination. The brine was approximately 160 m below the surface. The testsite was the University's San Xavier experimental mine near Tucson, AZ. Geo- physical surveys using surface and surface-borehole, time-domain electromagnetic (TEM) induction; surface controlled-source audiofrequency magnetotellurics (CSAMT); surface-borehole, frequency- domain electromagnetic (FEM) induction; crosshole FEM; and surface magnetic field ellipticity were conducted before and during brine injection. The surface TEM data showed a broad decrease in resistivity. CSAMT measurements with the conventional orientation did not detect the brine, but measurements with another orientation indicated some decrease in resistivity. The surface-borehole and crosshole methods located a known fracture and other fracture zones inferred from borehole induction logs. Surface magnetic field ellipticity data showed a broad decrease in resistivity at depth following brine injection.

Jan 1, 2010

By Richard D. Miller

This publication contains routine analyses and related source data for 295 natural gas samples from 18 States collected during calendar year 1963 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863/ and 576.4/

Jan 1, 1965

By Richard D. Miller

This publication contains routine analyses and related source data for 295 natural gas samples from 18 States collected during calendar year 1963 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863/ and 576.4/

Jan 1, 1965

By S. K. R. Iyengar

This report presents the results of a study to develop optimal designs for light-weight mine roof supports for use in underground coal mines. A load capacity of 196 kN (22 tons) and a height adjustable between 1.829 m (72 inches) and 2.438 m (96 inches) were taken as the design parameters and the design goal was a unit weighing less than 22.3 kg (50 lbs). Three alternative design concepts were explored, viz. mechanical, hydraulic, and hydro-mechanical and a total of 13 designs analyzed in detail. Steel, aluminum alloy and composites were the main potential construction materials investigated for suitability from structural, life, and safety and other considerations. The designs considered most promising for development were: (i) the mechanical screw-pin type using telescopic tubes and a fine adjustment screw thread section (ii) the all-hydraulic type, of steel, aluminum alloy or aramid graphite construction (iii) the hydro-mechanical design using telescopic tubes and a short stroke hydraulic cylinder for fine adjustment It is shown that by using realistic mathematical models for stress and deflection calculations, it is possible to reduce prop weight to the design goal. The analysis presented for all-hydraulic props is applicable to hydraulic cylinders on all mining equipment and similar machinery. This report includes the computer program and user's guide for analyzing hydraulic cylinders as well as a cross-indexed bibliography on structural composites.

Jan 1, 1978

By R. Farrar

Protective canopies for conventional electric face equipment, including shuttle cars, operating in low coal (less than 48 inches) were designed, fabricated, installed and evaluated on in-mine machines engaged in regular coal mining operations. This work was performed under contract to the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center. The canopies will support a vertical load of 18,000 pounds and provide protection against both roof falls and contact with the mine rib. Canopy configurations were established based on human engineering studies, full scale canopy mockups, and in-mine observation and consultation with mine and equipment manufacturing personnel. Overall height of each canopy is hydraulically adjustable between a minimum of 32 inches and a maximum of 40 inches. Canopy tops are open framework, welded structures, covered with expanded metal mesh. Structural members are 1 3/4-inch or 2-inch square tubing of AISI 413ON and ASTM A500 material, respectively. The canopy tops are typically supported by an understructure and upright post arrangement that is either integrated into the current operator platform or attached to the machine frame. The four upright corner posts house the hydraulic actuators. Canopy tops are elevated horizontally. Canopies are welded or bolted to the existing machines. Installation is accomplished with a minimal amount of interface modifications. No major machine design changes are required. Canopies were trial installed and load tested at the manufacturer's facility prior to installation on the in-mine machines. Canopies were installed on a Joy 14BU10 Loader, 16RB-3AH Cutter, and two 21SC Shuttle Cars, and a Galis 300 Roof Drill and 460-S Face Drill. Canopy installations were evaluated in the Jewell Ridge Coal Company No. 12 and Big Creek Tiller Mines. Operational time accumulated on the installations during evaluation ranged from 1 week to 14 weeks of two-shift operation. All five canopy designs, manufacture, and test were successfully accomplished. The five canopies met all safety requirements. Three of the five canopies were deemed to be completely successful from an operator's point of view. That is, mine management as well as the machine operator found that the canopies did not impede the operation of the machines to function with the same efficiency as before the installation of the canopies. The loader canopy, in fact, appeared to have provided a mole efficient operation of the loader by providing added safety to the operator from rib contact thus allowing him to concentrate more fully on the loading function. Operational problems were encountered with the shuttle car and the roof drill. The shuttle car canopy obstructed visibility to an objectionable amount and the roof drill canopy impeded maneuverability of the machine, more than doubling the roof bolting time.

Jan 1, 2012

By R. W. Smith, S. H. Ash

Marked progress in safety has characterized the operation of coal mines in general in the State of Washington during the 5- year period 1928-1932 , particularly during the years 1931 and 1932. Physical conditions such as steep pitches , inherently bad roof and floor , prevalence of gas , and explosibility of the dust of Washington coals present certain definite hazards . Although advances have been made in accident reduction in Washington , the State still has far to go in that direction . The State has endeavored to reduce its coal -mine accidents by the usual method of making certain definite safety requirements mandatory . The value of education has not been underrated , but the educational method used has not altogether achieved the res lts desired by the industry itself , particularly within certain imdividual organizations . The past 2 years have witnessed a growth , in certain instances , of the essential ideas that the observance of safety precautions on the part of all is demanded if accidents are to be reduced , and that the initiating and carrying out of any program to promote and obtain desired results in accident elimination must begin and function from the top downward . Mining operations of Washington mines have been described in various publications of the United States Bureau of Mines .

Jun 1, 1933

By George S. Scott

The Bureau of Mines conducted ignition, flammability, and decomposition experiments on gas mixtures containing ethylene to determine its flammability characteristics at elevated pressures and ambient temperatures. Pure ethylene was found to propagate a decomposition reaction at 1,000 psig and ambient temperatures when ignited with 1 gram or more of guncotton in a 2-inch-id bomb. The decomposition products were primarily carbon, methane, and hydrogen.

Jan 1, 1965

By L. Crocker

The Bureau of Mines investigated processes for recovering a marketable lithium product from the montmorillonite-type clays of the McDermitt caldera. The clay deposit, located on the Nevada-Oregon border, is estimated to contain over 3 million short tons of lithium. Limestone-gypsum roasting and selective chlorination proved most successful for extracting lithium from the clays; 80-pct Li recovery was achieved using either technique. With both processes, lithium silicate in the clay was converted to a water-soluble compound-either lithium sulfate or lithium chloride. The lithium was then recovered as a carbonate by water leaching the calcine, concentrating the leach solution by evaporation, and precipitating the lithium with soda ash. The operating costs for the limestone-gypsum roast process were estimated at $2.02/lb Li2C03; selective chlorination operating costs were estimated at $3.85/1b Li2C03. The current selling price of Li2C03 is about $1.50/lb. A detailed flowsheet, material balance, and process evaluation are presented for the limestone-gypsum roast process. In addition, lithium reserves and resources are discussed and the McDermitt clays are described.

Jan 1, 1988

By Paul Averitt

The coal-bearing rocks in Iowa occur in an arcuate belt across the central and southern parts of the State (fig. 1) at the northern end of the Western Interior coal field. Coal beds of minable thickness are sporadic throughout this area and are mined principally in the three districts indicated by dark shading on the index map, although coal occurs also in the areas indicated by light shading. The coal is mostly of high-volatile C bituminous rank in all parts of the State. SURFACE FEATURES The coal-bearing rocks in Iowa are concealed for the most part by a covering of glacial drift ranging in thickness from a few feet to several hundred feet. This covering has been dissected to form a gently rolling upland, rising from an elevation of 466 feet at the mouth of the Des Moines River to about 1,200 feet in Calhoun County in the central part of the State. The local relief, however, rarely exceeds 150 to 200 feet.

Jan 1, 1949

Arsenic.--Inorganic arsenic has been added to the Environmental Protection Agency's list of hazardous air pollutants because of a high probability it can cause cancer. EPA estimates that inorganic arsenic emissions into ambient air total more than 6,000 tons per year, with about 65;L of this coming from the operations of copper, lead, and zinc smelters. Asbestos Detection.--In June 14, the President signed S. 1658 providing $172.5 million to detect and remove asbestos hazards in schools. Asbestos Use Must be Reported.--All firms using asbestos in the manufacture of some 30 categories of products must describe in detail how they use the mineral to the Consumer Product Safety Commission, for all manufactures since January 1, 1977.

Jan 1, 1980

By Others, C. M. Weld

During the past two years the Bureau of Mines has issued a series of mimeographed reports giving the results of research work and experiments conducted as part of its war minerals investigations. In this bulletin the reports on manganese are presented, which range in scope from the beneficiation of the ore to the utilization of the metal. The bulletin is in eleven chapters, each comprising a separate report, arranged in the order given below. 1. General information regarding manganese, by C. M. Weld. 2. Uses of manganese other than in steel making, by W. C. Phalen. 3. Problems involved in the concentration and utilization of domestic low-grade manganese ores, by Edmund Newton. 4. Preparation of manganese ore, by W. R. Crane. 5. Leaching of manganese ores with sulphur dioxide, by C. E. Van Barneveld. 6. The Jones process for concentrating manganese ores; results of laboratory investigations, by Peter Christianson and W. H. Hunter. 7. Cost of producing ferromanganese ores, by C. M. Weld and W. R. Crane. 8. Production of manganese alloys in the blast furnace, by P. H. Royster. 9. National importance of allocating low-ash coke to the man- ganese-alloy furnaces, by P. H. Royster. 10. Electric smelting of domestic manganese ores, by H. W. Gillett and C. E. Williams. 11. Use of manganese alloys in open-hearth steel practice, by Samuel L. Hoyt. As each chapter was originally prepared as a unit, there is neces- sarily some duplication and overlapping. With certain exceptions, however, each paper is reproduced in practically its original form. In chapter 1, covering certain general phases of the industry, such as uses, specifications, prices, and statistics, the subject matter has been somewhat modified in view of changes in conditions.About 95 per cent of the manganese consumed in the United States goes into the manufacture of steel. The remaining 5 per cent is used in a number of minor industries, the chief of which is the manufacture of dry cells. These minor uses are described in chapter 2. No discussion of the geology of manganese eres is presented, but a short bibliography on the subject is appended. With few excep- tions the manganese deposits of the United States are irregular, pockety, and uncertain. Largely for this reason, mining methods are crude and hardly warrant descriptions. The concentration of manganese ores, however, is an important problem and involves some details not common to other ores. Chapter 3 discusses the concentration and utilization of low-grade ones, notes the relationship of concentration to metallurgical prao- tices, outlines concentrating processes, and treats of commercial problems. In general, as regards concentration methods, manganese ores may be divided into two groups, as follows: (1) Ores permitting mechanical separation of the manganese minerals and the gangue, and (2) ores in which the manganese minerals and the gangues are so intimately associated that separation requires some hydrometal- lurgical or pyrometallurgical process. Heretofore, attention has been confined almost wholly to mechanical separation, chiefly by gravity. In fact, so far as known, all production of concentrates has been by wet gravity methods, although during the war some companies investigated the commercial pessibilities of magnetic separation and reported favorable results, the construction of one magnetic con- centration mill being started. The usual wet gravity methods are described in chapter 4. During the war, the Bureau of Mines undertook investigations of methods applicable to ores of group 2. A hydrometallurgical process involving leaching with sulphur dioxide was studied at the mining experiment station of the bureau at Tucson, Ariz. The results of this work, presented in chapter 5, indicate that the process is metallurgically feasible but the cost makes it unattractive. The results of an investigation of a pyrometallurgical process known as the Jones process are presented in chapter 6. The process, which is still in the experimental stage, was found to be metal- lurgically sound. The manganese product is not a concentrate but an alloy, made directly from a lean unconcentrated ore. The custom- ary method is to manufacture alloys from high-grade ores or from concentrates of leaner ores. A discussion of the costs of ferro-grade manganese ores is pre- sented in chapter 7. This discussion is in general terms only, but should be of use in so far as it relates to competitive conditions.

Jan 1, 1920

By Francis X. Cannaday

The Bureau of Mines developed equipment to measure the sonic velocity of pulses transmitted through rock samples varying in size from laboratory specimens to mine pillars in place. Pulses are produced by electronically excited piezoelectric ceramic transducers. Special equipment components were developed by Bureau facilities; other components are commercially available. The technique permits a nondestructive, repetitive, stable, shaped pulse to be used in place of explosive caps or hammer blows. Longitudinal wave travel time measurements were taken on an oscilloscope screen; transverse wave measurements were taken under special field conditions. Results were consistently repeatable within the accuracy of the oscilloscopes utilized.

Jan 1, 1966