Search Documents

By G. L. Anderson

The U.S. Bureau of Mines (USBM) has conducted research to improve the nondestructive testing (NDT) of wire hoist ropes. Losses in the diameter of a wire hoist rope are used as one criterion for judging when a rope should be replaced. Losses are determined by periodically measuring the rope diameter and comparing this measurement with the original measured diameter; when the diameter reaches a specified minimum at any point along its length, the rope must be retired. Generally, these measurements are made at randomly selected locations along the length of the rope, using a hand caliper. To provide more accurate measurements and to allow measurements to be taken continuously along the length of a hoist rope, an optical diameter-monitoring system was built for the USBM under contract. Continuous measurements are preferable because, when combined with continuous electro-magnetic NDT results, they can indicate whether losses in metallic cross-sectional area originate from external wear or internal wear and corrosion. Tests of the system showed that the instrument met specifications when measuring wire rope at low rope speeds but was inaccurate at speeds over about 30 m/min (100 ft/min). This report describes the prototype system, presents the results of the test program, and describes the capabilities of the system.

Jan 1, 2010

By D. J. Parker, D. Harrington, L. H. Harrison

"INTRODUCTION The necessity for protection against the hazards of lightning manifests itself from time to time in the mining industry by reason of loss of life, damage to electrical equipment, fires in surface structures at mines, and accidents in the handling and use of explosives. This paper is intended to assemble, correlate, and present some of the salient points embodied in the available literature on the subject and at the same time give some factual data concerning instances of such loss of life and damage to property, with special application to the mining industry.The annual loss of life and destruction of property by lightning is considerable; the former may be prevented to a limited extent, though use of common sense as to exposure is required and not always followed; the latter can be prevented to a considerable degree. The manufacturers of electrical equipment, through improved types of lightning arresters, have done much toward the protection of electrical equipment, with consequent safeguarding of life and of property. Education based on unfortunate experiences has gone far to discourage the handling of explosives and blasting accessories during thunder storms, especially in open pits and quarries, and to a much smaller extent in underground workings. The lowly lightning rod plays an important role in the protection of certain types of buildings (especially isolated buildings), stacks, monuments, and other structures.LIGHTNING PHENOMENAIn 1751, Franklin proved that, lightning was simply a visible display of electricity - an extended spark; and until a generation ago little had been added to his exposition to define the various phases of the phenomenon. Matters pertaining to lightning are discussed in the following references:"

Apr 1, 1948

By E. D. Gardner

This paper is the third of a series of three on placer mining in the western United States. The first paper4 discusses the history of placer mining in the Western States and the production of placer gold, geology of placer deposits, location of placer claims on public lands, sampling and estimation of gold placers, and classification of placer-mining methods, together with hand-shoveling and ground-sluicing. The second papers deals with hydraulicking, sluice boxes and riffles, recovery of gold and platinum from placer concentrates, treatment of amalgam, and marketing of placer gold. The discussion of sluice boxes and subsequent subjects in the second paper applies to all forms of placer mining. The present paper treats of dredging and other forms of mechanical handling of placer gravels, and drift mining.

Jan 1, 1934

By W. J. Campbell

This report by the Federal Bureau of Mines Particulate Mineralogy Unit recommends mineralogical definitions and identification-characterization concepts for selected silicate minerals and their asbestiform varieties. Precise definitions acceptable to mineral analysts, regulatory personnel, and medical scientists are essential because of the present lack of conformity in terminology concerned with measuring and controlling asbestiform particulates and their related health effects. Because of the complexity and variability of crystal morphology in different mineral groups, the descriptive terms are generally explained by illustration rather than by numerical values. Applications and limitations of several analytical techniques for particulate identification and characterization are discussed.

Jan 1, 1977

This report describes Phase I of the project --Development of a Mechanized Scaler --performed by Battelle, Pacific Northwest Laboratories for the U.S. Bureau of Mines. The objectives of Phase I were to 1) assess the needs of the industry as related to mechanized scaling; 2) conceive, evaluate and select mechanized scaler concepts; and 3) prepare preliminary designs of the selected machine concepts. To assess the scaling needs of the industry, we reviewed both U.S. and foreign literature, evaluated U.S. scaling accident statistics, reviewed existing mechanized scaling equipment, performed a series of mine visits and telephone interviews with mine operators, and assessed the applicability of a loose-rock detection system. The literature review identified over 25 scaler-related articles. However, little of the information could be used directly in the conceptualization and design portions of the project. Three articles did supply information on a number of machines used in Europe, along with statistics describing their effect on mine safety. For example, the French reported a 50% reduction in the total number of scaling-related accidents and a full 80% reduction in the number of lost-time injuries in the Lorraine mining district.

Jan 1, 1981

By Michael J. Friedel

As part of an investigation aimed at mitigating the hazards caused by abandoned mine openings, the Bureau of Mines conducted a series of electromagnetic surveys in the Galena, KS, area of the Tri-State mining district. The application of monostatic ground-penetrating radar (OPR) and inductive electromagnetic methods for detecting and delineating hazardous mine openings and attendant features was demonstrated to be feasible for shallow mine workings (i.e., less than 35 ft) occurring below flat-lying areas. Accurate determinations of depth to a mine roof appeared to be limited to roughly 20 ft using the GPR method. Features such as mine voids, fractures, and zones of subsidence were located beneath the Mainstreet (State Highway 26) site using the GPR system. Both the GPR and inductive electromagnetic techniques satisfactorily located mine openings and pillars at the Hell's Half Acre site. Geophysical interpretations were supported by exploratory drilling and mine maps.

Jan 1, 1990

By Seth T. Reese

THE INJURY DATA and experience at coal mines in the United States for 1951 are presented in this bulletin under the following general heads: (A) General injury experience: Tables 1 to 18: Contain current data on number of fatalities and nonfatal injuries, frequency and severity rates, average severity, major and detailed injury agencies, and distribution of injuries by part of body and days of disability. (B) Selected injury data: Tables 19 to 43: Contain current data on various selected factors of operating and physical conditions that contributed to the occurrence of injuries at bituminous-coal, lignite, and anthracite mines. These factors include extent of hand and machine loading, size of mine by employment and production groups, thickness of bed or vein, duration and number of work shifts, rating of mine as gassy or nongassy, types of cap lamps, explosives, and combination of factors that influence mine safety. (C) Injury experience by States: Tables 44 to 50: Contain current data on number of fatalities and nonfatal injuries, frequency and severity rates, average severity, major causes and principal agencies, injury records of all coal-producing States, and the relative standing by States according to injury-frequency rates. (D) Major disasters: Table 51: Lists the coal-mine disasters that occurred during 1951, giving location, source, and cause. A major disaster in coal mining is defined as a single accident in which or as a result of which five or more men lost their lives. (E) Historical coal-mine injury experience: Tables 52 to 86: Contain data on injuries, injury-frequency rates, employment, and production at bituminous-coal, lignite, and anthracite mines from the earliest records through 1951.

Jan 1, 1955

By S. H. Ash

THE BARRIER-PILLAR SYSTEM in the Lackawanna Basin consists of 93 barrier pillars between Archbald and Taylor, Pa. These pillars affect 48 mines, have a total length of 87 miles, and confine 21 underground pools, which contain more than 10 billion gallons of water. From an investigation of size, position, and condition of the barrier pillars, it is apparent that those concerned are uncertain, not only as to the method by which the sizes of the barrier pillars were determined but also as to the stability of those that may be expected to act as dams. Where a barrier pillar must act as a dam, its failure may result in loss of life, the mine, or both; it would be far better had it not existed and thereby given a false sense of security.

Jan 1, 1952

By R. A. Cortese

The U.S. Bureau of Mines has developed a flame-radiation-powered trigger device to explosively activate suppression barriers to quench gas and coal dust explosions. The major component of the device is a silicon solar panel, which converts radiation from the developing explosion into electrical energy to initiate an electric detonator, which releases an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 W of electrical power when exposed to the sunlight are producing about 200 W when exposed to a full-scale dust explosion. The solar panel is electrically isolated from the detonator by a pressure-sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame-powered photogenerator prevents false barrier activation and requires no external power supply.

Jan 1, 2010

These proceedings consist of an introduction, nine descriptive papers, and a summary. The first paper is an overview of the respirable dust research program, the second paper describes the Mining Enforcement and Safety Administration's proposed changes in the respirable dust enforcement program, and the third paper describes respirable dust measurement. The remaining papers, by Bureau and contractor personnel, describes methods of reducing the amount of respirable dust to which coal miners are exposed. Of the six methods of reducing exposure to respirable dust described, two are methods of preventing or reducing the amount of respirable dust raised during mining operations, two are methods of collecting or removing dust after it has been released into the mine atmosphere, 2nd two describe methods that are combinations of prevention and collecting .

Jan 1, 1977

By Kenneth E. Hjelmstad

The U.S. Bureau of Mines (USBM) has developed an electromagnetic (EM) fire warning alarm sys-tem for underground mines. The system generates a magnetic field for through-the-earth signal trans-mission to microreceivers carried by individual miners. EM fields can induce electric currents in metallic conductors; if an EM transmitting antenna and an electric blasting cap array are too close, the field could induce a current in the blasting array and cause an unintentional initiation of the electric detonators. The USBM conducted tests that define the safe and unsafe regions for using electric detonators near the transmitting antenna of the warning alarm system. The minimum safe distance between a transmitting antenna and a blasting array is the distance where the induced electrical current in the blasting array is 50 mA, which is the safe current level specified in Federal mine safety regulations. Tests indicate that at transmitting power levels of 100-and 1,000-W, separation distances of 9 and 21 m, respectively, were required. These distances are small compared with the dimensions of a mine. Thus, the tests indicate that, with proper placement of the transmitting antenna, the warning system can be used safely in the proximity of blasting arrays.

Jan 1, 2010

6889. Aslakson, C. I., and Swick, C. H. Gravity Observations in Peru and Colombia. Coast and Geodetic Survey,-Special Pub. 233, U. S. Government Printing Office, Washington, D. C., 1943, 18 pp. (Price, 10 cents.) In accordance with the policy of cooperation among American republics, the-United States Coast and Geodetic Survey in 1941 made gravity surveys in Peru and-Colombia. The information was desirable for determining the figure of the earth for geophysical purposes and for studying the relationship between intensities of gravity and deflections of the vertical. The survey instrument was the Brown pendulum apparatus. 11 gravity stations were established in Peru and 13 in Colombia. The results obtained at these stations are given in a table covering observed gravity, theoretical gravity, and anamalies. - V. S.

Jan 1, 1943

By R. Y. Williams

The investigative work described in this report was undertaken by the Bureau of Mines under a cooperative agreement with the department of mining engineering of the University of Illinois and the Illinois State Geological Survey." The purpose of this agreement was to provide for a comprehensive investigation of coal-mining conditions in the State, with especial reference to the possibility of lessening waste in the mining and preparation of coal and of reducing the dangers to which miners are exposed. The Bureau of Mines paid particular attention to those phases of the investigation that were of general interest from their bearing on safety and efficiency in the coal-mining industry as a whole. Thus, it studied the occurrence of gas (methane) in the mines of the southern part of the State," tested the inflammability of the coal dust from many mines, examined the efficiency of the control of ventilating currents, and investigated the factors affecting the humidity of mine air with respect to their bearing on the occurrence of mine explosions. Following the establishment of the fact that under certain conditions dry bituminous coal dust is inflammable, there arose the problem of finding efficient methods of preventing or limiting coal-dust explosions. Experiments in the gas-and-dust gallery at the Pittsburgh testing station of the Bureau of Mines verified the fact that certain dusts that explode violently when dry are rendered inert by proper humidi- .fication of the atmosphere within the gallery, and the importance of humidity as a factor in limiting the inflammability of coal dust in a mine is demonstrated by the fact that there has never been in Illinois a dust explosion during the summer months, whereas the records show a number of dust explosions during cold weather. It is easy to see that the warm moisture-laden air that enters a mine in the summer must deposit moisture on cooling, whereas the cold and relatively dry air that enters in winter must take up moisture as it becomes heated in traveling through the mine.

Jan 1, 1914

By Edward A. McClatchie

A novel nondispersive electro-optical gas analyzer has been designed, fabricated and tested. The instrument is based on a pressure modulated absorption technique. Key features of this new gas analyzer technique include long-term zero and calibration stability. The technique was investigated for the gases carbon dioxide (CO2), carbon monoxide (CO), methane (CH4) and nitrogen dioxide (NO2). The delivered analyzer was capable of measuring the three species CO, CO2 and NO2. It is a compact (300 cu in) package, is battery powered and weighs 15 lbs. Some thirty readings of each gas may be made on a single battery charge.

Jan 1, 1980

By William D. Monaghan

The U.S. Bureau of Mines evaluated a teleoperated continuous mining machine for deep mining in thin-seam applications as low as 1 m. Teleoperation increases the safety of mining machine operators because it removes the operator from the face, an area of immediate hazards to safer outby locations. By using teleoperation, the miner can avoid many including unexpected roof falls that can maim or kill miners instantly, methane and coal dust explosions that can be ignited with just a small spark or flame, adverse health effects from miners breathing coal and silica dust, adverse long-term inner ear damage from loud noise pollution, and other hazards related to heavy mining equipment moving about in confined underground roadways. This report presents the surface evaluation results of a teleoperated control system.

Jan 1, 1994

By J. J. Forbes

Since 1910 the Bureau of Mines has given training in the care and use of oxygen breathing apparatus under conditions that may exist during mine fires and after mine explosions. In 1929 the Bureau supplemented this instruction by initiating a course in advanced mine rescue training to prepare mine officials and others to organize men for mine rescue and recovery operations. The course of instruction has been developed and expanded since its inception to keep abreast with new ideas, methods, and equipment. Four miners' circulars were issued to be used in the training course. The first of this series (Miners' Circular 33) deals with mine gases and the various methods of detecting them; the second (Miners' Circular 34) gives instructions for sampling and analyzing mine atmospheres; the third (this circular) describes methods and equipment for protection against mine gases; and the fourth (Miners' Circular 36) explains procedures in sealing and unsealing mine fires and in conducting recovery operations, These circulars have been revised from time to time to keep them up to date.

Jan 1, 1954

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company's Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963

By D. D. Southworth

In 1987, the Bureau of Mines initiated a mineral assessment of the 5.7 million-acre Valdez Creek Mining District (VCMD). Following a literature search and interviews with persons knowledgeable about deposits within the district, limited on-site field visits were made to various deposits. Present within the district are the industrial minerals limestone, argillite, granite, basalt, perlite, zeolite, and sand and gravel. At least six limestone deposits of potentially economic size and grade are known to exist within the district. Adjacent to the Parks Highway and marginal to the district, a limestone deposit is currently being mined as a source of agricultural lime. A perlite occurrence near Yacko Creek was evaluated but proved not to be of industrial grade. The sand-and-gravel resources of the district are vast, but high silt content renders many of the glacial deposits unsuitable for use in construction applications.

Jan 1, 2011

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of canopy air curtain devices under Bureau of Mines Contract H0232067. The canopy air curtain device is designed to reduce the level of respirable dust exposure to a continuous mining machine operator while having a minimum effect on operator safety, mobility and comfort and being compatible with mining equipment. This contract was devoted to the development of a device which utilizes an invisible curtain of air to envelope a mining machine operator's breathing zone with filtered air to provide respiratory protection. Various concepts were evaluated by means of laboratory tests. One concept was selected and was tested on various mining machines at underground sites by means of MSA personal samplers. The canopy air curtain was found to be effective. The percent reductions over the ambient dust concentrations were about 30 to 75 percent depending on the amount of time the operator spent under the air curtain. At one test site, the device enabled the mining machine to operate within compliance. Donaldson Company is presently working on the commercial production of the device.

Jan 1, 1975

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures area discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of mining modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mine is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964