Search Documents

By James C. Cawley

The Bureau of Mines conducted an investigation to statistically determine the mean current or voltage for resistive, inductive, and capaci-tive circuits that would cause spark ignitions in 8.3% methane-air, 5.3% propane-air, and 7.8% ethylene-air mixtures. Each mean ignition current or voltage was determined on the basis of 100 trials. Each trial consisted of 400 revolutions, 200 in each polarity, at 80 rpm of the standard breakf1ash apparatus. In general, spark ignition curves published in UL 913 for resistive and inductive circuits represent approximately the mean current values determined in this study, while published capacitive circuit values in methane are considerably less than the mean voltage values from this study, especially for a capacitance of less than 100 ~F. For resistive and inductive circuits, spark ignitions were obtained at currents con-siderably below those in the published curves, but this study was not optimized to find minimum ignition values. This report defines "safety factor" as applied to intrinsic safety testing as the energy ratio of the mean values of ignition current or voltage for two test gases. The safety factors presented in this report are not constant with voltage or current and, therefore, are not recommended for use.

Jan 1, 1986

By Donna L. Anderson

This U.S. Bureau of Mines report discusses the status of a laser-based guidance system to provide position and heading feedback and closed-loop control of tramming maneuvers for a continuous mining machine. The system has been developed and tested at the Bureau, and is now being prepared for underground experiments. The system hardware includes laser scanners, a sensor communication network, and host computer hardware. The system software includes a position and heading computation module and a tram control module. The description of the software includes discussions of laser data acquisition, error compensation methods, position and heading determination, safety checking for continuous miner tramming, and closed-loop tram control. The accuracy of the laser scanner's data, the reliability of the lasers in a dusty environment, and the system's accuracy on tracking the position and heading of the continuous mining machine are shown in the results of experiments performed at the Bureau. Conclusions are stated based on these experimental results, and further work to improve the system performance and prepare for underground testing is discussed.

Jan 1, 1990

Commodities statistics and otter information are available through the following t et systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By W. R. K. Wu

This bulletin traces the development of high-pressure, coal and tar hydrogenation technology, based on an intensive review of the pertinent literature. The bulletin was written as a part of the Bureau of Mines research program on synthetic liquid fuels. It covers the history and economics of the process; the chemical aspect of hydrogenation of coal, tar, and middle oil; the engineering aspect of converting coal and tar to liquid fuels, principally gasoline; and the equipment for the process. The literature covered includes documents of the United States and British Governments, journals, and other publications. Bureau results in the hydrogenation field are also incorporated.

Jan 1, 1968

By J. S. Hansen

The U.S. Bureau of Mines developed a system for casting unique, slotted steel armor by modifying the conventional expendable pattern casting (EPC) process that is normally used for making aluminum castings. Three innovations were added to the EPC process to make the successful adaptation: (1) Vacuum was applied to sand molds, (2) continuous narrow-necked feeding systems were used to permit the casting of thin walls, and (3) fixtures were designed to prevent pattern damage and to hold critical casting tolerances, Potential problems and defects are described.

Jan 1, 2010

By Homer J. Ballinger

The Alma, Degraff and other mines controlled by the Mon-Ark Mining Co. comprise one of the more important groups of zinc-lead mines in Christian County, Mo. The mines were first operated in .1857 and produced more than 5 million pounds of lead from rich, shallow ore deposits. Recent exploration and development led to the discovery of zinc sulfide ore at a depth of 165 to 214 feet in the northern part of the Alma mine. After examination of these mines in September 1942 by Bureau of Mines engineers, investigation of the extension -of the Alma mine and of the depth of mineralization at the other mines appeared justified in order to encourage the production of additional zinc and lead for war purposes. Twenty-nine churn-drill holes totaling 6.463 feet of bore were completed by the. Bureau from September 1943 to January 1944.

Jan 1, 1948

By Alexander May

The U.S. Bureau of Mines investigated the application of oxidation-reduction potential (ORP) and pH measurements to environmental studies of mining and mineral processing wastes, and developed a computer program to estimate the concentrations of species of lead present in samples from a lead processing waste site. The methods and techniques for the ORP-pH measurements were investigated using known standard solutions made in the laboratory, samples from a ferric oxide waste disposal pond at a rutile production plant, and samples of well water and stream water from the lead processing waste site. ORP values were measured from 5 to 80 °C, from pH 1 to pH 12, and at various ratios of oxidant to reductant. The ORP-pH values can help identify valence values and species of ions present, including those of major, minor, and trace concentrations, and also indicate possible reactions at various pH values. The ORP measurements versus temperature yield data from which thermodynamic values can be calculated. The application and limitations of these measurements are discussed, and a brief discussion of the computational program to identify species of lead is presented.

Jan 1, 2010

By R. H. Storch, D. C. Holt

During reconnaissance investigations of more than 300 stream areas in Idaho to determine the potential value of ilmenite in black - sand placer deposits 46 deposits were explored by churn drilling , trenching , test pitting , or shafting . The component mineral content and total black - sand content were determined for more than 8,690 reconnaissance and exploration samples . Data compiled during the investigation indicate a good potential for large , low- grade deposits containing ilmenite , monazite , columbite , euxenite , uranothorite , and other radioactive black minerals and accessory black - sand minerals . The data also indicate most deposits will be economic only if several component minerals can be recovered as coproducts .

Jan 1, 1963

By P. H. Mutschler

The Bureau of Mines studied the Chattanooga Shale to determine the quantity and quality of the uranium resources present and to assess specific environmental effects of mining the shale. Geologic data and chemical analyses, mainly concerning a 12-county area of Tennessee, were compiled from previous published and unpublished reports. Uranium resources in the Gassaway Member of the Chattanooga Shale in this 12-county area were estimated to be between 4.2 and 5.1 million tons, contained in 76 to 91 billion tons of shale. These figures represent inground tonnages and do not allow for mining or processing losses. Depending upon efficiency of mining and processing systems, enough uranium could be available to satisfy a large part of the cumulative domestic and world demand through the year 2000. A model was developed which assesses the total tons or acres of shale to be mined if the Gassaway Member were to satisfy 1 percent of the United States demand for uranium in 1991. This partially demonstrates the environmental impact of mining the shale and is easily factorable to any specified demand.

Jan 1, 1976

By John F. Papp

The objective of this U.S. Bureau of Mines study is to calculate an accurate, reliable estimate of chromium and nickel content of stainless and heat-resisting steel produced in the United States. The columbium, manganese, molybdenum, titanium, tungsten, and vanadium contents of this steel are also calculated. Such contents are required for estimating the quantity of alloying element recovered from recycled stainless steel and consumed by market sectors. In this investigation, the elemental fraction of stainless and heat-resisting steel was calculated as the ratio of the weight of element contained in stainless steel to the weight of stainless steel produced. The elemental fraction has been calculated as a time-averaged, grade-averaged value. The elemental fraction was averaged from 1962 through 1983, and averaged over the grades for which production was reported by the American Iron and Steel Institute during that time period. The 1962-83 average elemental fraction of U.S.-produced stainless and heat-resisting steel was calculated for chromium to be about 0.17 ± 0.01; columbium, 0.00014 ± 0.00003; manganese, 0.015 ± 0.005; molybdenum, 0.004 ± 0.001; nickel, 0.07 ± 0.01; silicon, 0.009 ± 0.001; titanium, 0.0004 ± 0.0001; tungsten, 0.0001±0.00003; and vanadium, 0.00003±0.0000l.

Jan 1, 1991

By J. D. Davis

The carbonizing properties of No. 2-bed coal from the Bartoy mine and No. 5- or Miller-bed coal from the Wilkeson-Miller mine, both at Wilkeson, Pierce County, Wash., were determined by the Bureau of Mines-American Gas Association (BM-AGA) method. Tests were made in the 13-inch retort at 500°, 600°, and 700° C. and in the 18¬inch retort at 800°, 900°, and 1,000° C. Fischer low-temperature and United States Steel Corporation high-temperature assays were made and the results compared with those of the BM-AGA tests at corresponding temperatures. Agglutinating and plastic properties were determined, and chemical and petrographic analyses were made. The No. 2 bed is 58.5 to 88.0 inches thick at three points sampled in the Bartoy mine. The coal is 98 percent bright and contains only a trace of fusain. A composite of three mine samples contained 13.8 percent ash. The washed sample, which was used in the tests described herein, contained 11.4 percent ash, 2.2 percent moisture, and 0.6 percent sulfur upon the as-carbonized basis and 68.4 percent fixed carbon upon the dry, mineral-matter-free basis. The heating value was 15,183 B. t.u. per pound upon the moist, mineral-matter-free basis. No. 2 therefore ranks as a high-volatile A coal and is very high in that, rank. The ash softens at 2,910° F. Except for its ash content, which is higher than the limit of 9.0 percent specified by the American Society for Testing Materials, No. 2 coal fulfills the requirements of a coking coal. It also is classed as extremely friable, the friability being 88.0 percent. The agglutinating index (7.6 for the 15 : 1 ratio of silicon carbide to coal) is high, and the plasticity as indicated by the Gieseler test (60 divisions per minute) is low for a high-volatile A coal.

Jan 1, 1942

This volume constitutes the final report for the Rescue Subsystem portion of the Coal Mine Rescue and Survival System program conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated Jung 17, 1970). The program was directed by the Special Systems Department of the Westinghouse, Baltimore, Maryland facility. The basic objectives of the CMRSS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major- sources: the Request for Proposal from the Bureau of Mines and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering (NAE).

Jan 1, 1971

By Thomas Brunsing

The program was carried out to develop deep kerfing and core breaking techniques to be incorporated into the design of a field prototype hard rock mining machine. The field machine is designed to mine non-abrasive bedded deposits up to 20,000 psi in uniaxial compressive strength. The mining technique involves cutting approximately 2 ft deep parallel kerfs spaced 2 ft apart in either a horizontal or vertical direction and subsequently breaking out the cores so defined. The prototype machine is intended for demonstration of the technique in a quarry or equivalent field environment. The program was aimed at minimizing the required kerf width, obtaining reliable breaking within that kerf width and determining cutter blade requirements necessary to achieve a mining rate of 20 ft3/min. Full scale breaking experiments and 1/2 scale kerfing experiments were employed to evaluate the system. High strength concrete test specimens were used to simulate the rock being cut and broken. The test results indicate the kerf/break technique can achieve the desired mining rate by utilizing two 7 ft diam blades to cut 2 in. wide by 24 in. deep kerfs. A lateral load applied at the base of the kerf (base shear) was selected at the core breaking technique to be employed by the full-scale prototype machine.

Jan 1, 1983

Seventy-three of the 90 naturally occurring elements that are found in the earth's crust are metals or metalloids. The quantities of metals used annually in the United States range from about 100 million metric tons (steel) to a few kilograms (osmium). The recovery of metals from discarded products or industrial process wastes, especially those metals that are used in large quantity, are very expensive, or are unusually toxic, is important to the national economy and to the natural environment. From its inception in 1910, the U.S. Bureau of Mines (USBM) has been the Government's prime source of information on metals recycling, as well as a major innovator in recycling technology. Statistical data on scrap generation and processing have been summarized annually for many years in the USBM's Minerals Yearbook. Most of the data for individual metals discussed in this report were extracted from that publication.

Jan 1, 1993

By W. W. Adams

Every man-hour of work performed in and about the coal mines of the United States had a 2-percent heavier death load from accidents in 1938 than in 1937. This is an unorthodox way of stating that the death rate per million man-hours of exposure or employment was 2 percent higher in 1938 than in 1937, increasing from 1.74 to 1.78. Thus the average miner had a 2-percent greater chance of being killed in 1938 than he had in 1937. The average quantity of coal resulting from 1 man-hour of work increased 3.6 percent -from 0.615 ton in 1937 to 0.637 ton in 1938. The production of the average ton of coal was accompanied by a slightly smaller loss of life in 1938 than in 1937, the accident rate being 2.793 per million tons in 1938 compared with 2.833 in 1937.

Jan 1, 1941

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., Lafayette, CA, under contract to the U.S. Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1990

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States from 1961 through 1967. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included.

Jan 1, 1969

By Sara J. Davenport

With the increased demand for mercury incident to preparations for national defense and the reduction in imports from some of the usual sources owing to war conditions, many small mines in the United States Pure now being worked that ordinarily would be unprofitable. This is indicated by the following table on mercury produced in the Unite States in 1939-40 (1)4/

Jan 1, 1941

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By Harold M. Smith

[Important discoveries of new oil fields were made in 1937 in the State of Illinois. Oil production, which was virtually constant during 1934, 1935, and 1936 at about 4,400,000 barrels a year, a increased to 7,499,000, barrels during 1937, and in 1938 this production was trebled. In 1939, 94,302,0003/ barrels were produced (almost foot times the 1938 quantity), making Illinois one of the cost important oil-producing areas in the United States. The Bureau of Mines has analyzed 35 samples of petroleum from these new Illinois fields and presents the analyses herein. Included with them in this report are analyses of seven samples from fields developed before 1936.]

Jan 1, 1940