Search Documents

By Arthur E. Bruszak, Marcel Vanpée

In many practical combustion systems ignition may occur through contact with hot burned gases . Such a process plays a vital role in flame stabilization on bluff bodies . It is also of importance in the ignition of firedamp by the hot spent gases of explosives used in mines . Also , in the communication of flames through narrow channels , a problem of practical importance in flameproofing electrical equipment , the propagation of the flame is essentially a reignition process in which hot burned gases are the agent of ignition . In the actual ignition problem a great variety of conditions may be visualized . Ignition may occur where pockets of hot gases are surrounded by cold explosive mixtures or where pockets of cold mixture may be surrounded by hot gases . Alternately , a flowing stream of combustible mixture may be initially in contact with another stream of hot combustion products , or a jet of hot gases may flow into a cold quiescent mixture ; the jet may be laminar or turbulent , continuous or discontinuous . The hot gas may also consist of the oxidant ( air for instance ) and the cold combustible pure fuel . This study by the Bureau of Mines is concerned only with ignition produced by a continuous jet of gas ( hot ) flowing into a practically quiescent cold mix- The investigation of ignition by bursts of hot gases or by turbulent jets is outside the scope of this report , and work performed on this phase of the problem has been published elsewhere

Jan 1, 1963

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By Kim B. Shedd

The Bureau of Mines measured fiber dimensions on crocidolites (riebeckite-asbestos and magnesioriebeckite-asbestos) from the world's four crocidolite mining regions. The objective of the study was to determine whether there are measurable morphological differences between crocidolite fibers that correlate with the high reported incidence of mesothelioma in miners and mill employees in the Cape Province of South Africa and Western Australia, as compared with little or no reported incidence of this cancer in the Transvaal Province of South Africa or Bolivia. Fiber dimensions measured with the scanning transmission elec-tron microscope showed that crocidolites from Western Australia and the Cape Province have more thin fibers than crocidolites from Bolivia and the Transvaal Province.

Jan 1, 1985

By R. V. Lundquist, H. Leitch

The solubility characteristics of three calcium aluminates , 12Ca0 · 7A120½ 3Ca0 A1203 , and 4Ca0 A12 03 Fe2O3 , were determined in water and in solutions of NaOH and Na₂ CO₂ to more clearly define their role in relation to the recovery of aluminum by the lime sinter and the lime - soda sinter processes . The calcium aluminates were prepared by sintering stoichiometric mixtures of CaCO3 , Al2O3 3H20, and Fe 0 at 1,375 ° C. The rates and extent of aluminum extractions were determined . The aluminum extractions from the aluminates were dependent on the presence of carbonate ions in the leach solutions , temperature , time , leach solution composition , and solid - liquid ratio of the slurry . The aluminum extracted from the calcium aluminates in water and in NaOH solutions varied from 4.6 to 22.9 percent . Virtually , complete extraction could generally be obtained for 12Ca0.7A120 and 4Ca0.A12 03 • Fe₂ 03 ; in one instance it was obtained for 3Ca0.A1203 , when an excess of carbonate ions was present over that required for the conversion of all of the calcium in the aluminates into CaCO3 . In some cases of poor aluminum recoveries , extractions could be improved by regrinding and releaching the solid residues .

Jan 1, 1964

By D. L. Nussear, W. E. Wallace, N. N. Clark, M. Gautam, G. Hong-Guang

"Results from a study directed towards identifying and measuring the mutagenicity of diesel exhaust particulate matter involved in mining exposures, especially those which may synergistically affect genotoxic hazard, are presented in this paper. Particulate matter emissions from a diesel engine, representative of the ones found in underground mines, were sampled and assayed to determine the genotoxic potential as a function of engine operating conditions. Diesel exhaust was diluted in a multi-tube mini-dilution tunnel and the particulate matter was collected on 70 mm fluorocarbon coated glass fiber filters as well as on 8"" x 10"" hi-volume filters. A six mode steady state duty cycle was used to relate engine operating conditions to the mutagenicity potential.Protocols developed for using a primary component of pulmonary surfactant as a medium for collecting and applying respirable particulate material to cells for mutagenicity testing offer a true representation of in-vivo delivery of such respired aerosols to pulmonary cells and the genetic material within . The surfactant dispersion technique is discussed in this paper. Methods have been developed to sample and assay the diesel soot and diesel soot/mineral dust complexes which would not compromise the surface and physical properties of the particulate material."

Nov 1, 1995

By George W. Toth

Uranium in situ leach mining has recently emerged as a viable alternative to conventional miring techniques. The cost implications of in situ mining are therefore of increasing interest to mining paracticioners as well as public officials. This report presents the results of an assessment of uranium in situ leach mining costs through the application of process engineering and discounted cash flow analysis procedures. A computerized wasting technique, termed a cost model, was developed through this effort to facilitate rapid cost analyses. Application of this cost model will generate mine life capital and operating costs as well as solve for economic production cost/lb. U308. Conversely rate of return may be determined subject to a known selling price. The data bases of the cost made! have been designed to reflect variations in Texas vs. Wyoming site applications. The results If applying the model under numerous ore deposit, operating, wellfield and extraction plant conditions for Texas and Wyoming are summarized in the report. Sensitivity analysis of changes in key project parameters have also been tested and reported.

Jan 1, 1981

By Harry R. Nicholls

Six different chemical explosives were detonated in a test series to com-pare their relative performance in granite. From 5 to 255 feet from the detonation point, strain, acceleration, and particle velocity were recorded and analyzed for amplitude and pulse shape. Strain energy was calculated from strain data, and displacement data were obtained from particle velocity data by integration. The results show that explosives which have a characteristic impedance more closely matching that of the rock generate larger peak amplitudes than explosives with a lower characteristic impedance. The results also show that as the ratio of characteristic impedance of exp1osive-to-rock approaches unity, more rock is crushed and a larger percentage of the avail-able explosive energy is transferred to the rock as seismic energy. The effect of characteristic impedance is shown to be greater than the effect predicted from acoustic theory and is believed to be indicative of shock wave effects at the explosive-rock boundary.

Jan 1, 1965

Construction workers may be exposed to hazardous dust containing crystalline silica during site preparation when drilling systems are used. The National Institute for Occupational Safety and Health (NIOSH) found that drill dust could be decreased by using wet or dry dust reduction engineering controls, enclosed cabs, and implementing a dust control program.

Jan 1, 2009

By M. C. Irani

This Bureau of Mines survey of methane emissions indicates that total daily emissions have declined from 227 MM ft3 in 1971 to 214.7 MM ft3 in 1973. The highest average daily emissions in million cubic feet per day observed in U.S. bituminous coal mines were, in decreasing order, Monongalia County, W. Va., 40.7; Marion County, W. Va., 23.1; Buchanan County, Va., 22.1; Washington County, Pa. , 12.4; Greene County, Pa. , 11.7; McDowell County, W. Va. , 11.4; Cambria County, Pa., 9.8; Jefferson County, Ala., 9.5; Wyoming County, W. Va., 6.0; Marshall County, W. Va., 4.8; and Indiana County, Pa., 4.8.

Jan 1, 1974

By John C. Feeley

The methods used and the funds available for the development and oper- ation of shall mines and the reopening of small abandoned mines frequently present problems that tax the ingenuity and resourcefulness of the mining engineer far beyond that required in the mass production from large deposits. The objective of this paper is to describe in considerable detail the means whereby engineers have solved local problems in reopening an abandoned mine at which equipment, facilities, and funds were limited... The Etowah Coal & Iron Co. Gadsden red-iron-ore mine at Gadsden, Ala., 18 of interest in this category since it is the only independent red-ore mine under active development in the State. All other red-ore mines in Alabama are owned or controlled by the large iron or steel companies. The The mine, located on the southwest end of Shinbone Ridge in the outskirts of Gadsden lies in an ares once productive. but now idle, for many years. ore is relatively highgrade compared with that in the Birmingham area, but the bed is thin and somewhat lenticular. The presence of a large blast furnace at Alabama City, 3 miles from Gadsden, and the growing scarcity of red-iron ore supplies for it offered inducements for reopening the mine in 1946. Up to the time this circular was prepared (1947) only a small quantity of ore (about 1,500 tons) has been produced and shipped to the furnace. A force of 14 men was employed in sinking the main slope and developing a third "lift" (a local term for level) 100 feet below the old mine workings.

May 1, 1949

By John A. Richards

This paper is one of a series being published by the Bureau of Mines on mining methods and costs. It describes briefly the manner in which slusher hoists and scrapers are used in connection with clock-caving methods at the Emma Nevada mine of the Consolidated Coppermines Corporation, Kimberly, Nev. Kimberly is in the Robinson mining district, White Pine County, 7 miles west of Ely. The district is served by the Nevada Northern -Railroad, which branches from the main line of the Southern Pacific at Wells, Nev., 140 miles north, Paved U. S. Highway 50 from Salt Lake City, Utah, to Reno, Nev., passes through Ely. The altitude at the collar of the Emma Nevada shaft is 7117 feet. The surrounding hills are covered with a sparse growth of juniper, pinon, and mountain mahogany.

Jan 1, 1940

By Patrick D. McMaster

"INTRODUCTION According to the Roane Iron Co. of Rockwood, Tenn., the Chamberlain. Barnardville iron deposit produced approximately three million tons of iron ore previous to 1928. The deposit is divided into two synclinal bodies termed the north and south synclines. Production has come from the northern extremities of both bodies.The need for developing additional iron-ore reserves during the war prompted the Bureau of Mines to initiate an exploratory program on the Chamberlain-Barnardville deposit in February 1944, which continued until December 1944.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Oct 1, 1946

By J. E. Hipp

Three electrostatic field sensing proximity warning devices were tested using full-scale cranes and power line systems, a scaled model facility, environmental testing facilities, and theoretical/numerical analysis. The design objective of each device is to assist in safe crane operation near overhead power lines. Several design deficiencies (varying from device to device) were observed, including inadequate overlap in sensitivity ranges, utilization of vacuum tubes and electro-mechanical parts, temperature sensitivity and inaudible alarms. In addition, the testing showed major device limitations including sensitivity to boom orientations and length, polarization dependent responses, and unreliable operation in the presence of multiple power line circuits. The multiple power line circuit problem is intrinsic to electrostatic sensing devices. The remaining deficiencies and limitations are correctable within a state-of-the-art design. This investigation is not intended to evaluate the safety aspects or policy of utilizing proximity warning devices. Rather, the purpose is to determine the performance characteristics of such devices in relation to the criteria specified in proposed MSHA regulation 77.805-4 (i. e., the devices must alarm at a distance of 10 feet from the power line).

Jan 1, 1980

By David Schlain

IN 1942 the Bureau of Mines began to develop the Kroll process for use in the large-scale production of titanium. Titanium and titanium alloys are now commercial metals. These metals are relatively expensive, but It is now evident that they will have important industrial uses and that in many instances these will be related to their remarkable corrosion resistance. This bulletin presents the known corrosion properties of titanium and its alloys in useful form. In marine environments titanium is highly resistant to corrosion and does not pit, or undergo crevice corrosion, stress corrosion, or corrosion fatigue. Titanium is also highly resistant in many salt solutions, including most chlorides. It is very resistant to corrosion in nitric acid solutions. It is also resistant to white fuming nitric acid. However, it may react violently with red fuming nitric acid. In phosphoric acid solutions titanium has rela¬tively good resistance to corrosion, but it has less resistance to sulfuric acid and still less to hydrochloric acid solutions. Titanium corrodes very rapidly in hydrofluoric acid Solutions. It is very resistant to corrosion in many organic chemicals. However, it has only moderate resistance to formic acid solutions and poor resistance inn oxalic acid solutions. Titanium does not corrode in dichloroaretic acid but, corrodes rapidly in 100 percent trichloroacetic acid at 100° C. Titanium is resistant to barium, calcium, magnesium, ammonium, and sodium hydroxides. Titanium is inert in wet chlorine, bromine, or iodine gases. However, in dry chlorine gas titanium reacts rapidly enough to ignite. It also reacts rapidly with dry bromine gas, but, it is resistant to dry iodine gas. When titanium is exposed to red fuming nitric acid solutions with high nitrogen dioxide content and low water content, it corrodes, undergoes stress-corrosion cracking, and becomes pyrophoric. This occurs more readily with some titanium alleys, such as titanium-8 percent manganese. A fresh titanium surface immersed in water or in an aqueous solution and in contact with an oxygen-rich atmosphere under sufficientt pressure is unstable and will ignite spontaneously. Inherently an active metal, titanium has a tendency to become less active in environments containing oxidizing agents such as air, oxygen, chlorine, or ferric, cupric, or platinic ions. Titanium is more noble than most structural metals in roost, environments and its excellent corrosion resistance is generally not, affected by contact with these metals. However, some of the other metals corrode faster because of contact with titanium. Titanium undergoes anodic polarization readily, so that even when it is the less noble member of a galvanic couple it may corrode less because of the contact. Titanium alloys often have corrosion properties and electrochemical characteristics similar to those of commercially pure titanium. Titanium alloys containing noble metals, zirconium, molybdenum, vanadium, tantalum, or copper sometimes have better corrosion resistance than pure titanium.

Jan 1, 1964

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By Jr. Hazen

Two statistical techniques, the mean-square-successive-difference test and correlation, are used to investigate the problem of assigning an area of influence to an assay. Data from five hydrothermal deposits, Climax molybdenum, Cebolla Creek titaniferous iron, San Manuel copper, Piedra Hueca copper, and Butte copper, are studied. Two groupings of the assays are used for the mean-square-successive-difference tests. One group involves an increasing sample volume by reaveraging assays to represent a longer sample intervals, the other by regrouping assays to represent longer sample intervals without a change in sample volume.

Jan 1, 1967

By W. R. Reed, J. A. Organiscak

Surface mining operations use large off-road haul trucks extensively to move material at mining properties. Past research, using the United States Environmental Protection Agency’s (EPA) emissions factors for unpaved haul roads, has shown that haul trucks generate the majority of dust emissions from surface mining sites, accounting for approximately 78%-97% of total dust emissions. Observations of dust emissions from haul trucks show that if the dust emissions are uncontrolled, they can be a safety hazard by impairing the operator’s visibility. This increases the probability for haul truck accidents (See photos above). However, the greatest long-term health hazard of dust generated from hauling operations is due to inhalation of the respirable dust [median diameter <4 micrometers (µm)] and tho­racic dust, which is equivalent to the EPA’s definition of PM10 [particulate matter with a median diameter <10 µm]. Exposure to respirable dust has long been considered a health hazard at surface mining operations, especially if silica dust is present. There are two legislative acts that regulate the air quality for mining operations: the Federal Coal Mine Health and Safety Act of 1969 and the Clean Air Act of 1970. The Federal Coal Mine Health and Safety Act of 1969 established the limits for dust in the work place for health and safety pur­poses. The Clean Air Act of 1970 regulates air emissions from facilities from an envi­ronmental perspective.

By Harry F. Weaver

Rivers in industrial and raining areas frequently are contaminated by material dumped into them causing the water to carry in suspension large amounts of silt, which subsequently is deposited alone; the banks and, ultimately on the agricultural lands if the water is used for irrigation purposes. Two common examples of this practice are the dumping of breaker refuse in the anthracite region of Pennsylvania and the dumping of tailings from the metallurgical mills in various metal-mining districts. Studies in stream pollution and its resultant problems are very important, and surveys are constantly being made by Federal and State agencies, as well as by private companies, to determine the quantity of solids actually being carried by these watercoarses. These studies require accurate sampling of the silt-carrying water to determine the amount of solids within reasonable limits. A device that will obtain reasonably accurate samples of material from silt-bearing streams is described in this circular.

Jan 1, 1943

By A. E. Sands

The Bureau of Mines, S. Department of the Interior) at, its Morgantown., W. Va., station, operating under a cooperative agreement with West Virginia University, is conducting research and development work on the problem of producing synthesis gas from coal. An important part of this work is the study of the gas purification necessary to meet the rigorous standards required to render the gas suitable for use in the Fischer-Tropsch synthesis of liquid fuels. One of the most detrimental impurities is sulfur in all forms, the maximum amount that can be tolerated being one-tenth of a grain per hundred cubic feet. Concentrations as low as this require the use of precise analytical methods to evaluate the performance of processes used for removing sulfur. At the same time the analytical methods should be rapid in order to reveal the failure of purification before damage to the expensive synthesis catalyst results. Although sulfur in unpurified gas is generally present as hydrogen sulfide and as organic sulfur compounds, the latter may be converted to hydrogen sulfide for analytical purposes. Thus a suitable method for the determination of traces of hydrogen sulfide may also be used for the determination of organic sulfur.

Jan 1, 1949