Search Documents

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By L. A. Neumeier

The Bureau of Mines investigated hot-rolling and forging characteristics of experimental ductile iron castings, both sand and permanent-mold, made with charges containing up to 70 pct foundry pig iron and 95 pct steelmaking pig iron. Between 1,550° and 1,950° F, most castings could be rolled to 90-pct reduction or forged to 70-pct reduction without serious cracking. Charge and composition have less bearing on workability than on subsequent properties. Permanent mold castings could be worked as readily as sand castings at 1,750° and 1,950° F. Plasticity improved with temperature. Small billets were also forged cold to 50-pct reduction without cracking. With equivalent nodularity, composition affects properties of wrought materials by altering matrix structure and strength. Properties vary with reduction and improve with increasing working temperature. Rolled material has high strength and anisotropy, and low ductility, particularly in the trans-verse direction. Annealing reduces strength and improves ductility, but anisotropy persists. At 70-pct reduction, impact resistance in the longitudinal direction is about twice that in the transverse. Annealing roughly doubles impact resistance. Deformation enhances damping capacity. The feasibility of die-forging and bar-rolling of ductile iron was evaluated in trial tests conducted under a Bureau contract. Although workability and ductility of ductile iron are inferior to those of steel, more advantage could be taken of ductile iron's plasticity to work rough shapes to final dimensions.

Jan 1, 1980

By K. K. Kelley

The first bulletin (245)3 in this series, which appeared in 1932, summarized the entropy values then available for the elements and inorganic compounds, results being listed for some 150 substances. In the interim advances in the realms of spectroscopy applicable to the determination of thermodynamic properties and in the development of methods of calculation therefrom have added many highly accurate values. Moreover, through the efforts of Prof. W. M. Latimer (286) and his coworkers, satisfactory entropy values are now available for all but a few of the common inorganic ions in aqueous solution. At the same time rapid progress has continued in the study of low-temperature heat capacities in several laboratories, In addition, compilation and correlation of data pertaining to vapor pressures (247), thermodynamic properties of carbonates (258), thermodynamic properties of sulfur and its inorganic compounds (250), and the thermodynamic properties of metal carbides and nitrides (251), which were published as members of this series, have yielded many values. As a result, over 500 usable entropy values for inorganic substances may now be tabulated. This bulletin originally was planned as a second revision of the first member of this series, the first revision (249) having appeared in 1936; however, because of requests for the explanatory section of the first bulletin from those teaching thermodynamics, it was decided to com¬bine the information in the first bulletin and its revision with the data that have appeared since 1935 and to repeat the explanatory material in somewhat more detail. The purpose of this bulletin is therefore to give the available values of the entropies at 298.1° K. of the elements and inorganic compounds, together with enough explanation of the methods employed in calculating entropies to make the results comprehensible.

Jan 1, 1941

By H. P. Hamlin, W. A. Grosh

Samples of clays , shales , and argillites from 21 locations were subjected to preliminary bench- scale tests for bloating properties , and several samples were tested for ceramic properties . Samples showing favorable bloating properties were further tested in a pilot - plant - scale rotary kiln . Physical characteristics and concrete -making properties of the bloated products were determined . The Decorah shale from one area made a suitable material for a lightweight aggregate ; however , the limestone layers in the formation must be eliminated or the resulting activated lime must be controlled by quenching .

Jan 1, 1963

By Martin A. Elliott

The Bureau of Mines began its investigation of the use of Diesel engines underground to provide technical information necessary to assist this development in the United States. It was considered desirable to furnish such assistance because successful European developments/ in this. field had indicated that Diesel mine locomotives might be safer than electric trolley locomotives. The Bureau has recognized for some time the importance of eliminating the hazards associated with underground haulage systems using bare trolley wires. For example, each year 30 to 40 fatalities occur as a result of electrocution by contact with bare trolley wires. In 1943 and 1944, 101 men were killed and extensive property damage occurred as a result of mine fires started by falls of roof grounding the bare trolley wires.

Jan 1, 1948

By James J. Scott

Workshops were held in eight states during the period from December 12. 1975. through June 25, 1976, under U. S. Bureau of Mines Contract to the University of Missouri-Rolla. The workshops were designed to help define the Bureau's research and development priorities. At each workshop a summary of the current Bureau mine reclamation research was presented which was followed by identification of problems associated with mine land reclamation in the state where the meeting was being held. Discussions included the seriousness of problems locally and how the Bureau could best undertake research to assist the state in solving the problems identified. Participants included representatives of state agencies, educational institutions, and companies involved in surface mining. Attendance at these workshops totaled 201 persons who displayed a wide variety of opinions and ideas as to what should be done In government research and development efforts. A breakdown of these attendees is as follows: 91 state and Federal employees; 69 mine operators, equipment manufacturers and consultants; 33 educators and researchers; and 8 others representing such varied interests as environmental and conservation groups, news media and students .

Jan 1, 1976

By Leon E. Esparza

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 16,927-acre Pryor Mountain Wilderness Study Area (MT-067-206), part of the 3,955-acre Burnt Timber Canyon Wilderness Study Area (MT-067-205), and part of the 4,550-acre Big Horn Tack-On Wilderness Study Area (MT-067-207) to evaluate their identified mineral resources. The Burnt Timber and Big Horn Tack-On study areas contain 3,430 and 2,550 acres, respectively. The three areas are in Carbon County, MT, and Big Horn County, WY, about 13 miles north of Lovell, WY. No identified resources exist in any of the study areas. Bureau of Mines personnel reviewed literature, searched county mining records and examined prospects, claims, and mineralized areas to determine whether identified mineral resources existed. The three study areas are within the Pryor Mountain unorganized mining district. U.S. Department of Energy production records indicate there were 223,000 pounds of uranium oxide (U308) and 236,000 pounds of vanadium pentoxide (V205) produced from 19 properties within the mining district. The average ore grade was 0.36 percent [3,600 ppm (parts per million)] U308 and 0.416 percent (4,160 ppm) V20S. Only the Pryor Mountain study area has current claims, the 50 claims of the S0S group.

Jan 1, 1986

By N. F. LeJeune, Earl C. Lane

This is the third of a series of reports on a survey of petroleum prod- ucts manufactured on the Pacific Coast from California crude oils. California crudes differ in many characteristics from the petroleum produced in the other parts of the United States, and the claim has been made that some of the present Federal Specifications for petroleum products tend to discriminate against Cali- fomia products. The purposes of the present survey are to determine what par- ticular specification requirements Califomia petroleum products characteristical ly fail to meet, how widely the products deviate from these requirements, and if possible to show whether the fault lies with the specifications or the products, or along what lines investigation to determine this question should proceed. The first report of the series gave the physical and chemical properties of the samples of gasoline and mineral spirits. A second report**, gave the physical and chemical properties of samples of lubricating oils. The present report deals entirely with burning and fuel oils. The refin ing companies have continued their very cordial and helpful cooperation. Seven samples of kerosene, four samples of Diesel fuel and eight samples of fuel oil were obtained. The methods of analysis used are those adopted by the Interdepartmental Petroleum Specifications Committee, published by the Bureau of Mines in Technical Paper No. 323. The specifications used for corparison are those officially adopted by the Federal Specifications Board for the use of the various Depart- ments and Independent Establishments of the Government, effective February 3, 1923, and published by the Bureau of Mines in Technical Paper No. 323, Part 1. Specific gravity, degrees A.P.I., viscosity and other special tests al- though not required by the specifications have been given for comparison. All temperatures are recorded in degrees Fahrenheit. Tables have been prepared giving data on physical and chemical propertios of the individual samples. Before each table the classification and specifica- tions for the particular class of oil considered in the table are given. Follow- ing each table, brief notes show wherein samples deviate from specification re- quirements.

Aug 1, 1923

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casing-heads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil. into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casingheads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By D. W. Blaylock

I. The Lower Kittaning bed is the most important bed in Clarion County from the standpoint of present production, but the Clarion bed has the largest recoverable reserve. 2. Known measured and indicated reserves in all beds, based on a minim thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 1,210 million short tons as of January 1, 1952. Of this total, 790 million short tons is in beds 28 inches and mare thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too wager for ding an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, they should be added to the total estimated reserves.

Jan 1, 1956

By Wilbert J. Huff

For the past 9 years , the technical studies conducted by the Explosives Division of this Bureau have been summarized in a series of reports issued annually . The following account presents investigations undertaken from July 1 , 1943 , to June 30 , 1944. The work is detailed under a number of main headings corresponding to the organizational structure of the Division , the various activities being under the immediate direction of unit chiefs , who report directly to the author . Specific credit , however , is due to the individual unit leader and his assistants .

Jan 1, 1945

By R. L. Loofbourow

The adjacent towns of Rouyn and Noranda, centers of the Rouyn mining district of western Quebec, are 360 miles by air line almost duo north of Toronto. Rouyn is reached from the main lines of the Canadian National Railways and the Canadian Pacific Railway at North Bay, Ontario, by the Temiskaming & Northern Ontario Railway and its subsidiary, the Nipissing Central Railway. Noranda is the southwestern terminus of a branch from the Canadian National Railway between Winnipeg and Quebec. The Rouyn mining district is a part of a mineralized zone that has been traced for a distance of 140 miles from Kirkland Lake in Ontario eastward into the Province of Quebec to the Pascalis district. From Rouyn the mine is 5 miler almost duo south over a gravel rend built by the company with assistance from the Province of Quebec.

Jan 1, 1933

By S. B. Levin

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. During the fall of 1942, the Bureau of Mines put down nine diamond-drill holes at the Cape Rosier zinc-copper-lead mine in Hancock County, Maine, that aggregated 2,883 feet of bore. These holes supplemented 13 holes, aggregating. 5,501 feet, put down on the property about 2 years earlier by the St. Joseph Lead Co. Veins of mixed sulfides were intersected in 15 of the holes drilled. Beneficiation tests were made on samples of ore obtained from old dumps. Zinc-copper-lead sulfides occur at the Cape Rosier mine as lenses in a zone of altered agglomerate beneath and between a series of diorite sills. The mineralized zone strikes F. 17° E. and dips southeast. Between July 1881 and September 1883 the mine produced about 10,000 tons of ore reported to have contained 20 percent zinc, 2.8 percent copper, and some lead. The crude ore was hand-sorted, and some. 3,000 tons were reported shipped.

Jan 1, 1948

By Joseph Grumer

About a century ago Bunsen and his associates invented the famous burner that bears his name and was to become the ancestor of today's gas appliances. Over the years, Bunsen's invention became the starting point of a highly developed, practical technology that culminated in the gas industry as we now know it. However, it did not occur to the early workers to investigate the scientific potentialities of the new device, and as a result the science of gas-burner performance did not keep pace with the growing industry. It was with the objective of closing the rapidly widening gap between science and technology that the present research was undertaken Its immediate purpose was to provide basic information on the combustion characteristics of .fuel gases, in particular as they affect flashback, blowoff, and yellow tipping. Information obtained in the present research and contained within this report consists of the following: (1) Fundamental flashback and blowoff characteristics have been determined, it is believed, for all fuel-gas mixtures in which the gas industry may be interested. These are critical boundary velocity gradients for flames in free air, on burners with ports at room temperature and pressure. Burner aeration is characterized by the parameter, fraction of stoichiometric. These basic limits are explained, values are presented, and calculation procedure is given for deriving corresponding values of port loading and percent primary air (chs. I and II).

Jan 1, 1956

By R. V. Ramani

"Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of 'mines according to the best recommended practices, (3) medical control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health deterioration:-The respirable contaminants in mine atmo¬spheres are toxic and explosive gases, toxic and explosive dusts, diesel exhaust particu¬lates, radon progeny, etc. Perhaps the most important of all these and the most widely occurring in mine atmospheres is respirable dust, an inevitable product of fragmentation, a unit operation fundamental to all mining operations. In fact; the-most serious health hazard for workers in the mining and minerals processing industries is still the exposure to respirable dust, and solutions to the problem of respirable dust disease remain to be found.The 1969 Coal Mine Health and Safety Act and its provisions for the respirable dust standards in underground coal mines are briefly reviewed. An overview of the research accomplishments in meeting the standards is presented. The current state of knowledge on the effectiveness of the standards and the new and emerging problems are discussed. A brief summary of the research programs of the Generic Technology Center on Respirable Dust is presented.In general, underground mines are becoming increasingly safe. The mine atmospheric environment is definitely improving * Professor and Head, Department of Mineral Engineering,-The Pennsylvania State University, University Park, PA for the better. Significant progress has been made in lowering the dust levels in mines. It is generally agreed that mines are less dusty today than they were a decade ago. However, as long as the risks of occupation-related diseases are not completely eliminated, vigilance can hardly be relaxed, and the search for engineering solutions must be intensified."

Jan 1, 1988

By E. J. (Kirk) Conway

Thirty-five years ago underground coal mining equipment consisted of simple but rugged machines powered by electric motors and hydraulics. The machines were maintained by maintenance personnel armed with a basic knowledge of hydraulics, electricity, and mechanical design. Over the years the the machine has been transformed into powerful complex mining systems. The maintenance burden has also increased. During this period significant advances have been made in maintainability engineering and system design techniques. Many of these innovations and techniques are applicable to the design of underground mining equipment. The objectives of this project were to; (1) determine the extent to which maintainability design concepts and principles have been applied to the design of underground coal mining equipment, (2) try to assess the impact of equipment design for maintenance on productivity and safety, and (3) develop a maintainability design guideline to enhance the design of new or rebuilt equipment. An equipment design review was completed at ten operational coal mines. Interviews were also conducted with mine management, safety, and maintenance personnel to identify machine specific design advantages and problems. Visits were also made to six original equipment manufacturers to discuss the design of their equipment for maintenance. Volume I presents an overview of the protocol used and a summary of the findings. Volume II includes the maintainability design guide for underground mobile mining equipment.

Jan 1, 1989

By George Markon

The importance of United States coal exports as a component of the national economy, the potential for growth of these exports, and the inter-national character of this sector of the coal industry are described in this report. The report summarizes some of the many background elements in the rise of United States coals to preeminence in highly competitive world markets. It presents some insight into this important sector of United States industry and the positive contribution of this sector to the Nation's balance of payments. It contains pertinent basic statistics on production, trade, and consumption of coal in most major markets for 1960-66. The report examines the movement of United States coals from mines to export markets, tracing and describing origins, exit ports, prices, and trends as well as inland and ocean freight rates and other data vital to an under-standing of some of the practices and complexities of the United States coal markets abroad. A brief sketch of coal production and consumption in principal importing countries is also presented with a short review of some of the more current practices and problems of these countries. Coal produced in inland areas of the. United States can be moved to and distributed economically within coal-producing countries overseas and in Canada. Quality coals from the United States can successfully compete with foreign coals in nearly any area of the world on a truly economic basis because of their high grade and their low cost which derives from the high productivity of the miner and from reasonable ocean freight rates. Because of tariffs, trade embargoes, quotas, and other restrictions, how-I ever, foreign coal markets are relatively limited. Further limitations are imposed in some countries by economic conditions which restrict all imports as a matter of financial and economic necessity. Despite these obstacles, United States coals have brought lower cost quality coals to a large segment of the foreign energy market.

Jan 1, 1968

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the' Bureau of Mines since 1917. The analysis published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966