Search Documents

By Benjamin W. Haynes

Cement kiln dust (CKD) produced in the contiguous United States and Hawaii was characterized as part of the Bureau of Mines' program in minerals environmental technology. The mineralogical and chemical composition was determined for 113 CKD samples from 102 plants that normally send CKD waste to landfill. Characterization included the determination of 28 elements, 7 anion species, carbon dioxide, noncarbonate carbon, and chemically bound water. Mercury was determined in 15 samples. Interelement correlation coefficients were determined for 23 elements, 5 anions, CO2, noncarbonate carbon, and chemically bound water. To assess the hazardous waste potential of CKD, the U.S. Environmental Protection Agency Extraction Procedure (EP) toxicity test was performed on all 113 CKD samples. All but one sample were in compliance with the test; the noncomplying sample slightly exceeded the EP toxicity test criterion for lead.

Jan 1, 1982

By L. G. Marshall

This report, describing the mining method of the Dresser Trap Rock Co., Dresser, Wis., is one of a series published by the Bureau of Mines on mining methods, performance, and costs at mining operations throughout the United States. SUMMARY Dresser, in Polk County, is 3 miles south of St. Croix Falls, Wis. Company operations are about 1 mile north of the townsite. The mine has been in [peration] since 1914 and under the present ownership since 1949.

Jan 1, 1959

By V. E. Homme, M. M. Wong

Tests were made in reactors ranging from 12 to 30 inches in diameter to develop methods for the preparation of sodium chloride - titanium lower chlorides ( dichloride and trichloride ) melts that contain titanium predominantly in the divalent state . Such melts are desirable as a starting material for the production of titanium metal or as an electrolyte for electrorefining of titanium . Sodium reduction of TiCl with an 18 - hour period of holding the reaction products in the molten state produced melts that contained titanium lower chlorides in TiCl₂ - to - TiCl , molar ratio of approximately 8 to 1. Sodium reduction of TiCl in a reactor with a shielded pipe weir , that required no melt -holding period , produced melts with a TiCl₂ - toTiCl , molar ratio as low as 4 to 1 . Reduction of TiCl4 with scrap titanium metal in molten sodium chloride produced relatively pure melts containing about 27 percent titanium in a Ticl₂ - to - Ticl , molar ratio of approximately 4 to 1 .

Jan 1, 1964

By D. W. Bridges, Donald R. Peterson, Masami Hayashi

Techniques are described for recovering about 80 pct of the cobalt and nickel contained in superalloy scrap by anodic dissolution of the scrap and simultaneous electrodeposition of a pure cobalt - nickel alloy at the cathodes in an electrolytic cell partitioned by permeable diaphragms into separate anode and cathode compartments . Superalloy scrap was alternatively prepared for subsequent anodic dissolution either by melting and casting massive scrap into suitably sized anodes , by packing moderate - sized discard scrap in inert metal baskets that subsequently served as anodes , or after concentrating the superalloy portion of grinding debris , by magnetic separation to reject corundum or other abrasives , slagging any remaining abrasives from molten grindings , and finally casting the superalloy metal into anodes . In the processing , purified electrolyte -- 1 N in NiSO4 and in NiCl₂ , and 0.1 N in CoSO4 and in CoCl2 --was charged to the cathode compartments and discharged from the anode compartments at a rate sufficient to overcome the backward migration of ionic impurities from the anodes to the cathodes . Discharged electrolyte was purified by reacting it first with SO2 and next with limestone , and then recirculated to the cathode compartments , in which a 50 pct cobalt - 50 pct nickel alloy was deposited on either blanks of stainless steel or starting sheets of cobalt - nickel alloy . The process was made self - sustaining by either adding H2SO4 to the catholyte feed to throttle the rate of cobalt - nickel deposition , thereby compensating for the slower rate of cobalt - nickel dissolution from the anode and losses occurring in electrolyte purification , or alternatively , adding H₂SO4 to

Jan 1, 1964

By Fred Kissell

The Bureau of Mines has developed the shearer-clearer--a new type of dust control system for longwall shearers. The system partitions the airflow around the shearer into a clean split and a contaminated split. The dust cloud is confined to the vicinity of the coal face, while the shearer operators remain in the clean split on the gob side of the machine. The shearer-clearer operates on the principle that each water spray moves air like a small fan and can be positioned to direct the dusty air towards the face. The hardware is inexpensive and can be installed in a single shift. It consists of several strategically mounted water sprays and one or more passive barriers. Laboratory testing indicates reductions 1n shearer operator dust exposure as high as 97 pct. Preliminary results from an underground demonstration in one mine also indicate that considerable dust reductions at the shearer may be obtained. In conjunction with the development of the shearer-clearer, dust surveys were conducted in three other mines to determine if some shearer spray systems currently in use partition the flow in a manner similar to the shearer-clearer, and if so, whether this partially accounts for markedly cleaner conditions on some longwalls. Results from these surveys indicate this to be the case. A feature of the cleaner longwalls was a downwind orientation of their water sprays, which is a key element of the shearer-clearer system. The shearer-clearer system described in this report was designed for an Eickhoff EDW 300 shearer working a 7-foot coal seam. The testing to date has concentrated on cutting directions counter to the primary airflow. The development effort continues for different mining equipment and conditions. It is expected that different systems will be required to accommodate the range of conditions occurring underground. Application of the system presented here to conditions different than those described is not likely to produce the same results.

Jan 1, 1981

By Lester M. Adams

In 1980, the Bureau of Mines surveyed a group of mine seals in Randolph County, WV, to evaluate their effectiveness for reducing toxic pollutants in mine water discharges. The survey focused on 11 block wet mine seals, but mine seals of several other types were also examined. The seals were installed in 1966 and 1967 in abandoned drift portals by the Federal Water Quality Administration (FWQA), a predecessor of the Environmental Protection Agency (EPA), in cooperation with the Bureau of Mines and other Federal and State agencies, in a project known as Elkins Mine Drainage Pollution Control Demonstration Project. The seals were designed to prevent air from entering the mine portals while allowing mine water to flow out. It was believed that by preventing air from entering inactive or abandoned mines, the formation of toxic pollutants and acid mine drainage (AMD) could be reduced. Evaluation of the seals was based on water flow measurements, water analyses, and visual observations. The Bureau's 1980 data were compared with past data collected by the EPA. Several leaks and failures were observed in the clay seals, as evidenced by apparent blowouts and the absence of vegetation where the mine water surfaced. Analyses of the 1980 data indicated some improvement in the quality of water discharged from many of the wet air seals.

Jan 1, 1984

By W. W. Adams, T. D. Lawrence

"The National Safety Competition conducted by the Bureau of Mines, United States Department of the Interior for the promotion of safety in mines and quarries, has just been closed for seventeenth consecutive year. Enrollment covered more plants than in any previous contest. Moreover, a larger volume of employment was represented than in the contests of previous years, and several new plants were enrolled for the first time. Six safety trophies are awarded annually in these competitions one to the leading plant in each of six groups. An anthracite, mine in Pennsylvania, a bituminous-coal mine in West Virginia, a metal mine in Tennessee, a nonmetal mine in Virginia an open-cut mine in Minnesota, and a quarry in Alabama won the 1941 trophies.To be eligible to win a trophy, a mine or quarry must have had at least least 25 men working under ground or in the pit for not loss than 100 days. The number of man-hours worked must total 30,000 or more. Mines or quarries having no accidents during the year are rated according to the number of man-hours worked. If there are no plants with accident-free records, the mines and quarries in each of the six groups are rated according to their accident-severity rates; the plant having, the lowest rate is declared the winner.The Sentinls of safety trophies presented to the winning mines and quarries in the six groups were donated by the Explosives Engineer magazine to promote safety in the mineral industry. They are held by the winning companies for 1 year or until won by other mines and quarries."

Jul 1, 1942

By R. A. Egen

The purpose of this book is to provide an indication of what good hoisting practice is and how it might be achieved. To this end the book contains discussions of equipment and inspection and maintenance procedures developed and used by mining people in striving for safe, reliable hoisting equipment. Most of this information comes from domestic practice; the rest is foreign, notably from Canada. Most things discussed have long proved their general worth, and others promise to; a few are beginnings. However, nothing is conjectural or theoretical; the practices described herein are in use somewhere in the mining world. The stress is on equipment in use; it is not a design-guidelines manual. Nevertheless, there are some sections dealing with design material since it may be of value in a maintenance/ replacement sense. Mine hoisting installations encompass such a wide variety of equipment and conditions that it is impractical to specifically cover them all. This book mainly treats conventional systems using conventional components with some discussion of the more common unconventional (special) systems in use. There is no recognized definition for a "conventional" mine-hoisting system. Herein the term means those systems most commonly used in daily operations for transporting men, materials, and product-electrically driven drum and friction hoists, with guided conveyances running in vertical or inclined shafts. Beyond this, what "conventional" means is probably best illustrated by the topics discussed.

Jan 1, 1975

By John Ward Smith

The Bureau of Mines derived equations expressing the theoretical relationship between density of oil-shale rock and its organic content. Effects on theoretical shale density produced by variations in mineral composition and organic matter properties were evaluated. The theoretical relationship was extended to relate oil-shale density to oil yield in both oil weight and volume units by considering the fraction of organic matter converted to oil and the specific gravity of the oil produced. Corollary equations relating organic content by volume to organic content by weight and to oil yield were developed. The general relationships apply to an oil-shale deposit uniform in character. Application of the theoretical relationships to Green River Formation oil shales was demonstrated.

Jan 1, 1969

By Harley A. Coy

This paper, describing the mining methods and practice at No. 2 mine of the American Zino Co. of Tennessee at Mascot, Tenn., is one of a series of papers issued by the Bureau of Mines presenting the mining methods and costs in various districts throughout the United States. Its purpose is to summarize methods recently put into practice whereby increased efficiency has been effected. These improvements have to do principally with mill-hole mining, slushing, contract labor, and bonuses. In general, this paper supplements earlier articles and brings them up to date. ACKNOWLEDGMENTS The author acknowledges the assistance of M. H. Newman, geologist of the American Zinc, Lead & Smelting Co.; of William Black, assistant superintendent of mines; of P. M. Arthur, director of personnel; and of the engineering staff. The paper has been approved by H. I. Young, vice president and manager of operations.

Jan 1, 1930

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By Nunna Malakondaiah

Plant samples collected from the mined sites of Beulah, Center and Zap and the test sites of North Beulah 1, North Beulah If, South Beulahh and Center were analyzed for their nutrient concentrations. The vegetation from the mined areas generally showed lower concentrations of Na, P and Cu and failed to meet the nutritional requirements for beef cattle as defined by National Research Council (minimum requirements are: Na, 600; Cu, 4; P, 1800 µg/g dry weight). Plants from Beulah showed generally higher concentrations than from Center or Tap. Tissue concentrations of K varied significantly between sites for 5 species due to the low tissue concentrations at Center. Deficiencies are difficult to isolate as the sampling was done in mid-summer and generally during that season the tissue concentrations tend to decrease in several species. All of the plant species at the unmined sites, with the exception of western wheatgrass at Zap, had lower concentrations of P than the minimum nutritional requirements for beef cattle. Sodium concentration was low but Cu was marginal to adequate in plant species at the unmined sites. Concentrations of K, Mn and Cu in western wheatgrass were greater at Center than at Zap while the opposite was true of the concentrations of Zn, Cu and P in blue grama and Cu in green needlegrass. Amending the spoil with slack at North Beulah I decreased the concentrations of Zn, Cu and P in wheatgrasses grown on spoil from 0-2, 5-10, and 20-25 foot depths, respectively. In general, the mean tissue K+/Na+ ratios were greater in plants on slack amended spoils, primarily due to the reduced Na concentrations in the tissue. At North Beulah II test site, only wheatgrasses grown on spoil amended with slack showed significant increase in K and decrease in Na and Mn concentrations. At South Beulah test site which received 12" topsoil over graded spoil, leonardite amendment decreased P concentrations in all of the grasses as compared to control, whereas fertilizer treatment increased the same. Nutrient concentrations were lower in both fescue and needlegrass with leonardite treatment and higher with fertilizer treatment although not significantly different from control. The concentrations of Ca, Mg, Na, Fe, Cu and N in grasses grown on topsoil at Center test site were significantly higher than on slack amended spoil. Legumes grown on topsoil at Center site contained higher concentrations of P than those grown on spoil; there were no significant effects due to slack on spoil or topsoil. The data presented in this report act only as an indication of between-treatment and between-species differences in tissue composition of plants harvested in mid-summer season. With respect to the nutrients analyzed, since none were found to be toxic, the cattle can safely feed on the vegetation of these mined areas.

Jan 1, 1982

By Carl F. Wingquist

In support of Bureau of Mines studies of thermal fragmentation of rock, the elastic moduli of four types of rock were measured at temperatures ranging from room temperature up to 1,500° F (1,089° K). The sonic method was employed to determine the resonant frequencies of the rock specimens and from these frequencies, the elastic moduli were calculated. Data for Young's modulus, shear modulus, and Poisson's ratio are given as a function of temperature for Dresser basalt, Reserve taconite, Jasper quartzite, and Charcoal granite. Young's modulus and the shear modulus decreased with increasing temperature up to about 1,200° F and then became relatively insensitive to temperatures from 1,200° to 1,500° F.

Jan 1, 1969

By R. E. Heithecker

The principle of determining volumes of liquid by alternately drawing in and discharging given quantities of the fluid from a confined space or compartment of known volume and mechanically counting the number of displacements is well established. This is true particularly in water measurement. For several years, oil meters employing the same basic principle have beer used for gaging oil production from individual wells, groups of wells, and in some areas for metering the entire production from a property. Especially in areas where there is town-lot drilling and space for tankage is at a premium, oil meters have been used successfully to gale the oil. This facility has obviated the necessity of installing gage tanks. Oil meters also have been used in pipe-line and refinery operations and in loading tankers. Present knowledge e of the subject shows that positive-displacement oil meters can be used for measuring crude oil in the field and elsewhere, provided the meter-counter mechanism is in proper adjustment and the oil has been studied sufficiently to determine the pro-per factor to be applied to the volume as registered by tae meter, possible the adjustment for the shrinkage of the oil caused by liberation of gas from solution.

Jan 1, 1938

By Arthur V. Petty

The Bureau of Mines has investigated the effect of refractory oxide additions, introduced in soluble form, on the refractory properties of 42-, 58-, and 70-pct-A1203 brick. Brick having porosities ranging from 12 to 16 pct were impregnated with solutions containing chrome, chrome-iron, zirconium, calcium, magnesium, cobalt, nickel, tin, and manganese ions. Additions of some of these ions provided dramatic improvements to such properties as hot modulus of rupture, hot load, and particularly slag resistance. These improvements can be related to reduction of porosity, amorphous grain boundary phases, formation of more refractory bond phases, and reduction of the wettability of Al203-containing refractories by metallurgical slags. Fifty-eight-percent-AI203 brick, impregnated with chrome, showed hot modulus of rupture, hot load, and slag resistance two to five times better than those of untreated 70-pct-AI203 brick. This could result in reducing the Nation's dependence on imported refractory-grade bauxite generally required for high-A1203 brick, as domestic alumina resouces could be used to produce the improved refractories.

Jan 1, 1984

By R. D. Leitch

Beside many other damaging effects of acid mine drainage, corrosion of pipe lines and pumps frequently adds much to mine operating, costs. Not only is it often necessary to install special and relatively costly acid-resistant materials, but even these may require frequent replacements. It is not unusual for ordinary steel pipe to last only a few days in some highly acid waters, while other common materials, though more resistant, frequently cast only a few weeks. In the spring of 1935, local PWA authorities offered to assign a number of persons to various problems under the direction of regular employees of the Bureau of Mines. It was believed that at least some simple tests on as many different kinds of acid-resistant pipes as could readily be obtained might produce interesting; and valuable information for the mining industry. This paper describes the tests and some results that have since been noted.

Jan 1, 1938

By L. D. Schmidt, H. G. Graham

Several processes for the production of ultra-clean coal for electrode carbon were developed in Germany prior to and during World War II . These processes have been investigated since the end of the war by the British and U. S. Government missions . As the reports of the investigations are not readily available to the public , it is the purpose of this paper to present the information which has been obtained regarding the methods by which ultraclean coal was produced . Almost all the ultra-clean coal was used in the manufacture of electrodes for the production of aluminum and magnesium . Standard raw materials for making these electrodes are pitch coke and petroleum coke , which are nearly ashless . The inclusion of ash in the electrode carbon results in lowered efficiency and impure metal from the reduction process . Petroleum coke and pitch coke were in very short supply in Germany during the war , so that it was necessary to augment the supply with carbon produced from coal . In the emergency , methods were developed to clean coal which had never before been economically feasible . However , a demand for nearly ash-free coal might develop in the United States if a shortage of petroleum coke were to occur at the same time as a strong demand for light metals . Other uses of ultraclean coal are in direct hydrogenation of coal , in production of activated carbon, and for special fuels . Specifications for electrode carbon are rather severe owing to the necessity for producing pure metal . Maximum amounts of impurities allowable in American practice are as follows : Total ash , 1.0 percent ( in finished coke , 0.7 percent ) Silica , 0.08 percent Ca or Na, or their sum , 0.12 percent Sulfur , 2.0 percent Ba , Ni , Cr , Mn , Co , and V are objectionable in very small amounts . The most important process for ultra cleaning of coal in Germany was froth flotation . Froth flotation had been used widely there to process washery -water sludges and to recover coking coal from high - ash fines . Its use was indicated , therefore , when the demand for ultra low-ash coal arose . In two plants the coal cleaned by froth flotation was treated with acid or caustic to lower further the ash content . Another process used on an industrial scale was that of dissolving the coal substance in the middle oil from direct hydrogenation of coal under controlled pressure and temperature . The resulting paste was heated, filtered , and the oil distilled off . The residue was a low-ash organic material that could be carbonized for electrode carbon or could be hydrogenated directly . Several other processes had been developed to the laboratory or pilot - plant stage but had never been used on a commercial scale . These processes included cleaning by centrifugal action , cleaning by electrostatic action , and cleaning by forming a paste with oil in water . The coal-preparation plants at the Carl Alexander mine , Augusta Viktoria mine , and Kőenigin Elisabeth mine are described in Bureau of Mines Information Circular 7389 : " Coal Preparation Practice in Western Germany" , by Thomas . Fraser and M. G. Driessen . Most of the special equipment used at these plants is described in the above publication .

Oct 1, 1948

By Louis C. Brichta

This report summarizes the progress made by the Federal Bureau of Mines in assembling and compiling a catalog of available logs of drill holes and maps of mine developments in the Tri-State Zinc-Lead District in northeastern Oklahoma, southeastern Kansas, and southwestern Missouri. It supplements an interim report (11)3/ published in 1955, and for convenience of the reader repeats much of the general descriptive matter pertinent to the district contained in that report. The work of procuring and recording the data was begun in August 1949 and was recessed in May 1959. The catalog preserves the records of accomplished explorations and mine developments in the district and provides a readily available source of information for individuals and firms interested in planning mineral explorations, Government agencies estimating of reserves of mineral resources, and the mining industry for general use.

Jan 1, 1960

By Wallace W. Roepke

The Bureau of Mines tested new designs of drag bit cutters with sintered diamond inserts instead of standard tungsten carbide tips. The bits were tested for orthogonal cutting forces, primary dust generation, and incendivity, with a standard plumb-bob type conical cutter (600 included tip angle) as the reference. Preliminary wear and impact-failure testing were also done. The results were mixed. Two new designs had forces similar to those of the reference bit, but one new design had about twice the normal force. This same design had almost twice the specific energy during shallow cutting but generated an equal or slightly lower amount of primary dust than did the reference bit. Incendivity was eliminated for two radial designs. One conical design had ignition only after more than 15 impacts, but the other conical design was incendive. Impact failure occurred, but not so quickly as anticipated. Over 7,500 impacts on a sandstone face, with a total cutting distance of more than 1,981.2 m, only scuffed the leading edge of the sintered diamond cutting face but put hairline cracks in the substrate mounting pad. Additional design and testing are needed to develop an optimum cutter, but prospects look good for this material.

Jan 1, 1983

By Ricardo Burdisso, Rahul Kadam, Kyle Schwartz, Marty Johnson

Occupational exposure to hand transmitted vibration (HTV) arises from the hand held powered tools extensively used in the mining and construction industry such as rock drills, chipping hammers, chain saws etc. Regular exposure to HTV is the major cause of a range of permanent injuries to human hands and arms which are commonly referred to as hand-arm vibration syndrome (HAVS). In addition to this, the percussive tools generate overall sound power levels in excess of 110dBA in most cases. Such a high sound power level greatly exceeds the maximum permissible exposure limit (PEL) of organizations such as National Institute for Occupational Safety and Health (NIOSH) and the Occupational Safety and Health Administration (OSHA). Long term occupational exposure to this noise has been diagnosed as the main reason for permanent hearing loss in the operators. It is therefore important to develop an understanding of the mechanisms which lead to these high vibration and sound levels and in order to do this a detailed computational model of a pneumatic chipping hammer has been made. This paper presents a nonlinear computational model of a pneumatic chipping hammer. In order to better understand the dynamics of the chipping hammer, the hammer was subdivided into components that are shown in figure 1 (a) (based on a chipping hammer manufactured by Atlas-Copco). The hammer mainly consisted of a center body, a moving piston and a chisel. Compressed air is used to drive the piston inside of a cylinder and on the downward stroke this piston impacts the chisel to create the hammer effect. The machine has one pneumatic valve and this valve regulates the air supply either to the upper chamber or to the lower chamber. The valve changes according to the relative pressures in the two chambers and the supply pressure. There are also twelve different exhaust ports at two positions along the cylinder labeled upper ports and lower ports. As the piston moves the ports can be closed or open (allowing exhaust). Fundamentally, the computational model was made up of two different sub-models, a fluid model and a structural dynamic model as shown in Figure 3 (a) and (b) respectively. The first sub-model takes into consideration the fluid dynamics of the machine since the hammer is driven by compressed air. Equations for the mass flow rate though bleed orifices (assuming an isentropic process) 1 is used to determine the mass flow into and out of the upper and lower chambers. From this the pressures in the two chambers and consequently the forcing on the piston can be calculated. The second sub-model deals with modeling the structural [ ]

Jan 6, 2006