Search Documents

By R. J. Morrell

The Bureau of Mines conducted a series of laboratory experiments to test a cutting technique for hard rock using large-scale drag cutters. Cutting experiments were performed on rocks ranging in compressive strength from 10,000 to 27,000 Ib/in2, using large drag cutters from 3 to 6 in. in width. The tests were conducted on a special test apparatus, called a ripper tester, which made a curvilinear cut across the rock sample while measuring the cutting force acting on the drag cutter. The cutting method that evolved from these experiments is called ripper cutting, and its energy efficiency appears superior to all other large-scale mechanical fragmentation techniques. In addition, the method cre-ated very little dust, and the wear on the bits was negligible. A fragmentation system based on ripper cutting was then devised, and a large-scale test device was fabricated to allow full-scale laboratory testing of the system. The results of these tests will be published in future Bureau reports.

Jan 1, 1986

By Dwight L. Sawyer, Roy T. Sorensen

The Bureau of Mines has investigated the recovery of alumina by hydrochloric acid leaching of calcined kaolinitic clay . Bench- scale studies indicated that horizontal belt filtration was a pprraaccttiiccaall method for separating the siliceous residue from aluminum chloride liquor generated in the leaching step . Miniplant -scale continuous testing was performed to evaluate the filter circuits and to compare filtration response of different calcined kaolin feed materials and of different agitatorbaffle designs in the leaching reactors . Soluble alumina recovery with a single filter ranged from 94 pct with minus 10 -mesh feed more than 96 pct with minus 35-mesh or misted feed . Process advantages were confirmed for the calcined misted kaolin feed material prepared by a Bureau-developed misting process . With two filters in series , an overall filtration rate of 100 lb solids /hr.ft - 2 of filter area was attained with a soluble alumina recovery of more than 99 pct . More than 99.5 pct alumina recovery was obtained with a thickener and a two - filter circuit for either the minus 35-mesh or the misted feed . Modifications in leaching reactor design made to decrease particle- toparticle attrition were successful and significantly increased filtration rates and decreased flocculant requirements .

Jan 1, 1965

By N. A. C. Smith, A. C. Fieldner, R. R. Sayers

Gases and vapors given off by petroleum and its products have long been recognized as somewhat injurious, when inhaled in high enough concentrations. The petroleum industry has recognized these effects and has tried to minimize the possibility of employees encountering dangerous concentrations of the vapors. Petroleum gases and vapors have not, however, been considered as actively poisonous, in the sense that hydrocyanic (prussic) acid and phosgene are poisonous; men have been exposed to them repeatedly, and for long periods, without any marked ill effects. Light Mexican crude oil when first introduced into the United States for refining was handled in much the same way as was customary with other apparently similar crudes; but experience soon showed that some toxic substance escaped from the crude during production and transportation and in most of the refinery operations. After a preliminary investigation several of the larger companies decided that the gases from the petroleum were the source of trouble, and therefore took precautions, wherever possible, to protect the men from exposure to these gases. With the increasing use of Mexican crude, this problem has become important. The present report covers the work done on the subject by the Bureau of Mines and the Public Health Service under a cooperative agreement with the American Petroleum Institute.

Jan 1, 1925

By Arden D. Fugate

The Federal Bureau of Mines conducted extensive studies on solid-state defluorination (laboratory scale) and tests on molten defluorination (intermediate scale) of siliceous fluorspars. The studies were made to develop a pyrohydrolytic process for liberating fluorine from offgrade fluorspars. Test results showed that more than 90 percent of the fluorine can be evolved by solid-state defluorination at 1,300° C., and more than 97 percent can be liberated by molten-state defluorination at 1,420° C. Solid-state defluorination conditions were established by conducting tests on mixtures of ceramic-grade fluorspars and high-purity silica flour. Pelletized mixtures were defluorinated under varying conditions of time, temperature, and relative concentrations of silica, calcium fluoride, and water. The effects of adding various amounts and combinations of aluminum oxide and iron oxide on defluorination were also studied. Investigations of solid-state defluorination indicates that the following two reactions are involved: 2CaF2 + 3SiO2 = 2CaSiO3 + SiF4, and CaF2 + Sio2 + H20 = CaSiO3 + 2HF, The second reaction is dominant, although significant defluorination can be achieved by the first reaction.

Jan 1, 1961

This volume constitutes the Survival Subsystem portion of the final report for the Coal Mine Rescue and Survival System (CMR&SS) program, which was conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated June 17, 1970). The program was directed by the Special Systems Department of the Westinghouse Baltimore, Maryland, facility. The basic objectives of the CMR&SS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major sources: the Request for Proposal from the Bureau of Mines1 and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering2 (NAE).

Jan 1, 1971

By R. W. Stahl

A survey of firefighting facilities and practices in coal mines conducted by the Bureau of Mines3/ showed such variations in equipment and apparent attitude toward fire protection that a comparison with other industry seemed advisable. Although other industry is confined generally to surface operations and the hazards probably are not as great, the same general methods of extinguishment are employed, so that the cost and protection at least should be comparable. An investigation of industry other than mines revealed a generally greater emphasis placed on fire-combating equipment, fire-brigade training, fire-fighting facility inspection, and fire-hazard elimination, as well as a greater average expenditure for fire protection.

Jan 1, 1959

By J. F. Barkley

During the present war emergency, under the urge of the Federal Government to store coal, the following questions are frequently asked by coal users: (a) Will the coal lose any, of its heating value in storage? (b) Will it slack and give a smaller-size coal? (c) Will its burning characteristics change in any way? (d) Will it catch fire from spontaneous combustion? (e) What precautions should be taken when coal is stored? DISCUSSION (a) Loss of Heating Value Studies by the Bureau of Mines show that the loss of heating value of coal in storage commonly has been overestimated. Various types of storage tests were made on New River, Pocahontas, Pittsburgh gas, and Sheridan (Wyo.) coals. The following is quoted from Bureau of Mines Bulletin 136, Deterioration in the Heating Value of Coal During Storage, by H. C. Porter and F. K. Ovitz (p. 8):

Jan 1, 1943

By A. Matzick

In its work under the Synthetic Liquid Fuels Program the Bureau of Mines has developed on a 6-ton-a-day-pilot-plant scale a continuous, gravity-feed retort far distilling oil from oil shale. The development work covered by this report was done from January 27, 1950, to January 26, 1952, at the ail-Shale Experiment Station near Rifle, Colo. Over 300 pilot-plant tests were made during the investigation. The basic retort developed has been named the Gas-Combustion retort. In this process, part of the heat for retorting of the shale is generated by burning recycled product gas in a combustion zone within the descending shale bad in the retort. Additional heat is supplied by combustion of the carbonaceous residue remaining in the spent shale after the oil has been distilled. Air for combustion is admitted through an air distributor in the center of the bed at about the mid-point of the retort. Hot gas rising from the combustion zone heats countercurrently the descending raw shale and liberated shale oil by pyrolysis of the shale. After passing through and exchanging heat with the incoming raw shale, the oil is condensed as a fog or mist in the gas, which is withdrawn at the tip of the retort. The cool gas is then piped to an oil-recovery system where the oil is separated from the gas in centrifugal separators or other types of mechanical or electrostatic separators. The hot, spent shale below the combustion zone is cooled by heat exchange with recycle gas, which is a portion of the effluent gas from the oil-recovery system.

Jan 1, 1955

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

By J. R. Thoenen

This circular is part 3 of the third paper (entitled "Excavation") of a series summarizing the technical problem; involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes. Fart 2 discussed the use of power scrapers, slackline cableway excavators, and hydraulic monitors. This circular discusses the use of the hydraulic, clamshell, ladder, and dipper dredge. Part 4 to follow will discus the use of haulage equipment, and subsequent parts will discuss the application of both excavating and haulage equipment to various types of deposits. HYDRAULIC DREDGE Judged by the number of installations and the tonnage produced, as recorded in part 1 of this circular, the hydraulic or pump dredge is the most popular type of underwater sand and gravel excavator.

Jan 1, 1935

By G. B. Gait

This report is the fourth in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of 70 mines in the Western Middle field is presented. Previous reports were catalogs of microfilmed maps of mines in the Eastern Middle field and in the Wyoming and Lackawanna Basins of the Northern anthracite field. Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1971

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields and rapid depletion of existing reserves emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry to meet increasing market demands, but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields" Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most of the operations are of the pressure-maintenance type} in which the reservoir pressure is maintained or partly maintained by injecting natural gas to increase oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes gas and water-injection projects in California.

Jan 1, 1952

By R. S. Dean

The work of the metallurgical fundamentals section during the past year, representing active experimental investigation or thermodynamic study, may be summarized as the following problem subjects: 1. Low-temperature specific-heat investigations. 2. Development of a method of concentrating gases. 3. Thermodynamic properties of metallic carbides and nitrides, 4. Production of pure chromium from chromium chlorides. 5. Thermodynamic properties of the hydrates of calcium, sulphate. While this list is not identical, with officially designated problems, due to overlapping of subjects and to new developments within specified problems, presentation upon the basis of this subdivision will best serve to review the work of the section.

Jan 1, 1937

By Kung-Lee Wang

This report describes the linkage of all mining sectors with all other manufacturing, services, and final demand sectors of the U.S. economy. Besides being a basic data source, it provides a framework for aggregate economic impact analysis with respect to the mining industries. The framework is an open-static input-output model specifying 48 mining industries as classified in the Standard Industrial Classification Manual for all mining activities and 76 nonmining industries which collectively exhaust, all economic activities. The 124-sector model used in this report is an expansion of the preliminary 82-industry aggregation estimates made by the Department of Commerce. In the expanded model, 48 ruining industries are substituted for the original 6. The methodology used to ascertain the industry-by-industry procurement cost estimates and product ion flows necessary to the construction and expansion of the basic 82-sector model included personal interviews, case studies of specific mining activity analysis, and published and unpublished data from the Bureau of Mines and the Census of Mineral Industries, The end products of this study are two tables arranged to show the direct purchases necessary for each industry to support the level of economic activity and the total purchases generated in each industry throughout the economy by each $1 of aggregate economic demand in 1958. The tables may he used for economic impact studies and market analysis by firms engaged in or closely associated with the mining industries. Some illustrations of their usages are presented.

Jan 1, 1967

By W. J. Kroll

This investigation was undertaken with the idea of studying a number of unconventional methods for making chromium to determine whether production cost could be lowered and to discuss some of the more recently described processes. These comprise carbon reduction of the oxide in vacuum, nitride dissociation, fusion electrolysis of the chloride, amalgam method, iodide dissociation, calcium reduction of the oxide, hydrogen reduction of the chloride, and reduction of this compound with zinc and with magnesium. Preference is given this latter method, which is shown in a flow sheet. Special attention is given purification of the chloride and separation of the vacuum at about 900° C. A reduction method for the elimination of traces of oxide contained in pure chromium by pure hydrogen obtained from the dissociation of zirconium hydride is described. The various methods are compared in a table in the appendix. Aluminothermic and silicothermic methods for the reduction of chromium oxide and the aqueous electrolysis have been disregarded in this investigation.

Jan 1, 1950

By R. V. Higgins

"INTRODUCTION When nations throughout the world are pitted against each other in a war in which petroleum plays a major role, scientist and engineers of the petroleum industry must give serious thought to ways and means for recover¬ing greater percentages of oil from natural reservoirs than in the past. Petroleum and its products are vital to highly mechanized modern warfare, and the victorious nations will be those whose armies, navies, and air forces are supplied with adequate fuel oil, gasoline, and lubricants until the war is won.Efficient recovery of oil from underground reservoirs depends on many interrelated techniques; evaluation of the producing performance of wells upon the basis of their productivity indexes is one such tool. Oil wells usually yield oil at a maximum rate when first ""brought in"". The rate of production begins to decline soon after the first oil is delivered to the tanks, and although part of the decline usually can be attributed to natural reduction of reservoir pressure as oil and as are withdrawn from the reservoir, a larger proportion frequently is caused by greater saturation of water and as in the producing formation about wells and clogging of the pores of the sands by silt, organic salt, and insoluble hydrocarbons. If the maximum quantity of oil is to be recovered from reservoir sands and rocks by wells, it is then imperative that the ability of wells to produce oil be watched closely and all adverse influences that affect the case with which oil can flow to wells be corrected if possible."

Sep 1, 1942

By J. F. Barkley

Two major problems in the operation of air preheaters for boilers are corrosion and the accumulation of deposits on the heating surfaces. Corrosion or loss of metal necessitates replacement of parts; the accumulation of deposits decreases the size of the gas and air passages, resulting in increased pressure drop for the same gas flow, and also affects the heat transfer. These items, either singly or together, limit the capacity and efficiency at which the equipment can be operated and affect its availability, even causing undesirable shutdowns under extreme conditions The field and laboratory work on regenerative air preheaters described in this report covers research on the relative corrosion resistance of different materials, such as various metals, special metal coverings, and fired clays, and studies on deposits, their nature, analyses, and corrosive effects. This is the first report on cooperative work of The Air Preheater Corp., of New York City, and the Federal Bureau of Mines.

Jan 1, 1953

By R. A. V. Raff

Although falls of roof, face and rib (or side) of coal mines were the third ranking cause of disabling accidents in 1966, the accidents from these falls resulted in the most serious injuries and accounted for approximately 50 percent of the total fatalities (I). Further breakdown of these statistics shows that 88 percent of the fatal accidents occurred within 100 feet of the working face and that 96 percent of the deaths were in bituminous mines, with only four percent taking place in anthracite workings. These figures demonstrated the need for improved reinforcement procedures in operational coal mines, and they provided ample justification for research in the area of accident prevention. The purpose of this project was to investigate the use of polymers and of related techniques to achieve rock bonding and reinforcement of coal mine structures, in order to obtain better or permanent ground support (e.g., drifts, entrees, coal and ore passes, galleries, tunnels and shafts) by the fill ing of fissures in the rock, thereby preventing or delaying the onset of serious rock degradation processes.

Jan 1, 1973

By Potts J. D.

Installation of a horizontal air-blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong Coand? effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector-to-bailing-airflow ratio and a 51-mm (2-in.) gap between the shroud and ground. The shelf was 152-mm (6-in.) wide and was located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air-blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2008

By K. J. Miller

Electrophoretic mobility measurements of coal and pyrite particles in distilled water revealed a difference between the migration speeds of the two materials toward the anode in a dc electric field. This information led to the development of a laboratory electrophoresis column for separating fine pyrite from coal by utilizing the electrokinetic and the specific gravity differences between coal and pyrite. The study demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis using a stage separation technique. In a cost analysis, electrical power for electrophoresis was extrapolated to about $1 per ton of clean coal product. But, since the only successful tests ever made were in the laboratory with prewashed samples of minus 100-plus 325-mesh coal in distilled water, the cost figure derived is not representative of conditions prevalent in commercial coal cleaning operations. True conditions would reflect costs many times as great. In the course of the work, several scale-up techniques were considered but their feasibility became academic in view of the physical and economic problems associated with electrophoretic separation of pyrite from coal. Although the process and apparatus were finally deemed impractical for commercial coal preparation, the electrophoresis column may have some application as a laboratory device.

Jan 1, 1974