Search Documents

By George S. Rice, C. W. Owings

"Brattice cloth is an important material in coal-mine ventilation practically all coal mines use some brattice cloth, gassy mines a large amount. It is employed in three ways:Crosscut brattices.Curtains in haulageways.Line brattices in gassy mines.In each case brattice cloth is used to deflect part or all of a split of the mine ventilating current into or toward the face of a working place. As a general rule, its use in a particular location is temporary.A crosscut brattice should be employed only until a permanent stopping has been erected. Such a brattice is subject to little wear when in actual service, the chief damage occurring when it is taken down and put up again.When used for curtains on haulageways or haulage crosscuts to deflect the air current up into rooms or headings, the wear on brattice cloth is considerable, as mine cars, machines, and personnel constantly pass under the curtains which last only a few days or a few weeks in an active part of the mine. For such purposes tightly woven smooth cloth is desirable, so that it will not be easily torn. Curtains should not be used back from the working places, as they sometimes are, to deflect the main. split, as the leakage of air is too great. Doors should be used in such places."

May 1, 1928

By J. S. Webb

This is one of a series of papers dealing with mining methods, practice, and costs be¬ing published by the United States Bureau of Mires. In this paper a description of the mining practice in vogue at the Braden unit of the Kennecott Copper Corporation is undertaken. PRODUCTION At present (1931) the entire production of ore is being obtained from the Teniente mine. The miring method in use is an adaptation of block undercutting which has been a development of the stoping and pillar caving experience obtained at this property. Improvements in mining practice are constantly being made.

Jan 1, 1932

By L. L. NAUS, R. D. Currie

Hazards in connection with the use of compressed-air jets for ventilating gassy mines are given little consideration by most mine officials largely because compressed air is considered the safest means of transmitting power for operating various types of mining machinery, and the inherent dangers in its use for this purpose are virtually negligible . The installation of compressed-air lines in coal mines leads to the utilization of compressed air for ventilating working places , with the result that , although the primary ventilation systems may be adequate to meet existing needs , proper conduction of normal ventilation has been neglected , so the working faces receive only a small amount ofthe total air circulated through the mine . Reliance in part on compressed air or other auxiliary means for ventilation is always attended by danger that gas will accumulate , due to intermittent operation , and the tendency is to operate auxiliary schemes only. during the working shift ( or possibly only part of the shift ) and to dispense with them during off- shifts or at times during the working shift when gas may accumulate because of lack of ventilation . When the men come on shift the auxiliary ventilating device often may be started without a preliminary examination of the working place , or .. the examination may be made sometime before the oncoming shift arrives , the gas being allowed to accumulate in the meantime. This may result in uncontrolled movement of a body of gas if proper precautions are not taken . Several mine explosions have been caused by the movement of a known body of gas by compressed air into the haulageway, where it was ignited by an arc from a passing locomotive . This danger is more pronounced where supervision is lax .

Aug 1, 1937

By William R. Wayment, David E. Nicholson

A modified percolation - rate test is proposed for use in determining flow rates through hydraulic backfill ; in contrast to the conventional test , a percolation- rate versus void - ratio relationship is established . requirements and a detailed test procedure are described . Equipment Results of a conventional test are compared with those of the proposed modified test . The proposed modified test method yields more accurate , realistic , and usable percolation- rate ( permeability ) data . The significance of obtaining accurate percolation rates for use in analyzing waterflow through hydraulic backfill is discussed .

Jan 1, 1964

By Eugene Fry

The Huber-Rydalch manganese property is in the Erickson mining district of Tooele County, Utah. The district covers the southern part of Simpson Mountains, a block rising abruptly above the surrounding desert floor (fig. 1). The Ruber-Rydalch deposits and other deposits in the Simpson Mountains manganese area were examined by Bureau of Mines engineers during 1940 and 1942 under the strategic minerals program. J. T. Pardee visited the district briefly in 1918. A. E. Granger and A. F. Shride, of the Federal Geological Survey, mapped the geology of the area in 1942 and 1943. The manganese deposits occur as veinlike masses in brecciated fault zones that traverse Cambrian and pre-Cambrian quartzite, quartzite conglomerate, and phyllite. The deposits now exposed near the surface represent the oxidized portions of primary mineralization originally containing rhodochrosite and rhodonite associated with quartz and calcite and small quantities of pyrite, galena, sphalerite, and chalcopyrite. The oxide ore is composed of manganite, pyrolusite, psilomelans, and wad in a gangue of quartz, calcite, and brecciated quartzite.

Jan 1, 1949

By Scott Turner

Within recent years , people have begun to realize the importance and significance of the mining and allied industries . The leading part the engineer plays in civilization is becoming recognized . However , accurate quantitative knowledge of the industrial importance of mining is still seldom possessed except by those close to this business . It is true that there are a few who go to the extreme and represent the whole progress of civilization as a reflection of man's gradual mastery of mineral utilization , but on the whole , the magnitude of the industry is underestimated . The uncertainties of mining , as evidenced by the variable results of prospecting on surface or underground , in an unknown new field or from the bottom levels of a mature mine , the ins and outs of tonnages and metal contents , the possibility of a widespread or even a sudden change between cost and realization-price , add to its picturesqueness and make mining attractive to some . To many , the fact that results are generally more uncertain and less predictable than in other industries lends added charm . The following pages may serve to call attention briefly to the importance of mining relative to other industries in the United States , in Canada , and in the world . Ordinarily , the annual primary mineral production of the United States amounts to about 5 billion dollars . The average for the last five years has been a little over 5 billion dollars . Last year , sadly enough , it was less than 34 billions . Just now , we are on the decline , and have been for the past two years . In Canada , the 5-year average was about 268 million dollars . Last year it was 227 million . Due in part to gold output ( in 1930 , for the first time , Canada's gold production exceeded that of the United States ) , the Canadian average is holding up better than ours . It has been estimated that the average world mineral production over the past five years has amounted to about 12 billion dollars , while in 1931 it was less than 8 billions . The mineral industries are as indispensable for the conduct of modern society as are those of agriculture , but , in the United States at least , they receive far less recognition from the Government . With us , agriculture is fostered by a great department that is maintained by enormous appropriations , while the mineral industries get but little financial support . In the United States , in the calendar year 1930 , the value of production by these two industries were as follows : to 1 . Agriculture ( inclusive of forestry ) 9.9 billion dollars ; mining 4.8 billions ; ratio 2 Direct appropriations by our Federal Government were 109 million dollars to agriculture and 2.8 million to mining , a ratio of 39 to 1. Obviously this is out of balance to the extent of 19 to 1 in favor of agriculture .

Jun 1, 1932

By A. A. Bakewell

This information circular, which describes mining methods and practices at the Baguio Gold Mining Co., Philippine Islands, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs. Since January 1952, Baguio Gold Mining Co. has operated its rehabilitated mine and mill in the Baguio district. Postwar labor and supply costs are three or four times prewar costs, whereas ore tenor and tonnage are about the same. Ore reserves remain approximately the same, but deeper and more spreadout operations add to increasing costs. Recently the company has acquired an adjoining property, which may lengthen its life substantially. Costs and general operations are more or less typical of the district, which includes three other active gold mines. Gold ore mined in the district totals approximately 4,300 tons per day.

Jan 1, 1959

[CONTENTS COUNTY NO. OF MINES MINE INDEX PAGE]

Jan 1, 1980

By K. E. Stanfield

[Asphalt and road oil are the principal products manufactured from Wyoming ?clack oils? which, because of their high asphalt an high sulfur content, are difficult and costly to refine into high-grade motor fuels, burning oils, and lubricants by pre sent methods. Accordingly, the remand for these asphaltic residuums for the construction of roads and other uses is a controlling- factor in the quantity of crude oil produced. The increasing utilization of special asphalts as inexpensive bonding, insulating, and waterproofing materials indicates the desirability of obtaining information on the yield and properties, of asphalts from Wyoming black oil to promote a wider and more stable caret for these asphaltic materials.]

Jan 1, 1941

By Jr .. Ebbley

The investigation of mine shafts and underground workings at Leadville, Colo., was started in May 1946 and recessed in November 3, 1946. Thirty-eight shafts and connecting accessible underground workings, comprising about a third of the accessible shafts in the district, were investigated. The Leadville district, a former important producer of lead and zinc, was considered by the Bureau of Mines to be capable of bolstering 'the waning domestic output of .these important metal. Accordingly, the investigation was initiated for the purpose of. .obtaining more definite data on sulfide and oxide reserves, evidence to justify completion of the Leadville drainage tunnel, representative large samples of the complex oxidized and mixed ores for testing to determine methods, beneficiation factual data to be supplied to property owners in order to stimulate production, and to determine the more favorable areas for development by the Bureau.

Jan 1, 1949

By J. H. East, D. Harrington

"INTRODUCTION Mining at its best is not a clean occupation for either surface or underground employees; and this applies alike to coal, metal, and non-metallic mines. The employees are handling minerals that have been blasted, or broken by some means and are subjected to mineral dust, whether it is coal, quartz, or talc. The employees usually wear clothes specifically adapted to the work in which they are engaged, and frequently these clothes are not suitable for use away from the mine. Many mines are wet, and employees must wear rubber boots to remain at least partly dry, and even on relatively dry mines, some parts of the mines usually have water falling from overhead, there are accumulations of water, or the floor or other surfaces are wet or muddy, Some mines are dusty, and the air-borne dust quickly settles on the clothes and body of the miner, especially, when he is working in confined areas, or in places that are hot, humid, or poorly ventilated. Most occupations around a coal tipple, anthracite breaker, or a mill at a metal or nonmetallic mine have their own problems of cleanliness as to skin or clothes or both. Mining in any of its phases is inherently dirty work, and the employees dress accordingly while at work.In the early stages of mining it was the custom or workers to wear their dirty clothes home and change there. This necessitated their going home after work in dirty clothes which were usually damp from perspiration or from contact with wet or muddy matelials or surfaces, and, in addition to being inconvenient this was a frequent cause of colds, pneumonia, other pulmonary diseases or, possible skin ailments. Men working in very wet mines found that it was more satisfactory to change into dry clothes in the boiler room at the mine after work and allow their wet clothes to dry overnight. The mining companies later provided the first of the so-called ""dry-houses"" which were heated but had, few, if any, conveniences, such as showers, lockers, or latrines. The miners changed into dry clothes after work, but would not bathe or ""clean up"" until they reached their homes. Later, progressive mining companies provided bathing facilities for the employees, and eventually the present modern wash and change houses were evolved. Unfortunately, many mines, still have no bathing accommodations, and many have only makeshift accommodations."

Dec 1, 1947

By H. E. Perlee

Autoignition temperatures and limits of flammability of nine halogenated hydrocarbons in atmospheres of air, oxygen, and nitrogen tetroxide were measured in a modified standard autoignition apparatus and limit-of-flammability apparatus previously developed at the Bureau of Nines. Of the nine halogenated hydrocarbons investigates--bromochloromethane, bromotrifluoromethane, bromochlorodifluoromethane, 1,1,2-trichlorotrifluoroethane, 1-bromo-l-chloro-2,2,2-trifluoroethane, dibromodifluoromethane, l,2-dibromo-1,1,2,2-tetrafluoro-ethane, 1,1,1,3,3-pentachlorotrifluoropropane, and l-bromo-2,4-dichloro-1,1,2, 3,3,4-hexafluorobutane--two formed flammable mixtures with nitrogen tetroxide and six with oxygen; none formed flammable mixtures with air. Three of the halogenated hydrocarbons formed no flammable zones with any of the three oxidizing atmospheres. For those halogenated hydrocarbons that supported combustion in oxygen atmospheres, explosion pressures developed during constant-volume burning of mixtures near the middle of the flammable zone were observed to range from about 6 psig for dibromodifluoromethane to 158 psig for 1-bromo-1-chloro-2,2,2-trifluoroethane. In all cases, the calculated burning velocities of these mixtures were less than 8 in/sec.

Jan 1, 1966

By F. J. Wiebel

"INTRODUCTION As a result of a general survey of the iron-ore deposits of Califor¬nia, the Bessemer was one shown to offer possibilities of developing com¬mercial ore reserves. Surveying and exploring were done at the request of Congress for an investigation of raw materials for the production of steel.A wartime steel plant has been established at Fontana, San Bernardino County, and a backlog of iron-ore reserve for the maintenance of permanent steel industry on the West Coast will be of National benefit in the postwar period.W. D. McMillan, a mining engineer the Bureau of Mines, examined the property in May 1942, and it was reexamined by D. W. Butner, also of the Bureau, in October 1943. Geophysical work was done by the Bureau in 1944, and the property was explored by diamond drilling from April to August 1944 and February to SeptemberACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, under the direction of R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

May 1, 1947

By John R. Troxell

"INTRODUCTION The Ahles iron mine, also known as the Pequest mine, in Warren County, N. J., was operated continuously for 15 years and was still in ore when it closed in 1916.Tie property was examined by an engineer of the Bureau of Mines in March 1943. 3/ This examination led to an investigation of the deposits by the Bureau by diamond drilling two holes under the old workings to determine whether the extends downward.This report describes the work done at the Ahles mine by the Bureau and presents the data obtained.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report.The Metallurgical Division, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The investigation was under the general supervision of J. B. Zadra, acting regional engineer, and under the immediate supervision of G. D. Jermain, district engineer for the States of Pennsylvania, New Jersey, Maryland, and Delaware. The author was in direct charge of the project.The chemical analyses for the project were performed at the College, Park, Md., laboratories of the Bureau of Mines under the direction of M. S. Sheftel. The ore-dressing tests were conducted at College Park under the direction of Frank Lamb. Preston E. Hotz, of the Federal Geological Survey, logged and interpreted the drill cores."

Apr 1, 1948

By J. J. Cummins

The Bureau of Mines heated at 150° to 350° C for 0.5 to 360. days Green River oil shale that had been previously extracted by benzene to provide information on in situ processing conditions, to determine the effect of low-temperature heating on the unconverted kerogen, and to determine the composition of benzene-soluble thermal products. The methods used in determining the composition of the soluble thermal products consisted of fractionation of the soluble material, elemental analysis of the soluble products, fractionation of the polar resins by ion-exchange chromatography, gas chromatographic analysis of [n]-alkanes3 and mass spectral analysis of the branched plus cyclic alkanes and aromatic oils. The methods used to determine the effect of low-temperature heating on the unconverted kerogen remaining in the oil shale heated residues consisted of carbon-hydrogen analysis, volatile material determination, carbon residue determination, and oxidation rate determination. In general, it was concluded that significant increases in the degradation of kerogen to oil occurred between the temperature range of 250° to 350° C; that the composition of the soluble products depends upon the temperature at which they are formed; and that the [n]-alkanes are pyrolytically degraded from the kerogen structure. In particular, the 250° C heating temperature is beneficial to the formation of branched plus cyclic alkanes. Also, the heated and unconverted oil shale kerogen and the soluble thermal products become more aromatic as the temperature increases from 150° to 350° C.

Jan 1, 1974

By Kenneth L. Rubow, Virgil A. Marple, Zhigun Zhang

"A theoretical technique has been developed and verified experimentally for determining the aerodynamic diameter of irregular shaped particles. The aerodynamic diameter of a particle is a very important parameter for determining where that particle deposits in the respiratory tract. Many instruments, such as impactors and cyclones, will determine the aerodynamic size distributions of aerosol particles but few analyze the particles individually. The theoretical approach of our technique is to solve, by use of high speed computers, the three-dimensional Navier-Stokes equations to obtain the flow field around an irregular shaped particle of any contour. The computer program will then determine the drag on the particle, and thus the aerodynamic diameter of the particle can be calculated. The experimental approach has been to pass the particles through a centrifuge and collect the particles upon a collection foil. The position of a particle on the foil is an indication of its aerodynamic diameter. These particles were then shadowed in two orthogonal directions and inspected under an scanning electron microscope (SEM). The top view of the particle in the SEM plus the views of the two orthogonal shadows allows one to determine the three-dimensional shape of the particle. Studies have been performed on silica, coal and talc particles with aerodynamic diameters in the 1 to 4 µm size range. The three-dimensional shape, as is determined from SEM analysis, was used in the theoretical computer program and the results compared. It was found that in most cases the agreement between the experimentally and theoretically determined aerodynamic diameters was within 5%. INTRODCJCTIONThe equivalent aerodynamic diameter (EAD) of a particle, defined as the diameter of a unit density sphere with the same falling speed as the particle in question, is an important size measurement of the particle. This is especially true when attempting to predict where particles may deposit in the respirator tract. Therefore, EAD is an important parameter when considering respiratory diseases caused by particles, such as coal workers pneumoconiosis (CWP).Many instruments will measure the EAD size distribution of the aerosol particles, but few analyze the particles individually. Impactors, cyclones and virtual impactors normally collect particles upon substrates or filters which are · then analyzed gravimetrically to determine the mass concentration of the particles in that size classification. The EAD of particles can be measured on an individual basis with centrifuges, inertial spectrometers and the TSI Aerodynamic Particle Sizer (APS). Centrifuges are most ideally applicable for studying individual particles as the particles are deposited, on long removable foils, at locations dependent upon their EAD."

Jan 1, 1990

By Robert B. McElwaine

"The demand for barite has increased greatly in the last 10 years, especially during World War II. Depletion of oil reserves and subsequent increase in deep drilling created a heavy demand by the oil industry for barite to be used as drilling mud. The great increase in demand for barite gave impetus to the development of a, deposit of impure barite near, Magnet Cove in Hot Spring County, Ark.The critical condition of the national barite supply early in 1944 led the War Production Board to recommend that the Bureau of Mines attempt to prove the existence of a large reserve tonnage of barite in the Magnet Cove area and arch for new deposits. To carry out this program, the Bureau explored on newly reported. Barite deposits in southern Montgomery County, Ark. The Gap Mountain, Fancy Hill, and Sulphur Mountain barite deposits were investigated. Eight diamond core-drill holes and 1,336 linear feet of surface trenching were completed, and barite samples obtained were analyzed, A study of the Montgomery County barnse district indicates that the lenticular bodies of barite replace a favorable host rock near the base of the Stanley shale formation. Barite is exposed along the side of anticlinal mountains where erosion has truncated the beds on the limbs of the associated synclines. An appreciable amount of barite suitable for commercial use has been indicated by trenching and core drilling. The Gap Mountain and Fancy Hill deposits are controlled by the Magnet Cove Barium Corp. and Baroid Sales Division of National Load Co., respectively. The ore is similar to that of the Magnet Cove area and is amenable to concentration by a flotation process. Mining of these deposits had not been begun by the time the Bureau completed its exploration project."

Nov 1, 1946

By R. L. Marovelli

ANTICIPATING the eventual use of the huge tonnages of nonmagnetic taconites of the Mesabi range of the United States, the Federal Bureau of Mines is classifying and evaluating these deposits in detail. This introductory report describes work begun in 1954 as part of a long-range program to sample, classify, and evaluate important occurrences of nonmagnetic taconite on the Mesabi, range. Included in this report are brief discussions of the geology, history, and potential of the Mesabi range district and mining industry, together with a more detailed presentation of the sampling and metallurgical evaluation of these nonmagnetic taconite deposits. A total of 898 field samples was collected. Most of these were taken in the region between Grand Rapids and Chisholm, Minn., but a few came from the area between Chisholm and Buhl, Minn. Of the total samples, 865 were from open pit bank faces where the greater vertical distances presented by the cherty members facilitated the taking of a large number of samples. Conversely, the narrow face presented by the slaty members confined and limited the areas from which samples were taken. In addition, 33 of the field samples were taken from rock dumps in order to determine, in a preliminary way, the characteristics of these materials.

Jan 1, 1961

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

By V. F. Parry

The major industrial uses of char or semicoke produced by low-temperature carbonization of coal4/ are as fuel for generating electric power, for blending with metallurgical coking coal as a substitute for low-volatile coals, and for gasification to produce synthesis gas for chemical purposes. This paper discusses various methods for carbonizing coal, emphasizing processing of the noncoking coals to produce char for thermal power-plant fuel and for blending with metallurgical coking coals and tar for chemical use. Low-temperature carbonization is a relatively simple processing step involving heating coal to about 900° to 1,200° F. to decompose the coal into 4 main products: (1) Semicoke or char; (2) complex, partly oxygenated liquid hydrocarbons or tar; (3) fixed gases; and (4) water. If the coal is heated rapidly under conditions that prevent decomposition of the primary products, 68 to 87 percent of the net heat in the raw coal is left in the char and 10 to 23 percent of the potential heat appears in the primary tar. Fixed gases represent approximately 7 percent of the heat and approximately 2 percent is lost or dissipated in the reactions of decomposition. Considering the different ranks of coal in the United States, the yield of tar will vary from about 9 to 44 gallons per ton, therefore it is important that each coal be carefully considered if it is to be carbonized for industrial use.

Jan 1, 1955