Search Documents

By Larry A. Haas

The Bureau of Mines is investigating the use of complex gas mixtures, such as would be produced by coal gasification, for reducing iron oxide pellets. A semiempirical model was developed to predict a priori the reduction rate of an iron oxide pellet in a laboratory tube furnace with simulated coal gases at a total pressure of 1 atm. The model uses partial pressures of H2, CO, CO2, CH4 (methane), water vapor, and a temperature-dependent term to predict the rate of reaction. The reduction rate (weight loss per unit of time) was determined with a thermo-gravimetric apparatus (TGA) in the temperature range of 800° to 1,100° C. The ranking of the reductants, in order of decreasing reducing potential, is H2, CO, and CH4 at temperatures between 800° and 1,000° C; however, CH4 became a better reductant than CO at 1,100° C. Water vapor did not decrease the reduction rate as much as did CO2, Carbon deposition was observed at temperatures below 1,000° C with gas mixtures with high CO and low H2 concentrations. With low-Btu gas at 900° C, over 90 pct of the iron oxide was reduced to iron in less than 3 h. This com-pares with a reduction time of 1.5 h with medium-Btu gas and 1 h with reformed natural gases.

Jan 1, 1985

By Pedro Lilienfeld

This report describes the development, design, fabrication and testing of a port-able, battery-operated, light scattering monitor (henceforth to be designated as ILSDM) for the rapid measurement of the concentration of respirable dust in mining environments. This instrument incorporates state-of-the-art design characteristics and makes use of advanced solid-state components both for light emission as well as for its detection. The use of a pulsed light source combined with synchronous signal detection minimizes drift problems and optimizes the sensitivity of the measurement. Simplicity of operation, reliability and ruggedness, light weight as well as improved performance were salient objectives of this instrument development program. Continuous clean-air flow screening of all critical optical surfaces, and optimized optical detection and electronic signal processing design resulted in about a hundred-fold decrease of noise and drift with respect to precursor instruments. Equivalent mass concentration measurements 88 low as 10 micrograms per cubic meter can be routinely performed with time constants of about 2 second.

Jan 1, 1979

By A. C. Fieldner

"Purpose and Nature of Tests:The rapidly increasing use of motor vehicles and trucks in the United States is creating an entirely new problem in the proper ventilation of tunnels, subways and other confined spaces through which such machines must pass. This problem has become of immediate importance because a tunnel 3,000 ft. long is being designed to pass under the Hudson River between New York City and New Jersey. Another tunnel at Pittsburgh 5,700 ft. long through the South Hills, is already under construction, and a third tunnel, 6,000 ft. between Boston and Past Boston is proposed. It is probably that other tunnels will be started in various parts of the United States in the near future.The ventilation of such tunnels is a serious matter, on account of the poisonous nature of automobile exhaust gases. It not uncommon to read about finding a man dead in his garage. Generally this happens on a cold, winter morning, after he has been running the engine with the doors and windows closed."

Mar 1, 1920

By R. E. Lindstrom

A study of ion-exchange resin crosslinkage and eluant flow rate, resin-bed shape, and addition of separating ions to feed stock was undertaken to determine their effect on the separation efficiency of ion-exchange on bastna-site-rare-earth elements. Results show that 12-percent divinylbenzene (DVB) crosslinkage resin is detrimental to separation efficiency at flow rates over 2 to 5 ml./min./sq. cm.; whereas, separation with 4-percent DVB crosslinkage resin is relatively unaffected by flow rates between 2 and 10 m1./min./sq.cm.

Jan 1, 1959

By L. D. Schmidt, Wm. Seymour, W. S. Landers

"INTRODUCTION The relative value of the various individual physical and chemical properties of coke as a measure of its performance in the blast furnace as aroused considerable controversy but it is generally agreed that uniformity in these properties is extremely important if maximum mum pip-iron production is to be attained. The control of,the bulk density or weight per cubic feet of the coal charge in the coke ovens is a major, and frequently overlooked, factor in producing a uniform product and in efficient operation of the coke plant.This report presents a brief discussion of the general problem of bulk-density control and the results of tests on samples of coke-oven charges from several operating plants experiencing difficulties due to lack of adequate control. These tests covered the effect of moisture and oil content on the bulk density of the coal. Some tests on the effect of a wetting agent and furnenous of gained were also made. A description of the methods used to determine the bulk density of the coals studied in this investigation and of the methods used to apply oil to the coal at byproduct-coke plants are included in this product. No theoretical analysis of the data presented in this report, because the primary purpose of the investigation was to obtain data of immediate practical value to the plants concerned."

Apr 1, 1945

By J. M. Singer

Methods are proposed for predicting concentrations of nitrogen oxides and carbon monoxide in the combustion gases of flames, specifically of lean, stoichiometric, and rich propane-air flames. Calculations are based on kinetic and thermodynamic theory. These theoretical data are compared with concentrations observed experimentally downstream of flat grid-type burner flames (approximately 25,000 Btu/hr) that were used to simulate gas appliances such as water and space heaters. Air pollutant concentrations are also computed for (1) flames chemically perturbed by recycling flue gases into the primary fuel-air mixtures; (2) flames thermally perturbed by cooling the burned gases at different rates; and (3) flames perturbed by combination of these two effects. In general, experimental and computed concentrations agree to within a factor of 2 to 7 with the experimental values always being higher than the theoretical. The theoretical analysis indicates that cooling the primary flame by recycling cold flue gases (with and without excess air) reduces the relative emission of nitric oxide and increases emission of carbon monoxide if the flame stoichiometry does not radically change. Cooling rates of about 5,500° to 10,000° R/sec starting at about 3,500° R generally suffice to prevent nitric oxide concentrations in lean flames from increasing much above the initial values at the combustion zone; these same cooling rates do not prevent oxidation of most of the initial carbon monoxide.

Jan 1, 1967

By J. W. Thompson

CONVEYANCE OF COAL IN PLACES. Coal or other mineral in place may be granted and conveyed as land, separate and apart from that which underlies or overlies it. Board, etc., of Greene County v. Lattas Creek Coal Co., 100 Northeastern, 561 (Indiana), January, 1913. MINERALS SUBJECT OF GRANT. Coal, mineral, and stone under the surface of the earth are the subject of grant and exception, and when excepted in a deed become a separate and distinct inheritance. Gordon v. Million, 154 Southwestern, 99 (Missouri), February, 1913. CONVEYANCE BY ONE COTENANT. One cotenant of land can not make a valid conveyance as against his cotenants of the minerals therein and a right to the small timber on the surface necessary for mining purposes with easements and full rights of way over the premises by the construction of roads, tram- ways, or railroads for the purpose of extracting, storing, handling, and shipping the mineral products. Ball v. Clark, 150 Southwestern, 359 (Kentucky), November, 1912. CONTRACT OF SALE COVENANTS RUNNING WITH LAND. Where a deed was made pursuant to a contract for the sale of certain copper-mining property at an agreed price, and at the same time and as a part of the same transaction a written agreement was

Jan 1, 1913

By James C. Fowler

The design and field testing of a seismic miner detection and location system arc described. This work was carried out over a period of three years. The first two and one-half years were sponsored by Continental Oil Company, while the last period of tests were done as the first part of a one-year contract with the U.S. Bureau of Mines. Laboratory and field experimentation in three different nines under simulated emergency conditions have led to three important results: (1) Taps on roof bolts with normally available objects can usually be detected up to horizontal distances of 1,000 ft. (2) The origin of the tans can be located by on-site processing with a small computer. (3) Some predetermination of the approximate location is necessary for a quick and successful rescue. This report also includes preliminary specifications an,d cost guidelines for construction of a transportable field system capable of matching the performance characteristics of the one used during the field tests.

Jan 1, 1973

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

1. Mine drainage constitutes surface or ground water which flows from mines or mine sites and is usually characterized by concentrations of acidity or alkalinity. 2. The regional geology controlling the ground water flow pattern in conjunction with the life cycle mining plan can serve as a basis for making decisions about quality of water that can be expected to be encountered. 3. In regard to the prevention and control of acid water formation in underground coal mines, much is left undone in research and education: (A) Very little literature is available on this specific subject although much has been written on water management in underground mines. (B) Little or nothing is contained in the text books and curricula used in mining departments at colleges and universities with the result that educational offerings may be seriously deficient in these areas. 4. Prohibiting water entry into underground coal mines is the best method of preventing water pollution. Since this is not possible as mining operations are extended, preventing water or oxygen from contacting acid producing material may offer the next best alternative. 5. More emphasis is needed during the mine planning stage on steps to prevent water pollution. Such life cycle considerations as type of mining, sequence of development and spatial configuration as well as the elements of the drainage network and final network organization and extent must be considered.

Jan 1, 1970

By L. C. George

The Bureau of Mines measured vapor pressures of selected mixtures in the binary system SnCla-ZnC12 by the static pressure method. Equations expressing the vapor pressure) and the heat and free energy of vaporization) as functions of temperature were developed by numerical analysis based on the sigma-plot method. It was found that the vapor pressure of any SnCl2-ZnCl2 mixture) at any temperature within the range of this investigation) could be accurately calculated from the derived values for the heat and free energy of vaporization for the mixture, with a probable error of 0.01 cm Hg or less.

Jan 1, 1967

By R. J. Leary

This investigation was conducted to determine the effects of various rare-earth metal addition practices upon the macrostructure and the pattern of sulfur distribution in steel ingots. Heats of plain carbon steel were melted in a 1-ton, basic electric-arc furnace. Melts were treated with mixtures of rare-earth silicides, aluminum, and cryolite either in the furnace before tap or in the ladle after tap to determine the effects of this form of rare-earth treatment upon ingot macrostructure. Steels thus treated with rare earths in the furnace were characteristically free of the gross subsurface nonmetallics which typically result from conventional rare-earth treatments. Steel treated in the ladle showed only a few such nonmetallics, and practical techniques were developed for eliminating most of these. Results showed that furnace deoxidation was controlled by the concentration ratio of rare earths: aluminum. During casting, deoxidation was controlled by the concentration of rare earths. Oxygen contents equivalent to vacuum ladle degassing resulted from air-melt furnace treatments with the rare-earth mixtures described. Rare earths in steel inhibited the onset of equiaxed grain formation during ingot freezing, and also virtually prevented interdendritic segregation of sulfides.

Jan 1, 1968

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics of positive corona are presented for air in a 2 - in - diam electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig . Results show that current - voltage relationships depend solely on air density . Comparison of data on positive corona with previously published data on negative corona demonstrates a higher sparkover voltage and a wider range of operability for positive corona at temperatures above 375 ° F. The possibility of achieving higher voltages with positive polarity as indicated by these experiments implies several advantages for the use of positive corona in precipitators to allow better removal of suspended material from hot gases . Based on the physics of an ion in an electrical field , a theoretical equation is derived to define current - voltage characteristics of positive corona in terms of air density . Constants for the equation are evaluated from Calculated current - voltage values at different air densities agree reasonably well with experimental data .

Jan 1, 1964

By H. M. Lawrence, E. Roca

"INTRODUCTION Of the phosphate rock deposits of the United States that are being exploited actively at present, the land-pebble area in Florida is the largest producer. In recent years the land-pebble district, in Polk and Hillsborough Counties, has produced about 80 per cent of the raw phosphate rock that has supplied the requirements of the several national industries based on this essential commodity.In the land-pebble deposits sizes finer than 16 to 22 mesh are below the commercial limit in phosphate content, and washing-plant practice has been directed to the recovery of the coarser material. Recently, more extensive control of the washery plan has resulted in the saving of additional amounts of phosphate, the loss of which had been considered unavoidable. However, strict requirements of the trade regarding the lowest acceptable grade of phosphate rock prevent the inclusion of more than a very small proportion of the low-grade phosphatic sands with the washery output of phosphate roe:. Further advances in practice resulting in larger recoveries of phosphate can only be effected by the application of processes that are based on other principles than merely a difference of particle size. Research is be conducted actively along these lines by the industry and by cooperating agencies.Flotation has been studied for several years by the International Agricultural Corporation and its allied company, the Phosphate Recovery Corporation. J. T. Burrows, vice-president of the International Agricultural Corporation, in a letter dated July 10, 1929, states:"

Aug 1, 1931

By William Seymour, L. D. Schmidt

"FOREWORDAmong many problems created by World War II, the question of supplies and distribution of raw materials is of outstanding importance. One of the most critical of these raw materials is fuel, and of the fuels coal is of primary importance. The normal consumption of coal has increased greatly owing to the increased tempo of industry in general. It has been necessary to divert much of the fuel oil, gasoline, etc., ordinarily used for industrial and domestic purposes, to supply the enormous demands of mechanized warfare. Coal must be provided to replace this fuel. Furthermore, the enormous increase in the production of steel has increased the demand for coking coals to a critical point.The Solid Fuels Administration for War is encouraging the use of anthracite fines in the production of byproduct coke for blast furnaces for three reasons. First, the production of anthracite for domestic use; is hampered by the inability to find a market for the fines incidental to the production of domestic sizes. Second, the shortage of low-volatile coking coal is acute, and any action that will decrease the quantity of low-volatile coal required will relieve the situation. As will be seen in this report, there is some promise that use of anthracite fines in coke-oven mixes will lower the amounts of low-volatile coal required. Third, utilization of those anthracite fines will tend also to alleviate the general fuel shortage. It has been the privilege of the Bureau of Mines to cooperate with the Solid Fuels Administration in the technical problems involved."

Apr 1, 1945

By F. M. Goodwin, Campbell. John, W. J. Hiffs, G. W. Jones

"INTRODUCTION In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co. a survey has been conducted continuously since 1929 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933.Yearly reports 6 giving the results obtained since the start of the survey have been published.The method and procedure of conductin, the survey in 1935 were the same as heretofore.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of F. D. Comerford, president of the Edison Electric Illuminating Co. of Boston; E. N. Farnesworth, Jr., vice president and general manager of the Boston Consolidated Gas Co.; and A. C. Fieldner chief engineer, Experiment Stations Division, U. S. Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department, of the Edison Electric Illuminating Co., cooperated in furnishing men and information for the work,"

Oct 1, 1936

By H. S. Kalman

A table of factors, for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, is presented. By use of the table the volume of helium in a container, at base conditions of 14.7 psia and 70° F, can be calculated from the observed pressure and temperature of the helium and the known internal volume of the container. The table covers a pressure range from a to 4,500 psia in 10 psi increments and a temperature range of 0° to 120° F in 2° increments. The calculation of volume requires a single multiplication, using a factor from the table and the known internal volume of the container. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1963

By H. S. Kalman

A table of factors, for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, is presented. By use of the table the volume of helium in a container, at base conditions of 14.7 psia and 70° F, can be calculated from the observed pressure and temperature of the helium and the known internal volume of the container. The table covers a pressure range from 0 to 4,500 psia in 10 psi increments and a temperature range of 0° to 120° F in 2° increments. The calculation of volume requires a single multiplication, using a factor from the table and the known internal volume of the container. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1963

By W. W. Adams

"The ninth yearly National Safety Competition covering the calendar year 1933, conducted by the United States Bureau of Mines, w participated in by 332 mines and quarries situated in 35 States. Enrollment represented as increase of 10 plants over 1932, and one addition was made to the number of States represented.The primary purpose of the United. States Bureau of Mines in conducting the contest is to promote safety in United States mineral industries. This purpose is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive recognition on a national scale for their achievement the purpose is accomplished indirectly through studies by the United States Bureau of Mines of the facts contained in the accident reports the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics which constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting, from industrial accidents.Bronze trophies, known as 'Sentinels of Safety', which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were presented to five companies in the contest of 1933, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or opencut mines. The trophies are awarded for 1 year and are then transferred to the winners of the succeeding year's contest.The trophy for bituincus-coal mines was won by a company in Wyoming. A company in Tennessee won the trophy for metal mining. In the nonmetal-mine group the trophy was again won by a company in New York. A quarry in Michigan won the trophy for the quarry-and-opencut-mine group. The trophy for anthracite mines remains in Pennsylvania, as all anthracite mines in the contest are in that State."

Jul 1, 1934

By Clarence Karr

RESINS from a bituminous pitch, a bituminous coal, a lignite tar, a subbituminous pitch, and an electrode binder pitch wore investigated by the Bureau of Mines. The compositions of these resins were determined by four independent methods of structural detemination: (1) Molecular formula and ring analysis, including ring (2) infrared and ultraviolet spectra; (3) combined pyrolysis/gas chromatography, and (4) catalytic dehyrogenation followed by spectra and pyrolysis. The resin structure was correlated with coal structure, and it was concluded that pitch resins probably consist of essentially unaltered coal molecules carried over with the tar vapors in low-temperature carbonization.

Jan 1, 1966