Search Documents

Preventive maintenance practices are listed in the manufacturers' instruction books. In general, equipment that requires frequent and extensive preventive maintenance is generally the most costly. The manpower spent on these frequent trips to remote areas is such that it is usually better to invest in a more costly system which requires little preventive maintenance. The best preventive maintenance for the system is a good installation. 7.2 Preventive Maintenance and Inspections With any system, periodic inspection is required because of the corrosive atmosphere and adverse conditions that exist in underground mines. These inspections can spot potential trouble in the system. Repair or replacement at that time averts the possibility of losing effectiveness of all or part of the system. 7.2.1 Cables Approximately once per month all cables in the communications system should be inspected for kinking, chafing, cracking, wear, stretching, or other signs of physical abuse. Particular attention should be paid to cable glands at the entry or exit points to the various units in the system, where the cable goes around sharp corners, in the vicinity of holding cleats which may be clamping the cable too tightly causing potential damage, and across the areas where the cable is exposed to physical damage from outside sources, such as equipment or falling objects. If a cable is damaged, it should be replaced as soon as possible. It is mandatory that the ground leads and connections to carrier current phones be thoroughly inspected and maintained in good condition, since considerable hazard may exist to the operator or equipment if a ground connection is broken. 7.2.2 Pager Phones The most readily available test set to determine if a pager telephone is operating correctly is the pager phone itself. The following physical check of the system can be performed at any phone station. 7.2.2a Listen Circuit Remove the handset from its cradle and listen to determine if the circuit is functional, as indicated by the presence of noise or conversation on the line. If no noise or voice signals are present at the handset receiver, take the following corrective action: 1. Operate the handset press-to-talk switch several times. Any corrosion on the contacts of this switch may cause a receiver to be temporarily inoperative. Repeated operation may clear the condition. 2. Open the cabinet and see if the battery cables are properly connected and are making firm contact. Check the handset cable and its connections in the cabinet of the pager phone, and see if there is any evidence of a break in the cable, corroded contacts, or poor connections. 3. Remove the handset receiver earpiece by unscrewing it counterclockwise (to the left), and remove the receiver from the socket. Examine the handset cavity; in some units, a patch of cotton batting or floss is used as a barrier to reduce acoustic feedback in the handset. If the cotton patch has absorbed moisture, remove it and replace with a crumpled ball of soft rubber, stuffed just far enough into the handset so it will not touch the receiver or switch terminals. 7.2.2b Page Circuit and Talk Circuit Push the page switch, squeeze the handset press-to-talk switch, and call any other phone. Release the page switch

Jan 1, 1984

By Philip C. Good

The Bureau of Mines investigated the feasibility of utilizing low-grade phosphatic shale as a feed for phosphoric acid production. Present practice in the phosphate mining operations of southeastern Idaho is to remove and either stockpile or waste low-grade phosphatic shales as the high-grade phosphate beds are selectively mined. Acid digestion studies were performed on uncalcined shale and on shale calcined to remove free carbon to determine phosphoric acid quality, yield, and amenability to filtration. The untreated shale, containing 21.4 pct P205, was digested with sulfuric acid in a single-tank reactor to yield phosporic acid and gypsum residue. Although 96 pct P205 recovery was attained in digesting uncalcined shale, only the calcined product gave satisfactory filtration rates. Calcined shale yielded phosphoric acid recovery of about 93 pct of the contained P205. It was higher in impurities than commercially prepared acid derived from high-grade western phosphate rock. An acid filtration rate of 745 lb P205/ft2/day was attained. This value is lower than the rate of 900 lb P205/ft that is generally considered to be acceptable in industrial production of phosphoric acid from high-grade phosphate rock.

Jan 1, 1981

By Eugene T. Sheridan

The annual survey of the fuel-briquet industry by the Bureau of Mines, United States Department of the Interior, revealed that 21 fuel-briquet plants in 11 States were in operation and reported production in 1956. The demand for fuel briquets in the United States has gradually declined since 1948, and the number of operating plants has decreased from 36 to 21. Also, the annual productive capacity of the industry has decreased, although not a proportionate amount because most of the plants that were abandoned were small and in most instances had a designed capacity of less than 25,000 tons per year. In 1956 the 21 active plants had an annual capacity of 3.7 million tons (table 2), which was only 20 percent less than the total capacity of the 36 plants in 1948. This indicates that most of the larger plants have remained active, even though operating at reduced rates, and the average capacity of the industry has increased from 130,000 tons per plant in 1948 to 177,000 tons in 1956. Since 1948 operating rates have decreased from 67 percent to 41 percent of annual capacity.

Jan 1, 1958

By Alphonso Cornejo, Galen H. Clevenger

This bibliography was compiled in connection with an investigation of the Caron process for the treatment of manganese - silver ores , conducted by the T. S. Bureau of Mines in cooperation with the Netherlands East Indies Government . The object of this investigation was to develop a practicable method for treating the refractory manganese- silver ores found in these two countries . The results of the work will be published as a bulletin of the Bureau of Mines . This bibliography summarizes the available information on the subject previous to the investigative work embodied in the forthcoming bulletin, and may be useful to those metallurgists or others conducting work along this line .

Mar 1, 1923

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not generally been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. miners are required to have annual safety training, but they rarely view this positively. In fact, it has been called “safety jail” by many of them, who regard it as a time to get a little extra sleep. The challenge then, was to find a way to develop effective safety training for these people, particularly in view of the fact that their work is among the most dangerous of all occupations. Miners are born story tellers. They share “near-miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environ-ment, they also instruct listeners in the culture of mining and the values it embraces. Stories, it seems, are a way to get safety messages to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how the training videos created to get safety messages to miners were developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.

By Edward W. Ames

"The Jewell tunnel property, situated 3/miles north of Garfield, Chaffee County, Colo., was examined by an engineer3 of the Bureau of Mines in June 1943. Field work began September 16, 1944, but was recessed from December 26, 1944, to gay 15, 1945, because of heavy snows, and was suspended July 12, 1945, when rehabilitation of the New York tunnel workings was completed to the point desired.In its program of exploration of Mineral deposits, the Bureau of Lines has as its promary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as seen .as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples of ore and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.For their supervision of the project and their help in revising the report, particular acknowledgment is due Wm. P. Huleatt, district engineer, Denver, Colo., and Paul T. Allsman, chief, Salt Lake City Division, Mining Branch.The property is situated in secs. 15 and 22, T. 40 N., R. 6 E., N.R.F.M. Salida, the county seat, is on the main line of the Denver & Rio Grande Western Railroad. The property is reached from Salida by following U. S. Highway 50 westward for 18 miles to the village of Garfield, near Monarch Pass, then northward for 3 miles by a very steep mine-access road up Taylor Gulch (fig. 1).The highway to Garfield is accessible throughout the year, but the access road from Garfield is generally impassable from December until June because of snow."

Sep 1, 1946

By William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to support the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By D. T. Hahn

Adequate and cost effective erosion control is an important component in most plans for reclamation of surface mined land. Despite the fact that much is known about erosion of agricultural lands, insufficient conclusive knowledge is available about erosion of reclaimed surface mined land. Our study was conducted to characterize the erodibility of reclaimed surface mine land relative to unmined cropped land, and to evaluate the accuracy of the universal soil loss equation (USLE) in estimating erosion from reclaimed soils. A rainfall simulator was used to measure runoff and erosion rates from plots at three Indiana surface mines. The relation of erosion of the reclaimed soils was not completely constant with that from the cropped soils. Significant differences in erodibility were observed between reclaimed and nonreclaimed top soils, as well as reclaimed topsoils and reclaimed subsoils.

Jan 1, 2011

By E. P. Youngman

The mining law of British North Borneo is entitled " The Mining Ordinance , 1927. 113 The only mining regulation or rule available is " Rules 313 , 114 passed in accordance with article 26 of the ordinance of 1927. Before the passage of this legislation , the country had no specific law governing the granting of mineral rights , although the land law contained provisions relating to mining lands . The land ordinance of 19135 still controls in a few details . All references in this paper , unless otherwise specifically designated , are to the mining ordinance .

Mar 1, 1933

By David C. Oyler, Herbert H. Fields, William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to sup- port the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By IRENE AITKENS

The Mining Law of 1910 , with amendments of 1914 and 1928 , is at present in force in the Dominican Republic . The first and basic mining law of the Republic was passed in 1876 , and although numerous changes and amendments have been made from time to time , the new laws and amendments thereto have not changed the original or basic law materially . However , these enactments have materially changed the legal methods governing the exploitation of the mineral resources of this country and have added new regulations and requirements to those concerning certain specific minerals , etc. The original or basic law still exists as it was first promulgated to protect the rights of the Dominican Republic itself , the rights of the landowner , and the rights of prospectors in general . The Mining Law of 1876 remained in force , without amendment , until it was superseded by the law of May 25 , 1904 , an enactment modeled after the Mexican mining law and designed especially to encourage the investment of

May 1, 1931

By Eliezer Kamon

To finalize the three years granted for the study of miners physiological responses to emergency situations, all the data obtained, were summarized into the following relevant sections; A.. Information on elements of the Man Test required under Subpart 4, Part 2, Title 30 in the Code of Federal Regulation (see Table M-T and Ref. I., Section A). B. Investigation on possible emergency activities, its simulation in the laboratory and the physiologic data obtained on miners performing them This included some studies under cool ambient conditions, expected to prevail in coal mines. C. While in section B the steady state responses have been obtained, time was devoted to establish a unit that will allow data gathering for non-steady state, i.e., transient responses to rapidly changing activities. Section B and C contained elements that were relevant to section A; the Man Test. Therefore some of the information described under section A Man Test, were actually measured during the battery of tests in either section B or in section C.

Jan 1, 1974

By Arthur B. Johnson

The Bureau of Mines investigated the concentration characteristics of high-clay sylvinite ores from four potash companies operating in the Permian Basin near Carlsbad, N. Mex. These ores, containing 13 to 22 percent K20 and 3 to 7 percent clay slimes, cannot be effectively processed by current commercial flotation methods because of their high slime content. A solution to this problem was shown to be the use of two-stage moderate scrubbing conditions and washing of the ore as opposed to strenuous attritioning. Bench-scale physical beneficiation techniques for recovering potash minerals and the development of ore-dressing systems by flotation resulted in obtaining acceptable product grades and recoveries. By using a coarse grind, emphasis was placed on production of premium granular and coarse products. Flotation results showed that concentrates of 58.7 to 60.4 percent K20 with recoveries of 71.0 to 83.4 percent 0f the K20 values can be obtained.

Jan 1, 1971

By F. C. Gregory

"Introduction.The third annual mine-rescue maneuvers of the Globe-Miami District First Aid and Mine Rescue Association were held at Globe, Ariz., on November 5 and 6, 1923. The first demonstration was held in October 1922, and the results** from that experiment, both in the practical training and the interest aroused in the apparatus men, were so much more satisfactory than those from the ordinary smoke-chamber training, that Orr Woodburn, director of the Association, decided to hold similar maneuvers at frequent intervals. The second test was held on March 21-22, 1923, in connection with the meeting of the Southwest Mining Section of the National Safety Council at Globe.Place and Organization.The recent maneuvers were held in the same mine and conducted in the same general manner as the first, and the points of interest not brought out previously are described below. By studying the accompanying map the movement of the teams can be better understood.Thirty-three apparatus men were out on the first day and thirty-two on the second day, a total of forty-three men being trained.Mr. Woodburn was aided in directing the work by his two assistants from the mine-rescue station, two local safety engineers, and an engineer from the Bureau of Mines. Local mine superintendents and the State deputy mine inspector were interested spectators."

Jan 1, 1924

By W. L. Hunter

This report describes results of beneficiation and smelting studies conducted by the Federal Bureau of Mines on chromite samples from the Emma Belle and Seiad Creek prospects in the Seiad Creek area, northern California. Samples were chosen from this area because the ore is typical of disseminated types that represent a sizable domestic reserve. The two samples were similar in composition, and both responded in like manner to gravity beneficiation. As the ore was banded, considerable coarse gangue was rejected in laboratory sink-float from a minus-3/4-inch, plus-6-mesh fraction without excessive chromium loss at a medium density of 3.32. An average of 85.6 percent of the chromium was recovered in the sink product, which analyzed 35 percent chromic oxide (Cr203). Tabling yielded concentrates containing 49 percent or more Cr203; however, recoveries, ranged from only 33 to 45 percent. A combination of tabling and electrostatic separation of the table middlings showed that the chromium recovery could be increased to about 73 percent; the composite concentrate averaged 53 percent Cr203.

Jan 1, 1960

By Eugene T. Sheridan

The 22d annual survey of the packaged-fuel industry by the Bureau of Mines, United States Department of the Interior, revealed that 26 plants in 8 States were in operation and reported production in 1956. The demand for packaged fuel in the United States has declined gradually since the end of World War II, and the number of operating plants has decreased from 70 in 1946 to 26 in 1956. Annual productive capacity of the industry has decreased also during this period, and the decrease in capacity was about proportional to the decrease in operating plants. Packaged-fuel plants are relatively small, and 85 percent of the active plants in 1956 had an annual capacity of less than 10,000 tons. The same situation prevailed in 1946, when 84 percent of the plants had a capacity of less than 10,000 tons. Total capacity for the 26 active plants in 1956 was 174,600 tons, an average of 6,715 tons per plant. Operating rates in 1956 were the highest since 1951, and the rate of production for the industry averaged 37 percent of capacity.

Jan 1, 1958

"To prevent the propagation of mine explosions, the Bureau of Mines recommends:1. That all coal and lignite mines, except anthracite mines shall be rock dusted.2. That rock dust shall be distributed upon top, bottom, and sides of all underground openings of every description, to within. at least 4o feet of all working faces and the areas not rock dusted shall be kept wet.3. That the rock dust shall be maintained in, such quantity that the incombustible material in representative samples of dust collected shall not be less than 65 percent. Where methane gas is present in the ventilating current, the minimum percentage of incombustible matter in the mine dust shall be increased 1 percent for each 0.1 percent of methane.4. That when the rock dust in any area becomes caked so thatit cannot be dispersed readily as a cloud in the air, that part of the mine shall be redusted immediately.5. That the dust to be used shall not contain more than 5 percent of combustible matter nor. more than 25 percent of quartz or free silica; all of the dust shall pass through a sieve having 20 meshes per linear inch and 60 percent or more shall pass through a sieve having 200 meshes per linear inch; the dust shall not absorb moisture from the air to such an extent as to cake and destroy its effectiveness as a dry dust.6. That rock-dust barriers shall not be regarded as a substitute for generalized rock dusting.Research and experience have shown that maintenance of an adequate percentage of rock dust in all underground openings, whether gassy or not, of bituminous and subbituminous coal and lignite mines (anthracite dust does not propagate explosions) is the best means of preventing coal dust explosions. In rare instances where all fine coal particles on the floor, ribs, roof, and timbers are in a muddy condition continuously rock dusting is unnecessary.The term ""underground openings"" refers to all unsealed openings whether they contain track or not, and includes rooms, entries, crosscuts, breakthroughs, rock tunnels, slopes, haulageways, airways, and travelingways. The sealing of unused or abandoned parts of a mine in accordance with Mine Safety Board Decision avoids the necessity of rock-dusting the sealed-off openings.The kind of rock dust to be used should have the approval of the State Mine Inspection Service. Pure limestone or pare dolomite produces the best rock dust, as these dusts have low silica content, little tendency to cake, and a light color that aids illumination. To reduce tendency to cake it is preferable that not more than 75 percent of the dust pass the 200-mesh sieve. All sieve sizes are those of the Tyler screen scale. If the mine personnel is repeatedly exposed to breathing high concentrations of the dust, the percentage of free and combined silica should be as low as possible, preferably less than 5 percent. Persons engaged in the application of rock dust should wear approved dust respirators as listed in Bureau of Mines Information Circular 7030 or revisions thereof."

Mar 1, 1940

By Edward Thomas

In 1947 the Bureau of Mines, as an accident-prevention measure, decided to advocate the adoption of roof bolting (suspension roof supports) in coal mines where it appeared to be applicable. Subsequent experience has disclosed that the applicability of this support is more general than was first suspected; moreover, comparison of the accident records of mines before and after adoption of the roof-bolting method shows results that more than justify the effort and funds expended. The industry has responded enthusiastically, because roof bolting proved to be not only an accident-prevention measure but also one to increase productive efficiency. In some instances this increase in the productivity of men and machines has been almost incredible and has led many mining men to conclude that through some hocus-pocus they can now cast aside many or all of the time-proven rule of good mining practice. If this tendency is not counteracted, it could easily result in an increase of roof-fall accidents, which may outweigh the benefits of roof bolting and discredit an innovation in roof control that shows great promise of materially reducing our mining accidents. From an economic standpoint it may represent the margin between profit and loss in many mining operations. The purpose of this manuscript is not to propose an inflexible code or set of rules but to summarize the experience to date as a guide for those who have the responsibility for the installation and inspection of roof bolts. This experience consists of approximately 250 investigations of roof failure in which roof bolting was involved either directly or indirectly. It should be pointed out that many of these failures were controlled, occurring during experimental periods, and comparatively few of the accidental failures actually resulted in personal injury, yet a significant number represented potential hazards.

Jan 1, 1951

By Scott W. Hazen

METHODS of determining the grade and tonnage in a mineral deposit have not kept pace with scientific developments in certain other fields. The most commonly used methods of computing ore reserves and grade based on diamond-core-drill sampling are the cross section, the polygon, and the triangle. Tonnage and grade may be determined by these methods with acceptable accuracy, providing a sufficient number of samples is obtained; however, there is no means of determining when an adequate number has been taken or conversely if the deposit has been sampled excessively. It is demonstrated that, by using the techniques of statistical analysis, a mining engineer will be able to determine when a sufficient number of samples has been taken to determine the grade of a mineral deposit within a specified degree of confidence. Using statistical analysis to compute the estimated average grade of the ore makes it possible to compute a fiducial interval, when a distribution of the sample means is normally distributed, so that there is 95-percent confidence in the statement that the true average grade of the deposit is covered by the interval. This report utilizes data obtained from the Maggie Canyon manganese deposit, Artillery Mountains region, Mohave County, Ariz. Four separate exploration projects were conducted at Maggie Canyon between 1936 and 1950. Present economic conditions have made it desirable to determine the amount of 5-percent manganese ore developed by these projects.

Jan 1, 1957

By Richard H. Oitto

The Bureau of Mines and Kaiser Steel Corp. are cooperatively demonstrating the shield-type roof support in the longwall mining of a 10-1/2-foot-thick coalbed at the York Canyon mine near Raton, N. Mex. As part of the demonstration, the shield supports have been successfully and safely moved from a completed longwall face to a new longwall face. When these shield supports were moved in 1976 they were the largest and heaviest longwall support system in use in U.S. coal mines. The shield supports, preparations for moving them, the actual move, and installation at the new face are discussed.

Jan 1, 1977