Search Documents

By K. L. Rubow

"IntroductionAir sampling for airborne contaminants requires a system for moving air, a collection method, and a procedure to determine the quantity of contaminant collected. Because occupational exposure limits and air quality standards frequently are expressed in terms of concentrations, a method of determining the volume of air sampled is also needed. The four principal components in a sampling train are shown in Figure 12-1. The inlet admits the air sample into the train; the collector(s) separates the gas, vapor, or particles from the air; the flowmeter measures the rate or total quantity of air sampled; and the pump (air mover) provides the suction required to draw an air sample through the train. Inlet sampling considerations are discussed in Chapter 21. Various types of collectors are described in subsequent chapters. Flowmeters are discussed in Chapter 7.This chapter will describe the air mover portion of the sampling train and air sampling systems that contain three or four components in a convenient package. The chapter consists of two parts. The first part contains a brief description of the different types of air movers and air sampling systems. The second part consists of tables and figures showing detailed information on a wide variety of commercially available air movers and sampling systems. ient size is filled with a liquid in which the suspected contaminant is insoluble. When the liquid is allowed to escape from the vessel, it is replaced by air from the atmosphere to be sampled. Such an air sample is an integrated sample rather than an instantaneous sample because the mass of fluid requires a finite time to empty. In fact, by employing a large vessel with controlled drainage, this method can be used to move air at low flow rates through a sample collector for extended intervals. Additional discussion of this method can be found in Chapter 17."

Dec 1, 1996

By Daryl E. Radcliffe

The Bureau of Mines studied the displacement of the roof in a portion of the Bear coal mine near Somerset, Colo, Horizontal-and vertical-displacement gages were installed in a five-entry section during normal room-and-pillar mining procedures. Monitoring of the roof continued until this section was mined out. Displacement measurements in combination with known time lapses between mining and bolting operations indicate that once support is achieved, the length of unsupported time does not appear to affect long-term roof stability in the mine under investigation.

Jan 1, 1978

By Gregory J. Chekan

As part of the initial investigation and validation of a new boundary-element formulation for stress modeling in coal mines, the underground stresses and displacements at two multiple-seam coal mines with unique stress problems were modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and nonlinear seam materials can be used, and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geomechanics based on previously observed stress conditions at the mine. For this calibration process, a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems ahead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 5, 1999

By H. C. Miller

"Introduction**The progress of the ""Safety First"" movement in the oil fields of California during the past few years has been remarkably rapid. It has been generally concede by those who have learned to value the life and limbs of their employees, that safety is essential to efficiency and no company that has a high accident rate can be considered an efficient organization. Accidents have a destructive effect on the morale of any body of workers and cause disorganization and delays.The increasing danger to life and limb involved in the drilling for and the production of oil and gas, has become so great that it is clearly evident that everything possible must be done to keep it within the narrowest possible limits.There is a tendency toward carelessness, especially by men who are employed in hazardous occupations. This is brought about by the familiarity of the risk under which they are working and in no industry is this more forcibly exemplified than in the oil fields. Men have performed the same or similar duties for many years and have worked around similar hazards and unprotected machinery until many have can entire disregard for the dangers surrounding then. Very often familiarity with a hazard occasions a contempt for that hazard which only too often results disastrously."

Dec 1, 1923

By Verne E. Hooker

The Bureau of Mines conducted a preliminary investigation to determine the state of stress in crystalline rock outcrops near Atlanta, Ga. The secondary principal stresses in a horizontal plane near the surface are compressive and are 500 to 3,000 psi. The maximum compressive stress is northeast-southwest in the Stone Mountain-Lithonia district but changes to northwest-southeast near Douglasville. The elastic constants were determined from data obtained by static and dynamic laboratory methods and in situ velocity measurements. Results show Young's modulus to be dependent upon both stress level and anisotropy in the rock. Average secant moduli obtained from triaxial tests were used to compute the applied stress from borehole deformation measurements.

Jan 1, 1966

By J. M. Kuchta

The Bureau of Mines investigated four simulated coal gob fires to obtain a more reliable data base for defining the state of a sealed mine fire and to evaluate the performance of various fire detectors. The fires were conducted in a multiple-entry section of the Bruceton Experimental Mine by heating 4,000 to 21,000 pounds of rubblized bituminous coal to ignition and monitoring the temperature, gas emissions, and smoke under ventilated and sealed combustion conditions. Product gas concentrations depended upon the coal bed size, coal temperature, heating rate, and oxygen concentration or ventilating condition but varied little after the fires were sealed. Expressions are given that define the temporal variation of CO and O2 after sealing when the coal temperature decreased rapidly. The CO/C02 ratio is a more sensitive fire indicator than the CO/?02 ratio, although the latter is universally used for detecting the incipient state of a coal fire. In comparison, the Jones-Trlckett ratio [ CO2 + ¾ CO ? ¼ H2 ?O2] is less reliable for this purpose. The best detector for determining the state of a mine fire after it has been sealed was a prototype submicrometer smoke particulate sensor. Limitations of the various detector systems are also discussed.

Jan 1, 1982

The National Institute for Occupational Safety and Health (NIOSH), in partnership with stakeholders in the mining and surface drilling industries, con-ducted research to develop engineering control technologies that reduce workplace noise exposure. The result of this research partnership is the development of a partial cab.

Jan 8, 2007

By C. L. Brown

Among the more recent developments for breaking coal in mines is the Airdox system, in which high-pressure compressed air is conducted to the points of application by means of heavy-duty steel and copper tubing. Stray electric currents can be detected on y of the compressed-air lines, and evidence of such currents is rev led, by arcs and sparks when contact is made between the tubing and mine track or other equipment forming a current path with the track. Explosive gas is liberated in many coal mines; therefore, from the standpoint of safety, it is desirable to eliminate all possible sources of gas ignition, including stray electric currents. The purpose of this report is to reveal the source, magnitude, and possible methods of controlling stray currents in compressed-air lines that are used in connection with Airdox systems. Stray electric currents have been studied in most coal-mining localities in the United. States where Airdox equipment is used. The information given in this report is based on the find of these studies.

Jan 1, 1949

By Manuel Gomez

This report presents experimental work conducted on a number of coals found within the boundaries of the Missouri River Basin, which were, to an extent, a selection of coals typical of that region. In the min, the laboratory work falls into three general classifications: (1) Laboratory distillation assay of coal to establish yields on carbonization; (2) chemical analyses of the coal samples before drying or carbonization; and (3) chemical analyses of the products of carbonization. It will be seen in the following discussion that these data derived from the small-scale laboratory apparatus are useful in predicting yields from pilot plants or industrial units. Coal is produced in about 48 general areas or mining fields in the Western States, of which approximately 18 fall within the limits of the Missouri Basin.3/ Beginning with the Northern Colorado field, through the Central and Western Wyoming fields, the coal is principally bituminous and subbituminous rank. The western Montana coals are also of these ranks. Progressing northeast from central Wyoming the coal decreases in rank, as shown by the subbituminous C coals of the Gillette field in northern Wyoming and the lignites of eastern Montana and North Dakota.

Jan 1, 1953

By G. W. Birge

Fifteen coal samples, representing the Winifrede, Chilton, Alma, No. 2 Gas, Powellton, Eagle, Douglas, Sewell, Beckley, Pocahontas No.4, and Pocahontas No.3 beds in Wyoming County, and five samples, representing the Fire Creek, Pocahontas No.6, and Pocahontas No.3 beds in Mercer County, W. Va., were carbonized at 9000 C by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expansion characteristics of the majority of samples were determined in the Bureau of Mines sole-heated oven. Chemical analyses and agglutinating values were determined for all coals. The coals were mostly strongly coking and low in ash and sulfur content. Dry, mineral-matter-free fixed-carbon content of the Wyoming County coals ranged from 63.0 to 83.4 percent. The Mercer County samples were all low volatile in rank. Yields of carbonization products were generally in accord with yields from similar rank coals of the Appalachian region. Because of their expanding tendencies, most of the medium-and low-volatile coals would require blending with lower rank coal for normal coke production.

Jan 1, 1965

By H. R. Pierce

A gas well has a certain definite capacity to deliver gas from the gas sand through the producing string of pipe. This capacity depends upon the pressures in the sand; that is, a well will deliver gas at a rate of flow which is determined by the formation or "shut-inn pressure in the sand and the back pressure at the face of the sand in the well. The three factors, rate of flow, formation or "shut-in" pressure, and the back pressure, for a given well, can be written into a fundamental relation which is strictly applicable only to that well. This relation can be used to determine the capacity of the well to deliver gas from any formation pressure against any back pressure held at the f ace of the sand in the well. Studies have been made of the deliveries of 400 gas wells operating under different conditions of pressure, Most of the wells which have been studied are in Osage County, Okla.; however, several representative studies have been made on wells in southern Louisiana, southern Texas, the Texas Panhandle, and West Virginia.

Jan 1, 1929

By Jacob Schoder

This is one of a series of papers published by the Bureau of Mines on mining and milling methods and costs. The Tennessee-Schuylkill Corporation, Chloride, Ariz., mines and mills a lead-zinc ore containing gold, silver, and a small amount of copper. The mill products are lead and zinc concentrates that are shipped to smelters. The company was the second largest producer of lead and zinc in Arizona in 1937 and was seventh in gold production. Operations discussed are those being conducted at the mine in October 1938 and are representative of the complete operating period from 1936 to date.

Jan 1, 1939

By Richard L. Sayrs

The Idol zinc prospect, formerly known as the Comstock, was examined by Harold B. Ewoldt, a Bureau of Mines' engineer, accompanied by Deane F. Kent of the United States Geological Survey on July 22, 1943. Previous to that time, the Geological Survey had contoured and studied the area. As a part of the war minerals program, further investigation of the area was recommended. The Dalton property, a mile and a half northeast of the Idol property, was examined during the progress of the work at the Idol, and it was decided to include this property also in the project. From February 7, 1944, to May 16, 1944, six holes totaling 2,739 feet were diamond-drilled on the Idol property and eight holes totaling 1,850 feet were diamond-drilled, and three pits channel sampled on the Dalton property. The drilling showed sphalerite to be sparsely distributed through a 100 foot thickness of the Kingsport member of the Knox dolomite.

Jan 1, 1949

By Martin S. Oudenhoven

This Bureau of Mines report presents the results of a microseismic study conducted in the Climax block cave mine at Climax, Colo. Rock noises created by caving were monitored and their sources located during a 3-month period. A planar array of seven accelerometers, located above the block of ore being caved, detected the rock noise. A computer was used to calculate the location of the microseismic activity, using a traveltime difference method. The accuracy of these locations was estimated to be ±20 feet. An analysis of the data taken during the recording period showed a concentration of microseismic events located in the wall of the cave panel. This concentration of events was found to occur in a "high-silica" geologic forma-tion that cut across the caving panel approximately 200 feet behind the undercut.

Jan 1, 1973

By Alan J. Fejes

As part of its mine subsidence research program, the Bureau of Mines and the American Electric Power Co. cooperated on a study, conducted at the Price River Coal Co. No. 3 Mine, directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. Subsidence was monitored at the No. 3 Mine over two adjacent longwall panels. The subsidence study area was reduced when the two planned panels were reduced in length because of equipment failure and a mine fire. Subsidence was measured for 21 months. Subsidence continued for 6 months after mining had been completed. A maximum of 2.2 ft of subsidence occurred over the two longwall panels mined at an overburden depth ranging from 300 to 1,500 ft.

Jan 1, 1986

By Frank C. Morris

It is generally recognized that the productivity and ultimate recovery of an oil well may be reduced as a result of reduction in permeability of the sand at the well bore by invasion of filtrates and clay particles from drilling fluids. As a means of determining whether a sand has been "damaged" from these sources, several investigators2 3 4 5/ have developed methods of analysis based on the rate of increase in bottom-hole pressure while a well is shut in. Because of growing recognition of the importance of completion practices as related to the quantity of oil that may be recovered from wells, the Bureau of Mines has studied completion practices in California and the Midcontinent area. Well-interference and pressure-buildup tests were completed Ear seven wells in the Scurry Reef field to determine the effective permeability in the reservoir.6/ Also, a study was made of the pressure-decline curves obtained from 35 water-input wells in 5 different production areas of northeastern Oklahoma and eastern Kansas.7/

Jan 1, 1957

By Walter Kawa

Bureau of Mines research on the hydrogenation of coal has been concerned with developing processes that could be used to supplement the Nation's petroleum and natural gas resources. Motor fuel was produced in a subsidized coal hydrogenation industry in Europe prior to 1945, but the process used is still not economical and other methods of producing liquid and gaseous fuels from coal are being investigated. As an aid to the planning of coal hydrogenation research, a literature survey was made of processes or methods of hydrogenating coal that differ from the subsidized or conventional process. This report contains a bibliography of unconventional methods of hydrogenating coal and a brief discussion of the economics of the conventional method. A general discussion of unconventional methods is included, and the advantages and disadvantages are pointed out where possible. The survey supplements a previous Bureau of Mines survey3 and a comprehensive review published in 1930.4

Jan 1, 1964

By Nicholas Kyriazi

The Bureau of Mines subjected three commercial compressed-oxygen self-contained self-rescuers to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The environmental treatments consisted of extremes of temperature and of shock and vibration. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. A critical concern was internal damage to an apparatus that would cause it to malfunction or seriously degrade its performance without any obvious external signs. The Bureau has previously tested chemical oxygen self-contained self-rescuers in a similar research program. Although the three compressed-oxygen units are not as sturdy as the chemical oxygen self-rescuers tested previously, they performed reliably after treatments on treadmill tests with human subjects and on machine tests using a breathing and metabolic simulator. Serious damage was caused by both the heat treat-ment of 71° C (venting of the 02 bottle in most cases), and in the shock treatment (breaking open of the case and dislodging of the components). When physical damage is obvious, a complete refurbishing of the damaged self-rescuer is recommended.

Jan 1, 1983

By Russell R. McLellan

The Tertiary channel gravel deposits in northern California were selected Or detailed investigation by the U. S. Bureau of Mines as part of a national program to locate potential sources of gold that might be developed rapidly by large-scale mining operations. Five bureau research centers representing mining and metallurgy subsystems coordinated their efforts in a team operation to identify and investigate possible solutions to the problem area, that long have discouraged the resumption of large-scale mining in the deposits. This report summarizes the individual investigations, conclusions and recommendations conducted and prepared by all mining subsystems research groups after the completion of two years of field work at the deposits on San Juan Ridge in Nevada County, California. The studies indicate that modern mining technology can cope with the environmental problems that closed the immense hydraulic mines in 1,884. however, they also indicate that mining can be conducted with only marginal profits its unless the price of gold remains substantially above $70 per ounce or unless sufficient by-products can be recovered and sold to place the average value per cubic yard of gravel into a positive commercial range. The by-product potential of the Tertiary gravels remains to be investigated in more detail.

Jan 1, 2012

By Thomas M. Kohler, Gerald L. Finfinger, Gregory M. Molinda

The Bureau of Mines has completed an investigation of the effectiveness of methane drainage in the Lower Sunnyside Coalbed at Kaiser Steel Corp.'s Sunnyside No. 1 Mine in Utah. Most of the previous at- tempts to drain methane gas using long horizontal holes were conducted in the Eastern Coal Province. From the high degree of success realized in these efforts and the large body of knowledge gained from associated research, it seemed natural to extend the technology to western coalfields. Previous work had indicated that properties affecting gas drainage were variable in the Sunnyside Coalbed. In an attempt to characterize these properties, four degasification holes were drilled from the out- side entries of an advancing section. The holes were drilled to lengths of 780, 1,680, 1,315, and 1,047 ft and produced initial flow rates of 50,000, 180,000, 340,000, and 240,000 f t3/d, respectively. A total of over 300 million f t3 of commercial-quality gas has been removed from the Sunnyside Coalbed. The four holes have reduced face emissions by 78 pct.

Jan 1, 1986