Search Documents

By Albert L. Toenges, Louis A. Turnbull, Alonzo W. Quinn, J. M. Schopf, Arthur Neale, R. F. Abernethy

"INTRODUCTION The fuel requirements for industrial and domestic consumers in New England, in normal times, are supplied almost entirely by fuel oil, anthracite, and bituminous coal. A shortage of these fuels occurred during the war. This shortage was caused by (1) The diversion of oil to military uses; (2) the use of railroad and boat facilities that ordinarily would transport coal for the transportation of war materiel; (3) the inability of coal mines to apply the increased demand for coal which resulted from the conversion from oil to coal by domestic and industrial consumers; and (4) the increased demand of war industries for coal. Because of this critical fuel situation, an investiga¬tion was made of possible sources of fuel nearer to points of consumption in New England. Meta-anthracite, which is a satisfactory fuel for some purposes, had been mined in Massachusetts and Rhode Island many years ago. However, the introduction of freer-burning anthracite and bituminous coal into New England markets resulted in the abandonment of these mines.The coal mined in the vicinity of Portsmouth on Aquidneck Island, Newport County, R. I., had been used successfully for smelting copper ore and for fuel. It is reported that this coal is less graphitic than the material mined at Cranston near Providence, R. I. The coal is meta-anthracite and does not burn freely. However, improved equipment for burning coal has been developed, and if minable reserves of meta-anthracite should be found, methods of burning it probably could be devised.The purpose of this investigation was to determine sources of additional fuel. Since meta-anthracite mined at Portsmouth had been used with some success, an investigation was undertaken to determine the characteristics and continuity of the beds in this area."

Apr 1, 1948

By L. C. IlsLey, M. W. Von Bernewitz

"Introduction.Several hundred thousand open lights are daily carried in coal mines of the United States, each lamp being a menace to life and property through fire or explosion. They have been responsible for many disasters in the past, and will be again. Flame safety lamps have been available for over a hundred years, but during the last ten years safe and practical electric lamps have been perfected. These have eliminated many of the flame safety lamps, and in a few mines have replaced open flame lamps. But there are still more than twice as many open lamps as electric lamps in our mines, and the open lamps should be discarded in favor of an approved type of electric lamp. There are several electric miners' lamps which have been approved by the Bureau of Mines for safety and efficiency, give good light, and are easily maintained and carried, some flame safety lamps will always be used, hut mostly for detecting gas; although they might be supplanted if some simple, reliable, and cheap gas detector were developed.Explosion Hazards from Open Lights.An open light and gas*** constitute a vicious hazard; while if there be coal dust present in the vicinity the consequences are multiplied many times. An open light and black blasting powder also constitute an explosion hazard, vividly attested by several serious disasters."

Jan 1, 1924

By J. L. Holman

The Bureau of Mines is conducting research to recover strategic and critical metals such as Ni, Co, and Cr from mixed contaminated super-alloy scrap. One approach being studied involves melt refining of superalloy scrap to produce anodes for electrolytic deposition of Ni-Co alloy. This melt refining of superalloy turnings is described based on melt-oxidation and oxidation-carburization experiments, using roasted superalloy grinding sludge to supply the 0 needed to oxidize Cr and other readily oxidized elements to the slag. Controlled melt-carburization subsequent to oxidation improved the metal phase recovery of Ni and Co to well over 90 pct and decreased electrolytic solubility of Cr, Mo, and W by carbide formation. Electrolytic refining experiments were conducted using a controlled-potential mode (preset cathode potential). Data show effects of Fe and Cr impurities, cation concentration, electrolyte pH, S04-Cl electrolyte ratio, temperature, cathode potential, and cation-selective membrane use on current efficiency, current density, and deposit composition. Disposition of Ni, Co, Cr, MO, W, and Fe is compared for melt-oxidized versus oxidized-plus-carburized anodes. Deposits containing >97 pct Ni + Co (major impurity Fe) have been routinely obtained from scrap anodes. Research is continuing to improve deposit quality in sustained deposition and to recover Cr and other metals from refining slags and anode sludges.

Jan 1, 1986

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. roof drill. The instructions are based upon two actual installations: one made in a mine on roof drill, model 300, and one in the factory. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other roof drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other roof drills and can determine any necessary modifications if they are not.

Jan 1, 1973

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage-, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation With the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects. The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry Missouri School of Mines and Metallurgy, and. Will H. Coghill., supervising engineer of the ore dressing section of the United States Bureau of Mines.

Jan 1, 1932

By James F. Neill, O&apos

Brown iron ore resources in Barbour, Butler, Crenshaw, and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama. The aggregate footage drilled was 18,010 linear feet. When developed, reserves of 12,664,000 long tons of crude ore were indicated, containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet. Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons. Beneficiation of samples by simulated log washing and use of a 118-inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese. Screen-test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size. While an indicated 2,198,000 dry long tons of usable iron ore can be recovered, sink-and-float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing. However, applicable commercial processes have not been demonstrated.

Jan 1, 1965

As part of its regular program to provide timely information on domestic mineral commodities, the Bureau of Mines conducted an engineering appraisal of more than 1,300 lode and placer gold deposits in the United States to deter-mine their gold production potential. While these deposits were estimated to contain over 400 million ounces of gold, only 9 million ounces, or slightly more than 2 percent, was found to be producible at $35 per ounce under prevailing mining and metallurgical technologies. The study revealed that any significant increase in available gold in the United States is most likely to come from the discovery of new sources, intensive exploration and development of the more promising known mineralized areas, and development of new or improved mining and metallurgical techniques.

Jan 1, 1967

By M. R. Geer, H. F. Yancey

"INTRODUCTION With the advent of war in 1941, military operations in Alaska were enlarged on such a scale that the demand for coal in the Territory more than doubled. Coal was needed urgently for heating forts and other military establishments, for use on large construction projects, and for handling the greatly increased volume of traffic on the Alaska Railroad. -The additional tonnage required, estimated at perhaps 250,000 tons per year, probably could have been supplied by the United States, but shipping space between Pacific Coast ports and Alaska was already overburdened with military supplies and construction materials. Moreover, although of only secondary importance in wartime, the cost of coal shipped into the Territory is reported to have been as high as $40 per ton. The alternative to importing coal was, of course, to increase the Production of the Alaska mines.Production of coal in Alaska reached, 350,000 tons in 1944, or more than double the prewar' output. The responsibility for increasing coal production was assumed largely by the Army, A Coal Commission attached to the Alaska Department arranged financial assistance for some mining operations, aided the operators in producing equipment for mechanization, and provided most of the labor necessary to operate the mines. The Bureau of Mines contributed to the program in several ways. First, exploration by the Bureau in the Moose Creek district revealed a substantial tonnage of coal of better grade than any currently mined in the Territory, 4/ and drilling in the Broad Pass district, where a mine to supply coal for the army had been started, revealed that the reserves were far less than had been supposed; this operation was abandoned. Second, coal-preparation practices were studied, and recommendations for improvements made, at two of the operating mines at which the quality of the coal makes preparation a factor of vital importance. Some of the information obtained in these studies forms the basis for the present report."

Jan 1, 1946

By C. J. Chindgren

A refractory-lined, garage-type automobile incinerator with a natural gas afterburner for air pollution control was cooperatively constructed and tested by the Bureau of Mines and the Wasatch Metal & Salvage Co. in Salt Lake City, Utah. The incinerator is capable of relatively smokeless burning of 32 to 60 cars per day, dependent on the degree to which the cars are stripped prior to incineration. Preliminary burning campaigns indicate the cost of incineration to be approximately $2.75 per car.

Jan 1, 1970

By B. W. Gandrud

In July 1948, the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and mine operators, published Report of Investigations 4306, "A Combination Cleaning and Dewatering Process for Treating Fine 'Sizes of Coal, Preliminary Report In this report a new process, referred to as kerosene flotation; was described, and results of experimental work with the process Previous to the fall of 1947 were given, The contents of the report. were summarized on pages 19 and 20' as follows: In coal-preparation plants using wet methods of cleaning, the most difficult problem is the cleaning and dewatering of the "fines" from about 10-Mesh to 0. A combination proceed is now under investigation that shows promise of practically and feasibly solving this problem. The process is similar to froth flotation, but a generous quantity of kerosene is used as one of the reagents, and the feed is from approximately 10-mesh to 0 considerably coarser than the usual froth flotation feed. The kerosene and the coarseness of the reed result in a floated product that, under certain circumstances, can be dewatered satisfactorily by a simple process of mechanical squeezing, Squeezing is accomplished by means of an ordinary conveying' Auger-and trough assembly with a section of pipe easing at the outer end of the trough. The bottom of the trough and. casing is fitted with wedge-wire sections to permit escape of the water freed by the squeezing action of the auger. On account of the important role of the kerosene, the process has been referred to in this report as kerosene flotation. Up to now, the investigative work has been divided about evenly between the laboratory and commercial plants. Nearly all of the work has been done on sludges containing the solids from the underflow of dewatering screens. A few runs have been made on 10-mesh to 0: fines from raw coal, but in some of those runs the dewatering mechanism, failed to function.

Jan 1, 1950

By Martin H. Stanczyk, I. L. Feld

Continuous open - circuit attrition grinding of a coarse commercial kaolin to produce paper - coating clay , which must have a particle size analysis of 70 percent or more minus 2 - micron equivalent spherical diameter ( esd ) , was studied by the Bureau . The coarse clay , containing about 11 percent minus 2 -micron esd material , was ground in a 10 - inch- diameter attrition grinder using continuous single- and multiple - stage grinding circuits . The clay feed rates varied from 10 to 480 pounds per hour . In some tests , the influence of varying loads of sand grinding media on particle size reduction was studied . Batch grinding tests also were made for comparative purposes . Multiple- stage grinding gave better results than single - stage treatment when equivalent raw clay feed rates were used . In the best test made , a product containing about 80 percent minus 2 - micron esd material was obtained when grinding 60 pounds of raw clay per hour using a three - stage grinding circuit . Power consumption in the test was about 318 kilowatt -hours per ton of clay treated or 475 kilowatt - hours per ton of minus 2 - micron esd material produced .

Jan 1, 1963

By William H. Lesser

Never before have mine managers in the anthracite region of Pennsylvania been so seriously concerned about the rising cost of pumping mine water. Many of them know that future pumping charges may affect their operating profits adversely to an extent that will make it necessary to abandon some mines. Increased pumping charges in the anthracite industry are currently comparable in importance with higher mining costs; in fact, profitable operation of some mines depends not only upon the cost of mining coal but also upon whether they can be kept free from water at reasonable cost. Pumping charges are relatively low during the early development of a mine, but they increase rapidly as development progresses. Numerous crop falls, strippings, and. abandoned adjacent properties contribute unfavorably to the volume of water produced during mining. The foregoing conditions and the existence of large underground pools below existing mining levels present water problems of such magnitude and cost that some mine owners cannot continue to operate profitably.

Jan 1, 1950

By Ben E. Lindsly

The study of "bottom-hole samples follows in natural sequence the study of samples obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1930, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs.. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, That physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing Tells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental data were obtained in the study of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at higher pressure, and later became mixed with the original undissolved gas.

Jan 1, 1933

By R. V. Ramani, R. Bhaskar

"One of the primary means of control of health hazards from respirable contaminants in mine atmospheres is through design and operation of mines to meet mine health and safety regulations and recommended practices. A U.S. National Academy of Sciences study concluded that for significant progress in coal mine dust control, research should be directed more toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust. Theoretical and experimental studies on transport of dust · in mine airways, particularly coordinated efforts to validate theory with practice, are scarce. Some empirical models, developed on the basis of experimental data, are available but these models cannot be applied to new conditions. The purpose of this paper is to present the results of theoretical and experimental studies on the transport and deposition of dust in mine airways. This study is a part of an ongoing research project in the Generic Mineral Technology Center on Respirable Dust.In the paper, the assumptions of the modeling phase of the project and the development of a convectiondiffusion equation for dust transport in mine airways are outlined. The important aspect of the modeling effort is the capture of the deposition phenomenon. The experiments performed under controlled conditions in a typical mine airway, as well as under normal mine operating conditions, are discussed. The comparison of the model predictions with experimental results are made to identify critical areas of agreements and deviations. The implications of the findings and areas for further research and development are presented."

Jan 1, 1990

By Kathleen M. Kowalski

In emergency management, the effects of stress on the performance of emergency personnel, typically have been ignored or regarded as too enigmatic to quantify. This paper discusses the concept of Critical Incident Stress in responders to emergencies. It presents the rationale for considering stress as a significant factor in the management of emergencies. It is proposed that Critical Incident Stress Debriefing in a disaster can improve the effectiveness of response teams on site, their turnaround time on site, and post-disaster time off the job. Critical Incident Stress intervention also can mitigate potential deleterious emotional effects associated with emergency work. This paper, prepared by a U.S. Bureau of Mines researcher, offers some ideas to the mining industry in general, to mine rescue team trainers, and to developers of program simulations on the specific issue of how people, time, materials and space may be factored into a plan for emergency management. The impact of stress on emergency workers is, presented as a missing component in present emergency management models.

By William J. Campbell

This report describes a Bureau of Mines study undertaken to determine the applications and limitations of solution techniques as a general method of fluorescent X-ray spectrographic analysis. Systematic errors due to variations in particle size, surface preparation, and sample inhomogeneity are eliminated by the use of solutions. The range of applicability of fluorescent X-ray spectrography is increased in two ways: (1) Samples in the form of wire, filings, turnings, etc., can be analyzed as solutions, and (2) samples submitted as solutions can be analyzed as received 0 The lower limit of detectability varies from 0.14 gram per liter for sulfur, atomic number 16, to 0.0015 gram per liter for strontium, atomic number 38. Most elements have limits of detectability between 0.02 and 0.002 gram per liter.

Jan 1, 1959

By C. W. Schultz

The vapor pressure of manganese in equilibrium with a series of liquid iron-manganese alloys was determined by the carrier gas method over a broad range of alloy composition. From these data the activities of manganese in the iron-manganese system were calculated. The system appears to be ideal.

Jan 1, 1966

By Paul M. Tyler

One by one new metals come to share the burden of modern industry. Long before the Christian era potters and glass workers employed fine and costly blue pigments that contained cobalt. Cobalt blue class has been found in the tombs of the Egyptians and in the ruins of Troy, and many of the colors used by the ancient Greeks and Romans contained cobalt. The ancients, however, were apparently unaware that the colors they used were caused by cobalt, and it was not until late in the 17th century that the existence of the element was recognized, Writers in the Middle Ages referred to "cobalos" as an evil spirit that haunted mines and caused trouble to the miners. Subsequently the German worms "Kobold," meaning goblin, came to be applied to any baffling mineral and particularly to minerals that resembled ores but failed to yield metal when smelted. Even to-day there is something of an air of mystery about cobalt, and a medieval cloak of secrecy still surrounds many of the metallurgical processes employed in its production. "Zaffre" was mentioned about the middle of the sixteenth century by Biringuccio, and in 1735 the metal war, first prepared by G. Brandt. To preparation of cobalt compounds, however, must have been carried on in at least a small way ever since the opening of the silver-cobalt deposits of Schneeberg in 1470. By 1790 there were 25 works engaged in the industry, rust of them located in Saxony, but the total output of these works probably did not exceed 300 tone of cobalt annually, mostly in the fore of smalt. The smalt which contained approximately 6 per cent cobalt was sold in Venice in 1520 at about 16 cents a pound. A few refineries in Holland supplied the Irish linen trade, contributed a farce amount to the Dutch linen industries, and alto provided smaller quantities for the manufactuer of litmus in Holland. A complete description of the early [histor,] of the cobalt industry in Saxony, is given by Mickle in the Deport of the Bureau of Mines of Ontario, vol. 19, 1913, pt. 2, pp. 234-251.

Jan 1, 1930

By Earl R. McMillan

"Coal washing commands the thoughtful attention of a steadily incre in number of people. Clean coal is not merely a luxury but is rapidly becoming a necessity in some industrial operations.Coal seams in the Northeast are rarely free from ""bone"" and shale or clay partings which vary from a fraction of an inch to several feet in thickness. Nearly all of the coal measures are folded and faulted, the coal seams dip at various angles, and in some cases are badly broken. In mining these seams fragments of the roof and floor, as well as partings of impur-ities within the seams, unavoidably become mixed with the coal, so that the raw coal as it comes to the surface often contains as much as 50 per cent, by weight of waste.At the Bureau of Mines experiment station at Seattle, the washing of this coal in order to improve it for commercial use has been studied. Since the process of coal-washing depends upon differences in specific gravity between the clean coal and, its associated impurities, the first problem undertaken was that of determining the specific gravity of the clean coal and of each parting of impurity contained in a large number of representative seams.It was found that the freshly-mined coal is practically saturated with water, this being observed in determining the effect of moisture content upon the specific gravity of the coal particles, selected from samples of coal varying from low-grade subbituminous up to semianthracite, all of which are found in the State of Washington. The specific gravity values determined for the cleanest particles varied from 1.28 to 1.35; in general, the higher the rank of the coal the hither the specific gravity."

Nov 1, 1920

By W. J. Fene

The lowest number of fatalities from coal-mine explosions in the United States in any year since records have been kept was the total of 8 in 1949 and again in 1950. Even incomplete records as far back as 1870 reveal a larger annual loss of life from explosions. From 1890 to 1948 the lowest annual loss was 32 in 1946. A smaller total of 15 fatalities was reported in 1952. Figure 1 shows the total yearly loss of life from explosions in all coal mines since 1880. Those in anthracite mines alone are shown by the shaded area. The erratic variation of the chart line shows the difficulties that have confronted the industry in the struggle to control and eliminate mine explosions. Potential hazards have existed in marry mines without realization that only a small change in conditions could initiate a disaster. Many disasters causing great loss of life occurred in mines that had been regularly operated without incident for long periods. Although the number of coal-mine explosions causing great lose of life has been kept down in recent years, the exceptions still make the record anything but satis¬factory. There have been almost no widespread explosions for several years, but in a few instances many lives were lost from afterdamp. Although the violence and spread of mine explosions may be controlled, the loss of life may be heavy if many of the men happen to be in the path of the smoke and gases. For these reasons, the strictest controls must be maintained to eliminate all factors that might combine to cause even a small ignition of gas or dust.

Jan 1, 1953