Search Documents

By Oliver A. Dibble

This paper it one of a series being prepared for and published by the United States Bureau of Mines, describing mining methods and costs at clay pits throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The open-pit recovery of clay for cement plants is a comparatively simple operation in comparison with underground mining of clays; nevertheless, it represents an appreciable factor in the cost of cement manufacture. The following report deals specifically with the methods employed by the Aetna Portland Cement Co., which operates cement mills at Fenton and Bay City, Mich., in recovering clay from their pit at Corunna, Mich., on the Grand Trunk Western Railway.

Jan 1, 1932

By F. R. Cattoir, R. E. Cumings

Columbium metal was electrorefined in a fused - salt electrolyte . Excellent results were obtained in lowering the impurity content in a 94 - percent columbium anode feed material to produce a 99.8- percent - pure metal . The reductions of the major impurities follow : Oxygen from 19,800 to 500 ppm , carbon from 9,700 to 25 ppm , iron from 9,200 to 630 ppm , nitrogen from 2,100 to 90 ppm , and silicon from 750 ppm to not detected . Columbium with a purity of 99.9 percent was produced from 99.5- and 99.8 - percent grades of columbium. The investigation was devoted to the evaluation of a fused - fluoride - salt electrolyte ( KF - NaF- K₂ CbF, ) for electrorefining columbium. The effects of the columbium concentration and the voltage upon the product's purity were investigated . The effect on the cathode current efficiency of ampere - hours of deposition and the formation of a dual valence state of the columbium was also investigated .

Jan 1, 1964

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry - reduced personnel, decreased active field development, and curtailed production - have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period. Fatality statistics for 1932 show that the drilling and producing, pipe line and transportation, and refining and natural gasoline divisions of the industry had fewer accidents in 1932 than in 1931, sales and marketing being the only division that showed an increase over 1931. The number of fatalities by divisions for 1931 and 1932, percent of total, and percentages of increase and decrease are given in Table 1.

Jan 1, 1933

By R. F. Stewart

A sedimentation method involving the use of the Palo-Travis apparatus was found satisfactory for rapid determination of the size distribution of coal particles ranging from 10 microns in diameter to those passing an 840-micron opening (20-mesh sieve), The method is most useful for comparing the size distributions of samples of pulverized coal where the actual size of the particles is not required and is applicable to sieve and subsieve sizes of a wide variety of coals and chars that can be wetted and are heavier than water. An analysis, including all calculations, can be completed in 1/2 to 10 hours, depending on the time required for the finely divided coal to settle. A typical analysis requires about an hour, making this a rapid, precise method for routine size-distribution analysis of powdered coals. When used with coal particles smaller than 400 microns, the method is precise within 15 microns for wide variations in test conditions and within 5 microns for identical test conditions. The precision decreases as particle size increases, becoming unsatisfactory for particles larger than 400 microns (40-mesh). For precision within 15 microns, the samples must be equal in weight. Greater precision is obtained with 4-gram samples, but samples as small as l gram may be used.

Jan 1, 1961

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract No. HO395132 to develop and fabricate gas sensors for mining applications. Promising new instruments have been designed, developed, tested and supplied to meet BuMines requirements. These instruments include prototype 1) remote-sensing, diffusion-type CO monitors for mine operation which can be operated in conjunction with a surface computer, 2) control modules for alternate in-mine readout of the remote diffusion type CO monitors, 3) personal CO diffusion-type dosimeters and 4) personal NO diffusion-type dosimeters. In addition, retrofit modifications were made to update and optimize operation of CO and NO2 direct-reading type detectors provided under a previous contract. Studies were conducted to evaluate and demonstrate the availability of stable, portable N02 calibration sources for NO2 instrumentation. The use of selected, commercially available cylinder sources for NO2 instrument calibration were recommended. Additional studies were also conducted to investigate the feasibility of instrumentation for rapidly monitoring CO, NO and NO2 in diesel exhaust.

Jan 1, 1981

Rank the dust knockdown (airborne capture) ability of six different types of water spray nozzles, Approach A fixed quantity of dust is released into a large, closed chamber in a laboratory. Water sprays are turned on inside the chamber and their effectiveness on the dust cloud is evaluated from the rate at which the dust disappears. This method better simulates dust suppression underground than methods tried earlier. The results of the laboratory test were confirmed by conducting tests on a full-scale mod-el continuous miner face where dust levels were measured in the return airway. Results of the Closed Chamber Tests The graph indicates that atomizing nozzles provide the best use of water for dust scrubbing. However, use of these nozzles is limited by their susceptibility to damage and clogging. Hollow-cone nozzles perform almost as well as atomizing nozzles. Test results also indicate that full-cone, venturi-assisted, and flat-fan spray cones are about two-thirds as effective as hollow-cone nozzles. The least effective were venturi nozzles designed for moving air. The most significant advantage of hollow-cone nozzles over other nozzles tested is reduced clogging due to larger orifice size. The hollow-cone nozzle used in the test and depicted by the graph was type BD-3 manufactured by Spraying Systems Co., Wheaton, IL. This nozzle is already used on many continuous miners. Other hollow-cone nozzles of

Jan 1, 1982

By Herbert H. Einstein

The innate variability of natural materials and processes causes uncertainty in the models representing the natural phenomena and uncertainty in estimating the parameters that are used in these models. Reliability analyses, in contrast to the traditional factor of safety approach, are well suited to a rational incorporation of uncertainty in design and exploration decisions. Probabilistic kinetic and kinematic analyses were developed and combined to form reliability analysis methods. With one method the reliability, i.e.) the probability of failure, of an individual 2-plane wedge in a slope can be determined. The other method is aimed at slopes with a single slope parallel set of joints. In each case two approaches were developed, an encompassing one relying on computer codes and a simplified or summary approach relying on charts or pocket calculator computation. A major contribution of these approaches is the treatment of joint persistance. Instead of having to assume a certain persistence, it is now possible to use exploration data on joint geometry and to include the persistence effect rigorously.

Jan 1, 1979

By John Owens, Wayne Howie, Hamid Maleki

After an analysis of the hazards of room-and-pillar retreat mining systems, it became apparent that safety could be significantly improved by considerations of (1) human factors, (2) remotely controlled mobile roof supports (MRS=s), (3) mine layout designs, and (4) ground monitoring systems. Initial studies of the effectiveness of MRS=s focused on their interaction with mine strata and evaluations of suitable measurements for detecting roof stability problems during pillar extraction. These studies indicated that overall stress distributions and strata movement were most influenced by the stiffness of coal-measure rocks and the design of mining layouts. Thus, to improve worker safety, mine layouts should be carefully designed and a pillar extraction method chosen for specific geologic and stress conditions. Pillar failure was often associated with an increase in pressure on the hydraulic gauges of the MRS, and roof failure was often preceded by rapid changes in the rate of roof-floor convergence. These studies led to development of a monitoring system that displays loading rate on an MRS in real time. A major MRS manufacturer cooperated in installing and testing the system on an MRS. New field studies focus on evaluating the performance of the system, measuring roof-floor convergence, and optimizing the safety of MRS operations through proper mine layout design.

Background Carbon monoxide (CO) is an odorless, colorless gas that can cause illness and death by asphyxiation. Although the toxicity of CO is understood, CO exposure can occur from unrecognized sources. On April 2, 2000, a couple and their newborn infant were poisoned by CO migrating through the ground from blasting at a nearby coal strip mine into their home near Kittanning, Armstrong County, PA. They were treated at the hospital and diagnosed with CO poisoning. The infant had a carboxyhemoglobin level of 31%, the father 28%, and the mother 17%. Carboxyhemoglobin is the compound formed in the blood when CO is breathed. Persons not exposed to CO have carboxyhemoglobin levels of 0.3%-0.7%, and cigarette smokers have levels of up to 9%. Following release from the hospital, the family installed a CO detector in the basement of their home with the help of the local fire department. This Technology News briefly describes this incident to help increase awareness of the problem. It is discussed in more detail by Eltschlager et al. [2001]. Figure 1 shows the coal strip mine believed to have generated the CO. The initial suspect for the source of the CO was the furnace in the house. Only later did it become apparent that blasting at the nearby strip mine might be the culprit. A State investigation concluded that CO had migrated approximately 500ft from the blast, through the ground, and into the home. Figure 2 shows the locations and order of blasts at the mine. Initially, the mine did not plan to blast. Overburden generally consisted of weathered shale that could be dug without blasting. However, the mine decided to blast when hard sandstone that could not be dug out was encountered within 3 ft of the coal top. The blasting was intended to break up the sandstone. Blasting was done using bulk ammonium nitrate-fuel oil (ANFO) in 6.25-in holes 25-30 ft deep on a 16-ft by 16-ft pattern, with charge weights ranging from 17 to 170 lb. The closest blast to the home was 430 ft on April 17, 2000. The distance from the home to the blast area on the day when CO was first reported (March 31, 2000) was 500 ft. Twenty blasts were detonated at the mine between March 7, 2000, and April 20,2000. The blaster was careful to prevent fly rock since another home was only 150 ft away and a garage was 50 ft away. The quantity of explosive used in the blasts was sufficient to break the sandstone, but was less than would normally be used to blast overburden. The holes were typically one-third explosive and two-thirds stemming, with powder factors averaging 0.43 lb/yd3. Additionally, the muck was not immediately excavated after each blast. The heavy confinement on the explosive acted to prevent the typical release of blasting fumes into the atmosphere. Instances of CO migrating from blasts into homes have occurred before, but generally the distances involved were under 150 ft. It is believed that the blast design contributed to the confinement of CO in the ground, and discontinuities in the ground strata facilitated migration toward the residence. Upon inspection of the blast pitwall, a regular system of joints was observed. These joints are oriented roughly from the blast pit toward the house (figures 3-4).Blast-generated CO appears to have been driven into the joint system, displacing the air. When the joint system was saturated, the next succeeding blast pushed the CO into an uncased well next to the house (a high level of CO has been measured in the well shortly after a blast). From there, the CO entered the French drain system and then the basement of the house. The joints are vertical cracks through rock layers that occur on a regular spacing (figure 3). They are most common near valley slopes and are caused when valley walls converge as the stream cuts down through the rock layers. Often called hill seams, they roughly parallel the valley walls, but can curve and split, creating a pathway for gas movement (figure 5). These fractures are often encountered when underground mining proceeds close to outcrop. The system of fractures at the Kittanning blast pit was well developed and provided a path for transmission of CO both through the sandstone and up and through the overlying shales. Blasting engineers should be able to distinguish naturally occurring fractures from blast fractures and note the frequency, development, and orientation of the hill seams and their proximity to occupied houses. The limits of transmission of

May 1, 2001

Improve the performance of waterjet nozzles used for water-jet-assisted cutting to optimize rock cutting efficiency. Approach The performance of a longwall shearer equipped for water-jet-assisted cutting was evaluated during an earlier study (Tech News No. 277). Waterjet nozzles were used to direct the solid streams of water that impacted the rock near the tip bits. The maximum water pressure that could be delivered to the nozzles was about 6,000 psi. Due to the "break up" of the solid stream of water, some of this pressure was lost before the water reached the rock. The pressure could have been increased by moving the nozzle closer to the bit tip but) moving the nozzle too close increases the possibility of damage to the nozzle. Study Results A test apparatus was built to measure water pressure at the location of water jet impact (see illustration). The target, a tungsten carbide plate with a 0.013 inch diameter orifice, was placed at the location of water jet impact. A pressure transducer, used to monitor impact water pressure, was positioned under the plate. Water pressure at the nozzle was maintained at 6,000 psi. The distance between the nozzle and target was varied from 2 to 5 inches.

Jan 1, 1988

By Parry. V. F., W. S. Landers

"INTRODUCTION Approximately 1,250,000 tons of 2-1/2-inch and 1-1/2-inch slack, representing over half of the output from 40 to 50 mines, is produced in the Denver region each year. Part of this slack is made by crushing lump, and some of it is rescreened to make pea and modified pea sizes measuring 1-1/2 inches by 2-1/2 inches and 3/4-inch by 1-1/2 inches, round-hole. Modified pea is popular as domestic stoker fuel. Approximately 900,000 tons of slack 0 by 2-1/2 inches, 0 by 1-1/ 2 inches, and 0 by 3/4-inch in size are consumed by industrial plants, the principal consumers being a large power plant and the beet-sugar industry. The power plant uses annually 250,000 to 275,000 tons of pulverized fuel and can pulverize slack of any size, while the sugar factories consume about the same quantity of coal in stokers. The sugar factories store about 110,000 tons of 2-1/2-inch slack under water from January to October, and burn the remainder of their consumption directly during the campaign season from October to December. For this purpose, sugar-factory power plants can use any size of slack, which is recrushed to pass a 3/4- or 1/2-inch screen before burning on chain-grate stokers. About one-third of the 2-1/ 2- inch slack produced in the field is used in smaller industrial plants that employ stokers.Certain factors affect the utilization of 2-1/2-inch slack in the Denver region. The increasing production of hydroelectric power has reduced the consumption of coal at power plants slightly. If more hydropower is generated, the trend of consumption of slack might be downward, unless industrial activity offsets this greater output. Rapid increase in number of domestic stokers during recent years has necessitated preparation of greater quantities of stoker coal, with the result that more lump is crushed, and preparation facilities are changed. At present about 19 percent of the coal produced is crushed to meet the constant demand for industrial fuel as well as the increasing but variable demand for the small domestic stoker sizes. The quantity crushed has increased 12 percent during the last 6 years. These factors are shifting constantly. The trend toward the use of clean and smaller sizes for domestic stokers gives a slack having a larger proportion of fines. In future, even greater quantities of small stoker coal probably will be prepared, and the resulting greater quantities of small slack will have to be used for industrial purposes."

Aug 1, 1942

By A. B. Hooker, P. G. Guest, E. J. Gleim

"From time to time the United States Bureau of Mines has received reports of gas explosions alleged to have been caused by correctly assembled flame safety lamps. In most of the mines where the explosions occurred the lamp was in use at a working face where the velocity of the ventilating current would be relatively low. The inference has been that the lamp was correctly assembled but that the gauze became sufficiently overheated to ignite the surrounding atmosphere.As part of its routine investigation of flame safety lamps the Bureau of Mines subjects each lamp to a test in still and moving atmospheres to determine its safety. Heretofore, as long as the lam, successfully passed this and other tests no determinations as to the margin between success and failure were made; hence, in attempting to answer inquiries concerning the reported explosions it was found desirable to be able to give actual gauze temperatures as a measure of the comparative safety of lamps under various conditions. The previous laboratory tests of flame lamps in still mixtures were made in a chamber or ""gallery"" of relatively small volume where the lamps might have been subject more or less to the smothering effect of the combustion products. It was therefore decided to make a special series of tests to obtain the gauze temperatures of both bonneted and unbonneted lamps in still and low velocity mixtures, using a larger gallery to offset any smothering effect.These tests are believed to represent the first attempt at measuring gauze temperatures by means of themocouples. The results will not only be of interest but will also be helpful to many in determining the status of flame safety lamps relative to gas ignitions in mines."

Feb 1, 1929

By Maria I. De Rosa

During 1990-2001, a total of 518 fires occurred in all metal/ nonmetal mining categories; 296 of those fires caused 308 injuries and 4 fatalities. Surface operations had the most fires and the highest injury risk rate values. Forty-five fires destroyed or heavily damaged facilities and equipment (including 19 pieces of mobile equipment) because of failure of firefighting methods, late fire detection, undetected fires, or fire size. In the future, many of these fires and injuries might be prevented or detected and extinguished at their earliest stage by improving current fire safety procedures, adopting existing/ improved fire detection and suppression technologies, and/or developing new technologies. Several strategies for reducing and/or preventing the number of fires and fire injuries follow. I. Increase vigilance, improve safety procedures, and develop new technologies in order to prevent fires and injuries caused by fame cutting and welding operations. 2. Improve equipment hydraulic/fuel/electrical systems inspection programs; adopt fire-resistant hydraulic fluids and electrically powered motors for use in underground mines; develop new technologies (equipment/cab rapid fire detection/ prevention/suppression systems, emergency line drainage systems, and fire barriers); adopt an optimal ground level location for the activation of emergency systems; improve operator's fire preparedness training programs; and develop effective and rapid local firefighting response capabilities. 3. Adopt existing/improved systems for continuous and early detection of combustion gases and smoke along beltlines. 4. Adopt existing/improved technologies for monitoring equipment (beltlines) operational functions. 5. Increase vigilance and adopt improved safety procedures for handling f amenable liquids and refueling fuel in the vicinity of heat sources.

Jan 1, 2004

Reduce permanent hearing losses to bulldozer operators. Approach Two types of noise control packages have been developed, that can be readily fabricated and installed into bulldozers by mine personnel. How It Works Both of the noise control packages reduce the noise exposure of the operator by two techniques, blocking the noise paths or absorbing the sound before it reaches the operator. Both airborne noise paths and noise paths through the machine are blocked. One noise control package is designed for bulldozers having ROPS (Roll Over Protection System), but no cab. The other package is designed for bulldozers having ROPS

Jan 1, 1981

By W. A. Young

Bull Lake is one of several saline lakes situated a few miles north of Rawlins, Carbon County, Wyo. (figs. and 2).. The Bureau of Mines conducted preliminary investigations of sodium sulfate deposits in many of the lakes and performed detailed work on Bull Lake. This investigation consisted of drilling 11 vertical holes through salt beds using diamond core bits and Iwan-type auger bits. Bull Lake lies in a shallow, closed depression in loosely consolidated sand. The salt beds, ranging in thickness from 2.5 to 26 feet, occur above a thick bed of shale of upper Cretaceous age. The salts appear to have been deposited in the lake from surface and subsurface drainage. The source of salt is undoubtedly the enclosing sedimentary rock's exposed to the west of the basin. Sodium sulfate in the deposits probably is present as mirabilite or Glauber salt (Na2SO4-10H2O). Chief impurities in the deposits arc mud and sand. Other soluble salts present average approximately 1 percent combined. Cores from the 11 holes were analyzed in the Bureau of Mines laboratories at Salt Lake City. Drilling totaled 512 feet. Results of analyses are given in the appendix.

Jan 1, 1951

By Hugo E. Camargo

Noise Induced Hearing Loss is the most common occupational disease in the U.S. and of paramount importance in the mining industry. According to data for 2006 from the Mine Safety and Health Administration (MSHA), Continuous Miner operators accounted for 30.2% of underground mining equipment operators with noise doses exceeding the Permissible Exposure Limit (PEL). This figure becomes more significant considering that 49% of the 2006 national underground coal production was extracted using continuous mining methods. Thus, there is a clear need to reduce the sound radiated by Continuous Mining Machines. The first step towards efficient noise control of a Continuous Mining Machine requires identification of the various noise sources under controlled operating conditions. To this end, a 42-microphone phased array was used in conjunction with 4 reference microphones to sample the acoustic field of a machine in the Hemi-anechoic chamber of the Pittsburgh Research Laboratory. These data were processed using a frequency-domain beamforming algorithm to obtain acoustic maps of 5 sides of the machine. The focus of the test was on the conveyor noise since previous studies showed that operation of the conveyor is the most important contributor to the sound radiated by the machine. From the acoustic maps, the following potential areas for noise control were identified, and included: chain-tail-roller interaction, chain flight tip-side board interaction, and chain-upper deck interaction.

Jan 1, 2008

This report summarizes the work performed and results achieved on the above contract from October 18, 1971 through July 14, 1972 under Phase II, Task 1: Detailed Design of Prototype and Task 3: Supporting Experimental Investigation. Operation and Service Manuals resulting from Task 3 are submitted under separate cover as are detailed design drawings and specifications, prepared under Task 1. Both items accompany this report. This report also includes (A) an estimate of the cost of construction, (B) a description covering the use of the equipment, and (C) a proposed test plan to demonstrate performance of the equipment in both the laboratory and a mine.

Jan 1, 1972

By Frank G. Horino

This report describes an instrument designed by the Bureau of Mines for quantitatively identifying texture of rock surfaces produced by grinding or extremely rough surfaces beyond the range of commercial surface measuring instruments. The transducer for the instrument is a linear variable differential transformer that converts mechanical motion caused by surface roughness, waviness, and lay to an electrical output. The electrical output is recorded graphically as an X-Y plot of the line traversed on the rock surface. Details of the synthesized device and its calibration are given. The sensitivity of the unit is 2 percent of the scale setting of the amplifier. The horizontal scale is adaptable from ¼ inch to 15 inches of specimen length with a sensitivity of 0.01 inch if a 10 to 1 magnification is used and 0.1 inch if a 1 to 1 magnification is used.

Jan 1, 1968

By H. B. Brunot

One of the many difficult problems that confront the present day coal-mine operator is the safeguarding of his employees and property from disasters such as fires, explosions, squeezes, and inundations. Those operators having gaseous or ev en dusty mines have a double responsibility resting upon them in this respect. The introduction of electrical machinery and appera tus in mining operations has been very rapid, and at the present time it is difficult to mention any kind of mining work in which electrical machinery is not used. This extended introduc- tion of electrical equipment has added not a little to the mine operators' safety problem, and it is the desire of the United States Bureau of Mines to aid the mine operator, and the inspection departments having jurisdiction, in solving their electrical safety problems. With this idea in mind, the Bureau has prepared and published schedules setting forth the qualities it considers essential to the safety of various classes of mining equipment, and the conditions under which it will test and give the stamp of its approval to satisfactory designs. Portable electric lamps of the permissible* type are almost universally used in gaseous mines, but the use of permissible electrical machinery has not been so widespread. Until recently the Bureau had issued approvals for only one class. of machinery involving the use of electric motors that is, permissible coal- cutting machines. However, the day is undoubtedly not far distant when the operator, who so desires, will be able to obtain a permissible room hoist, pump, or coal- loading outfit. During the year 1921 the first of a growing list of storage-battery locomotive approvals was granted by the Bureau, and it is with considerable satis- faction that the Bureau how announces the approval of a third class of motor equip- "merit- namely, slectric drills.

Jan 1, 1923

By J. L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former US Bureau of Mines (USBM) to engineer techniques that will reduce the hazards in the mining workplace associated with coal bumps. Recent research focused on a longwall coal mine in Utah with overburden greater than 750 m (2,500 ft) containing several massive sandstone units. The primary field instrumentation at the site was three-dimensional, full waveform, autonomous microseismic arrays placed underground and on the surface in order to surround the active multi-panel longwall district. The purpose of these arrays was to help investigate the strata mechanics associated with the redistribution of stress and the associated gob formation of the longwall. Specifically, the seismic arrays were used to determine the timing and location of the failure in the strata surrounding the active mining. Overall 13,000 seismic events were detected and located with on-site processing during the five months the panel was being mined, including a magnitude (ML) 4.2 event. Of these, a smaller subset of 5,000 well-located events was selected during post-processing to form a consistent data set for analysis in this paper. From this data set, it was observed that the seismic events generally occurred in advance of the longwall face, both above and below the panel, consistent with failure of the strata in the forward stress abutment zone. Also, the occurrence of the ML 4.2 seismic event within 150-180 m (500-600 ft) of a deep cover longwall face with no associated bump caused a re-evaluation of the nature of the connection between seismic activity and coal bumps.

Jan 1, 2002