Search Documents

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By G. S. McCaa

Rock-dusting is an. effective means of preventing coal-dust from propagating an explosion in a coal mine, but it will not prevent gas from igniting-explosively and with much attendant damage locally. Ventilation must therefore be effective at all times, regardless of the employment of other explosion-prevention methods, if gas explosions are to be avoided. This paper describes a gas explosion which occurred in as bituminous mine that was well rock-dusted at the point of ignition and which exemplifies the value of rock-dusting, the necessity of maintaining effective ventilation, and the need of permissible rock-dusting machines receiving power from a permissible locomotive. Description of Explosion The mine in which this explosion occurred is developed on a panel system in a practically level seam; the panel entries are driven in pairs, and the air current intakes on the right entry and returns on the left entry. Near the mouth of the intake a door is placed to control the ventilation; board stoppings are placed in crosscuts, except the second from the face, in which a brattice cloth curtain is hung, the last crosscut is left open and line brattices conduct the air current from the last crosscut to the faces. In No. 7 entry the last cross-cut was 152 feet from the face, the line brattice being within 38 feet of this face, and the second crosscut was 250 feet outby the face of the back entry or return. Seven days prior to the explosion the intake and return entries were rock-dusted to within 38 feet of the face, and as the entry had advanced during the week, the rock-dusting was to be extended.

Jan 1, 1929

By J. W. Miller

From 1889, when the first railroad shipments of coal were made from McDowell County, W. Va., until today, the coals produced from the New River and Pocahontas groups have had a good reputation as premium low-volatile coals. Although there has been a large production from the Pocahontas No. 3 and. Pocahontas No. 4 beds, considerable reserves remain. This Bureau of Mines publication is one of a series appraising the Nation's coking-coal reserves by presenting data on the basis of which the practicability of upgrading marginal deposits to metallurgical standards can be determined. This study of the preparation characteristics of McDowell County coals is the second of the series to be undertaken in West Virginia. The Pocahontas No. 3 and No, 4 beds have not been included because their washing characteristics are well known.

Jan 1, 1954

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) spectroscopy has been employed to· examine the role of tetraperoxochromate( V) ions (Cro:-) and other Cr(V) species in the generation of hydroxyl (OH) radicals in the reaction of Cr(VI) with H2O 2 in biological media. In contrast to earlier suggestions, the present ESR studies using crystalline K3CrO8 as a source of Cro:- show that decomposition of Cro:- in water or in H2O 2 does not generate significant amounts of OH radicals. Addition of NADH to a solution containing Cro:- yields a Cr(V)-NADH complex, which readily reacts with H2O 2 to generate OH radicals. Similar results obtained from several other biological reductants, including vitamin B2 , indicate that a vacant coordination site on a Cr(V) complex facilitates its reaction with H2O 2 to generate ""OH radicals. We thus suggest that in biological media, reaction [3] instead of [1] or [2] is the major pathway for the OH radical generation: While the carcinogenic potential of Cr(Vl)-based compounds has been well established via epidemiologic and animal studies (1), the underlying biochemical mechanism is still not well understood (2). In a recent development, however, Kawanishi et al. (3) have reported that hydroxyl (OH)2 radicals might be the key species in the mechanism of Cr(VI) toxicity. As to the mechanism of the ""OH radical formation they suggest that Cr(VI) reacts with cellular hydrogen peroxide (H2O 2) to form the tetraperoxochromate(V) (Crog-) ions, which decompose to produce hydroxyl radicals. It was also suggested (3) that the ""OH radicals thus produced cause genotoxicity via DNA base modification and deoxyribose phosphate backbone alterations. More recently Aiyar et al. (4) reported the detection of OH radicals in the reaction of Cr(VI) with H2O 2 in biological media, including the reaction of ""OH radicals with deoxyguanosine to generate 8-hydroxydeoxyguanosine adducts, confirming that ""OH radicals could indeed play a significant role in the mechanism of Cr(VI) toxicity. However, the mechanism for the ""OH generation was not clarified, although the role of Crog- ions as possible precursors was mentioned, somewhat along the lines suggested by Kawanishi et al. (3). The possibility of the participation of Crog- in the ""OH generation has also been indicated by Sugiyama et al. (5), since they mention that vitamin B2 enhances the formation of""OH radicals in the reaction of Cr(VI) with H2O 2 because of the generation of Crog- in the reaction."

Jan 1, 1990

By David A. Hill, James R. Wait

This report contains a summary of analytical research on electromagnetic methods of nondestructive testing of cylindrical conductors. The principal objective is to provide theoretical insight to the operation of electromagnetic sensing of the internal properties of wire ropes that are used extensively in mine hoists. An overall review of past work is also included.

By G. S. Scott

In the course of the investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, some attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rice if the rate of generation of heat exceeds the rate of brat dissipation and will fall if the opposite is the case. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By G. S. Scott

In the course of tire investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, come attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rise if the rate of generation of heat exceeds the rate of heat dissipation and will fall if the opposite is the cane. Factors that affect the rate of generation of heat are:

Jan 1, 1941

Identify specific sources and the relative levels of contribution of various components of longwall shearer operations to the total airborne respirable dust generated during mining. Approach A research investigation was conducted in two phases by the Bureau of Mines at five mine sites to identify specific dust sources and their relative importance during long-wall shearing operations. During phase I of the project the specific longwall mining elements identified for evaluation were: cutting, sumping, tramming, conveying, and moving roof supports. During phase II of the project, two dust sources were evaluated: clearance ring cutters cutting in six-inch web width increments, and loading operations. Investigation Results As a result of dust measurements, the gage cutters were determined to be the major dust-generating source on the shearer. These cutters, at 6-inch web depth, produce three times as much dust per unit volume as is produced at 30 inches full web depth. The following list of averaged values for the mines tested shows that shearer cutting generated averaged dust levels four times as high as those generated by conveying, and approximately five times as high as those generated in moving roof supports.

Jan 1, 1984

By H. K. Kutter

The pressure pulse generated by an underwater spark \vas investigated in relation to its potential use for rock fragmentation. The study established (1) the relation between the peak discharge current and the peak wave pressure; (2) the relationships among the peak wave pressure, the discharge voltage, and the spark gap width; (3) the type and pulse duration of the generated wave; (4) the percentage of energy transmitted in the spark as a function of spark gap width and discharge voltage; and (5) the percentage of energy converted into the pressure wave as a function of gap width and discharge voltage. Spark-generated fractures were studied in two-and three-dimensional rock and plastic specimens. The laboratory results indicated that the pressure pulse generated by an underwater spark is a potential practical tool for rock fragmentation. The paper contains an appendix describing the capacitive pressure gage specially developed for the laboratory tests.

Jan 1, 1969

By S. McGinn, G. Schnakenberg, D. Petrie, A. Bugarski, M. Grenier

As part of the Diesel Emissions Evaluation Program (DEEP) consortium, Noranda Inc. has undertaken a field project to evaluate the overall performance of the latest diesel particulate filter technology (DPF) at its Brunswick Mine in Bathurst, New Brunswick. Performance of the filtration systems is evaluated with respect to their ability to reduce tailpipe emissions and concentrations of diesel particulate matter (DPM) and noxious gases in mine air, efficiency of filter regeneration process, maintenance requirements, reliability, and acceptance. Four different particulate filter systems deployed on heavy production vehicles are subjected to an 18-month field evaluation. Over the evaluation period the vehicles will have accumulated approximately 4000 operating hours in production. This paper presents the results of testing conducted mid way through the 18-month field trials. The 400- meter section of the mine drift at 525-5 sub level, hereinafter referred to as the "isolated zone" was isolated between intake and exhaust fan systems and sealed with bulkheads against leakage. The isolated zone was ventilated at the rate required per CSA Standards and issued by CANMET for the engines tested. Four vehicles, two load-haul-dumps (LHDs) and two trucks, retrofitted with particulate filter systems were tested along with a new identical model LHD and truck equipped with exhaust systems consisting of a catalytic converter (DOC) and muffler. The test vehicles were operated individually inside the isolated zone for approximately 4 hours over simulated production duty cycles. Measurements of ambient concentrations of particulate matter, tailpipe emissions, and engine parameters were performed for each of the tested vehicles. The DPM samples for carbon were collected at the most up- stream end of the isolated zone, at the vehicle next to the operator, and at the most downstream or exhaust end of the isolated zone. The DPM samples were analyzed for total (organic and elemental) carbon using NIOSH Analytical Method 5040. Ambient concentrations of particulate matter at the exhaust end of the zone were also measured using Scanning Mobility Particle Sizer (SMPS), and real time PAH monitor (PAS 2000). Efficiency of the filters was also evaluated on a basis of tailpipe measurements performed using raw exhaust instruments the NanoMet and the UGAS. In addition, relevant engine parameters were obtained using Detroit Diesel Diagnostic Link (DDDL) and from exhaust backpressure and temperature measurements. Results from the tests proved conclusively that diesel particulate filters can significantly reduce the concentrations of air- borne DPM, but not without careful monitoring of both ambient and tailpipe emissions and not without careful attention with respect to maintaining the integrity of the DPF systems.

By Irving Kabik

Chlorates and perchlorates, when mixed with certain reducing materials, may give a detonating explosive of considerable power. Concerning explosive chlorate mixtures, Guttman3/ states that they "have at all times fascinated inventors on account of the large amount of oxygen stored up in potassium chlorate, which can be given off so readily. When Lavoiser and Berthollet tried to make a chlorate powder in a stamp mill in 1788, they made a great show of it, and even two ladies were present. Unfortunately, after a certain amount of pounding the powder exploded and killed an official and the daughter of the Government commissary, who assisted at the experiments.***. It is interesting to observe how the same old mixtures are proposed over and over again with slight alterations only, in order to qualify for a patent. Potassium chlorate with some carbonaceous matter like charcoal, sugar, starch, glycerin, flour, or sometimes a vegetable or mineral oil and the like occurs again and again." Sprengel explosives, in which some of the undesirable sensitivity of the chlorate was minimized by coating the crystals with a liquid reducing agent, received some attention after a patent was issued to Dr. Herman Sprengel in England in 1871.4/ A somewhat similar explosive, known as Rack-a-

Jan 1, 1945

The U.S. Bureau of Mines conducted a laboratory study to determine what effect use of water-jet-assisted cutting has on frictional-ignition suppression. A single bit with a steel tip, installed on a rotating drum, repeatedly made 22-in-long cuts in a block of Berea sandstone. The drum was operated in an enclosure that contained an explosive methane-air mixture. High-pressure front-mounted water jets operating at 2,000 to 5,000 psig and low-pressure rear-mounted sprays operating at 80 psig were used; the number of ignitions that occurred with each type of spray was compared. The rear-mounted spray was more effective for preventing frictional ignitions than the front-mounted water jet.

Jan 1, 1989

By Ben E. Argyle

"The tungsten area in southern Mecklenburg County, Virginia, was studied by the Bureau of Mines during the period August 1944 to March 1945. The explorations were an expansion of the work done by the Bureau in 1943 in the tungsten area of Vance County, North Carolina, which joins Mecklenburg County on the south.3/Outcrops of quartz veins in the area were searched for and examined, and the only Promising showing found (a vein on the Gladys N. Taylor tract) was explored by trenching, test pitting, and diamond drilling (fig. 1).Mecklenburg County, Virginia, is in the southeastern part of the State, bordering on North Carolina,U. S. Highways 1, 15, and 58 traverse the County, and State and County roads provide ready access to most parts of the area.In 1942, Joseph and Richard Hamme discovered tungsten-bearing quartz veins in Vance County, Forth Carolina, and started mining and milling the ore. The first concentrates were shipped in July 1943. In August 1943, the Hamme holdings were acquired by Haile Mines, Inc., who continued the mining operations.The Bureau of Mines began exploratory work in North Carolina in June 1943. Reconnaissance work showed that the mineralized belt extends north-ward into Virginia. The Kimball tract, which joins the Taylor property on the north, was explored in 1943 by trenching and drilling by the R. G. Lassiter interests of Raleigh, Y. C., with disappointing results.The topography of the district is mature and characterized by wide, shallow valleys and low, rounded ridges. The main ridges trend northeast. Most of the area ranges from 300 feet to 400 feet above sea level.The relief apparently is controlled by resistant quartz lenses and the associated hard, silicified zones. The enclosing schists and granites are usually deeply weathered. Consequently, most of the quartz veins are found on the ridges."

Apr 1, 1946

By McHenry Mosier

The diamond-drill method was tried at the site selected for driving a 5- by 6 -foot air shaft at the east end of the Bellefonte mine . This method of sinking consisted , first , of drilling a 5-3/4 -inch-diameter cut hole from the surface , then drilling parallel 1.5 - inch ( EX ) holes around it at appropriate distances for a balanced blasting round . The cut hole was not charged with explosive but served as a relief chamber for the incipient expansion of the ground broken by. blasting the surrounding 1.5 - inch holes . The length of each hole was 236 feet , which was the finished depth of the shaft . The nature of the work in the air shaft was largely experimental , and many difficulties arising from the lack of special equipment and proper technique for precise alinement of the drill holes caused expensive delays before they could be overcome . Drilling the 5-3 /4 - inch hole , which was impeded by frequent core blocks in the core barrel , required 10 shifts . average advance per shift for an EX hole was about 150 feet . The The holes were charged and fired from the surface . The length of the section blasted in one cycle was 10 feet . Blasting progressed from the bottom of the shaft upward . The broken stone dropped into a chute , from which it was drawn into cars on the haulage level . The Bellefonte mine is an underground limestone mine.3/ The primary objective in undertaking the research on shaft sinking by diamond drilling was to perfect a method for driving connections between levels of the mine .

Oct 1, 1948

By Jeremy P. Doolan, Leigh B. Neindorf, Geoff W. Capes

The development and use of rock mass classification tools have been a key component for improving stope design over the past 4 years at the Xstrata Zinc George Fisher Mine in northern Queensland, Australia. In 2003, stope extraction data from 3 years of open-stope mining provided an excellent situation to review the assumptions in the feasibility study. Extracted stope profile information, drillhole geotechnical data, underground observations, and oral and written communication were used to develop a thorough stope reconciliation performance database. With-out collecting the back analysis data and presenting the data in a usable format, engineers are left to debate opinion instead of engineered judgment. This can lead to biased and uninformed design parameter choices with the potential to repeat poor design. This paper demonstrates some effective, practical examples of empirical data collection where rock mass classifications tools were developed and used to create improved confidence in predicting stope stability and failure profiles. The work contributed to design changes that resulted in a reduction in stope hangingwall dilution and an increase in head grade while continuing to ramp up production from 2003–2005.

Jan 5, 2007

By A. L. Engel

[Thi;. re:9ort presents re3ults of investigations of problema a3signed as ore-testing projects to the Ore-Dressing Section, t.fetal1urgica.l Div:biion, of the Bureau of Ii.fines at the .fississippi?Valley E>"'1lcrimcnt Station in rtolla, Ho., durine the fiscal year ended June 30, 1940.]

Jan 1, 1941

By A. L. Engel

[This report presents results of investigations of problems assigned as ore-testing projects to the Ore-Dressing Section, Metallurgical Division, of the Bureau of Mines at the Mississippi Valley Experiment Station in Rolla, Mo., during the fiscal year ended June 30, 1940.]

Jan 1, 1941

By D. A. O'Keefe, M. M. Wong

To obtain beryllium metal of higher purity , flakes produced from electrorefining scrap metal were used as cell feed for a second cycle of electrore fining at 500 ° C in an electrolyte composed of 51.7 mole - percent LiCl , 36.9 molepercent KC1 , and 11.4 mole - percent BeC¹ · Metallic impurities in the flakes totaled more than 108 ppm , the metallic impurities in the metal obtained from the two - cycle electrorefining were , with the exception of 35 ppm of calcium , below the spectrographic determination limits .

Jan 1, 1964

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

By Russell R. Trengove

The Bureau of Mines developed by core drilling the Cove Meadow copper property, also known as the Patterson property, from May 6, 1949, to August 6, 1949. It is in the Cove Meadow mining district, northwestern Humboldt County, Nev., 102 miles northwest of Winnemucca. The purpose of the work was to determine possible reserves in a mineralized shear zone in andesite that has been partly explored by several surface cuts and two shallow underground workings. Production from this zone to August 1, 1,949, was 98 tons of hand-sorted copper ore assaying 5.1 percent. The development work performed by the Bureau of Mines comprised a study of the geology, mapping the area, sampling the outcrops, and exploring by diamond drilling the shear zone adjacent to the fault. Seven holes were drilled for a total of 1,246 feet. Mineral reserves indicated by the project are confined to a length of 500 feet along the strike.

Jan 1, 1950