Search Documents

By W. L. Schmidt

The effect of a water-repellent film in sandstone cores on the effective permeability-saturation relationship was investigated as part of a cooperative research program between the Bureau of Mines and the American Gas Association. The repellent film was formed by the reaction of methyltrichlorosilane3 with the connate water in the core. Other researchers have reported on the use of silicone chemicals to alter the flow characteristics of porous media (1-3, 5-7, 9, 10).4 The previous studies, however, dealt almost entirely with oil-water or oil-gas systems and not with water-gas systems. The primary purpose of this study was to determine the feasibility of using silane to retard the influx of water into natural-gas storage wells and to determine the necessary requirements for achieving this result. The success or failure of silane treatment as a remedial measure depends on its effect on gas-production rate and attendant water production.

Jan 1, 1961

By W. D. Bryson

This paper is one of a series being prepared by the United States Bureau of Mines on tunnel-driving methods. The practices described are those used at No. 11 mine of the Colony Coal Co., Denver, Colo. No. 11 Mine is situated at Dines, some 14 miles north of Rook Springs, in Sweetwater County, Wyo. It is served by a spur off the Winton branch of the Union Pacific Railroad. The Colony Coal Co.'s mines were opened in 1918, and since that time have been among the largest producers of coal for the railroad and domestic markets in the Rock Springs coal district.

Jan 1, 1932

By R. V. Ramani, A. S. C. Owili-eger

The Methane Generator program is a part of the Internal Environ¬mental Sub-system of the Master Design Simulator (MDS). All the sub¬systems of the MDS are controlled and activated by the main program as required. The data requirements for the Methane Generator are supplied by the Geology and Reserves sub-system through common storage. Figure 6 shows the information flow between the Methane Generator and other systems of the MDS. It should be noted that the Methane Generator can also function independently as was described under model application. AREAS OF MISSING INFORMATION In any numerical analysis, the accuracy of the solution depends entirely upon the data available. In gas flow problems, parameters that constitute basic model input data are rock porosity, medium permeability, reservoir pressure and initial reservoir pressure dis¬tribution. Unfortunately, however, most of these characteristics are not available for a lot of coal seams. The need for actual field data cannot, therefore, be adequately emphasized here.

Jan 1, 1974

By M. Clair Smith

The Sweetwater, Castro, Trinidad, New London, and Hilltop chromite properties are situated within an area 8 miles long and 1 mile wide between San Luis Obispo city and Morro Creek, San Luis Obiso County, Calif. Development work at this group of mines was a part of a long-range project by the Bureau of Mines to develop strategic mineral reserves in the United States in accordance with the Strategic Minerals Act of 1939. The junior author of this report participated in the preliminary examinations made in 1941 of the chromite deposits that later in the same year were the subject of more intensive investigation under the immediate supervision of the senior author. The ore occurs in lenses and kidneys in masses of dunite contained in large poridetite areas. Production has boon in the form of lump ore and concentrates from disseminated ore. Work by the Bureau of Miner included surveying, mapping, trenching, sampling, and assaying. It is summarized separately in the text under the name of each mine investigated. The report gives a brief history of the district, describer the concentrating plant of the Castro Associates, and gives detailed results on sampling and assays at the various proportion.

Jan 1, 1951

By Debra A. Griffith

The U.S. Bureau of Mines currently is researching the relationship between the level of back strength and the probability of low-back injury. This report is a review of the literature and statistics on over-exertion injuries. Overexertion continues to be a significant source of injury in metal and nonmetal mining, accounting for approximately 24 pct of all injuries yearly. These injuries, particularly to the lower back, can be very expensive in human and monetary terms. An examination of the accident data on overexertion injuries is necessary to provide a background for research into prevention and/or amelioration of those in-juries. The job categories outlined in the Accident Data Analysis data base most affected are "Mechanic/Electrician" and "Mill/Plant Worker." The age group most affected is "30-39" years, and the experience group most affected is "0-.99" years. The most prevalent type of overexertion injury is "Strain/Sprain," and the trunk is the body part most often involved in an overexertion injury.

Jan 1, 1994

By J. M. Stuve

Thermodynamic properties were determined by the Bureau of Mines for the intermetallic compound, TiA13. Heat capacities were obtained from 5 to 303 K by adiabatic calorimetry. The derived value of S2 1s is 22.08±0.07 cal/deg¬mole. Enthalpies relative to 298 K were obtained from 298 to 1,413 K by copper-block drop calorimetry. No anomalous thermal behavior was noted in the temperature ranges investigated. Low- and high-temperature data were combined with a known enthalpy of formation at 298 K to give values of enthalpy of formation and Gibbs energy formation, 0 to 1,400 K.

Jan 1, 1974

By D. E. Shanks

As part of its program to lessen dependence on foreign bauxite as the Nation's primary source of cell-grade alumina, the Bureau of Mines is investigating sulfuric acid (H2S04) leaching procedures for the recovery of alumina from domestic aluminous materials. The successful application of a H2S04 leaching process depends on the recovery of the aluminum values in an easily washed and filtered form, containing a minimum of water to be driven off in the subsequent calcination step. This goal was met by the high-temperature hydrolysis of simulated aluminum sulfate [A12(S04)3] leach liquor. Crystalline, insoluble aluminum hydroxy sulfate [A1(OH)S04], which had a water-to-alumina mole ratio of 1:1, was produced. Eighty-six percent of a solution containing 127 g of A12(S04)3 per liter and 76 pct of a solution containing 336 g of A12(S04)3 per liter were hydrolyzed to insoluble aluminum hydroxy sulfate by autoclaving for 1 hr at 320° C and rapidly quenching to room temperature. Higher operating temperatures were precluded by corrosion of the autoclave. The yield of aluminum in the hydrolysis product increased with increasing hydrolysis temperature and decreasing A12(S04)3 concentration.

Jan 1, 1981

By D. R. Babich, E. R. Bauer

Noise-induced hearing loss (NIHL) in mine workers, especially underground coal miners, continues to be a problem in the mining industry. The recently enacted MSHA noise standard, Part 62 – Occupational Noise Exposure (Federal Register, 1999), is aimed at reducing NIHL in the mining industry. The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures to address NIHL in various aspects of coal mining including surface mining, coal preparation plants and underground mining. In underground bituminous coal mining, noise surveys, consisting of full-shift worker noise exposure, time-motion studies and equipment noise profiling, have been completed on longwall and continuous miner sections in six underground coal mines. The studies revealed widely varying shift-to-shift worker exposures, with workers in certain occupations routinely exposed to potentially hazardous levels of noise. A summary of these studies is reported, including worker dose, source/dose relationships and equipment noise profiles.

By R. K. Clifford

Chalcopyrite (CuFeSz) concentrates produced on the Lead Belt of Missouri typically contain 28 pct Cu and from 0.5 to 1.5 pct each of nickel and cobalt. Most of the nickel and cobalt are present as the mineral siegenite, (Ni,Co)3S4, almost none of which is recovered presently. The Bureau of Mines, U.S. Department of the Interior, has been conducting research on the chalcopyrite to produce a marketable fraction enriched in cobalt and nickel. Ferric chloride leaching of various chalcopyrite (copper) concentrates has yielded residues containing from 10.2 to 16.2 pct Ni and 8.3 to 11.4 pct Co with recoveries of approximately 79 pct. In another approach, laboratory froth-flotation tests have been conducted to investigate the effects of regrinding, roasting, baking, and steaming prior to flotation, with a variety of reagents. The best laboratory results were obtained after regrinding the copper concentrate to 94 pct minus 400 mesh and floating the chalcopyrite at natural pH (6.5) with 0.48 pound of sodium diethyldithiophosphate and 0.01 pound of sodium cyanide per ton of concentrate. This procedure yielded a tailings assaying 20.4 pct Cu, 5.2 pct Ni, and 3.45 pct Co. The tailings contained 67.2 pct of the nickel and cobalt and 15.9 pct of the copper originally in the copper concentrate; the remainder of the values reported to the flotation concentrate, which analyzed 29.6 pct Cu. To verify the laboratory flotation results, a 60 kg/hr process demonstration unit (PDU) was constructed in the Cominco American Magmont mill, Bixby, Mo.

Jan 1, 1978

By A. W. Fahrenwald

Coarse sand flotation, both alone and in conjunction with gravity concentration, is a subject of research at the U. S. Bureau of Mines Field Office, Moscow, Idaho. One of the most important results of this work which is being carried out in cooperation with the University of Idaho, has been the development of a concentration process embodying flotation, classification, and tabling, in the order named. The flow sheet of the process is given in Figure 1. The type of feed desired for this process is coarser than is common in present "all flotation" practice, and is about the size of table feed.

Jan 1, 1929

By Harry W. Campbell

A mineral survey by Bureau of Mines personnel identified no mineral resources or mineral occurrences with development potential at prospects in the Mecca Hills Wilderness Study Area (WSA). Bentonite occurrences are in Skeleton Canyon and Surprise Canyon. Sand and gravel occurrences are numerous in and near the WSA. Much of the Mecca Hills WSA was leased for oil and gas exploration in 1983. No current mining claims or other leases were found in the study area. The Skeleton Canyon Clay Mine yielded clay to seal irrigation canals, Clay to seal ponds was also mined from the Red Top Clay Mine west of the USA. A sand and gravel pit south of the study area (near Box Canyon Wash) supplied material for local construction projects. A commercial sand and gravel pit was operating in 1983 near the mouth of Thermal Canyon 4 miles west of the WSA.

Jan 1, 1984

By Roy C. Bartholomae

This Bureau of Mines report presents the results of a laboratory investigation of coal cutting mechanics and noise. These experiments were performed using linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts was ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to formulate analytical models of the coal cutting forces and noise. The analytical model for coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as provide benefits to other important areas of health and safety in underground mining.

Jan 1, 1983

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some diamond drilling at the Almedia deposit In an endeavor to find an additional source of supply of lead and zinc. It is reported that in 1816, lead and zinc minerals were found in the limestone quarries near the boundary line between Scott and Center townships. In an attempt to develop these minerals in paying quantities, an alit was driven for several rods into a bluff Just west of the present Almedia mine, This is believed to be the Web mine, mentioned briefly by Parker Cleaveland in 1816. In 1901 the Almedia mine was developed by an open cut and three shafts. The hoisting shaft at the time of drilling by the Bureau of Mines was sounded to a depth of 115 feet. A concentrating plant reportedly made shipments to Hamburg, Germany, for reduction. The deposit is in a somewhat slaty limestone. The ore occurs in a northeast fracture zone along the strike of the limestone and dips to the southeast. Old miners state that the ore appeared as large chunks of galena and sphalerite. In 1949, to investigate the downward extension of the oreshoot, the Bureau of Mines drilled four holes aggregating 1,126.3 feet.

Jan 1, 1950

By B. K. Cantrell, K. L. Rubow

"The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8-um aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 um diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2. NO, NO2, SO2, diesel exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive. During the past several years, though, progress has been made in defining the problem.Results from epidemiological studies by Garshick et al. (1988 ), animal inhalation studies by Mauderly eta). (1986), Iwai et al. (1986), and Brightwell et al. (1986) and in vitro studies by Lewtas et al. (1986) have provided sufficient data for the National Institute of Occupational Safety and Health (NOSH) to recommend that ""whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration"" (NIOSH, 1988). NIOSH further stated that ""though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk.""The Mine Safety and Health Administration (MSHA) has also been directed by an advisory committee to establish a diesel exhaust aerosol standard and to establish regulations to minimize exposure to diesel pollutants in underground coal mines (MSHA,1988). Both reports point out the need for development of measurement techniques for respirable diesel aerosol.In the past four years, the US Bureau of Mines (Cantrell,1987 and Cantrell, et al. 1987), in cooperation with Marple, et al. (1986), at the University of Minnesota's Particle TechnologyLaboratory (PTL), have studied the use of size-selective sampling techniques to measure the mass concentration of diesel aerosol in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler for use in underground coal mines.These criteria are based on the premise that size-selectivesampling techniques,can be used to separate diesel exhaust aerosol, which is predominantly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. In addition to the performance criteria, this paper discusses the laboratory and field test data used to develop the criteria."

Mar 1, 1992

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama and coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba n fields were studied. Tire main purposes of this study has been to evaluate no nearly as possible relative influences of certain factors on rate of drainage and to determine whether the drainage characteristics of coals from different beds or from different mines on the soma bed differ materially. A further objective was the development of a laboratory drainage test that would predict approximately the rate at which any coal will drain after having been loaded into a railroad car in a saturated condition. The study has been confined to samples of slack coals - that is, coals from which none of the fine sizes have been removed. The samples ranged in upper size limits from 7/16 inch to 3 inches. It did not seem necessary to study nut and egg sizes, that is, sizes from which the fine coal has been removed by screening, as these lose water so rapidly by natural drainage that they present no serious problem in dewatering after treatment in a washer. The significance of drainage characteristics of Alabama coals is apparent in view of the fact that not less than 70 percent of Alabama?s total coal product is subjected to wet washing before being materials.]

Jan 1, 1941

By Richard L. Sayrs

"The Stiner zinc prospect near the north boundary of Union Tennessee, and the Bunch Hollow property 5 miles northeast in Claiborne County, Tennessee, were diamond-drilled by the Bureau of Mines during the period .September 1, 1944, to February 22, 1945. Seventeen holes totaling 5,687 feet were completed, 13 of which, totaling, 5.083 feet, were on the Stiner property and the remainder, totaling 604 feet, at Bunch Hollow.The Stiner prospect is about 1 mile east of the old workings known as ""New Prospect"" or ""Lead Mine Bend."" The Federal Geological Survey made a study' of the area early in 1944. The prospect was first visited in August 1944 by Bureau of' Mines engineers3/ accompanied by members of the Federal Geological Survey.4/ The locality is reached by traveling State Road 33 north-about 9 miles from Maynardsville, Tenn., thence northwest about 7 miles by an improved county road that leads to the mine (fig. 1). The tract comprises an area of about 181 acres held by G. S. Stiner of Sharps Chapel, Tenn.; it is now under option to the Universal-Exploration Co. of Jefferson City, Tenn.The Bunch Hollow property, about 5 miles northeast of the Stiller prospect, was also studied by the Federal Geological Survey previous to being;Visited by Bureau of Mines engineers in August 1944. It is reached by traveling north from Maynardsville, Tenn., on State Road 33 about 13 miles, thence northwest by county road 6 miles to the property (fig. 1). The last 3 miles of the county road are in poor repair but are passable during the entire year. The property comprises an area of approximately 300 acres and is held by the imperial Mining Co., Pressman's Home, Tenn.Few reliable data are available as to the history of the Stiner prospects themselves. However, the New Prospect mine, 1 mile west, has had a colorful past, This mine was opened in 1883 and was worked intermittently until 1918, by which time more than 65,000 tons of concentrates had been shipped. No further work was done until 1942, when the mine pillars were robbed and 1,900 tons of ore averaging 25 percent zinc was shipped to the New Jersey Zinc Co., Austinville, Va."

Apr 1, 1946

By B. R. Mohal, S. Chander

"The adsorption and wetting behavior of freshly ground and aged coals has been determined in the presence of a nonionic surfactant. The amount of surfactant adsorption changes with the concentration and ""age"" of the coal. The freshly ground coal has smaller amounts of adsorption at lower surfactant concentrations than the ""aged"" coal whereas at large surfactant concentrations, the order is reversed . In the latter case, more surfactant is adsorbed on fresh coal than on the ""aged"" coal . . It is proposed that at low concentrations, the surfactant adsorbs through both hydrophobic and hydrophilic interactions with the molecule lying parallel to the· surface, whereas at higher concentrations surface micelles form at the hydrophobic sites. The wetting behavior correlates well with the adsorption behavior.INTRODUCTIONNonionic surfactants have many applications in the coal and mineral processing industry. They can be used as dispersing agents to modulate flotation, flocculation and filtration of particulates (1). They can also be used to increase the wettability of hydrophobic solids such as coal and can hence be used as dust suppressants (2,3). Although the adsorption of representative nonionic surfactants such as Triton N-101 (an ethoxylated nonylphenol with 9.5 moles of ~thylene oxide and HLB equal to 13.4) have been studied extensively on substrates such as calcium carbonate (4), silica (5) carbon black (6) and graphite (7), very few studies are available for coals. Coals differ from other substrates with respect to two important characteristics: 1) coal are porous and 2) coals consist of a patchwork of hydrophobic and hydrophilic sites (8). Since the adsorption characteristics of a surfactant are influenced significantly by the nature of the substrate the characteristics of the coals must be taken into consideration."

Jan 1, 1989

By A. B. Coates, J. E. Crawshaw

"The use of such methods and apparatus as the Dautriche method and the Mettegang recorder for the determination of the rate of burning of black blasting powder and other strictly burning explosives has been found to give such erratic results that no reliance can be placed on the data thus obtained. Consequently, investigators of those factors which may affect the burning rate, such as size of grain, absolute density, chemical composition, and means of ignition have had to rely mainly on observations made during practical use for determination of the part played by each. Such tests are very difficult of interpretation.The purpose of this paper is to describe a method used by the explosives division of the Bureau of Mines for the investigation of such explosives and to present the results of an investigation using that method.The investigation was concerned with the effect of grain size, initial pressure, and means of ignition on the rate of burning or rate of pressure development of black blasting powder as compared with pellet powder.The Bichel pressure gauge was used for these tests, with the slight modification to the apparatus and method described in U. S. Bureau of Mines Bulletin 15.4 These modifications consisted of reducing the speed of the revolving drum on which the time-pressure record is taken, measuring the speed of the drum by a belt-driven tachometer, and introducing an induction coil in series with the electric squib or electric detonator to mark on the time pressure record the instant at which the squib or detonator was fired."

May 1, 1929

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba fields were studied]

Jan 1, 1941

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974