Search Documents

By John M. Gomes

A two-phase molten halide-silicate technique for extracting tungstic oxide (WO3) from scheelite (CaW04) and wolframite [(Fe, Mn)W04] was investigated. The halide phase extracted over 99 percent of the was, whereas the lower silicate phase retained about 90 percent of the calcium, iron, or manganese oxides. The most efficient extraction and separation of tungsten from scheelite was accomplished at 1,080° C in a molten system containing, in mole-percent, 9 calcium tungstate (CaW04), 42 sodium chloride (NaCl), 28 sodium fluoride (NaF), 17 sodium metasilicate (Na2SiO3), and 4 alumina (Al2O3). Wolframite was also treated at 1,0800°C; the molten system contained, in mole-percent, 11 (Fe, Mn)W04, 74 NaCl, and 15 Na2 SiO3.

Jan 1, 1968

By A. F. Colombo

Laboratory-scale tests were conducted by the Bureau of Mines on an argillaceous Michigan copper ore and mill tailing to determine the feasibility of leaching with acidified ferric sulfate solutions. The ore and tailings, containing 1.24 and 0.24 percent copper, respectively, were from the White Pine Copper Co., Ontonagon County, Mich. The investigation showed that ferric sulfate leaching of the ore and tailings followed a predictable pattern. Thus, with 4 hours of leaching, up to 58 percent of the copper in the ore was extracted, but prolonged leaching (2 to 3 weeks) was required to dissolve more than 90 percent of the copper. Similarly, about 50 percent of the copper in the mill tailings sample was dissolved in a few hours, but 8 days or more were required for extractions of over 90 percent.

Jan 1, 1962

By J. H. Rose

This paper describing the milling practice at the Magma Copper Co., Superior, Ariz., is one of a series being prepared by the Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to William Koerner, general manager of the Magma Copper Co., for permission to prepare this article; to J. S. Garrott, former mill superintendent, for the historical facts; and to Walter Cooksley, general foreman, for his assistance in obtaining the data.

Jan 1, 1930

By C. M. Frost

The hydrodesulfurization characteristics of a residual fuel prepared from Wilmington, Calif., crude oil were determined at temperatures from 600° to 900° F, pressures of 200 to 800 pSig, and space velocities from 0.2 to 2.0 Vo/Vc/hr, using cobalt molybdate type catalysts. A prediction equation, developed from the experimental data, satisfactorily predicts the fraction of total sulfur that can be removed under any combination of operating conditions within the ranges investigated. Yields and properties of the low sulfur product are correlated with the fraction of total sulfur removed. Kinetic calculations show that the apparent reaction order and activation energy change with space velocity and temperature.

Jan 1, 1970

By A. L. Engel

The sample of ore on which the work described in this paper was done came from Mina Oriente, Carrizal Bajo, Provincia de Atacama, Chile, South America, and was sent at the request of the Chil.ean Government through the Foreign Minerals Division of the Bureau of Mines. This ore had been tested locally for treatment by flotation and cyanidation without satisfactory results. An additional difficulty was the absence of water near the ore deposits, so that in any treatment method considered the water requirements would have to be very low. It was desired to develop a practical method of recovering the gold and, if possible, the copper in the area. No data of previous investigations were made available. The sample received was mostly quartz, highly brecciated, with limonite and hematite in the fractures. Copper occurred as malachite and azurite, also in the fracture s and to a slight extent as a stain in the quartz. Some fine-grained pyrite with a little arsenopyrite occurred within the quartz. An occasional grain of chalcopyrite was observed. No free gold was seen during examinations of the ore, but amalgamation indicated that some was present.

Jan 1, 1949

By Clark F. Grain

The monoclinic to tetragonal inversion of zirconium dioxide was studied by single-crystal X-ray methods, high-temperature X-ray diffractometry, and differential thermal analysis. The unusual features of the inversion, such as no definite transition Lperature, hysteresis, and athermal kinetics, were confirmed for powders who mean crystallite size was greater than 1,000 A. Samples of mean crystallite size below 1,000 A displayed classical kinetics, obeying a logarithmic rate law. A detailed mechanism based on Ubbelohde's theory of continuous phase transformations was proposed which is consistent with all the experimental facts.

Jan 1, 1965

By Seth C. Schaefer

As part of the Bureau of Mines, U.S. Department of the Interior, effort to provide thermodynamic data for the advancement of minerals technology, the Gibbs energy of formation of sphalerite (zinc sulfide) was investigated with a high-temperature galvanic cell employing stabilized zirconia as the electrolyte. In the temperature range 948 to 1,210 K, potential measurements were obtained for the cell Pt, ZnS + ZnO, S02 = 1 atm // Zr02 // Cu20 + Cu, Pt, with the overall cell reaction ZnS(c) + 3 Cu20(c) = ZnO(c) + 6 Cu(c) + S02(g). (1) These results, combined with the best available values of ?Gf° for ZnO, S02, and Cu20 from the literature, give the Gibbs energy of formation of zinc sulfide for the reaction Zn(l,v) + 1/2 S2(g) = ZnS© (2) ?Gf° = -64.223 + 24.02 X 10-3T ± 0.650 kcal/mole (3) (948-1,180 K; standard states - pure liquid zinc and S2 gas at 1 atm), and ?Gf° = -92.720 + 48.17 X 10-3 ± 0.650 kcal/mole (1,180-1,210 K; standard states - pure zinc vapor and S2 gas at 1 atm). A third law analysis yields for the formation reaction Zn(1) + 1/2 S2(g) = ZnS(c), (5) a standard enthalpy of formation as follows: ?Hf298.15 = -63.64 ± 0.700 kcal/mole.

Jan 1, 1978

By L. L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P205, is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pct P205 and a P205 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1981

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

RECOMMENDATIONS FOR FURTHER WORK Based on the development effort and full-scale tests conducted during this program, a number of technical areas for future research and development have been identified. Further work in these areas would help to improve the reliability, speed of operation and efficiency of the remote sealing system. Recommendations for future work are summarized as follows 1. Development of an Inert Gas Generator For the sake of expediency in conducting the field test program, fresh air was used as the fluidizing medium for the fly ash. However, in an actual mine fire application the use of fresh air is likely to be prohibited. An inert gas, such as nitrogen, carbon dioxide or air containing less than 8 percent oxygen would be required. Using combustion as a means of reducing the oxygen content of air appears to be an attractive solution to the generation of the high flow rates of gas required (2500 to 5000 scfm). Such an inert gas generator would serve a dual purpose for the overall fire extinguishing operation. First, it would provide the inert gas for fluidizing the fly ash. Second, it could be used for inerting the fire area after the seals had been placed, thereby reducing the time required to extinguish the fire. It is recommended that the Bureau undertake a program to develop a field-operable, inert gas generator to satisfy these two requirements. 2. Development of a Field-Operable Sonar Initial Probing System A first stage prototype of a sonar initial probing system was developed during this present program. The results obtained with

Jan 1, 1973

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0.5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that quenched slags can be treated at slightly lower cost than slow-cooled slags. However, the cost advantage of processing quenched slags is more than offset by the higher copper recoveries obtained from slow-cooled slags.

Jan 1, 1971

Use controlled blasting techniques to reduce blast-produced overbreak damage to underground mine ribs and back for both safer working conditions and improvements in productivity. The Problem Blasting is used in metal and non-metal underground mine slopes, drifts and crosscuts to fracture rock to be excavated and further processed. Standard blasting also produces fractures in the rock beyond the desired excavation area. This is sometimes evident by rough surfaces, undercutting and other signs of excessive damage. This damage contributes to rockfalls in the mines, a major cause of injuries and fatalities, and equipment damage. A variety of controlled blasting techniques has been developed for civil engineering projects where long-term stability is essential. For several reasons, these methods arc not widely used in mining. For example, these methods incur additional costs and time; there is little need to maintain stable openings over long periods of lime; and there is the perception (hat corrective remedial techniques, such as rock bolting, are more practical. Basically the benefits of these methods are not demonstrably clear for application in underground mines.

Jan 1, 1991

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

By A. D. Hahn

This report describes and gives the results of an examination by the Federal Bureau of Mines of ilmenite-bearing placer sand deposits in the 24-mile long valley of Otter Creek, Kiowa and Tillman Counties, Okla. Drilling and sampling was completed in three periods between October 1956 and September 1957. Mineralogic studies and mineral-dressing tests on recovery of ilmenite and other heavy minerals from composited samples of the sands were made in Bureau of Mines laboratories at Rolla, Mo., in 1957 and early 1958. Otter Creek rises in and drains the southwestern extremity of the Wichita Mountains, which are represented locally by knolls and ridges of gabbro and granite surrounded by plains floored with flat-lying Permian red beds. The valley fill consists of a basal sand-clay component, derived from weathering of the igneous rocks, and an overlying silt-clay alluvium. Ilmenite is present in significant quantity and recoverable grain size only in the basal sand-clay.

Jan 1, 1960

By Kray Luxbacher, Erik Westman, Peter Swanson

Three-dimensional time-lapse velocity tomograms were generated to image stress redistribution around a longwall panel to produce a better understanding of the mechanisms that lead to ground failure. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Most similar studies have utilized active sources including longwall shearers, controlled explosions, and hammer blows. These active sources generally require a person to initiate and measure the location and time of the source, and are not conducive to continuous monitoring. This method utilizes mining induced microseismic events as passive sources and lends itself well to continuous monitoring. Two event location methods were compared in order to move toward quantification of tomographic results in terms of ground conditions. Additionally, LAMODEL was utilized to determine the expected stress distribution around the longwall panel and compare these images to the velocity tomograms. Eighteen tomograms were generated, one per day, and high velocity regions in the set of tomograms generated from the initial location algorithm correlated with abutment stress redistribution predicted by numerical modeling. This research is significant as it has the potential to improve safety in underground mines and is the only example of long term passive velocity tomography implementation for the purpose of inferring stress redistribution around an area of active mining. Though still immature, this technology has the potential to allow mine personnel to image areas of active mining on a regular basis and detect areas with anomalous velocity distributions indicating potential safety hazards.

By A. B. Hooker, Ilsley. L. C.

"Several writers have called attention, in the technical press, to the possible failure of flame safety lamps in coal-dust laden atmospheres. Such writers question the safety or a flame lamp that has been proved only in atmospheres containing methane, believing that the resistance of the lamp to explosion would be lessened it coal dust constituted a part of the explosive mixture.If this be true, it follows that any series of tests devised to prove the safety of flame lamps for use in gaseous and dusty coal mines should not only embrace tests in mixtures containing various proportions of methane, but also in some of the tests the effect of adding coal dust to the explosive gaseous mixtures should be investigated.Some attention has been given this question by investigators, but the more common practice has been to make all tests in gas and air mixtures only, using methane when it was readily available. Apparently the English Accident Committee (1879-1886) who conducted tests upon 250 different lamps did not use coal dust in their tests. The first British requirements for the testing of safety lamps, issued as a result of the Coal Mine Act of 1911, made no mention of tests with coal duet.The Austrian Fire-damp Committee (1890) conducted a series of tests in which coal dust was used in some of the tests. In certain tests, the addition of coal dust apparently lowered the resistance of the lamp 1 meter per second. The Belgium investigators, Messrs. Watteyne and Stassart, conducted a series of tests in 1904 in which coal dust was used in a few tests without any marked difference in safety."

Dec 1, 1920

By A. L. Engel

Production of chromite in California has been from many small, high-grade mines. The opening of the Purchase Depot at Grants Pass, Oreg., in 1951 has stimulated chromite mining in California, and a large number of properties are being reexamined as there is a possibility that some low-grade ores from many of these properties can be beneficiated to meet the purchasing schedule. The Bureau of Mines in its program of conservation is continuing ore-dressing tests on chromite ores to better evaluate their potential. This report is a compilation of preliminary concentration tests on samples from five different properties in California. The concentration tests were made on ores from the David mine, Butte County, the Seiad Creek mine, Siskiyou County, the High Plateau mine, Del Norte County, Bud's mine, Tuolumne County, and tailings from the Miller concentration plant in San Luis Obispo County, Calif., to determine the possibility of beneficiating these ores so that they will meet the specifications for the Government stockpile.

Jan 1, 1956

By David A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. 80122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available. Personnel involved in the investigation include J.R. Wait (Principal Investigator), D.A. Hill (Co-Principal Investigator), K.P. Spies, A.Q. Howard, and Lana Slusher (Administrative Assistant).

Jan 1, 1974

By W. A. Calhoun

A method for treating high-iron Arkansas bauxites for recovering both abrasive and metal-grade bauxite has been developed by the Bureau of Mines. Present practice usually produces a reject containing appreciable quantities of metal-grade bauxite; however, the processing renders the alumina in the reject unsuitable for the Bayer extraction treatment. Thus the Arkansas abrasive bauxite industry has, in the past, produced little or no metal-grade bauxite. The present investigation was made to determine the possibilities of batter utilization of those particular bauxites through recovery of the wasted metal-grade portion. The large expansion of aluminum-production facilities planned for 1951-53 makes recovery of metal-grade bauxite from presently treated abrasive and marginal abrasive ores en especially timely objective and a welcome addition to our aluminum potential. The quality of the Arkansas bauxites and the inherently associated titania content have made this material particularly attractive to the abrasives industry. however, the gradual depletion of natural abrasive-grade bauxite reserves in this area, the comparative scarcity of high-grade ore, and the difficulty of maintaining adequate reserves have necessitated blending different grades of bauxite calculated to meet specifications. Production of abrasive-grade bauxite from tile, high-iron reserves 13 becoming, increasingly necessary. In one commercial operation, producing abrasive-grade from ores averaging slightly less than 10 percent Fe2O3, approximately 2.7 tons of ore are required to produce 1 ton of abrasive-grade bauxite. The reserves of ore of this grade, however, have been considered inadequate for a long-range production, and ultimately ores averaging 12 to 15 percent Fe2O3 will have to be treated to moot the continued demands of the abrasive industry.

Jan 1, 1952

By Charles L. Kimbell

In overview, 1988 appeared to be the best year for the world's mineral industry since 1980, although the all-important petroleum component suffered severely from low prices. With this notable exception, the traditional statistical measures of mineral industry performance, namely production, trade, and consumption, reflected growth in most elements of the world mineral industry from crude material extraction through the gamut of downstream processing. Moreover, the growth was reasonably well distributed geographically, with many countries sharing in the substantial upturn in activity. World crude mineral output value was estimated at over $1,272 billion in current dollars ($1,090 billion in constant 1983 dollars). The value added by the processing component of the mineral industry raised the total value of the industry's output to an estimated $3,057 billion in current dollars ($2,620 billion in constant 1983 dollars). Less easily assessed was the value of mineral commodities moving in 1988's international world trade, particularly because of the declines in world crude oil and refinery product prices. It remained to be seen if increased volume and value in nonfuel mineral and coal exports, coupled with an increase in the volume of oil exports, would be adequate to offset the drop in oil prices. Whether or not the value of world mineral commodity trade topped the 1987 level of over $498 billion, an increase in the volume of mineral commodity trade was almost assured. Similarly, although comprehensive statistics were not avail-able on consumption of all mineral commodities in all countries, available data on selected major commodities in selected major countries suggested that not only had output of most mineral commodities advanced, but so too had consumption levels for most commodities.

Jan 1, 1990

By J. Sottile, J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine. Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert- system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 1993