Search Documents

By J. P. Powell

Since the beginning of waterflooding in the Midcontinent area, the Bureau of Mines has published many reports3-6/ describing in detail the results obtained on individual waterflooding projects in the area. These are intended as guides for operators in the selection of well-spacing, water-treating, and other techniques, as well as an indication of the results being obtained in waterflooding in various areas, fields, and horizons. In addition, Bureau personnel has arranged a tour of selected waterflooding projects each year for the past several years so that actual operating conditions may be observed and an additional opportunity provided for exchanging information. Each of these tours has been supplemented by a published

Jan 1, 1959

By Albert L. Toenges, Louis A. Turnbull, Henry E. Dekay, James N. Scudder

A preliminary survey of coke and steel plants conducted by the Bureau of Mines in cooperation with the Office of Solid Fuels Coordinator and under the auspices of the Coke Production Committee indicated that a very appreciable increase in pig-iron production would be obtained if pres- ent blast furnaces were supplied with a more uniform coke. Control of the sulfur and ash content of coal used for making coke is an important factor in producing uniform coke and thus increasing blast- furnace efficiency. In some mines producing metallurgical coal, the analysis of the coal bed shows a wide range of sulfur and ash content. To obtain production of coal with minimum deviation in sulfur content sampling, grading, selective mining, blending, and surface preparation are practiced at some mines with satisfactory results. The mines selected for this study have developed these methods and are successfully producing coal of uniform sulfur and ash content. The systems employed at different mines vary according to the physical character- istics of the coal bed, the manner of occurrence of impuritites in the coal, the development plan and mining system, surface preparation and the acceptable impurity content of the prepared coal. The ash content of the coal can be controlled by face preparation and in the cleaning plant. The introduction of some method or practice at other mines might make possible the use of coal for inetallurgical purposes that otherwise could not be used for making coke because of the wide variation of sulfur and ash content.

Dec 1, 1943

By John I. Kasteler

The Rambler mine is in the Douglas mining district, Albany County, Wyo. (fig. 1). The property was first operated about 1870 for gold found in the outcrop of a leached ore body. Copper and metals of the platinum group were discovered, in 1900, or soon thereafter, and intermittent mining was done until 1918, when a fire destroyed the surface plant, and the underground workings caved. The mine has since been idle. The Bureau of Mines conducted a development project on the property from October 1942 to October 1943, with a recess period between November 1942 and August 1943. Ten diamond drill holes, totaling 1,859 linear feet, were drilled on the property (fig. 2). The mine dump was sampled after preparation with a bulldozer. Assay determination and spectrographic analyses disclosed small quantities of copper and metals of the platinum group in the samples. Determinations were made on 11 samples from the diamond drill holes and 23 samples from the mine dump. The assay results and spectrographic analyses are given in tables 1 and 2. The logs of the diamond drill holes are given in an appendix to this report.

Jan 1, 1949

By O. M. Bishop

The Douglas fluorite property is in the Empire district of eastern Pope County, Ill., which lies near the west boundary of the productive Southern Illinois fluorspar field in Hardin and Pope Countios. Production from mines on the Douglas property accounts for about one-half of the 72,000 tons of fluorspar with which the Empire district is credited. This output was from the Sycamore, Pierce, Slapout, and Empire veins, which are normal fissure veins of little displacement along which there has been local wall-rock replacement by fluorite.

Jan 1, 1949

By S. J. Duda

Procedures for detecting and locating seismic sources are adapted to the case of entrapped miners. During an emergency the entrapped miner is likely to generate seismic signals, by knocking against the walls of the shaft. With a seismic array station deployed near the disaster area, the seismic signals can be recorded. Two algorithms are presented for the location of the source from the arrival times of a seismic phase: The first algorithm produces one, most probable location, under the assumption of constant velocity of propagation of seismic waves in the medium. The second algorithm is similarly applicable, however without any restriction on the seismic velocities in the medium between the source and the array. While the first algorithm uses an analytic approach, the second one is based on a trial and error procedure. The second algorithm gives locations with arbitrarily high accuracies, depending only on the accuracy of arrival time measurements and on the compatibility of the true velocity distribution and the assumed velocity model. The algorithm is shown not to require under certain conditions direct .arrival time measurements, thus eliminating a potential source of errors in the location of entrapped miner.

Jan 1, 1973

By D. R. Flinn

A newly developed chemical conditioning technique, which greatly simplifies the preparation of plating baths for the electrodeposition of titanium diboride (TiB2) coatings, is described in this report. The new plating technique was used to prepare samples of titanium diboride (TiB2) coatings on three types of substrate materials. These samples were then evaluated in both low- and high-speed wear-test programs to determine the wear resistance, microhardness, and adhesion of the coatings. In general, it was found that the wear resistance of the coatings is independent of substrate. Scanning electron micrographs have shown that the coating wear surfaces are very smooth, suggesting slow and continuous removal of the coating during the wear test (that is, adhesive wear). Adhesion between the coating and all substrates was excellent. Microhardness results show that the TiB2 coating is harder than alumina, with a hardness value exceeding 5,000 kg/mm2 measured in one test. The results of the wear tests show that TiB2 coatings have relatively poor wear resistance compared with alumina in low-speed unlubricated sliding environments, but exhibit wear properties comparable with alumina in high-speed unlubricated sliding environments.

Jan 1, 1981

By David C. Oyler, Gregory Hasenfus, Gregory M. Molinda

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation stopping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented.

Several short color films describing new technology developed through Bureau of Mines research are available on a loan basis. The films review results of Bureau research programs aimed at aiding the minerals industry by increasing mine productivity, ensuring worker health and safety, and enhancing minerals recovery, processing and recycling. Most of the films are available in a choice of for mats: 16mm film, ½" VHS cassette tape, or ¾" U-matic tape. The films are loaned by the Bureau of Mines free of charge; borrowers are requested to pay only the return postage and for any damage to the films. All titles are also available for purchase in 16mm or videotape formats. Interested persons wishing to borrow or purchase a film should specify its title and the preferred and alternate showing dates. All requests should be addressed to: Motion Picture Library Bureau of Mines Cochrans Mill Road P.O. Box 18070 Pittsburgh, PA 15236 A short description of each film follows: Safer Coal Mining Equipment Traces the development of modified conventional and continuous mining equipment, beginning with an investigation of the problems encountered with mining equipment and continuing through long-term testing of the modified equipment in two mines. "Human engineered" coal mining machines are shown in operation. These machines include features such as adjustable cabs, easy access controls, improved illumination, and other safety improvements. (19 min)

Jan 1, 1986

By James P. Rider, Jeanne A. Zimmer, Andrew B. Cecala, Robert J. Timko, Earle H. Andrews

Many different types of structures and materials have been used to build mineral processing facilities over the past few decades. Although the structure type and building material were not viewed as significant factors affecting the health of employees in these facilities when they were built, the National Institute for Occupational Safety and Health performed an evaluation to determine to what extent building types could impact respirable dust and noise levels. This report discusses the evaluation of three different types of product sizing silica sand structures: a masonry design, a steel-sided design, and an open structure design. The data obtained in this study indicate that the open structure design (no walls) was superior from both a dust and noise (health) standpoint compared to the other two structures. The open structure design should also be beneficial from a cost standpoint because of lower material and construction costs. Companies and design engineers should consider this open design when building new mineral processing facilities in climates where it could be applicable. Some companies may also want to consider modifying existing structures with a more open design to further reduce dust and noise levels. As the trend continues in lowering allowable dust levels for federal health standards in the U.S. mining industry, the open structure design may be an approach for some companies to consider for their operations.

Jan 11, 2006

By L. F. Heising

This report is a general summary of pertinent data on the manufacture and use of synthetic ammonia products. It provides a condensed summary of the potentialities of a synthetic ammonia industry in North Dakota for Federal, State, and private organizations that may be interested in helping to develop an integrates synthetic ammonia and fertilizer industry. The report contains discussions of: (1) Materials used in the manufacture of nitrogenous fertilizers, nitric acid, and urea; (2) National production, imports, exports, and consumption; (3) the ammonia industry, location, capacity of plants; (4) processes used in manufacturing synthetic ammonia, nitric acid, and urea; (5) other potential industries; and (6) analyses of manufaturing and plant cosh;. Additional information on industrial compounds from ammonia and plant nutrients removed by crops is given in Appendixes 1 and 2. Synthetic ammonia is one of the primary ingredients in fertilizers. Resources required in synthetic ammonia manufacture are available in North Dakota. Hydrogen is available from the petroleum and natural gas resources, particularly in the Williston Basin, and from the large lignite resources in the State. Hydrogen can be produced from lignite by a gasification process developed by the Bureau of Mines at Grand Forks, N. Dak.

Jan 1, 1954

By M. J. Ferrante

Laboratory-scale tests were undertaken to examine several electrolytes for possible use in separating nickel and cobalt from products being prepared at Nicaro, Cuba. The most extensive work was done with nickel sulfate-ammonium fluoride, ammonium fluoride, ammonium sulfate, and nickel sulfate-boric acid electrolytes. All four electrolytes exhibited some selectivity for dissolving nickel carbonate from Nicaro basic carbonate used for regeneration. The nickel sulfate-ammonium fluoride electrolyte exhibited less selectivity for dissolving nickel carbonate from Nicaro basic carbonate than it did from synthetic mixtures. Ammonium fluoride leaching experiments showed that a low concentration and high temperature gave a good nickel extraction with C. P. reagents; however, this was not confirmed in tests using Nicaro basic carbonate. Electrolytic tests employing ammonium fluoride leach liquors gave no further separation, since approximately 90 percent of the cobalt was deposited at the cathode with the nickel.

Jan 1, 1958

By Anthony J. Miscoe, William M. McKewan, Richard C. Wang

The behavior of wire ropes used in hoisting is not well understood. In an effort to improve this understanding, the structure of round-strand wire ropes was analyzed. This report provides a generalized mathematical model that completely describes the geometry of the wires. It consists of two sets of vector equations and is valid for any round-strand wire rope. One set of equations is used to trace the paths of wires that have the form of a single helix; the other is used for the paths of double helical wires. The specific model for a 33-mm 6×19 Seale, independent wire rope core (IWRC), right regular lay wire rope was presented as an example. The paths and the geometric properties of the wires, which include the path length per lay of strand, the curvature, and the torsion, were determined from this model. The effects of strain deformation were analyzed, resulting in a system of equations for determining the structural parameters of the deformed rope. In future work, the model could be used to analyze wire ropes of different constructions so that a more scientifically based understanding of rope behavior can be established.

Jan 9, 1998

1.1 DEVELOPMENT OF INDUCTANCE MATRICES The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available either from handbooks or from the manufacturer's published data. Thus, it is useful to summarize the derivation of the origin of the inductance matrix from basic principles. 1.1.1 Flux Around a Cylindrical Conductor The flux pattern around a cylindrical current carrying conductor can be found by using symmetry in conjunction with Ampere's Law. From symmetry it is clear that the flux lines which always close on themselves must be concentric circles. Thus, from symmetry alone one can get a qualitative picture of the magnetic field. This is shown in Fig. 1.1 where the inner circle represents the solid round conductor and the outer circle represents a flux line. The quantitative picture will now be developed using Ampere's Law.

Jan 1, 1973

By Christopher C. Jobes, Alan G. Mayton

The National Institute for Occupational Safety and Health (NIOSH) researchers have investigated seat design issues for the occupants and operators of underground mine transport vehicles relative to whole-body vibration (WBV) and mechanical shock. Considering the ergonomic and engineering improvements made to underground mine shuttle car seats, this study has focused on reducing injury risk by improving seating on transport vehicles such as scoops, mantrips, personnel carriers, and rail-mounted locomotives. Similarly, proposed seat design improvements included layering of various types of viscoelastic foam padding to isolate vehicle occupants and operators from adverse health effects of jarring/jolting exposure. This paper discusses the results obtained from laboratory vibration testing of new seat padding materials in seven configurations at the NIOSH – Pittsburgh Research Laboratory (PRL) showing that careful use of configuration and materials can reduce the operator’s exposure to WBV. In addition, results for four mine transport vehicles are presented from field data collection efforts at a Southwestern Pennsylvania mine showing that a NIOSH based design does reduce the operator’s exposure to WBV. Finally, the authors discuss efforts to develop and field test seat padding interventions using new padding materials and configurations based on the laboratory test results [The findings and conclusions in this report are those of the author(s) and do not represent the views of the National Institute for Occupational Safety and Health.]

By Sam G. Demou

Drag bit cutting tests were conducted chiefly to determine bit forces encountered in rock types representing a range of compressive strength and hardness and thus enable the design engineer to estimate a continuous miner's performance in a range of rock types. Testing was carried out on the Bureau of Mines uniquely designed, instrumented rock cutting device (RCD). This device can make 3-ft-long cuts at various depths and speeds to approximate full-scale drag bit cutting by continuous miners. Point attack and cutter bits were tested on four rock types ranging in compressive strength from 7,200 psi (trona) to 29,600 psi (Valders white rock). Cutting tests were made at depths up to 1 in and speeds up to 70 in/sec. Data included normal and cutting forces, groove depth, groove width, and weight of rock broken. The effect of varying the cutting speed was determined, and specific energies were calculated for the various conditions. The bit wear was also observed. For the rocks tested, compressive strength and hardness are good indicators of forces, specific energy, and wear encountered. Results, especially bit wear observations, show the possibility of extending continuous miners, already being used in trona, to Indiana limestone (10,000 psi). Rapid bit deterioration precludes use in Tennessee marble (16,800 psi) and Valders white rock (29,600 psi).

Jan 1, 1983

Develop improved blasting practices that can help to curb overbreak in highwalls at surface mines, thereby reducing the hazards of rock-falls to workers and equipment, The Problem The serious hazard in surface mining is the falling of rock from highwalls. Poor highwall stability is caused in part by geologic conditions, but often is aggravated by faulty blasting practices, where the explosive energy not only fractures the rock to be excavated, but also damages the rock that borders the excavation. This reduces the general stability of the hlghwall and increases the rockfall potential. The probability of injury to mine workers or damage to equipment associated with exposure to the highwall increases with the height of the highwall and the extent of its overbreakage. Most rockfalls occur in the first 15 days after a new highwall is exposed. This statistic is significant since most of the work below a highwall is done during this period. The area of greatest hazard is within 25 ft of the toe for rocks that fall vertically, and up to 90 ft from the toe for falling rocks that are deflected by the highwall during their descent, The workers most frequently involved in such accidents are dozer operators, ground laborers, and shovel operators or oilers.

Jan 1, 1985

By Charles E. Whieldon

Data on the oilfields in Mahoning, Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and compiled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965

By T. F. Anstett

The Bureau of Mines estimated the potential availability of tungsten from 57 mines and deposits in 19 market economy countries. The tungsten resources of China and the U.S.S.R. were also estimated. This resulted from an evaluation of tonnage-cost relationships indicating the quantity of tungsten available as ammonium paratungstate (APT), artificial and natural scheelite, and ferrotungsten at various average total costs of production including 0- and 15-pct rates of return on invested capital. The evaluated deposits contain 1.2 million metric tons (t) of recoverable WO3, of which approximately 52,000 t of AEYT can be produced at the January 1983 market price of $5.37/lb, 89,000 t of natural and artificial scheelite at a market price of $3.63/lb, and 1,700 t of ferrotungsten at $5.61/lb of tungsten. An annual availability analysis indicates that by the early 1990's new deposit discoveries, development of known prospects, or expansions of producing mines will be necessary to meet projected tungsten demand.

Jan 1, 1985

By Thomas M. Barczak

Secondary roof support systems play a vital role in preserving the safety of underground mine workers by preventing the unintentional collapse of the mine roof. Hundreds of thousands of standing roof supports are constructed each year in underground coal mines. Historically, wood and concrete cribs and timber posts have been used for secondary roof support. These support constructions require the handling of heavy and bulky materials, causing numerous injuries to the mine workers and resulting in more than 40,000 lost workdays in the past 9 years. Since 1993, various alternative support technologies have been developed. These new support technologies not only provide superior roof support, but many also have significant material handling advantages by using smaller and lighter weight materials, fewer components, mechanically installed support systems, and pumpable support systems. The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive material handling research and has developed recommended lifting thresholds to reduce material handling injuries. An analysis of roof support construction reveals that conventional support materials used in wood and concrete cribbing exceed the recommended lifting thresholds, while the engineered support systems are closer to the recommended weight thresholds. Finally, recommendations are made relative to proper lifting techniques and material handling practices to prevent injury to mine workers when constructing roof supports in underground coal mines.

Jan 10, 2000

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rim. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988