Search Documents

By John R. Bartels

This Bureau of Mines report describes the development of a preliminary design for a novel, protected, cab-shuttle car for use in working seam heights down to 40 in. Because of the severe restrictions imposed by low-coal operation, Mine Safety and Health Administration (MSHA) regulations only require canopy protection on shuttle cars operating in seam heights of 42 in or greater. MSHA routinely grants variances for canopy use in seams 48 in high or less. The design was generated by giving the operator needs equal priority as related to machine performance parameters. Cab-shuttle car concepts that led to the recommended design are described, along with criteria and testing used to evaluate their potential effectiveness.

Jan 1, 1988

By David C. Oyler

Methane-drainage holes must be completely filled by grout before mining to prevent the emission of large quantities of gas during mine-through, which would constitute an explosion hazard. In November 1980, seven horizontal holes at the multipurpose borehole, a small-diameter shaft drilled as a Bureau of Mines coalbed methane-drainage installation on the property of the Federal No. 2 Mine, Monongalia County, WV, were plugged using a sodium silicate gel grout. This report de- scribes the grout mix and the use of the grout at the multipurpose borehole, and discusses the results observed upon mine-through of the holes in early 1981. Cost data for the sodium silicate grout are also presented.

Jan 1, 1984

By Albert W. Deurbrouck

The performance characteristics of five hydrocyclone coal washers were evaluated to determine the sharpness and efficiency of separation that might be anticipated in commercial operation. The hydrocyclone overflows contained generally good clean coal products that would require little re-treating to remove misplaced high-gravity material. The underflows, however, contained from 63.6 to 36.7 percent of misplaced low-gravity material, which would require secondary cleaning to provide acceptable clean coal yields.

Jan 1, 1974

By P. Cole Gregory, Michael R. Yenchek, John C. Edwards

The U.S. Bureau of Mines investigated the performance of portable power cables under transient conditions. This research had a twofold purpose: (1) to define the thermal characteristics of electrically overloaded trailing cables, and (2) to conceptualize electrical protection for cables that allows maximum cable efficiency without diminishing electrical safety in underground mines. Several tasks were under- taken in support of these goals during the 3-year research effort. Overload tests ranging from 2 to 12 times rated ampacity were conducted in the Bureau's Mine Electrical Laboratory. Two thermal models of energized type G-GC trailing cables were constructed, one based on thermodynamic theory and the other using empirical data from previous Bureau load tests. The empirical model was then incorporated into an interactive computer program that can assist designers and approvers of mining machines in selecting the appropriate size trailing cable. This program can be the basis for a cable protection system that ensures that cables are not the source of fires, ignitions, burns, or explosions underground.

Jan 1, 1993

By James P. Rider, Jay F. Colinet

The National Institute for Occupational Safety and Health (NIOSH) has conducted benchmarking surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify dust generation from major sources and determine the relative effectiveness of the different control technologies. Results from the underground dust surveys will be presented as an update on longwall dust control technology and operating practices.

By R. F. Waters

The Bureau of Mines developed laboratory-scale processes to recover sodium phosphates and metal values from waste sludges generated by the phosphate treatment of automobile and appliance components. After treatment of the sludge with NaOH, followed by coke or hydrogen reduction and sintering, zinc and lead were recovered as fume; the sinter was separated by leaching into a metallic product, chiefly iron and nickel, and high-purity disodium or trisodium phosphate.

Jan 1, 1971

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971

By John C. Edwards, Gene F. Friel

A series of liquid fuel fire experiments evaluated the comparative responses of five types of commercially available smoke detectors and a diffusion-mode carbon monoxide (CO) detector under normal and reduced airflow conditions based upon the alarm times of the detectors. These experiments were conducted in the Safety Research Coal Mine at the U.S. Bureau of Mines Pittsburgh Research Center. Two of the smoke detectors had manufacturer set alarms. For the other three smoke detectors, an alarm point was defined in terms of their background analog signal and the detector's electrical output noise under ambient conditions. A correlation was developed of the travel time of 5 ppm CO between pairs of CO detectors with the travel time calculated from entry and crosscut volumes and measured airflow. Based upon the relative performance of smoke detectors in this limited study, smoke detectors can be as effective as CO detectors for mine fire detection once identifiable alarm values are defined. Implementation of smoke detectors as part of an atmospheric mine monitoring system will improve mine safety.

Jan 1, 1996

By Max J. Spendlove

The secondary copper industry is comprised of numerous enterprises which collectively employ many of the recovery and refining processes now used in primary plants as well as many other processes that are unique to the industry. Effective methods are used for identifying and segregating all types of scrap according to widely accepted standard classifications. Segregated scrap and waste materials usually require some preliminary processing to remove both valuable and deleterious associated constituents. Smelting, melting, alloying, and pyrorefining are common methods used for producing secondary metal, but operating techniques usually differ from primary metal operations because of the difference in physical and chemical properties of the respective raw materials. Some copper scrap is converted to copper chemicals rather than to refined metals or alloys. Recovery efficiencies of all processes are reasonably high, and the quality of products meets rigid specifications.

Jan 1, 1961

By R. Blickensderfer

Maintaining an adequate supply of minerals and metals to meet national economic and strategic needs is the overall goal of the Bureau of Mines, U.S. Department of the Interior. One method of achieving this goal is to conserve scarce metals by cladding a plentiful base metal, such as iron, with a scarcer metal. To investigate cladding, a vacuum-rolling mill capable of rolling bimetal specimens at temperatures to 1,300° C in a residual gas pressure of 2 x 10-5 torr was established. Metals that were successfully bonded to iron included stainless steels, chromium, nickel, nickel alloys, copper, and several refractory metals including molybdenum and titanium. The effects of the rolling temperature, reduction in thickness, rolling speed, and residual air pressure on bonding strength and bend ductility of the bimetals were determined. Optimum rolling conditions produced bimetals with bond shear strength essentially equal to that of the iron base metal.

Jan 1, 1980

By A. A. Cochran

The purpose of this Bureau of Mines research was to investigate the theoretical and practical aspects of using ionizing radiation to promote chemical reactions that are of interest to metallurgists, and to carry out a radiation study of a suitable reaction. The effect of 44,000 roentgens per hour of 120,000-volt X-rays on the chlorination of highly pure mixtures of rutile, carbon, and various catalysts at temperatures up to 540° C. is described. At these low temperatures, recoveries were very low; however, in the eight different systems studied, an increase in yield due to X-rays was statistically significant in two instances and was of borderline significance in a third instance. In the other five systems, the differences in yield were not significant. Impurities and added catalysts caused relatively large variations in the yield of TiC14 from the reaction. Although the catalysts employed were reported in the literature as positive catalysts for the reaction, most of them were negative catalysts for the highly pure system studied. With only one exception, each increase in the purity of the charge resulted in a decreased yield of TiCl4. The experimental results indicate that many substances catalyze the reaction studied and suggest that the differences in reactivity of the charge stocks may be due to their various contents of positive and negative catalysts.

Jan 1, 1962

By Pamplinm J. W.

"INTRODUCTION For the past six years the United States Bureau of Mines in cooperation with the University of Alabama, Tuscaloosa, Ala., the Missouri School of Mines and Metallurgy, Rolla, Mo., and certain operating companies of the Florida land-pebble phosphate district have conducted an investigation to determine the amenability of phosphatic sands to concentration. 4 This paper discusses briefly an investigation of the concentration of fine phosphatic sanads of the land-pebble district of Florida. The process used - namely, the tabling of material previously given a selective oiling treatment - is new in its application to the phosphate industry, although old in principle.The feed to the standard phospidate washery is a hydraulically wined mixture of phosphate pebbles, quartz sand, and clay in which the quartz sand grains are segregated in the fine sizes. Me standard method of concentrating (washing) consists of wet-screening. at about 20 mesh to recover the plus 20-mesh material. 5 Lately some of the washeries have introduced hydraulic classifiers for sizing of the screen undersize to recover the coarser spigot products, but even this additional treatment allows much of the fine phosphate to be wasted."

Dec 1, 1932

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

By E. C. Perkins

This report describes a ferric chloride trap, based on formation of a low-melting sodium chloride-ferric chloride mixture of near-eutectic composition, and its use in chlorination of impure titaniferous materials. The trap is placed in the hot gas stream between the chlorination reactor and the condenser. Virtually all of the iron is removed by the trap. The condensed titanium tetrachloride is free of suspended solids and contains only a trace of iron. Four examples are given of the use of the ferric chloride trap in chlorination of impure titaniferous materials. INTRODUCTION In the Kroll process, ductile titanium metal is produced by reducing titanium tetrachloride with magnesium metal.4/ In commercial practice, titanium tetrachloride is produced by chlorinating titaniferous materials in the presence of carbon.2/ In 1957 most producers were using rutile, and virtually all plants were designed for its use. About four-fifths of the domestic consumption of rutile was imported from Australia. The Bureau of Mines, under provisions of contract DMP-116 with the General Services Administration, studied electrosmelting of domestic ilmenites and titaniferous magnetites to produce high-titanium slags with pig iron as a byproduct. Under the same contract, chlorination studies also were being made of these slags. Smelting was done at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., and chlorination at the Electrometallurgical Experiment Station, Boulder City, Nev.

Jan 1, 1958

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation of a coal mine. The average thickness of coal seams mined in the United States has changed very little in the past 40 years. The first measurement of thickness of bituminous coal and lignite seams was made for 1920, when the average thickness was 5.3 feet.4/ The average thickness for later years was as follows: 1945, 5.4 feet; 1950, 5.3 feet; 1955, 5.2 feet; and 1960, 5.5 feet.5/ Table 1 includes data on number and production of bituminous coal and lignite mines classified by I-foot intervals of seam thickness mined in 1920, 1945, 1950, 1955, and 1960. Though bituminous coal and lignite are mined today from seams of exceedingly variable thickness -less than 2 feet to more than 50 feet - a large majority of the production, 62 percent in 1960, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1962

By V. E. Edlund

As part of a research program for recovering alumina from domestic nonbauxitic resources, the Bureau of Mines investigated a lime-sinter, caustic leach technology for anorthosite. This report discusses the unit operations--feed preparation, sintering, and leaching. Acceptable pellets for the bench-scale sintering studies were prepared from mixtures of minus 200-mesh anorthosite and limestone using water alone as the pelletizing agent. Heating pellets at 1,270° to 1,360° C for periods of 0.5 to 2 hr, followed by a 15-min soaking period at 700° C and cooling to room temperature, produced a sinter that dusted to more than 90 pct minus 65 mesh. The weight ratio of limestone to anorthnsite was critical in producing sinter exhibiting good dusting and leaching characteristics. A ratio of 2.0 was optimum for the bulk samples of anorthosite and limestone used in this research. Leach solutions from lower ratio sinters were unstable; gelation became progressively more severe with higher ratio sinters. Leaching the dusted sinter with 10-pct Na2CO3 at 60° C extracted 85 to 90 pct of the alumina in a product solution containing about 50 g/l A1203. Leach residue in contact with pregnant solution tended to set up as a rigid gel as a result of cementation, comp action, and gelation. The presence of a calcium-sodium zeolite [(Cn,Na2)6?(Al2Si04)12?27-3OH20] in the ungelled residues seemed to be the main difference between gelled and ungelled residues.

Jan 1, 1982

By D. Harrington, F. E. Cash

For a number of years the efforts of the coal -mining industry , as well as of the Bureau of Mines , have been directed largely towards the limitation and prevention of explosions in coal mines . The origin of most explosions is ignition of methane or marsh gas , but the extent and violence of these explosions depend chiefly on the combustible dust present . The Bureau of Mines has conducted a large number of tests on the use of incombustible materials in limiting or preventing widespread explosions . The result of these tests , published in Bulletins 167 and 268 and Technical Paper 386 , proves that incombustible dust can be so applied and maintained in coal mines that the ignition of the mixture of incombustible and combustible dusts , or the propagation of flame by the dust mixture , is impossible ; on the other hand , experience and experiment indicate that watering methods are not reliable as a preventive of general or widespread coal-mine explosions . This report describes the use of " mudite , " a mixture of water and finely divided incombustible soil or dirt applied in some coal mines as a means of attempting to limit or prevent widespread explosions .

Jan 1, 1929

By Clyde M. Pearce

The Lake Superior iron-mining district includes parts of the States of Michigan, Minnesota, and Wisconsin. The laws of each State provide for an industrial commission and for inspection of mines. The following extract from the General Orders on Mines, effective October 25, 1937, issued by the Industrial Commission of Wisconsin, is the only reference to the use of safety catches on mine cages or skips found in the laws and regulations in the Lake Superior iron-mining district: Order 316 - Cages for Hoisting Men. (c) Sides, Gates, and Safety Catches. ***Every cage shall be provided with safety catches of sufficient strength to hold the cage with its maximum load at any point in the event the hoisting cable should break. (d) Testing Safety Catches. The safety catches of cages and skips used to hoist men shall be kept well oiled and in good working order. They shall be tested at least once each month by tying up the cage or skip with hemp rope, lowering a few feet of hoisting cable on top of cage, then cutting the hemp rope, provided that any other system of testing, which is equally effective, may be used.

Jan 1, 1945

By P. A. Kennedy

An environmental assessment or impact statement for onshore waste disposal under the Notional Environmental Policy Act is expected to occur with the development of commercial deep seabed mining. An environmental assessment was conducted in order that testing and refinement of nodule waste disposal techniques can he completed prior to 1988, when commercial seabed mining can begin under U.S. legislation. Within this study three classes of process and four classes of waste disposal technique were identified, and five sites were selected as representative of first-generation nodule operations. Each realistic site/process/disposal technique combination was compared against potential effects to determine important characteristics of the rejects and the sites. Regulatory requirements were also considered at each site to identify important issues and their effect on the permitting process. Principal conclusions in the report are the following: (1) uncertainties exist in the regulatory regimes for hydrometallurgical process tailings, primarily regarding classification as hazardous waste; (2) slogs from nodule processing are expected to be inert and relatively easy to dispose of at all sites; and (3) additional physical and chemical information on properties of rejects from all processes is necessary to predict environmental effects.

Jan 1, 1982

By Lucia Kuizon

The Miranda Pine Roadless Area Review and Evaluation (RARE II) study area (No. 5114) comprises 12,600 acres (5,100 ha) in Los Padres National Forest in Santa Barbara County, California, about 15 mi (24 km) east of Santa Maria (fig. 1). Mineral investigations are made by personnel from the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and sampled mineral properties where appropriate.

Jan 1, 1983