Search Documents

By Manuel Gomez

A lignite from Milam County, Tex., has been oxidized by air at temperatures from about 27° to 300° C. for varying lengths of time. The oxidized coal was carbonized at 500° C. in a laboratory assay unit, and the products of carbonization were measured and analyzed. The data presented suggest that, as lignite is progressively oxidized, tar yields are decreased and gas yields are increased in a ratio approximating 1:1. It is surmised that tar-yielding structures in the nonoxidized coal produce gas, principally, when the coal is oxidized. Char-yielding structures of the nonoxidized coal give rise to additional water of decomposition after oxidation and pyrolysis. As lignite is subjected to greater oxidation, the gaseous product evolved on pyrolysis becomes almost entirely carbon dioxide. Tar yields decrease with an increased degree of oxidation, so that the reduction in tar yield may be used as a qualitative measure of oxidation. Pilot-plant drying and carbonization, where air is used as the transport gas and where some air is included in the drying and carbonizing gases, induces some oxidation of the coal particle. The short residence time in a fluidized system with reference to the oxidation environment limits the oxidation.

Jan 1, 1956

By H. Robert Ensminger

The Belizean economy registered a modest real growth of 1.3% during 1981. The gross domestic product (GDP), based on current prim was $121 million' with an inflation-rate of 10%. The country received $19 million in economic aid during 1981. In early 1981, Belize'e four commercial banks raised the interest on deposits to 15% in an effort to curb capital outflow. During 1981, the financial situation deteriorated somewhat, particularly the balance of payments. For the year the total value of imports exceeded exports by almost $38 million, while the Government continued to maintain a fairly free trade policy. Import duties and term averaged about 8% on essential item and 40% on nonessential ones.

Jan 1, 1983

By Howard P. Hamlin

This Bureau of Mines report is concerned with the testing procedures for evaluating clays, shales, and slates for lightweight aggregates using the rotary-kiln method of production. To meet the increasing demand for light-weight concrete, rapid, accurate methods for appraising raw materials for light-weight aggregate are needed. Preliminary tests were made on samples of clay, shale, and slate, using laboratory equipment, and the data were used to establish operating conditions for pilot-plant-size rotary-kiln tests. Lightweight concrete was made from the processed aggregates and the properties determined. The results show that the laboratory data can be used to guide rotary-kiln testing, and, with the exception of sampling, a complete appraisal of a raw material for lightweight aggregate concrete can be made in 3 days by the methods described in this report.

Jan 1, 1962

By Henry M. Harris

The roll forming of oxide powders was studied in a Bureau of Mines investigation to find the conditions and parameters required to make satisfactory ceramic strip. High-quality porous or dense alumina, zirconia, and porcelain shapes were made by sintering strip roll-formed at room temperature from powders containing minor amounts of binder and water. Strips with thicknesses of 0.04 to 0.08 inch and bulk densities from 40 to 90 percent of theoretical densities were made. The parameters most important to formability were particle size, condition of the powders, and roll gap. Other factors affecting quality were speed and surface condition of the rolls, amount and type of binder, water content, and sintering conditions. Ceramic strip was formed at rates up to 78 feet/minute, which is 13 to 23 times faster than reported by previous investigators, and forming was done in a simple and inexpensive roll unit. Reshaping the strip was possible by cutting, grinding, shearing, and stamping. The following innovations were developed that allow roll processing not normally possible with ceramic powders: (1) Fine-sized powders were made into strip by preparing these as partially sintered granules; (2) thick strip was formed by pressure feeding powders into the rolls; (3) flexible strip was made using a rubber-base bonding agent; (4) corrugated strip was formed on shaped rolls; and (5) porcelain strip was densified and reduced in thickness by rerolling while hot.

Jan 1, 1970

By Kevin Connor

During 1986, the Government continued with efforts to ease the country's almost total reliance on coffee exports for trade revenues by allocating 45% of the Government's budget to commerce and industrial projects. The collapse in coffee prices in 1985 continued to exacerbate the country's growing trade deficit, weakened currency, and dwindling reserves of foreign exchange in 1986. Amoco Burundi Petroleum Corp., a subsidiary of Amoco International Oil Co., continued with plans to drill at least two exploration wells in Lake Tanganyika in 1987. Both offshore and onshore drilling exploration was planned by Amoco Burundi. Any oil or gas finds were expected to have substantial impact on the Burundian economy, as a major portion of the country's trade deficit was directly attributable to petroleum and gas imports.

Jan 1, 1988

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 5/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1962

This report presents test results, data evaluations, and typical system performance expectations based on wireless electromagnetic propagation measurements performed in the MAGMA Copper Company's San Manuel mine near Tuscon, Arizona during March 30 through April 2 1981. In particular, and at the Bureau's request, this work was coordinated with testing of MF prototype vehicular radios being developed by A.R.F. Products, Inc. with USBM support under Contract H0308004 as part of a system to be marketed by Mine Safety Appliance Co. This testing also employed a prototype vehicular antenna developed by Terry S. Cory, P.E. with USBM upport under previous Contract P0382223. The work was performed under USBM contract J0308012, Propagation of EM Signals in Underground Metal/Non-metal Mines. The authors wish to thank Mr. Hank Seany, Manager of Mines and Mr. Bob Zerga, Mine Superintendent who so kindly arranged for the visit. Particular thanks are given to Mr. Al Metcalf who arranged the logistical details of our underground work, and whoa forward thinking program toward improving general mine communications at MAGMA provided the test-bed context for evaluation of the prototype equipment. The authors also wish to thank Benny Jiminez, Paul Ayala, Lorenzo De La Cruz, and Kent Billhartz for their day-by-day support of the testing. Mr. Jiminez's effort was instrumental in performing the testing, and he also provided a detailed understanding of the existing multi-level, multi-frequency trolleyphone system at MAGMA. the authors are also indebted to Dr. Larry Stolarczyk of A.R.F. for numerous detailed consultations on MF technology, and who was present and participated in the majority of the testing. 1.1 GENERAL BACKGROUND ON COPPER MINING AT MAGMA the San Manuel mine is the largest copper mine in the U.S., efficiently extracting copper and molybdenum sulfide from the low-grade San Manuel ore body.This ellipsoidal ore-shell body, with major workings located 2000-3000 feet mbelow the surface, has ore shell thickness varying between 100 and 1000 feet over a longitudinal extent of some 8000 feet, and with major & minor crossectional axes of about 5000 and 2500 feet respectively. The San Manuel mine operation employs in excess of 1000 men/shift with gross ore production between 60,000 and 70,000 tons/day. The mining operation employs the block caving technique; actively being implemented on three levels (2075,2375,2675 feet for haulage, and 2015,2315,2615 product/grizzly levels). The ore haulage is largely via D.C. trolley trains to four (3A,3B,3C,3D) product shafts for skipping to the surface. An additional three shafts at two locations are used to convey men, materials, and developmental rock extractions into and out of the mine. On each haulage level, the trains carry ore an average of two miles one-way from the ore raises to the dump points. 1.2 TOPOLOGICAL BRIEF OF THE HAULAGE LEVELS The 2375 level, on which all the testing was conducted, is illustrated in

Jan 1, 1981

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By F. Varley

Researchers from the National Institute for Occupational Safety and Health (NIOSH), in cooperation with mine operators, conducted a study of heat stress exposures among mine rescue workers in underground mines. Mine rescue workers face extreme heat loads as they enter hot and poorly ventilated environments, particularly when they are wearing breathing apparatuses. The burden of wearing a closed-circuit breathing apparatus (CCBA), the inability to drink fluids for extended periods of time, and the potential for ventilation disruptions and fires combine to increase the risk of heat illness during a response to an emergency. In this research, ambient environmental conditions and heat strain indicators were measured using conventional ventilation monitoring tools during mine rescue training exercises. Heat strain was measured with an ingestible temperature-sensing pill that measured core temperature continuously. In addition, a heart-rate monitoring chest strap was used to indicate physical strain resulting from physical activity and heat. Both core temperature and heart rate data were transmitted to a remote recorder worn by a rescuer and time-stamped. Team activities were also observed to determine the contribution of work rate to a person’s total heat load. The effectiveness of several engineering controls, such as cooling the air inhaled by rescuers through an apparatus, wearing cooling vests, and supplying water through the CCBA masks, were investigated. Administrative controls, such as limiting the duration of exposure and controlling the work rate through forced-rest regimens, were also evaluated. Results to date are discussed, and tools for evaluating team condition and estimating the length of time it would be safe for rescuers to work are proposed.

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

8. Field Demonstration of the Remote Mine Sealing System in a Coal Mine 8. 1 Selection of Field Test Site Eastern Associated Coal Corporation (EACC) offered its Federal No. 1 coal mine in Grant Town, West Virginia as the site for field testing of the remote sealing system. The choice of Federal No. 1 mine was particularly appropriate as the first attempt at fire control by remote sealing was done in this mine in 1963. EACC provided the men and equipment required for much of the initial preparation. Considerable assistance, advice, and background on coal mining technology was given by Mr. William Laird, Vice President for Research and Development, EACC, and by Mr. Lawrence Jackson, Resident Engineer at the Federal No. 1 mine. District 3 USBM office, the West Virginia Bureau of Mines, the Technical Support Group of the USBM, and Local 4047 of the United Mine Workers of America also cooperated. 8.2 Preparation of Field Test Site 8.2. 1 Underground Site Preparation The underground site chosen for the field testing was in a non-working portion of the mine within a few hundred feet of the main haulage road, as shown in Figure 80. Known as "Seven Switch, " this area was a 20 minute walk or 5 minute "jeep" trip from the man-trip shaft. Ten years having passed since this area was actively worked, considerable effort was required for gob clearing, roof bolting, rock dusting, and rejuvenating the track from the haulage road to the test area. Three primary borehole locations were chosen for the test program. Borehole No. 1 was in a straight passageway

Jan 1, 1973

By George H. Johnson

This report describes the procedures and summarizes the results of an investigation of surface subsidence above caving blocks at the San Manuel mine, San Manuel, Ariz., in order to obtain quantitative information on subsidence and ground movement caused by mining large volumes of ore. This investigation is one part of an overall study of rock mechanics being undertaken by the Bureau of Mines. Attention was given to the improvement of a rapid and precise method of surveying a large number of subsidence pins and cracks in the surface terrain. Photogrammetric methods were used as an adjunct to the triangulation subsidence surveying as well as in ordinary topographic work Maps of various kinds were prepared to show the results obtained. The computation of the survey notes was programed for an electronic digital computer at a saving of time and expense over the use of a desk calculator and trigonometric tables.

Jan 1, 1963

By Rodney D. Rosenkranz

The Bureau of Mines evaluated the potential supply of primary copper from domestic mines and deposits and found that increases in copper price will be required in order for many domestic deposits to continue production. As part of the study, a tonnage-price relationship was developed indicating the quantity of copper that could be produced economically from known deposits at various copper prices and at various rates of return on the required capital investment. Costs of production are based on estimated capital and operating costs for mining, concentrating, transporting, smelting, and refining. Direct and indirect operating costs, recovery of investment, and return on investment have been included in the smelting and refining costs. Capital and operating costs are calculated in January 1978 dollars, and byproduct credits are based on January 1978 prices. Known domestic copper mines and deposits contain nearly 92 million metric tons of copper in about 14 billion metric tons of demonstrated mineralized material. These tonnages represent the current domestic copper reserve base. Approximately 74 million metric tons of copper are recoverable from the reserve base using existing technology. Of this quantity, slightly more than 50 million metric tons are economically recoverable assuming a price of 51.00 per pound of copper, credit for the recovery of byproducts, and a 15-percent rate of return on capital investment. Approximately 60 percent of the copper occurs in mines that were producing at the time of the study.

Jan 1, 1979

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsater-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig. Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this typo of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsator-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig.5/ Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this type of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By F. W. Wood

The use of consumable.-electrode arc melting as a production technology is growing. One advantageous feature of this process is that it avoids ingot contamination by soluble crucible materials by employing a chilled metal crucible. Because the thermal balance under these conditions is rather delicate and does not necessarily provide a favorable environment for solidification, catastrophic imbalances can occur. The effectiveness and mechanistic roles of various factors are mostly unknown, and more intelligent insight regarding the distribution of temperature and heat is needed. Experience has provided several pertinent observations, some of which are quite superficial. The most meaningful data have resulted from studies of molten pool shapes and sizes and from measurements of heat flow through crucible walls. Overall experience, intuitively interpreted and supplemented, is sufficient nevertheless as a basis for a boundary-value treatment of the problem. A mathematical analysis based on a separation of variables, using conventional differential equation methods, provides a useful solution. For a cylindrical ingot, the temperature varies as a Bessel function of an argument proportional to the radius and as an exponential function of longitudinal position. Trial calculations using the problem solution seem to verify the general correctness of the result as compared with experience. The role and nature of solution parameters are also clarified, though not entirely resolved. It is revealed that the barrier to heat flow at the ingot-crucible surface has a prominent influence. Utility of the model embodied in the problem solution is readily demonstrated by considering a variety of contemporary questions about arc melting, and it is hoped that utility can be enhanced by improvement of the model.

Jan 1, 1968

By Verne E. Hooker

Stress-relief techniques and instrumentation have been developed through many years of research in the Federal Bureau of Mines and successfully used to determine the in situ state of stress in rock. This paper describes the drilling equipment and accessories for use with the Federal Bureau of Mines three-component deformation borehole gage. Operation and calibration procedures for the deformation gage are discussed in detail. Site selection and overcoring procedures are included to provide a complete working knowledge for surface or underground applications.

Jan 1, 1974

By G. L. Fitzpatrick

A portable optical instrument for performing multispot laser vibrometry is described. The instrument is capable of measuring arrival times, surface motion frequency, and surface velocity and displaying these quantities in various useful ways. Sigma Research is currently pursuing the development of such optical measuring systems for the evaluation of structures in rock by non-contact interferometry methods. This work was sponsored by the U.S. Department of Interior (U.S. Bureau of Mines) under a Small Business Innovation Research (SBIR) contract number J0145075. The goal of the work was to develop a portable tripod mounted measuring system which can be set up at arbitrary distances (up to 30 meters) from a surface and project four in-line laser sample beams on this surface. A light receiving telescope gathers the scattered light from these four spots and provisions are made to mix this light with a reference beam from the laser. Four photodiodes are employed to determine the resultant interference signals which characterize the motion (particle velocity, frequency, amplitude) of the four illuminated spots on the surface under sudy. Information of this type can then be used to characterize the elastic or mechanical properties of the surface in question. In some cases (if more than four spots are involved) this surface information could be back propagated to draw inferences about the internal state of the material volume bounded by this surface.

Jan 1, 1987

By E. D. Calvert

The objective of this research was to examine variations in melting and forging practice for four titanium-base alloys and to determine their effect on the resultant product. Of particular interest was the evaluation of the skull-casting technique. The data should serve as a guide to producers and consumers of titanium products. Physical properties of four titanium-base alloys in ingot form and in sheet form were evaluated and correlated, where possible, with variations in the melting and casting procedure. Consumable-electrode melting was used throughout, but arc current and furnace backfill pressure were varied, and ingots were formed both by melting directly into a water-cooled copper mold and by skull melting followed by pouring into a graphite mold. Alloying metal additions for the alloys tested were (1) 8 percent manganese, (2) 6 percent aluminum and 4 percent vanadium, (3) 6 percent molybdenum and 2 percent aluminum, and (4) 16 percent vanadium and 2.8 percent aluminum.

Jan 1, 1962

By E. D. Gardner

"The town of Ajo is built in the desert and consisted of but a few houses when the New Cornelia Copper Co. started operations. Since there were no stores at Ajo or vicinity the New Cornelia Cooperative Mercantile Co. was established to serve the needs of the employees of the New Cornelia and allied companies.The New Cornelia Copper Co. advanced the money to erect the store building and to buy the stock, and assumes all risks. In all, $85,000 has been advanced, representing the capital stock of the enterprise.The store is run by a store manager appointed by the Copper Company and who reports only to the general superintendent. A committee of seven workmen, representing the various depart¬ments, meet with the store manager monthly and make suggestions for the betterment of the service and, present complaints which have been brought to their attention.The store is well managed, carries a large and well assorted stock and is modern in every respect. Prices are at the same level as in the other Southwestern mining camps. The Copper Company does not particpate in the profits of the store but does receive six per cent interest on the capital advanced. At the end of the year, after making proper deductions for interest on capital account, depreciation of store equipment and fixtures, and, for a proper sum to the surplus account, the rest of the profits is distributed among the employees of the company in proportion to the amount of their purchases."

Aug 1, 1920

By Phillip R. Moyle

Several deposits in the Sheep Hole/Cadiz Wilderness Study Area (WSA) have small identified or potential for undiscovered gold and silver resources. One prospect area is a potential target for molybdenum. Most base and precious metals and one uranium deposit in the study area are of the fissure-filling, contact metamorphic type associated with late stage fluids of the Cretaceous Cadiz Valley batholith. Some evidence suggests limited Tertiary and Quaternary mineralization. Mineral deposits are controlled by faults, shear zones, and joints which strike northwest and dip northeast or southwest. Although undefined, calcium, sodium, lithium, and strontium brines are inferred within the study area. Some potential for oil and gas and geothermal resources is indicated by the interest private industry has shown in the eastern part of the study area. INTRODUCTION The U.S. Bureau of lines and U.S. Geological Survey conducted a mineral survey of the Sheep Hole/Cadiz Wilderness Study Area (p1. 1) which encompasses approximately 205,000 acres (83,000 ha) in south-central San Bernardino County, California. The U.S. Bureau of Mines studied the mineral resources of mines, prospects and mineralized areas; geological, geochemical, and geophysical investigations were conducted by the U.S. Geological Survey.

Jan 1, 1982