Search Documents

By H. Reginald Hardy

This report is Volume II of a three volume final report dealing with the microseismic monitoring of a longwall coal mine. The research presented in Volume II is concerned with the evaluation of field techniques for obtaining seismic velocity data required for computing microseismic source locations. The report describes the evaluation of a number of different field techniques and the seismic velocity data obtained at the Greenwich mine site where the micro-seismic studies, described in Volume I of the final report, were carried out. Three different methods were employed to evaluate seismic velocities, namely; surface refraction, down-hole, and transmission. In all cases the seismic sources were either located on surface (mechanical impact) or near-surface (explosive charges). It was found that a mechanical energy source could be conveniently utilized to determine shallow velocities and make bedrock-regolith interface depth determinations. For deeper velocity determinations suitable explosive charge sources Here required. In general, refraction data did not always plot in a linear manner and some subjective interpretation was necessary. The down-hole method was found to be useful for incremental vertical velocity evaluation, however, the transmission method provided the most consistent average vertical velocity data. At the Greenwich site seismic velocities were found to be anisotropic with values ranging from 9,551 to 10,739 feet per second depending on direction.

Jan 1, 1977

The coal-bearing regions of Colorado cover approximately 29,600 square miles, which is 28.4 percent of the state's total area. The most important coal-bearing regions are located in the north western and west-central parts of Colorado. Coal resources vary from lignite to anthracite. More than 70 percent are bituminous; 23 percent subbituminous; 5 percent lignite; and less than 1 percent anthracite. The state's coal reserves total about 17.2 billion tons, 3.5 percent of national reserves. Approximately 8.8 million acres of coal rights in the state are owned by the Federal Government; on about 72percent of this land, the Federal Government controls both the coal and the surface rights. It is estimated that approximately 4.2 billion tons of coal reserves are under federal ownership in Colorado. Permitted acreage of mines in Colorado ranges from 40 to 13,114 acres. Differences in elevation create many climatic zones in Colorado. Local annual precipitation can average less than eight inches in some areas in extreme western Colorado to more than 30 inches in certain mountainous areas. Generally, precipitation rates are low at most mine sites, making revegetation difficult. Colorado gained primacy when its regulatory program was conditionally approved December 15,1980. The Abandoned Mine Land Program was approved June 11, 1982.

Jan 1, 1992

By R. L. Kidd, T. H. Miller

"INTRODUCTION This paper is the seventh of a series of yearly reviews started in 1921 and pre¬sents information gathered in a cooperative investigation undertaken by the United States Bureau of Mines and the University of Utah. It is the purpose of this report to make available flotation—reagent consumption data and other milling information in such a manner as to be of value to the milling industry and to the manufacturer of flotation reagents.These data have been compiled from a survey of about 300 concentration plants in the United States. Much additional information has been obtained from the various offices of the United States Bureau of Mines. Many of the plants covered in the survey made complete reports of their operations, but others were apparently unable to supply this information in sufficient detail to meet the requirements of this report. As a result, some sections of the report are more complete than others. In general, however, the mill reports were much more complete than in previous years, and for the first time it has been possible to calculate average mill recoveries in the treatment of certain classes of ores. As in the past, every effort has been made to conceal individual plant operations.ACKNOWLEDGMENTSIt is realized that the publication of this information is possible only through the assistance of the mill operators, and the authors wish to express their appreciation of this cooperation. Thanks are also due the various field offices of the United States Bureau of Mines, division of mineral statistics, for assistance in collecting this information."

Aug 1, 1931

By M. J. Ankeny

The expression "firing open, unconfined shots," as used in this circular, means the firing of explosive charges not confined in boreholes. Examples are the so-called mudcap shots, adobe or dobe shots, or bulldozing shots consisting of explosive charges placed on, under, or between rocks for the purpose of breaking them. The practice of firing open, unconfined shots is not uncommon in coal mines, despite the fact that numerous mine explosions and dust ignitions have resulted from this practice. The usual method of preparing such shots is to place the explosive with its detonator on top of a piece of rock or coal and cover it with clay, loam, sand, or road dust; frequently no covering of any kind is used. In some mines, an open charge of explosive is placed on timbers to dislodge them or in crevices in the roof to break down loose rock that cannot be dislodged with a bar or pick. The explosive charges may be made and fired singly, although sometimes several charges are placed on one large piece of rock with a detonator in each charge, and all charges are fired simultaneously. Although it is general practice to use permissible shot-firing devices, which will not ignite gas or dust to fire these charges, electric power from the regular mine circuits is sometimes used. When the shot is fired, any coal dust that may be present is thrown into suspension by the blast and may be ignited by the intense hot flame of the explosive or by an arc or spark at the leg wires or the end of the firing leads if power from the regular mine circuit is used to fire the shot. Even if there is not enough coal dust present to form a dust cloud, open, unconfined shots can readily ignite methane.

Jan 1, 1952

By Walter T. Lewieki

"INTRODUCTION Numerous deposits of iron ore are found in Cherokee, Bartow, Floyd, and Polk Counties in northwest Georgia. The deposits are generally small and irregular in shape. The ore is usually referred to as ""brown ore"" and is predominately limonite. The crude or ""bank ore"" has to be washed and concentrated before being shipped.The proximity of the deposits to the Birmingham furnaces and a favorable freight differential permit the operation of many deposits that otherwise would be uneconomical. The district produced 413,468 long tons of brown-ore concentrates, averaging 45.53 percent iron in 1943.The necessity of developing additional iron-ore reserves for the war energeucy to supplement the production of the Birmingham district, prompted the Bureau of Mines to initiate exploration of the more promising northwest Georgia deposits. Thirteen properties in the four counties were explored during the program (fig. 1).HISTORY AND PRODUCTIONSeveral furnaces were operated in the district until the early 1900's, ranging from charcoal furnaces to more modern plants with capacities up to 50 tons of pig iron. No furnaces have operated for about 40 years, the product being shipped to Alabama and Tennessee.Bartow County iron mining is declining, although formerly it was the principal producer of the district. Most of the known merchantable ore deposits have been exhausted. For the past 3 years the Mitchell-Hodge mine has annually produced about 225,000 long tons of concentrates containing 46 to 43 percent iron and at present is the only large producer in Bartow County."

Jan 1, 1946

By J. D. Davis

From the chemist's point of view it would be ideal if specifications for coke for any stated purpose could be written on the basis of chemical composition and burning characteristics. Unfortunately this is not possible. In fact, the physical properties of a coke are often of such major importance as to render any specified chemical requirements totally inadequate to show the quality of coke desired. For example, a furnace coke may admirably fill all chemical requirements, such as for low phosphorus, sulphur, moisture, and high fixed carbon, and still be too soft to support the burden of the furnace without excessive crushing. Again, a domestic coke though a good fuel as judged from Chemical analysis, may be of unmarketable size. Thus one can not define the quality of a coke for a specified purpose without taking into account both its chemical and physical characteristics even when this has been done the specification may fail because neither coke user nor producer can accurately define by quantitative tests the qualities most desired. In other words, there is need of accurate test methods for measuring the properties of coke and, what is equally important, for correlating the results with the behavior of the coke in use. Coke quality is determined by the kind of coal used, the coking process, and the type of equipment used in the coking process. Chemical analysis of the coals, together with small-scale coking tests, will give a good indication of their suitability; but, in general, coke must be produced on an industrial scale and tested in the equipment for which it is intended before conclusive information as to its quality is obtained.

Jan 1, 1928

Crosson and Peters treat the errors that result in miner location due to errors in the overburden earth model used for computing location. A parallel effort by J. Powell of PMSRC is discussed here, where the location method used is that of the Westinghouse location program - "Miner". This location program was tested by Powell by using arrival times generated from the overburden earth model of Table l* rounded to the nearest millisecond. Location computations were then made using 3 geophones at a time. The average location is tabulated for all geophone triplets except when 3 geophones are in line. Geophone arrays were as shown in Tables 2 and 3. The manner in which the test was done is illustrated in Figure 1. I. SUMMARY OF RESULTS The arrival time differences, based on the Table 1 earth model, together with geophone locations based on the array geometries of Tables 2 and 3, were entered into the computer, together with a stated depth of 700 feet and an estimated overburden seismic velocity of 10,000 feet per second. These parameter values were processed by the location program - "Miner". Figure 2 illustrates the interpretation of the plots and data. The tabular data and plots of Table 4 and Figures 3, 4, and 5 illustrate the location error results obtained. These plots indicate that for sources within the array, the errors are considerably less than the measured errors obtained during field tests of the present location system. The possible reasons for this discrepancy are noted in Part Eight (Earth Models).

Jan 1, 1974

By Jozef S. Stachulak

In This Chapter [Ore pass dust control Drill dust control Blasting dust control Conveyor belt dust control Transfer point and crusher dust control Roadheader dust control and How much ventilation air to use] This chapter discusses respirable dust control in underground hard-rock mines. These mines use a wide variety of extraction methods, but they have many common dust sources and dust control needs. Ore passes, drills, blasting, conveyor belts, transfer points, crushers, and load-haul-dump operations can be major sources of dust. Roadheaders, which are sometimes used in hard-rock mines, produce dust in large quantities. For the most part, dust in hard-rock mines is controlled with ventilation air, water sprays, and dust collectors. It is also important to prevent dust from getting into the air in the first place. Good dust control practices will reduce overall mine ventilation requirements. [Lack of maintenance is the main source of dust problems in hard-rock mines according to Rodgers [1974], who conducted a dust survey of hard-rock mines several decades ago. Rodgers found that spray systems had clogged sprays, dust enclosures had improperly fitted skirts, and ductwork was plugged and had leaks. Today’s mines have better maintenance programs (we think), but when dust levels are high, maintenance is still the first topic to address.] The Mining Association of Canada [MAC 1980] and Knight [1980] provide good general information about hard-rock dust control. For conveyor belt dust control, Goldbeck and Marti [1996] and Swinderman et al. [1997] are valuable sources of information.

Jan 6, 2003

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

By E. R. Maize, R. D. Currie

"Good ventilation is one of the first requisites in the safe and efficient operation of a coal mine. If a mine is gassy, the uninterrupted circulation of an adequate supply of fresh air is imperative if that mine is to operate with a relative degree of safety. That ventilation is not •only a safety consideration, but is an extremely important economic factor is shown by the fact that in many mines 50 per cent of the total power cost is for ventilation.The system used in the Graceton Coal & Coke Co. mine, Graceton, Pa., is believed to be unusual in many ways. Its application in this mine has re¬sulted in good ventilation of the working faces, no interruption to the venti¬lating current through the use of doors. a large- portion of the air circulated by the fan reaching the working places, low velocity air currents on traveling and haulage ways, low water gage and power consumption of the fan, and well-ventilated gob areas.This investigation was made possible through the courtesy of W. H. Robertson, mine superintendent. Fred Roberts, mining engineer, and Floyd Phillippi, mine foreman, assisted in the collection of information.The Graceton mine is a slope, opening the Upper Freeport or E bed, on the Pennsylvania Railroad about midway between Blairsville and Indiana at Graceton, Indiana County, Pa. The production is approximately 1,000 tons of coal per day and about 170 men are employed underground. The mine is considered gassy and was found to be liberating approximately 300,000 cubic feet of methane in 24 hours. The return airways terminate at a circular, concrete lined shaft 12 feet in diameter and about 115 feet deep at which is the exhaust fan.Mining is done by a block system with flat or level entries turned off the main slope at intervals of 1,350 feet, off which the butt headings are turned up the grade parallel to the slope. Rooms, which are about 225 feet long and 12 feet wide, are turned off the butt headings on 80-foot centers, leaving a block about 68 feet thick between rooms.Haulage on the main slope is by rope, with the hoist on the surface. This hoist is electrically driven through a 500-h.p., 2,300-volt motor. The rope used in this haulage is 1-1/8 inches in diameter. There are five electric trolley locomotives - one 10-ton and four 6-ton - which do all of the hauling in the flat and butt entries.Before it is blasted all of the solid coal and as much of the pillar coal as can be cut with safety is undercut by permissible mining machines. Shooting is done by shot firers who use permissible explosives, electric detonators, and dry-cell, nonpermissible batteries.In rooms where conditions are normal, timbering consists of two rows of posts on 4-foot centers. Posts are required to be within 6 feet of the face in machine-cut places and within 3 feet of the face in hand-mined places. Timbering on entries, where required, is of two types: a bar hitched into the ribs and supported by the coal, or 3-piece sets. The legs of the 3- piece sets used on the slope are set well back into the rib to prevent their being. knocked out by a wreck."

May 1, 1932

By Albert L. Toenges

The purpose of this paper is to describe some of the methods and practices of mining coal mechanically where more than one shift is worked, with the view of determining the advantages and disadvantages of various types of equipment and mining systems now in use. This paper is in the nature of a progress report, and, as the number of mines discussed in it is limited, the conclusions drawn in the comparison of various systems are not final but may be revised after subsequent investigations. Physical conditions vary in different and in the same mining districts and determine, more

Jan 1, 1938

By Bryan Buchholz, N. Kumar Kittusamy

Previous studies indicate that operators of heavy construction equipment are afflicted by musculoskeletal injuries of the arms, shoulders, neck, and lower back. These injuries appear to be due to excessive periods of sitting (static posture), work intensity, whole-body vibration, high resistance levers, repetitive motions, and awkward postures. (2-5) Although numerous studies have shown an association between operation of heavy construction equipment and symptoms of musculoskeletal disorders, very little research has been performed that systematically characterizes operating engineers' exposure to ergonomic hazards. The objective of this study was to systematically characterize the ergonomic hazards associated with excavating operations. As such, the following were performed: (1) vibrations were measured at the operator/seat interface (X, Y, and Z axes), and at the floor of the cab (Z axis); (2) psychophysical ratings of whole-body vibration (WBV) level and overall seat design were obtained; and (3) postural assessments of the job were made. Methodology This study evaluated an inexperienced female operator performing excavation, utilizing two different pieces of equipment. The operator was 37 years old, 162 cm tall, and weighed 80 kg. She had approximately 15 hours of operation time (experience) on the equipment evaluated. The two pieces of equipment used were: a Case Super 580E (1986) backhoe/loader, and an Insley H-2000 excavator (1975) (see Figures 1 and 2). More evaluations were performed on the backhoe/loader than on the excavator. The following evaluations were performed on the Case equipment: 1) vibration levels at the seat and floor; 2) psychophysical ratings of the overall seat design and vibration levels (for the task duration, and for an 8 hour duration); and 3) postural assessments. For the Insley equipment, all of the evaluations were performed except vibration measurements. When the evaluations were conducted, the following environmental conditions were noted: the temperature was 31°F, and soil and terrain conditions were rough and frozen.

By Charles L. Kimbell

In broadest overview, UN global industrial production indicators released and shown in table 2 suggest that the extractive sector of the world's mineral industry in aggregate registered a very slight upturn in 1991 relative to its 1990 performance. It also shows a continued rebound in the industry from the recessionary period of the mid-to late-1980's. These same indicators as calculated in late 1991, however, reflected a very minor downturn in extractive mineral industry operations between 1989 and 1990. This latter downturn represented a notable revision from the data reported in the immediate previous edition of this chapter, which suggested a tiny upturn. The apparent slight 1991 upturn in extractive sector industrial output generally was not mirrored in the performance of the processing sectors of the global mineral industry. Although the aggregate index for the chemicals, petroleum, coal, and rubber products manufacturers (see table 3) showed a notable gain in 1991, similar indices for nonmetallic mineral products and for base metals registered declines between 1990 and 1991. Examination of regional performance indices shows that the difficulties experienced in 1990 in maintaining output levels within the countries that formerly constituted the CMEA were reinforced by trends toward reduced gains in output levels, if not actual reductions in output, in several other areas. Generally speaking, the traditional developed market economy countries recorded downswings in overall industrial activity in 1991, particularly after midyear, whereas developing market economy countries logged gains. The developed market economy country downturns, however, were not nearly as significant as were the downturns recorded for the former centrally planned economy states - those that before 1992 were either constituent Republics within the U.S.S.R. or the latter's CMEA partners.

Jan 1, 1993

By M. G. Zabetakis, T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed ms investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

By Ronald W. Schaefer

This report describes operations at the Rosiclare Fluorspar Works of the Aluminum Co. of America at Rosiclare, Hardin County, Ill. The works include the Fairview mine, the fluorspar mill, and related facilities. The publication covers exploration, development, mining and milling practices, mine-drainage problems, and other activities and is presented as part of the Bureau of Mines series of publications on mining and milling practices in various parts of the United States. The Rosiclare fluorspar area, for its size, has been the largest producer of high-grade fluorspar in the United States and probably in the world. The vein system in this area is over 5 miles long and 1/2 mile wide, and ore has been found as deep as 900 ft.

Jan 1, 1961

By S. R. Crane

One Bureau of Mines goal is to minimize the undesirable environmental impacts associated with industrial plants emitting waste gases containing S02. To help meet this goal, a regenerable flue gas desulfurization process was developed. This process, known as the citrate process, uses a buffered weak acid solution to absorb S02 from the waste gas. The absorbed S02 is reacted with H2S to precipitate elemental sulfur and regenerate the solution for recycle. The H2S feedstock for the process, if not otherwise available, may be produced by reacting two-thirds of the recovered elemental sulfur with natural gas and steam. Laboratory investigations and pilot plant operations were conducted by the Bureau to determine if H2S from the natural gas, sulfur, and steam reaction was suitable for the citrate process. The laboratory investigations, in which an H2S generator was integrated with other citrate process operations, provided a basis for design and operation of the pilot plant. The objective of the pilot plant was primarily to provide H2S for the citrate pro-cess pilot plant at the Bunker Hill Co. lead smelter in Kellogg, Idaho. The design capacity of the pilot plant was 0.4 to 1.25 tons of H2S per day. The operation demonstrated that (1) a 77-to 79-dry-volume-percent H2S product could be produced from pilot-plant product sulfur, natural gas, and steam; (2) the product R2S regenerated the SO2-loaded citrate solution; and (3) under certain conditions over 95 percent of the natural gas could be converted to H2S.

Jan 1, 1981

By Leonard J. Prosser, Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

By Forrest T. Moyer

Injury experience at coal mines and mechanical-cleaning plants (excluding officeworkers ) in 1967 was 222 fatal and 10,115 nonfatal disabling work injuries during an exposure time of 241.8 million man-hours. These injuries occurred at a frequency rate of 42-75 per million man-hours worked; the severity rate was 7,699 days lost or charged per million man-hours. Each of these general measures of injury experience was lower than similar data recorded for 1966. Employment at 6,885 coal mines and 569 mechanical-cleaning plants, excluding officeworkers, averaged 139,312 men in 1967. The average number of days worked was 220. Coal production totaled 560.8 million short tons, at rates of 2.32 tons per man-hour and 18.32 tons per man-day. A total of 2,779 onsite officeworkers at coal mines and mechanical- cleaning plants worked 5.2 million man-hours in 1967 without a disabling work injury.

Jan 1, 1972

By R. S. Dean

[In E;encralt the I~8:al:ul',~,C,-J. Div:'sion conducts in\'8stigations relat-ing to the treatment of OrGR o.nd L!\3tallurl..'"lcal prod tctR froJ] t~e condi tion in :hich they are Itinod to t!1e refi!l(,u r.etal, . ' th 'the ob,icct of conserving natmal' resources .e..nd 81:mir..3.tin~ wacte by furn.i:::hir..g :nforInf'_tiou on current methods of metal11:.rgical practice, Tfu'..:.kir..g fund T!l;ntal .;;.otudie'" of metal-lurgical processe~, and de~eloping ~e~ proc6sses O~Q lloys to the point of dewonctrati:r:g the:'..r practicab'lity or va.lue}

Jan 1, 1941

By J. J. Shields

This is the Seventh of a series of publications that describe methods and practices used in mining bituminous coal mechanically.3/ This report deals with the operation referred to in coal mining as continuous mining, and the interest shown by mining companies in this method is the reason for this study. Only continuous mining as it applies to the room-and-pillar system of mining, or a modification thereon, is discussed in detail in this report. Although not always as continuous as the name implies, it is a system of mining in which a machine is used to cut and load coal in one continuous operation without drilling and blasting the coal. With the mining equipment in most general use today, the usual cycle of operation in mining of coal is: (1) Timber, (2) cut, (3) drill, (4) blast, and (5) load. As the phases of this type cycle cannot be performed simultaneously in the same working place, it is necessary to operate from 3 to 7 working places so that at least 1 place is available for coal loading at all times. Even if the schedule of the phases in a cycle is maintained, coal production ceases during the time required to move the loading equipment from one loading place to the next. In 1920 a continuous-type mining machine4/ was installed in an Illinois coal mine to drive entries. Several other companies used these entry drivers for short periods in the following few years. In 1927 a southern Illinois coal company installed 2 of these machines which, in the next 25 years, were reported to have driven over 200 miles of entries. The machines did not attain widespread usage.

Jan 1, 1954