Search Documents

By Raymond M. Stateham

The Bureau of Mines used portable infrared scanners to examine the surface of pillars and faces in the Somerset mine near Somerset, Colo. Zones of temperature buildup, indicative of potential combustion, were detected with the scanners; their existence was verified by temperature measurements with conventional instrumentation. Temperatures of 32° to 6° C were measured on surfaces with normal temperatures of 26° to 35° C. The infrared instruments and techniques appeared to offer a rapid and efficient method for locating potential trouble spots in mines susceptible to fires caused by spontaneous combustion.

Jan 1, 1974

By Will H. Coghill, G. Dale Cole

"INTRODUCTION This paper describes a method for the rational sorting of particles by means of a laboratory batch jig. Its purpose is to show that a material can be reliably appraised for gravity concentration without the drudgery of sink-float fractionations.Development of the batch- jig method of testing was incidental to a study of the Birmingham, Ala., red-iron ores now being conducted by the Bureau of Mines in cooperation with the University of Alabama and the ore-producing companies.APPLICATIONOres and coal are commonly tested for their gravity-concentration characteristics by specific-gravity dissections in heavy liquids. The heavy liquid most commonly used for coal is zinc chloride and for ores they are benzene, carbon tetrachloride, acetylene tetrabromide, methylene iodide, and thallium malonate formate. The last is poisonous and corrosive to the skin but is essential for separations in the 3.3 to 4.4 specific gravity range. The last two of these liquids are expensive, and several of them are hard to obtain now.Although it is not suggested that heavy-liquid dissections be eliminated entirely, sometimes a more reliable evaluation of coal and ore can be obtained by other and more simple means. For example, sink-float data were unsatisfactory as a guide to commercial gravity concentration of a red-iron ore because they did not take into account the difference in particle shape of the hematite and gangue and the differences in true and apparent specific gravity of the hematite grains, some of which were porous. For this ore, the batch-jig method of testing herein discussed proved advantageous. Not Only did the batch-jig data give a truer picture of the concentration problem, but only about one-tenth the time of the conventional sink-float tests was required."

Jul 1, 1944

By W. A. Dunkley

During the past year and a half the Western United Corporation of Aurora , Illinois , has been distributing carburetted water ges from its Lockport , Ill . , plant , to an extensive territory , under an initial pressure ranging up to 90 lb.. per sq. in . The most distant distributing point on the system is at Harvard , Ill . , about 35 miles from the plant.. The territory supplied is approximately 85 miles long and 35 miles wide , the total mileage of rains being 1223 , or approximately 24 per cent of all the gas trains in Illinois outside the city of Chicago .

Feb 1, 1923

By William A. Beck

"The Piedmont Manganese Belt extends from Taliferro County, Georgia, 70 miles in a northeasterly direction through Greenwood County, South Carolina, and conforms with the trend of the Piedmont Province. The total area of the belt is reported to be about 1,000 square miles, and the maximum-width is about 24 miles.Manganese has been known to exist in the belt since 1845. M. Tuomey mentioned a deposit in the Edgefield district on Hard Labor Creek in South Carolina in a report on the geology of South Carolina published in 1848.Ore was first mined about the time of the first World War, when the Colley mine, near Lincolnton, Ga., was. Opened. The only operation in the area at present is that of the Abernathy & Kehaya Mining Co., at McCormick, S. C.The geographical position of the belt is from west longitude 82° 57’, north latitude 33° 39' to west longitude 82° 06', north latitude 34° 08'. The towns of Washington and Lincolnton, Ga., and McCormick and Greenwood, S. C., are in or near the belt.An exploratory project of the Bureau of Mines was started on the McCormick, S. C., deposit in April 1944, and trenching, test pitting, and hand-auger drilling-were done on a small scale until early in October 1944. (Fig. 1.) In November 1944 work was begun on a property 12 miles north of McCormick, known as Parsons Mountain, which is leased to M. H. McKnight by the United States Forest Service. From March 15 to March 24, 1945, work was done on the property of Mrs. H. B. Ross, which is known as the Morgan farm.The Abernathy & Kehaya manganese mine contains what is locally known as the Dorn gold mine; mineral rights on the property were owned by M. G. & J. J. Dorn, Inc."

Apr 1, 1946

By J. E. Wilson

A bench-scale expansion tester using 71 grams of coal was developed to determine the practicability of an apparatus of this size to investigate the effect of variables such as oxidation, blending, bulk density, inerts, size consist, petrographic differences, and rate of heating on the expanding properties of coal. The value of this tester is shown by the correlation that exists between its results and those of the larger scale sole-heated oven expansion apparatus used in commercial plants. From tests on 32 coals the standard error of estimate for predicting sole-oven results from bench-scale results is ± 5.3 percentage points. A standard deviation of the difference between pairs of tests in the latter apparatus of ± 2.1 percentage points was determined for 31 samples. In the sole-heated oven test the expansion of a coal at constant pressure is directly proportional to the dry coal bulk density. Tests in the bench-scale tester show a similar relationship between expansion and bulk density. When the blending ratios of high-and low-volatile coals are varied, similar changes in expansion are observed in both the sole-heated oven and the bench-scale tester. Therefore, the effect of other variables on expansion should be similar in the latter apparatus.

Jan 1, 1960

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which type of plant utilizes more than the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which credo oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining.

Jan 1, 1935

By D. A. Reynolds

The Bureau of Mines-American Gas Association survey of the carbonizing properties of American coals was begun in 1929, and has been continued almost without interruption since that time. Upwards of 100 coals have been carbonized at low, medium, and high temperatures in this survey, and about 200 additional coals have been carbonized at high temperatures only. All survey coals were blended with coal of different rank for carbonization at one high temperature (900° C,). During the past few years, 12-high-volatile A coals were blended with Pocahontas No 3 coal from Kimball, McDowell County, W. Va., and in this report the physical properties of the cokes from these high-volatile coals and their blends are compared.

Jan 1, 1949

By Claire C. Caruso, John M. Russo, Jennifer M. Schmit, Robert B. Dick, Edward M. Hitchcock

PURPOSE This report provides an integrative review of 52 recently published research reports that examine the associations between long working hours and illnesses, injuries, health behaviors, and performance. The report is restricted to a description of the findings and methods and is not intended as an exhaustive discussion of all important issues related to long working hours. Findings and methods are summarized as reported by the original authors, and the study methods are not critically evaluated for quality. SUMMARY In 16 of 22 studies addressing general health effects, overtime was associated with poorer perceived general health, increased injury rates, more illnesses, or increased mortality. One meta-analysis of long work hours suggested a possible weak relationship with preterm birth. Overtime was associated with unhealthy weight gain in two studies, increased alcohol use in two of three studies, increased smoking in one of two studies, and poorer neuropsychological test performance in one study. Some reports did not support this trend, finding no relationship between long work hours and leisure-time physical activity (two of three studies) and no relationship with drug abuse (one study). A pattern of deteriorating performance on psycho physiological tests as well as injuries while working long hours was observed across study findings, particularly with very long shifts and when 12-hour shifts combined with more than 40 hours of work a week. Four studies that focused on effects during extended shifts reported that the9thto 12th hours of work were associated with feelings of decreased alertness and increased fatigue, lower cognitive function, declines in vigilance on task measures, and increased injuries. Two studies examining physicians who worked very long shifts reported deterioration on various measures of cognitive performance. When 12-hour shifts combined with other work-related demands, a pattern of more adverse findings was detected across studies. Six studies examining 12-hour shifts combined with more than 40 hours of work per week reported increases in health complaints, deterioration in performance, or slower pace of work. Two studies com-paring 8- and 12-hour schedules during day and night shifts reported that 12-hour night shifts were associated with more physical fatigue, smoking, or alcohol use. Two studies examining start times for 12-hour shifts reported that decrements in alertness or more health complaints were associated with early 6:00 a.m. start times. One study examining 12-hour shifts in hot work environments reported a slower pace of work as compared with shorter shifts. Another study examining high workloads during 12-hour shifts showed increased discomfort and deterioration in performance as compared with shorter shifts. More definitive statements about differences between 8-hour and 12-hour shifts are difficult because of the inconsistencies in the types of work schedules examined across studies. Work schedules differed by the time of day (i.e., day, evening, night), fixed versus rotating schedules, speed of rotation, direction of rotation, number of hours worked per week, number of consecutive days worked, number of rest days, and number of weekends off. All of these factors could have interacted with overtime and influenced study results. Also, some studies did not report how many hours participants worked per week or other details about the work shifts, which complicated the assessment of their results. The many

Jan 4, 2004

By N. E. Hanna

To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain safety tests prescribed by the Federal Bureau of Mines. These tests are described in Schedule 1-G4/ (explosives) and Schedule 26A5/ (blasting devices). An explosive or blasting device that passes the appropriate tests is placed on the active permissible list. As this list is subject to continuous revision, it has been the practice of the Bureau of Mines to publish periodically the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. The present circular gives all explosives and blasting devices on the active permissible list as of December 31, 1957, and shows all changes, additions, and transfers in that list between December 31, 1951,6/ and December 31, 1957.

Jan 1, 1958

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel.oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which typo of plant utilizes more thou the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which crude oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining. Although no outstanding technical developments of a fuel-saving nature were made in 1934, some progress undoubtedly was recorded. Heat exchangers, an effective fuel-saving device, wore enlarged, and some refiners now take off several cuts before the crude reaches the pipe stills. The total capacity of pipe stills increased 2.5 percent in 1934, and many of the less efficient shell stills were torn out.

Jan 1, 1935

By Robert Goldstein

A computer program for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. To provide a data base for these calculations, eleven 3-D machine models were prepared and the outputs of three luminaire types were measured. Calculations were done for thirty different configurations.

Jan 1, 1977

By G. R. Hopkins

Although many small refineries were dismantled in 1934 the total number of plants, including a few under construction, increased from 604 at the beginning of the year to a new high of 638 on January 1, 1935. The capacity also reached a new record, the total of 4,072,400 barrels of crude oil daily being about 45,000 barrels higher than the previous high of January 1, 1932. The number of refineries increased materially in 1933, following construction in east Texas and the building of many small plants in the Rocky Mountain district and elsewhere. Most of the new plants of 1933 were built to provide an outlet for crude or because the ratio between crude oil and gasoline prices appeared conducive to profits However, low gasoline prices and increased costs in 1934 dispelled the hopes for profits; many plants were shut down, and some were dismantled. The number of operating plants declined from 454 on January 1, 1934, to 435 on January 1, 1935, but the number of inactive plants increased from 137 to a new high of 196 during the same period. As indicated above, new construction was at a minimum in 1934, and on January 1, 1935, only 7 plants were being built.

Jan 1, 1935

By Christopher D. Risbrudt

In this comprehensive study of the use of wood products in coal mining, a sample of over 220 mines provided data by questionnaire. Wood use per ton of underground coal was found to vary substantially by mining process and region. In the Eastern Coal region, 1.6 board feet of wood was used per ton of coal, wel above the 0.6 board feet usage per ton in the West. The kind of timber used varied also by Region. Hardwood use is about 40 times greater than softwood in the Eastern Region. There, hardwoods are plentiful, relatively cheap and strong. In the West where softwood forests predominate, softwoods were 2-1/2 times more common in mine wood use than hardwoods. Nearly 80 percent of the wood used in underground coal mines is used in cross bars and props. Nearly 54 million cubic feet of wood products were used in coal mining in the sample year 1979; about twice as much going to underground mines as surface mines. Wood requirements for mining were projected to 2030 for a range of three oil price scenarios. Much greater wood use will be required for greater coal output.

Jan 1, 1982

By Thomas C. Atchison

The purpose of this Bureau of Mines investigation was to measure the amplitude and shape of the strain pulse and the size of the crushed zone produced in a granite by different explosives and to determine how these quantities are related to the detonation properties of the explosives. The reflection theory of rock breakage has shown that the amplitude and shape of the strain pulse incident at a free surface determine the fragmentation and volume of rock broken. Determination of the properties of an explosive that control the characteristics of the strain pulse produced in the rock will help in evaluating explosives for use in blasting. The investigation showed the different explosives produced a twofold variation in the amplitude of the strain pulse but little variation in the shape of the pulse. The explosives also produced a twofold variation in the volume of the crushed zone, but differences among the explosives were more accurately determined by strain-amplitude measurements than by crushed-zone measurements. The peak amplitude of the strain pulse and the volume of the crushed zone correlated with the calculated detonation pressure of the explosive.

Jan 1, 1959

By J. W. Griffith, J. L. Stauffer, L. M. Demers, D. C. Kuhn, S. Riliog

"The relative activation of eicosanoid production which results from the exposure of the alveolar macrophage (AM) to mineral dusts is thought to be a key factor in the pathophysiology of occupational lung disease. We compared in vitro basal and silicastimulated production of prostaglandin E2 (PGE2) and thromboxane A2 (TXA2) by AM from normal humans and non-human primates (Macaca nemistrina). In addition, we instilled mineral dusts directly into one lung of the non-human primate and evaluated AM eicosanoid production at two week intervals following dust instillation. Unstimulated AM from humans produce more PGE2 and TXA2 than do AM from M. nemistrina. However, in vitro exposure of AM from both species to silica dust produced a qualitatively similar increase in TXA2 production accompanied by no change in PGE2 production. Sequential analysis of AM eicosanoid production following a single bolus exposure to bituminous or anthracite coal dusts, titanium dioxide (Ti()i) dust or crystalline silica showed marked variability among individual non-human primates in qualitative and quantitative aspects of dust-induced eicosanoid production. However, the rank order of potency of the different dusts (silica> anthracite> bituminous) correlated with epidemiological evidence relating the type of dust mined to the incidence of pneumoconiosis. These studies suggest that the non-human primate may serve as a model for the study of both the role of eicosanoids in the etiology of dust-induced occupational lung disease and the biochemical basis for individual variability in the response of lung cells to mineral dust exposure. IntroductionOccupational inhalation of mineral dust can lead to chronic debilitating lung disease ( 1,2). One of the key components of the disease process is thought to be the interaction of mineral dust with the alveolar macrophage (AM) and the subsequent release by the AM of inflammatory and fibrotic substances (3,4). Chronic inhalation of mineral dust, depending on the type and amount of dust, may then produce a situation in which ongoing inflammation, accompanied by the destruction of functional lung tissue by products of activated AM and polymorphonuclear neutrophils, stimulates the production of nonfunctional matrix by lung fibroblasts.The AM produces several oxygenated derivatives of arachidonic acid (AA) which may play important roles in dust-induced lung pathophysiology (5,6). In previous studies in the rat, we found that prostaglandin E2 (PGE2). thromboxane A2 (TXA2) and leukotriene 84 (L TB4) were the major AA metabolites produced by AM (7). PGE2 is associated with pro-inflammatory activity (8) as well as anti-fibrotic activity since it downregulates interleukin -1 (IL-1) and tumor necrosis factor (TNF) release by AM (9-11). TXA2 is known to stimulate platelet activity, cause bronchial and vascular smooth muscle contraction (12) and to possess chemotactic activity (13). LTB4 is chemotactic for neutrophils and monocytes (14) and has been suggested as an additional regulatory factor in the release of TNF by AM exposed to silica dust ( 15)."

Nov 1, 1995

By Aldo L. Furno

Sufficient quantities of combustible vapors are released by some sulfurs to produce flammable atmospheres under prolonged storage. Hydrogen sulfide and carbon disulfide appear to be the principal flammable constituents in the vapor space above molten sulfur. If sufficient carbon disulfide is present, ignition of the vapor-air mixtures can occur spontaneously on contact with the heated surfaces found within storage tanks.

Jan 1, 1963

By L. H. Adami

This paper reports the results of solution calorimetry conducted to obtain the heats of formation of crystalline FeS04?6.952H20 and FeS04?1.008H20, from. which values were derived for the stoichiometric compounds FeS04?H20 and FeS04?H20. Also included are derived values of the free energies of formation and dehydration. This work was undertaken primarily to fill a need for data for pure, easily obtainable ferrous compounds that are suitable for use as calorimetric intermediates, The ferrous sulfate hydrates meet the essential requirements for this use.

Jan 1, 1963

By S. L. Payne, E. F. Foerster, C. W. Schultz, G. R. Zellars

The vapor pressure of copper in a series of liquid copper - nickel alloys was determined by the carrier gas method . The activity and activity coefficient of copper were calculated over the entire range of alloy composition . These data show a slight positive deviation from ideal behavior . The activity coefficient of copper was highest ( 2.10 ) at 0.05 mole fraction copper and approached unity at concentrations above 0.85 mole fraction copper . The results for nickel were calculated from the copper data by the graphical integration of the Gibbs - Duhem equation .

Jan 1, 1964

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

By M. H. Kersten, G. A. Brady, Jerry W. Ramsey

Anthracite samples were oxidized with nitric acid to prepare products representing intermediate stages of oxidation . Similar oxidizing conditions affected different anthracites to varying degrees as characterized by peptization behavior with 0.1 N NaOH . Techniques used in attempts to separate and characterize the products included esterification , absorption spectrophotometry , sublimation , chromatography , electrophoresis , metal salt formation , and solvent extraction . Mellitic acid , either free or in the form of metallic salts , was identified in the acid- soluble products from 10 tests in which the anthracite was treated with nitric acid for periods varying from 24 to 1,000 hours . pentacarboxylic acid was also found in some products . Other benzene carboxylic acids were not present in amounts detectable by the methods used in this study . The acid- insoluble residue from nitric acid treatment varied significantly in solubility behavior toward different classes of solvents . The most effective ones tried included polar oxygenated solvents and pyridine . Infrared spectra of the extracted material indicated that similar compounds were extracted by the different solvents . Aliphatic amines and aniline peptized the residue and o- toluidine reacted with it . Organic material separated from the residue by peptization with dimethylformamide contained 1 percent ash , consisting of more than 50 percent zirconium .

Jan 1, 1964