Search Documents

By E. A. Mihok

A pilot plant for treating mine drainage by neutralization with limestone was designed, fabricated, and operated by the Bureau of Mines. The process consists of (1) producing a very fine (minus 400-mesh) limestone slurry, (2) mixing the slurry with the mine water, (3) aerating the resulting mixture to remove carbon dioxide and precipitate iron, and (4) separating the solids from the liquid by sedimentation. A mine discharge of pH 2.8, containing 1,700 ppm total acidity, 36 ppm ferrous iron, and 360 ppm total iron, was treated at rates from 300 to 400 gpm. The treated water ultimately reached a pH of 7.4 and contained no detectable iron. The resulting sludge compacted to approximately one-third the volume of sludge from mine water neutralized with lime. The advantages of the limestone process, compared with the conventional lime process are as follows: Widespread distribution and lower cost of run-of-mine, indigenous limestone; simplicity of plant design; reduced hazards and plant operating and maintenance costs accruing from the use of a less reactive chemical agent; higher solids concentration of the precipitated sludge; and no deleterious effect caused by accidental overtreatment. While total process costs could not be determined, it is conservatively estimated that the cost of treating mine water by the limestone process is one-third to one-half the cost of the lime process, depending on the characteristics of the water to be treated and the availability and quality of limestone used.

Jan 1, 1968

By J. M. Singer

The Bureau of Mines investigated the threshold of dispersal of monolayers and piles of rock dust, anthracite, and Pittsburgh seam coal dust in a small wind tunnel that simulated a coal mine gallery, with the objective of preventing or limiting the formation of flammable dust clouds. The effect of selected variables on entrainment velocity was examined. Mode of entrainment and flow processes in the wake region of dust configurations were investigated by means of high-speed motion pictures. Significant results were as follows: 1. Local minimum air velocities required for dispersal were only slightly higher for shallow dust ridges than for dust particles. 2. Minimum velocities for entrainment of dust particles from smooth glass and coal surfaces increased in the order rock dust, anthracite, Pittsburgh seam coal. 3. The mechanism for dispersal of dust poles depended significantly on dust pile geometry, cohesiveness of dust, bulk density and compaction of dust, adhesive surface, and vibrations perturbing the supporting surface.

Jan 1, 1969

By Sean Gallagher, Gene Wilson, Christopher Mark, Craig S. Compton, Gregory M. Molinda

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers’ compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

By R. S. McClain

The Federal Bureau of Mines investigated residues from aluminum plants, to determine if carbon could be removed by flotation while recovering fluorine and aluminum compounds for recycling to the reduction process. This publication summarizes studies on samples representing three types of plant waste products, supplied by three aluminum-producing companies. Samples of flue dust, pot skimmings, and pot linings from the various plants all responded to a simple turpentine flotation scheme to reject 90 to 97 percent of the carbon. Aluminum compound recoveries ranged from 42 to 94 percent on the flue dust, were about 95 percent on the pot skimmings, and ranged from 75 to 89 percent on the pot linings. Fluorine recoveries from the same samples ranged from 35 to 63, 92 to 95, and 77 to 86 percent, respectively. The pot linings contained soluble salts of aluminum and fluorine which were recovered by precipitation with sodium aluminate and carbon dioxide gas. Composites of residues from each plant responded to flotation much the same as the individual samples. Aluminum is produced by the electrolysis of alumina in a molten cryolite bath. The electrolytic reduction cell consists of a carbon-lined box containing a pad of molten aluminum which serves as a cathode, a carbon anode, and an electrolyte of molten cryolite in which the alumina is dissolved. Alumina is reduced to aluminum at the cathode, and carbon is oxidized at the anode.

Jan 1, 1961

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By R. J. Hundhausen

The Takilma-Waldo copper district in Josephine County, Oreg., was studied by the Bureau of Mines from September 1950 to April 1.951 and from December 1953 to April 1954. Funds for the investigation were provided by the Bureau of Mines and the California-Oregon Power Co., Medford, Oreg., on a cooperative basis. The copper mines in the district are credited with a total production of ore worth $1,700,000. Since 1933 the mines have been unproductive and, except for minor exploration, largely inactive. The history of the district indicates that the copper deposits were mined principally during periods of high metal prices.

Jan 1, 1956

By K. L. Paciorek

The aim of this program was to develop a reliable and meaning-ful basis for assessing certain safety aspects, namely fire and, in particular, toxicity hazards of articles employed in underground coal mining operations. The present investigation was concentrated on the thermal oxidative degradation of representative hydraulic fluids. To achieve this goal all products formed on thermal oxidative degradation of the fluids studied were analyzed, identified I and the amount of each individual species present was determined quantitatively on a weight of product per weight of material basis. The weight/weight data thus obtained can then be factorized to reflect the relative toxicity of each individual species present, using for example the Threshold Limit Values adopted by the American Conference of Governmental and Industrial Hygienists, whereby an overall "toxicity index" can be arrived at which makes it possible to compare the different fluids and/or classes of fluids in a quantitative manner insofar as their toxicity is concerned.

Jan 1, 1976

By Ludwig Schmidt

Large quantities of gasoline are lost each year by evaporation from bulk-storage station tanks. The rate of evaporation from bulk-station tanks is influenced by two principal factors: First, the vapor pressure of the gasoline in the tank; and second, the amount of "breathing" of the tank. The vapor pressures of the gasoline govern the amount of the gasoline vapor in the air-vapor mixture above the gasoline in a tank at a given temperature. This is one of the principal factors in determining the total pressure of the air-vapor mixture within the tank. The "breathing" of the tank is caused by the inflow of air from the atmosphere during certain periods of the day and the expulsion of the air-vapor mixtures at other times, caused by atmospheric variations. The pressure built up within a tank and the amount of gasoline in the air-vapor mixture are both a direct function of the temperature existing within the tank. Therefore, two of the most common methods for reducing evaporation losses from bulk-station tanks are: (1) The use of vapor-tight tanks equipped with relief valves and operated at 1 or 2 ounces of pressure and about 1/2-ounce vacuum; (2) reducing the temperature of tanks and their contents by painting them a light color, by insulation, and in some instances by using water sprays. Water sprays, although effective, usually are too expensive to operate economically. In order to determine and compare the effects of various colors, insulation, and pressure in reducing the evaporation losses of gasoline held in storage in bulk-storage tanks, the Bureau of Mines made observations from May 29 to October 15. 1930, on five horizontal tanks of 12,000-gallon capacity each, which were erected at the plant of Black. Sivalls and Bryson Manufacturing Co., Kansas City, Mo. This report gives in detail the results of these evaporation tests.

Jan 1, 1931

By D. J. Singleton

Erosion corrosion of 12 alloys in phosphoric acid waste water was studied by the Bureau of Mines. Tests were conducted on oblate spheroids or cylindrical specimens in 12-and 60-cm-diam ball mills by grinding phosphate rock in gypsum pond water with a starting pH of 1.6. For comparison, tests were conducted while grinding phosphate rock in plain water. Static corrosion tests in gypsum pond water also were conducted. For all alloys, the wear by erosion-corrosion (milling with gypsum pond water) was greater than the sum of erosion (milling with water) plus static corrosion. Erosion-corrosion wear was about 1,500 to 3,000 mpy for the alloyed white cast irons, 1,000 to 1,400 mpy for commercial steel ball material and type 316 stainless steel, and 600 to 900 mpy for nickel-base alloys and a high-manganese, nitrided stainless steel. Alloy costs per unit of phosphate rock 'processed favor a low-alloy, high-carbon steel or a high-manganese, nitrided stainless steel.

Jan 1, 1985

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By A. L. Toenges, F. A. Jones, J. N. Sxudder, E. R. Maize

"INTRODUCTION This report is the second of a series of studies of analysis of energy requirements and characteristics of various machines used in the production of coal in underground mines and the losses in distribution of energy to these machines. The test equipment used in these studies is described in Report of Investigations 3615. 7/ The preliminary study data and results of tests made on various types of mechanical-leading cutting, and transporting equipment at two mines. This report is analysis of the energy requirements of the energy requirements of the underground equipment of a third mine. An analysis of the use of energy and its distribution usually requires in a saving in energy consumption and the reduction of hazards. The distribution system should be designed to supply energy effectively and study for the efficient operation of all machines."

Feb 1, 1943

By J. Mitchell Linnet

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of deposits in the Bucks Lake and Chips Creek RARE II areas in Plumas and Butte Counties, California. These areas lie along the west slope of the Sierra Nevada on opposite sides of the North Fork Feather River and encompass an area of 62,800 acres (25,400 ha). Metasedimentary and metavolcanic rocks of the Pennsylvanian Calaveras Formation are intruded by plutons of Mesozoic age. Mineral; of economic iterest are in quartz veins in metasediments close to these plutons; they are principally gold and silver with minor amounts of copper, lead, and zinc minerals. Molybdenum, copper, silver, and tungsten minerals occur in tactite along metasedimentary-granitic rock contacts. In both areas, auriferous Tertiary channel gravels have been extensively developed. Asbestos occurs in ultramafic rocks in both areas, and a limestone deposit was explored in the Chips Creek area. Gold is the principal economic mineral in the Bucks Lake RARE II area. The Shenandoah Mine (fig. 1, no. 19) contains 7,500 tons (6,800 t) of indicated and inferred subeconomic gold resources in sulfide-bearing, silicified metamorphic rocks of the Calaveras Formation (table 1). Similar rocks have yielded gold at the Edman and Megowen Mines, adjacent to the area. A high potential exists for additional lode resources in the area around the Shenandoah Mine. Callahan Mining Corporation personnel believe a multi-million ton disseminated gold deposit underlies the property.

Jan 1, 1983

By Walter C. Lorenz

In connection with its renewed study seeking solutions to problems created by release of acid water from bituminous coal mines, the Bureau of Mines recently surveyed reports already written on the subject. This publication is based on that search. The Problem Poor distribution of water is evident on an ordinary geographic map of the United States. The more abundant supplies of surface water appear to be centered in the northeast, the southeast, and the central humid areas of the country. It is in the midst of this abundant surface water, in the Ohio River Valley, that most of the bituminous coal is mined. Varied industry has located in the valley to use the coal and the river. The coal is a source of power and o raw material. The river provides transportation for raw and finished materials; equally important, it provides the water that is used for cooling and processing in manufacturing. It also serves as a vehicle for the disposal of waste.

Jan 1, 1962

By F. R. McDonald

This report presents a discussion of the spectra of 39 condensed thiophenes in which the structure includes at least 1 benzene ring. The vibrational bands present in three regions of the infrared spectra of these thiophenes were interpreted by comparing the similarities of the spectra of condensed thiophenes with the spectra of substituted benzenes. In the overtone-combination region 23 of the 39 condensed thiophenes had spectra which contained sufficient detail to be usable for correlating this region of the spectrum with the appropriate benzene spectrum. In the in-plane deformation region it was possible to make correlations for the vibrations of 18 of the 39 condensed thiophenes whose infrared spectra were studied. In the out-of-plane deformation region the C-H out-of-plane vibrations for hydrogen on benzene rings in the condensed thiophenes can be correlated using known data from substituted benzenes.

Jan 1, 1967

By Abdurrahman Cetinbas

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By Gerald W. Elger

To determine the feasibility of removing nonferrous metal impurities from automobile scrap by thermal treatment in a rotary kiln, the Bureau of Mines conducted four series of tests with synthetic scrap mixtures heated at various temperatures under oxidizing and reducing conditions. The treated scrap mixtures were melted in an electric-arc furnace and cast into small ingots for impurity evaluation. Analyses showed that the ingots were essentially free of residual metal impurities except for copper. Test data indicated that in an oxidizing atmosphere the percentage of copper removed increased with treatment temperature. Percent of copper removed in a reducing atmosphere was found not to be temperature dependent. A significant finding was that copper was embrittled under some of the operating conditions and was mechanically removed by fragmentation.

Jan 1, 1968

By Kenneth Eilerts

The development and operation of "combination wells"5/ have created new and unusual problems, many of which can he solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to know, whether liquid will be formed in the reservoir as a result of isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how pressure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios off gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and. pressure of the system are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the Fluids under reservoir conditions are particularly important at this time, To meet the immediate requirements of the industry for such experimental information, an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date have been accumulated, it may be possible to make dependable estimates of the phase relations for high gas-liquid ratio fluids at the pressures anti temperatures characteristic of "combination-well? reservoirs.

Jan 1, 1940

By E. G. Baglin

As part of an effort to decrease U.S. dependence on imports of critical and strategic metals, the Bureau of Mines investigated three leaching methods for extracting the base metals and recovering platinum-group metals (PGM) from matte prepared from Stillwater Complex flotation concentrates. Because of a limited supply of natural material, synthetic matte of composition similar to matte prepared from natural concentrates was used to devise the extraction sequences. The validity of the sequences was verified with matte prepared from Stillwater concentrates. In two-stage matte leaching, first-stage H2S04 leaching extracted 99 pct of the nickel and iron from the matte but negligible amounts of copper and PGM. Second-stage oxidative leaching with Fe2(S04)3 or FeC13 solubilized more than 98 pct of the copper and no precious metals. Sequential leaching, in which acid and oxidizing lixiviants were added sequentially to the matte without an intervening filtration step, extracted 99 pct of the Fe, Ni, and Cu. A roasting-leaching technique, in which the residue from first-stage leaching was roasted between 360° and 500° C before a second leaching with H2S04, solubilized 98 pct of the copper. The three leaching methods yielded high-grade PGM residues containing more than 98 pct of the PGM in the matte.

Jan 1, 1982

By W. L. O'Brien, E. A. Rowe

Electrorefined vanadium with additions of up to 5 percent by weight of yttrium, cerium , lanthanum , praseodymium, neodymium, and samarium was melted to ingots in a nonconsumable electrode arc in a helium atmosphere . The ingots were rolled into strips and evaluated for the effect of the alloying elements on hardness , tensile strength , ductility , recrystallization temperature , and microstructure . Except for samarium , average additions of alloying elements of 1 to 2 weight - percent resulted in the retention of 0.12 to 1.05 weight - percent in the alloys and reduced the ultimate tensile strength from about 48,000 to approximately 30,600 psi . The corresponding yield stress (0.2 percent offset ) was reduced from about 40,700 to approximately 20 , 200 psi . Diamond pyramid hardness (DPH) was reduced from 117 to an average of 62 kg /mm² . Increased malleability at room temperature resulted with yttrium and all rare - earth- metal additions , except samarium , particularly with more than 0.25 weight - percent additions . Decreasing oxygen contents corresponded with the changes noted in the mechanical properties of the alloys . The recrystallization temperature of electrorefined vanadium was reduced from approximately 950 ° to 800 ° C. Yttrium or a rare- earth metal content , except samarium , in excess of 0.1 weight - percent in vanadium produced a second phase suggestive of an eutectic which indicated a possible maximum solubility of less than 0.1 weight - percent for both room and elevated temperatures .

Jan 1, 1964