Search Documents

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By John J. S. Sebastian

A laboratory-scale investigation was made of the basic problems involved in developing a ceramic heat exchanger to operate at high temperatures for using nuclear heat from gas-cooled process-heat reactors. Technical data were obtained on transferring heat by forced-convection from helium to air in a single-tube vitreous-alumina heat exchanger. Coolant air was passed through the annulus parallel with, and either concurrently or counter to, the flow of helium inside the tube. The data obtained pertain to removing heat from the helium. Average inside film coefficients were determined at mean surface temperatures of 200° to 1,570° F., inlet-gas temperatures of 1,450° to 2,665° F., and Reynolds numbers up to 560. The gas-to-surface temperature ratios were varied from 1.05 to 7.6. The tabulated results are shown in the appendix at the end of this report. The film coefficients of heat transfer were correlated by taking into account the physical properties of the helium at the average fluid temperature. With experimental conditions pointing to a laminar flow, the Nusselt number was found to decrease as the ratio of gas-to-wall temperature was increased to a value of 3. However, within the range tested, gas-to-wall temperature ratios above 3 did not affect the Nusselt number, regardless of the value of the Graetz number. Thus, beyond this point any increase in this ratio ceased to influence the heat-transfer relationship.

Jan 1, 1962

By R. R. Faddick

Properties of coal-water slurries were studied in two separate phases: a rheological phase and a pipeline phase. The purpose of the study was to investigate the rheology of fine coal slurries to determine the effect of fine particles in a coal-water mixture on the economic and operational aspects of a slurry pipeline. The slurries consisted of 6x10, 100x200, and 200x0 mesh coal in water. A fourth slurry consisted of a mixture of the 6x10 and 200x0 mesh coal. Brookfield and Stormer rotational viscometers were used to obtain or simulate rheograms for a range of fine coal concentrations, temperatures, and particle sizes. All the slurries were pumped through a 1-inch diameter acrylic pipe. The fine coal slurries were found to encompass four distinct rheological models. The narrow size distribution of the coal slurries was apparently responsible for the high pipewall friction losses, more so than the particle size. A scale-up method applicable to Bingham plastics was found satisfactory for predicting pipeline headlosses of fine coal slurries from rheology data.

Jan 1, 1974

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By P. M. Daling

This report, sponsored by the U.S. Bureau of mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mire operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be Immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining Industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result In reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966

These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar in September 1981 for the purpose of disseminating recent advances in mining technology in the area of premining research. The introduction and descriptive papers discuss techniques and instrumentation used in premining research for metal and nonmetal mining and shaft design and borehole control for premine planning.

Jan 1, 1982

The U.S. Bureau of Mines conducted a series of laboratory tests in a full-scale model to determine the respirable quartz dust capture efficiency of an irrigated-filter collection system while testing different filter densities, different filter materials, preconditioning water sprays, and wetting additives in the spray water. Impactor samplers were operated upstream and downstream of the filter unit to determine overall dust collection efficiency. The impactor filters containing the 0.7-to 4.7-J.l-m size fractions were analyzed for quartz content, and these data were used to calculate quartz dust collection efficiency. The results of this testing indicated that (1) increased ftIter density improved quartz dust collection, but also resulted in a significant increase in pressure drop across the filter, (2) an alternate synthetic filter material improved dust collection without increasing pressure drop, (3) preconditioning sprays mounted in the system ductwork can have a beneficial effect on dust collection, and (4) additives to the spray water did not significantly increase dust collection.

Jan 1, 1990

By J. W. Town

Recrystallization studies on chrome-bearing spinel materials were made by the Bureau of Mines to determine the effects of certain fluxing agents and cooling rates on the chromium-to-iron ratio of recrystallized spinel. Statistically designed and evaluated tests showed that the ratio of chromium to iron in naturally occurring chrome spinel could be increased from 1.5 to 1 to over 7 to 1 and that the ratio of chromium to iron in the chrome-spinel in a stain-less steel slag could be raised to over 18 to 1. Silica, magnesia, and lime had significant positive effects, while alumina had a significant negative effect. Cooling rates of 200 C per hour in a programmed spiral globar electric furnace were satisfactory for growing crystals of recoverable size.

Jan 1, 1967

By L. A. Neumeier

A refinement of the tungsten-cobalt phase diagram is presented for compositions to 85 at. pct cobalt and for temperatures to the solidus. Preparation of alloys by powder metallurgy methods is described, and the results of studies made by a combination of techniques involving microscopy, X-ray diffraction, thermal analysis, and dilatometry are discussed. The existence of u-W6Co7 is confirmed (rhombohedral D85 structure). The W6Co7 phase forms periectically at 1,685'115° C by reaction of liquid with primary W; the peritectic melt is at 71 at. pct cobalt. The homogeneity range of u-W6Co7 extends to both sides of the ideal stoichiometric ratio, through a compositional range of about 5 at. pct. The compositional limits for u-W6Co7 vary slightly below 1,471°±5° C, the temperature of the eutectic reaction forming u-W6Co7 plus a. The eutectic composition is at 79 at, pct cobalt. The existence of WCo3 is confirmed (hexagonal D019 structure). WCo3 forms peritectoidally at 1,093°±5° C by reaction between a and u-W6Co7 and exists over a narrow homogeneity range of 0.5 to 0.6 at. pct. The solid solubility of cobalt in tungsten is low (maximum 0,9 at, pct cobalt) and results in contraction of the tungsten lattice. Tungsten is extensively soluble in a-Co at higher temperatures; the a-Co lattice is expanded by the presence of tungsten in solid solution. There was no indication of the formation of a o-phase nor of any intermediate phases other than WeCo7 and WCo3. The WeCo7 and WCo3 phases are compared with similar phases in other systems.

Jan 1, 1967

By Russell J. Miller

A high-pressure intensifier system was designed, constructed and field tested as part of a program to determining the feasibility of applying high-pressure water jets on conventional mechanical rock excavation equipment to increase advance rates. Also developed were a high-volume swivel, capable of transferring the high-pressure water to a rotating cutterhead and manifold system for locating and protecting the jets on the cutterhead. Field tests were conducted in a granite quarry near Skykomish, WA, approximately 90 miles east of Seattle. The concept of improving excavation rates by using water jets to assist mechanical cutting was proven to be successful, with an average increase in excavation mete of 50 to 60%. For some tests, the excavation rate was more than doubled. Machine torque requirements were reduced approximately 25% when the water jets were used. It was suggested this was due to reduced cutterhead friction in the presence of the water jets. A comprehensive economic analysis was undertaken as part of a concurrent study to determine the degree of cost benefits attainable from increased advance rates. Very significant savings were seen to be possible. It was concluded that the basic concept of combining a water jet capability with a mechanical excavating machine is definitely possible.

Jan 1, 1976

By L. A. Morely

The overall objective of the subject contract was to investigate the application, economic, and safety considerations of electrical-shock prevention techniques applied to surface and underground mines. Volume I of the four-volume final report starts by summarizing all research performed, and synopses of the three other report volumes are included. The balance of this volume concerns one major task of the contract, the protection of maintenance personnel. After specifying the scope of work for the task, electrical is defined, and needed ground-fault relay characteristics to prevent ventricular fibrillation are established. This is followed by an analysis of alternating-current systems, a comparison of these systems with respect to body currents, and the advantages and disadvantages of the various ground-fault protection techniques. An analysis of direct-current systems for off-track vehicles is then covered. These analyses form the basis for the research recommendations which along with suggestions for future research, conclude the report volume.

Jan 1, 1982

In attempting the predict coal cleat orientation in the subsurface for effective methane degasification of the coal beds in the Warrior coal field of Alabama, approximately 150 rock joint orientations and 45 coal cleat orientations were measured in each of 37 7 ½ minute quadrangles in Tuscaloosa, Walker, Jefferson, Fayette, Winston, Blount, and Bibb Counties. Data from these surface locations, and coal cleat data from eight underground mines was corrected for magnetic declination and titled beds rotated to the horizontal where necessary and plotted on rose diagrams for comparative analysis. Data collected on each joint and cleat consisted of attitude, quality, type, spacing, persistence, lithology, bedding thickness, surface texture, and filling. File data and published and unpublished reports from the State Survey and the State Mine Inspector's Office were re-viewed. Twenty-seven mining companies, most of which supplied information pertinant to the project were also contacted. The information obtained consisted of crop line information structure, and underground mine outlines, all of which were put on 7 ½ -minute topographic quadrangles. LANDSAT-1 imagery and Skylab photography were compared to dominant joint and cleat trends in the study area. Detailed results can be found in an open-file report entitled "Fracture Analyses in a Selected Area of the Warrior Coal Field, Alabama." A master's thesis entitled "The Relationship Between Surface Joints and Subsurface Structure in a Selected Area of the Warrior Coal Field" is being prepared to illustrate the relation-ship of the fracture system to the structure in the Warrior coal field. A proposal has been submitted for research on a project entitled "Rock Fracture Systems and Their Affects on the Extraction of Fossil Fuels in the Warrior Basin, Alabama"

Jan 1, 1976

By T. G. Mayhew, A. A. Bergeron, R. J. Mahany

This report describes an operational communications system which provides remote intra-terrestrial wireless transmission of environmental information. Design and modification specifications of requisite equipment are included along with a detailed description of system operation

Jan 9, 1976

By Franklin D. Cooper

This Bureau of Mines report reviews in detail the foundry coke situation in the United States in 1975. It discusses intrinsic production problems and identifies opportunities for modifying operating practices so that the quality and yield of foundry coke can be enhanced without unnecessary investment in new equipment. Major topics include operating data and attendant practices and problems, the relationship of carbonization phenomena to coke quality and yield, environ- mental impacts of foundry coke plant operations, suggested research and development opportunities, and data on components of oven charges and on foundry coke production and shipments.

Jan 1, 1977

By Francis E. Federspiel

In 1984 and 1985, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 87,720-acre South Boise Yuba study area (formerly known as RARE II Wilderness Recommended area I-4553) to evaluate mineral resources. The study area and additions are in Blaine, Camas, and Elmore Counties, 10, about 60 mi east of Boise. Granitic rocks of the Cretaceous age Idaho Batholith occupy the western two-thirds of the study area. A Tertiary age granitic complex has intruded, and broken into small blocks, Paleozoic age sedimentary rocks in the eastern third of the study area. Tertiary Challis Volcanics overlie both of these rock types. Principal mineralized structures are gold-and silver-bearing quartz veins and shear zones trending northwest to easterly in the Cretaceous granitic rocks. Copper, lead, and zinc are accessory metals in many mineralized structures.

Jan 1, 1987

By H. H. Schrenk, Carlton E. Brown

"The purpose of this paper are (1) to present a broad picture of the recognized methods of measuring the various forms of atmospheric pollution; (2) to evaluate the significance of such measurements; and (3) to suggest suitable methods for obtaining comparative information on the concentration of contaminants in city air.The atmosphere (the gaseous envelope surrounding the earth) consists of a mixture of gases. These gases and their usual proportions are:4/The volume of water vapor in the atmosphere ranges from almost zero (in very cold weather) to about 5 percent arid averages about 1.2 percent.Strictly speaking, any other substance in the atmosphere or an excess of any of the substances mentioned (with the possible exception of water) is a contaminant. Needless to say, there are many contaminants in the atmosphere.In accordance with their physical state, contaminants may be classified as gaseous or particulate, and the latter may be classified as solid or liquid matter. Particulate matter, especially when dispersed in some medium such as air or some other gas, sometimes is referred to as dispersoid, and the complete system of gas and dispersoid is referred to as aerosol.All substances on the earth are potential sources of atmospheric contaminants. Combustible materials (particularly fuel for heating and power), sea water, earth or soil, metals, and animals (including man) are some of the important sources of contaminants.Ordinarily gases are produced by chemical processes, whereas dispersoids are produced by both chemical and physical processes. There are two general dispersoid-producing processes: (1) Condensation, in which molecules join to form larger units or particles, and (2) disintegration, in which large units are reduced to the particulate range (which for the purpose of this article may be considered to be from 100 microns, or 1/254 inch, down to molecular size) by such processes as crushing, grinding, abrading, and atomizing.“Condensoid"" is a convenient term for dispersoids formed by condensation, and ""disintegrasoid"" for those formed by disintegration. Solid condensoids are sometimes called ""fume,"" solid disintegrasoids ""dust,"" liquid condensoids ""fog,"" and liquid disintegrasoids ""mist.""5/"

May 1, 1942

The safety analysis of shaft-sinking operations included a review of accident reports from coal and metal-nonmetallic mine shaft-sinking projects in the United States, a review of foreign and domestic shaft laws, and discussions with shaft contractors and Federal mine inspectors. Accident data were studied to identify the most common and the most severe types of shaft accidents and to determine their immediate and contributing causes. Additional factors such as worker training and experience, equipment and sinking procedures, regulations and enforcement practices were also investigated to determine their impact on shaft safety. The results of the study are summarized in recommendations for improved training of shaft miners and clarification of Federal shaft-sinking regulations. A guide to assist mine inspectors in examining shaft-sinking projects is also included.

Jan 1, 1977

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half being metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceeds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1976