Search Documents

By G. D. Andria

Contract J0275007 was to consist of a thorough two-phase statistical analysis of respirable coal mine dust data from USBM Contracts H0232061, H0232060, H0230029, H0230031, H0210050, and H0242013. Consequently, BCR cataloged and assembled relevant data items from these contracts and formulated procedures suitable for the evaluation. The selected procedure was a Multilinear Regression Analysis which related dust concentrations measured in the mine to other mine parameters. Under the first phase, a thorough analysis of the date from USBM Contract No. H0230029 was completed. Primary results from this analysis are as follows: (1) The five variables that significantly affect dust concentrations in the return behind the brattice are the spray system utilized; the distance from the face to the return brattice; the return airflow; the production rate; and the water consumption rate, in that order. These five variables describe about 85 percent of the total variation in the return dust concentration. (2) Results at the miner and jack-setter locations were somewhat less conclusive due to the fact that only 17 percent of the variation in dust at the miner could be resolved and only 48 percent of the variation at the jack-setter location could be explained. The decision of the sponsor was that these initial results revealed as much information as could be expected; thus, per instructions from the USBM, the second phase (analysis of the other five contracts) was abandoned.

Jan 1, 1978

By W. W. Adams

Because of insufficient funds for printing, the Bureau of Mines was unable to publish its annual bulletin covering accidents at metal mines in the United States for the year 1933. A brief mimeographed summary of the principal statistical data for that year was released to the public late in 1934. Since then reports for 1934 have been received from the mining companies, and in order to avoid further delay in releasing this information to the mining industry and others interested in the prevention of accidents in mining, statistics for both years are presented in this publication with a minimum of interpretation and comment. The fatal-accident rate for the metal and nonmetallic mines (excluding coal mines) of the United States was more favorable in 1933 than in any previous year since 1911, the first year for which the Bureau of Mines obtained reports from the operators. Further progress was made in 1934, when the fatality rate was even lower than that of 1933. On the other hand, the nonfatal-accident rate, which had reached its lowest level in 1932, increased in 1933 and increased further in 1934, although not to such an extent as to prevent the rate for either of those 2 years from being better than that for any year previous to r1931.

Jan 1, 1936

By Dong G. Chae

A model for the leaching of oxide ores is developed and II correlated with laboratory tests for percolation leaching of copper oxide are. Using the model, recovery of metal values and lixiviant concentration of the effluent solution at any time may be evaluated. For the copper oxide ore a simplified version of the model is examined for the leaching mechanism consisting of: 1) a surface flush reaction with the highest rate of lixiviant consumption; 2) penetration of lixiviant to react with copper minerals and gangue constituents; and, 3) slow lixiviant consumption, mostly by residual gangue materials. The simplified model is able to explain reasonably the leaching behavior of copper oxide ore by introducing a concept of effective initial size to correct for packing in a bed of fine particles.

Jan 1, 1979

By R. A. Vik

The influence of thermal treatments on the grindability of low-grade hematitic iron ores from Michigan and Minnesota was examined in bench-scale tests. Treatment factors were roasting temperature, roasting atmosphere, and ore cooling conditions. Bond ball mill grindability and work indices were used as response indicators in evaluating the condition of the ore. Of the three treatment factors evaluated, roasting atmosphere, which brought about the con version of iron oxides to magnetite, had the most significant effect; roasting temperature had the next most important effect; and cooling condition had the least effect. Optimum grindability was obtained with reduced-quenched products of both ores at 650° C, near the alpha-beta phase transformation of quartz.

Jan 1, 1971

This report, the third in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more, effectively extract and process minerals and fuels. Environmental considerations, reduced ore grades, and the related increased quantities of material handled were the dominent concerns of the minerals industry in 1972. Productivity increased in most mineral commodities as equipment became more mobile, versatile, and sophisticated. Increasingly, equipment designs incorporated health and safety features. There was considerable interest in the field of energy and in pollution-free metallurgy processes.

Jan 1, 1973

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By Ivan F. Avery

DOMEST1C production of carbon black in 1963, remained at about the same level as in 1962. Carbon black produced by the furnace process increased 2 percent to 1,880 million pounds in 1963 and accounted for 91 percent of the total output. Channel black production continued to decline and was 14 percent less than a year ago. Shipments during 1963 totaled 2,098 million pounds, a 1 percent increase for the year. An increase of 88 million pounds in domestic sales was partially offset by a decrease of 72 million pounds in carbon black exports. Total value of carbon black production in 1963 was $148 million. The average value per pound was 7.18 cents or 0.12 cent per pound more than in 1962.

Jan 1, 1964

By R. V. Ramani

This volume, the first of a six volume final report, provides an executive summary of the research and results carried out under a grant from the U. S. Bureau of Mines on underground coal mine ventilation. Under the project, a mine ventilation simulator was developed. Sensitivity of leakage and friction factors on the total quantity and pressure requirements was studied. The simulator was applied to a new mine under development, and to an operating mine, to demonstrate the usefulness of the simulator in ventilation planning and in evaluating proposed changes to existing ventilation system. The titles of the other volumes are as follows: Volume II: Mine Ventilation Network Theory Volume III: User's Manual for PSU/MVS Volume IV: Sensitivity of Leakage and Friction Factors Volume V: Application of PSU/MVS to Ventilation Planning of a New Mine Volume VI: Application of PSU/MVS to the Analysis of Modifications to Existing Ventilation Systems

Jan 1, 1977

By R. Newman

An inexpensive slow-speed data acquisition system has been adapted to digitally record multiple parameters simultaneously at intervals of 15 seconds. The system was built for use with standard soils testing equipment to automatically record load and displacement parameters at predetermined instants in time. Simultaneous readout is achieved by the use of special signal conditioner and sample-and-hold circuits which read the multiple signals simultaneously and hold them until the slow acting system can print out. Three channels of a 10-channel system have been converted and found to operate successfully during a series of direct shear tests. A unique feature of the system, which significantly reduced its cost, is the power supply units. Dummy circuits are used to maintain a constant power demand during sampling) thus eliminating the need for a costly power supply with rapid response characteristics. The entire system, having an overall accuracy of 0.25 percent, was put in operation for a cost under $2,500.

Jan 1, 1970

By Joseph L. Ritchey

The Trail Lake RARE II area comprises 1,300 acres (526 ha) in Lassen and Plumas Counties, California, adjacent to the Caribou wilderness. No mining claims, prospects, or quarries are reported within the study areas, and no evidence of potential mineral deposits was found during a field reconnaissance. Quaternary basaltic lava flows uniformly underlie the area. INTRODUCTION The Trail Lake (No. B5-095) RARE II further planning area occupies 1,300 acres (526 ha) adjacent to the Caribou Wilderness in Lassen and Plumas Counties, California. Susanville is about 30 mi (50 km) east and Chester is about 17 mi (27 km) south of the study area. Access from State Highways 44 and 36 is provided by well-maintained gravel roads.

Jan 1, 1981

By Marcel Vanpee

Eight extinguishing powders KCI, were tested on five types of diffusion flames. The effect of flame temperature on the inhibition efficiency was investigated by varying the oxygen index of the flame supporting atmosphere. Inn addition a spectrographic investigation of powder flame dissociation products was carried out on the methane/air/ABC (NH4H2PO4) flame. Dissociation products for this flame included P0, PH, NH, and Na. It is concluded that the main factor to be considered in the efficiency of tie powder is the flame temperature Purple K (KHC03) was typically inefficient in low temperature flames and very efficient in high temperature flames. On the other hand, ABC (NH4H2PO4) was found to lose its efficiency at high temperature but to be quite efficient in the low temperature flames. The effect of temperature is offered as an explanation of the poor efficiency of Purple K (KHC03), against coal dust explosions as contrasted to the high efficiency of phosphate salts against coal dust explosions.

Jan 1, 1982

By W. H. Young

MOST OF THE key items in the bituminous-coal and Lignite industry declined in 1954 compared with 1953. Production, consumption, exports, average value per ton, men working, and days worked all declined; however, in the field of mechanization, the percentages mechanically loaded, mechanically cleaned, mined by auger, and mined by stripping all increased, as did production per men per day. Production.-The output of soft coal in 1954-391.7 million tons- was 14 percent less than the 457.3 million tons produced in 1953. The lower production in 1954 was due largely to a sharp reduction in consumption in the United States and to a drop in exports.

Jan 1, 1958

By Eric E. Cather

A mineral survey of the Fisher Gulch RARE II area (A5299), Trinity County, California was conducted by the U.S. Bureau of Mines and U.S. Geological Survey. The Bureau of Mines was responsible for detailed examination of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. The area is underlain by the Salmon Hornblende Schist. Tonalite stocks 1.5 mi (2.8 km) to the east and northeast of the area intrude the schist and are closely associated with the nearby nines (Cox, 1967). The mines have quartz veins containing sulfides and gold in shears trending east to north past in the schist and tonalite (Hotz, 1972). Strewn and terrace gravel s occupy most of the drainages, many have yielded substantial quantities of gold.

Jan 1, 1981

By Merle L. Bowser

An alinement (steering) sensor for continuous mining machines has been developed under a Bureau of Mines contract. A laser source in the entry projects a beam parallel to the centerline of the entry. The beam is optically shaped to a narrow, vertical fan and illuminates an array of optical sensors bunted on the mini machine. These sensors interpret the location of the beam into meter readings of heading (angle) error and lateral displacement errors. The system, which was tested for 5 months in an operating mine, appears to be fundamentally sound, and with some modification, should be applicable to remote or automatic guidance of continuous miners and other machines.

Jan 1, 1976

By Robert G. Lundquist

The Bureau of Mines compared longitudinal strain energy output of a percussive drill to energy determined by measuring maximum piston velocity. Strain gages were used to determine the strain-time waveform and its amplitude at seven levels of operating pressure and eight levels of thrust. The longitudinal strain energy was found to be approximately 14 ft lb less than the maximum piston energy at comparable operating conditions.

Jan 1, 1969

By Bryan R. Carmenati

This report documents the need for formal health and safety, and equipment operations training in the mine construction industry. The outlines, objectives, and training texts were developed based on the recommendation of needs of mine construction personnel, and those of Dames and Moore (Safety Analysis of Shaft Sinking operations, 1977) and Kinton, Inc. (A Training Program for Conventional and Raise Drill Construction Personnel; Phase I, 1979). The training material samples contained herein (and under separate cover in its entirety) are designed to improve the safety and production of those in mine construction. An instructor-directed presentation is recommended. The results of the study are presented in the Findings and Recommendations section of this report.

Jan 1, 1982

By T. A. Lang

The objective was to develop a Program Plan of analytical studies and tests for determining (1) the optimum installation tension of a coal mine roof bolt, (2) the most valid bolt support theory or theories, and (3) the most valid roof failure theory or theories. On this basis a comprehensive literature search was made and significant material dealing with coal mine roof behavior, roof bolting and roof support was collected, reviewed, classified and analyzed. Emphasis was given to the influence of rock reinforcement on the control of deformation, stress field modification and mine roof stability. An assessment was made of the effect of various parameters including bolt tension, bolt pattern and time of installation, on the effectiveness of rock reinforcement systems, and equations developed for bolt tension as a function of these parameters, and rock properties. From these studies, a major program plan of tests and studies was developed for verifying and validating the most tenable theories of roof behavior and roof support and for determining optimum bolt installation tension.

Jan 1, 1979

By Donald O. Capstick

A mineral survey of the approximately 144,000-acre Borah Peak study area was conducted by the U.S. Bureau of Mines in 1985 at the request of the U.S. Forest Service. The area studied included the Borah Peak RARE II roadless areas (No. 14210, 119,864 acres of land recommended for wilderness designation; and No. X4210, 18,440 acres of land recommended as non-wilderness) and other contiguous Forest Service administered land. The study area is in Challis National Forest in southeast Idaho about 30 miles south-southeast of Challis, ID. Burnt Creek, a conterminous study area to the northeast, on lands administered by the U.S. Bureau of Land Managment, was examined concurrently. Dolomite and limestone inferred reserve bases exceed 1 billion tons each within the Borah Peak study area. The material is widespread and of high quality. Extensive sampling and more detailed mapping are required to better define the resources; however, ample dolomite and limestone occur nearby, outside the study area. Dolomite is the main constituent of several geologic formations within the study area. Sample analyses indicate that the more than 1,000-ft-thick Jefferson Formation dolomite is the most pure and is equivalent to material being mined at a dolomite-to-magnesium processing plant near Addy, WA. Analyses from limestone-bearing formations underlying much of the study area indicate that large quantities of the limestone may be suitable for a variety of uses.

Jan 1, 1987

By W. H. Young

THE DOMEST[C bituminous coal and lignite industry remained fairly steady in 1959 compared with 1958. Although mechanization continued to expand and production increased slightly, consumption, average value, exports, and employment decreased. The percentage of underground production mechanically loaded, the percentage of total production mined by stripping, and tonnage per man per day were at their highest levels. Production.-The output of bituminous coal and lignite in 1959-412 million tons-was 0.4 percent greater than the 410.4 million tons produced in 1958. Production was retarded in 1959, largely owing to the steel strike and reduced exports.

Jan 1, 1960

By Jose P. T. Agapito

Several underground coal mines currently operating in the Beckley District of West Virginia are experiencing serious roof and floor problems. A significant portion of the estimated two billion tons of coal resources may be lost as a result of these ground control problems. Preliminary studies by the Bureau of Mines indicated that these problems are due in part to a high horizontal stress field. During this contract study, a field program was conducted to quantify the horizontal in situ stress. A total of 14 overcoring sites (using the Bureau of Mines strain-relief overcoring technique) in five mines were drilled producing 53 data sets. Analysis of the data was done to provide in situ horizontal stresses for each of the five mine, and for the district as a whole. Stress data indicate horizontal stresses far in excess of that predicted by theory and in some cases, up to six times the estimated vertical stress. In addition to the field testing, a detailed computer modeling study was conducted using finite element and boundary integral (displacement discontinuity) methods. Verification of in situ stresses was obtained by the models and analysis of various development geometries, mining methods and remedial techniques were conducted. Recommendations for reducing ground control problems and future studies are presented.

Jan 1, 1980