Search Documents

By Ronald D. Hill, Elmore C. Grim

The removal of overburden often exposes pyritic materials (iron disulfide). As shown in equations 1 and 2, the oxidation of this material results in the production of ferrous iron and sulfuric acid. The reaction then proceeds to form ferric hydroxide and more acid, as shown in equations 2 and 4. [ ] Consequently a low pH water is produced (pH 2-4.5). At these pH levels, the heavy metals such as iron, manganese, copper, and zinc are more soluble and enter into the solution to further pollute the water. Water of this type supports only limited water flora, such as acid-tolerant molds and algae; it will not support fish life, destroys and corrodes metal piers, culverts, barges, etc., increases the cost of water treatment for power plants and municipal water supplies, and leaves the water unacceptable for recreational uses. The amount, and rate of acid formation, and the quality of water discharged are a function of the amount and type of pyrite in the overburden and coal, time of exposure, characteristics of the overburden, and amount of available water(l). Crystalline forms of pyritic material are less subject to weathering and oxidation than amorphic forms. Since oxidation by oxygen is the primary reaction during early acid formation, the less time pyritic material is exposed to air, the less acid is formed. Thus, a positive preventative method is to cover pyritic materials as soon as possible with earth, which serves as an oxygen barrier. In terms of mining, this step is accomplished by current reclamation techniques and small open pits.

Jan 1, 1974

Reduce rockfall fatalities and injuries by using innovative blasting practices to reduce damage to the rock at the excavation limits with little or no increase in cost. The Problem Falls of highwall have been a leading cause of fatalities, injuries, and equipment damage in the surface mining industry. Although the number of highwall falls is not great, when such an incident does occur it is about 14 times more likely to be fatal or result in severe injury and damage to equipment than other types of surface mine accidents. Overbreak or damage to the rock from poor or improper blasting practices is a major factor contributing to rock falls. Presplitting or cushion blasting is the technique most often recommended for improved wall control. This type of blasting however, adds to drilling and blasting costs and is not universally accepted by the industry. Air gap presplitting techniques, also called air decks, are currently being used in some mines as a less costly alternative to conventional presplitting. Approach Blasting can cause highwall damage, but proper blasting techniques have been shown to reduce the magnitude of rockfall problems. In preventing rock falls, it is important to maintain the natural strength of the rock structure to the greatest extent possible. Improved blasting practices have three main advantages: 1) they are preventive rather than corrective in nature; 2) they are cost effective; and 3) they have a very low impact on the mining operation when properly implemented. New ways of evaluating highwall integrity, such as seismic refraction tomography, were investigated.

Jan 1, 1991

By Lloyd A. Morley

A guide to the development and use of an APL computer program for the analysis of load-flow problems is presented. The program is designed to provide an interactive method of load-flow study to improve underground coal mine electrical system design and safety. The theoretical basis for load-flow analysis is discussed, along with per-unit calculations which facilitate computation. Specific input/output, execution and network modification procedures are presented for using the APL program. In addition, typical results are given for examples taken from power system analysis literature.

Jan 1, 1977

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 9, 1984

By E. C. Lane

The motor gasoline that is bring marketed in the United States this stunner is slightly more volatile than that sold a year ago. During the past eight years the Bureau of Mines has made semi-annual surveys of the gaoline marketed in the United States, the survey just completed being the sixteenth in the series. The cities in which samples have been collected have been chosen as representative of the more important marketing territories as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1927

By John Millhiser, Margaret Bonarek, Dennis McLaughlin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine's Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested and demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

By Thomas R. Bur

The amplitude of the first peak of an ultrasonic pulse which has traversed the diameter of a sphere is obtained for many directions in the sphere. This amplitude is relative to an input which is held constant for all measurements on a given sphere. Since the boundary conditions, distance of travel, and the controllable experimental factors are constant for all measurements, variations in this amplitude reflect variations in the attenuation or absorption with direction. The data are plotted and contoured as an equal area projection. The attenuation symmetry is the symmetry expressed by the contour pattern. Analysis of the data from several rock types indicates that the amplitude expresses a higher percentage of anisotropy than the velocity. In most cases the attenuation symmetry appears to be of the same system as the elastic symmetry expressed by the velocity. Results are shown for three rock spheres.

Jan 1, 1969

Develop a metal substitute which is more plentiful and less expensive than the metals currently being used in high performance, permanent magnets, while maintaining the quality of the magnet. The New Alloy The rare-earth metal used in most high performance magnets is samarium, an expensive metal of limited availability. Cobalt is also used in high performance magnets, but supplies of this metal also are limited because it is not domestically mined and must be imported. The Bureau of Mines embarked on research to find a less costly domestic: metal source for use in industrial magnets. The alloy found most promising consists of mischmetal, a relatively abundant, naturally occurring mixture of rare-earths, which can be used as a replacement for samarium. Additives of copper, magnesium and iron used in combination with mischmetal aid in replacing some of the cobalt needed for the magnets.

Jan 1, 1983

By Robert L. Chufo, H. Kenneth Sacks

Medium-frequency (MF) waves can propagate in a coal seam, bounded above and below by conducting rock, in an approximate transverse electro-magnetic (TEM) transmission-line mode with the electric field vertical and the magnetic field horizontal. The theory of this coal seam mode is applied to recent MF data for a number of mines in order to classify the propagation characteristic of the mines in a simple way. When conductors such as rails, trolleylines, or power cables are present in the vicinity of the measurement path, it is found that the magnetic field versus range plots have two distinct regions with very different slopes. This effect is attributed to coupling of the cylindrically spreading coal seam mode to a low-attenuation conductor guided mode. As a result, voice communications range between mobile transmitters can extend several thousand meters. The use of MF for mine communications is discussed.

By Philip A. Holland

The Bureau of Mines has developed a method for determining helium in water for use in sampling and analyzing surface and subsurface waters for geochemical survey work. The accuracy of the analytical method is within ±10 percent for samples containing above 20 x 10-8 cm3 He (STP)/cm3 H20. The minimum detectable helium-in-water concentration is calculated to be 2 x 10-8 cm3 He (STP)/cm3 water. Water samples are collected in 500-cm3 stainless steel cylinders. The dissolved gases are extracted into a cylinder of equal volume containing a known quantity of neon. The resulting gas mixture is subsequently analyzed for helium and neon-21 by mass spectrometry. The volume of helium in the sample is calculated from the mass spectrometric determination of the helium-to-neon-21 ratio, the known quantity of neon used, and the extraction efficiency of helium.

Jan 1, 1981

By Ted C. Briggs

The Bureau of Mines is evaluating the thermodynamic properties of helium and helium-containing mixtures. Twenty-two compressibility runs were made with helium at 0° C and pressures to 800 atmospheres using a Burnett-type apparatus. Data from the 22 runs were treated simultaneously and as separate runs while different functional forms and weighting factors were used. A fourth-degree-polynomial equation in the pressure gives a statistically satisfactory representation of the compressibility factor when the data are treated simultaneously and a weighting factor of Pr-3/4 is used. The second virial coefficient of helium at 0° C from this investigation is 11.997±0.015 cm3 mole-1. The stated uncertainty is the random error standard deviation. Compressibility factors determined by this investigation are precise to better than 0.01 percent and are believed to be accurate to better than 0.02 percent.

Jan 1, 1969

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United States and publishes economic data on the industry, based upon reports from producers. This publication lists all producers that reported commercial production to the Bureau for 1959. The companies named herein represent virtually all commercial producers of peat. A few companies, however, may not have been canvassed or failed to respond, as tine survey is voluntary For producers, arid the industry has many small operations that operate intermittently. No consideration was given to the quantities of peat produced and output of the various companies listed ranged from less than 100 tons to more than 50,000 tons, Peat is included in the Bureau's annual surveys of the mineral industries because, technically, peat is a fuel. Although none is used for fuel in the United States, peat is a potential source of energy and one of our large mineral resources. The domestic peat industry produces peat chiefly for use as a soil amendment. The industry has expanded rapidly during the past decade with active operations increasing from 45 in 1947-49 4/ to 105 in 1959. Output during this period has increased 218 percent, rising from 131,782 net tons to 419,460 net tons.

Jan 1, 1960

By Oliver Bowles

"A Product from Mica Mines.Mica commonly occurs in pegmatites which consist of large crystals of feldspar and quartz, mica constituting but a small proportion of the total rockMuch of the feldspar thus thro n out during the process of mining is pure and of high quality, end the Bureau of Mines has suggested that much of it could be utilized for ceramic purposes. Encouragement is given to such utilization by the fact that several mines now worked for mica were formerly operated for the production of feldspar. ""'here mines are not readily accessible to railroads feldspar utilization might not be feasible, for it is a much lower priced product than mica and cannot therefore bear as heavy transportation expense. '""here mines ire located close to railroads, however, such utilization would tend to reduce the cost of mica mining, and at the same time assist in the solution of the waste disposal problem.The Bureau has recently been informed that some of the feldspar from mica mines near Spruce Pine, N.C., is now being sold and shipped away. An extension of this by-product industry is to be recommended.A Mica Deposit in New York City.The Bureau recently received a mica specimen obtained from a. building excavation at 157th St. and Riverside Drive, New York City. The specimen was about 2 by 4 inches in size, and fairly clear though containing numerous hair cracks. It was obtained only 7 or 8 feet below street level. At greater depth and with more careful methods of excavation material of much better quality might be obtained. The material submitted could be used for mica washers but not for sheet mica. It is stated by an official of a prominent mica company that many such fragments are obtainable in this locality and the possibility of the occurrence of a good mica vein is thereby suggested."

Jun 1, 1920

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C. 7 Emergency Rescue Hoists There is a need, especially in mine development areas, for portable, on-call, man-rated equipment capable of lifting men through several hundred feet. Wire rope climbing equipment as shown in Figure 37 appears particularly suited to this need. It is portable, weighing approximately 100 lbs. , is currently man-rated for numerous above ground applications and can be electric or air powered. Commercial units currently have a lifting capacity of 1000 lbs. , and can be fitted with bosun' s chairs. Lifting speeds are in the 20-30 FPM range and the equipment is not depth limited. In a situation where miners are unable to climb to the top of a shaft this equipment could rapidly be anchored to the top of the shaft and lowered to them by hand. Since the self contained unit is controlled by the person travelling in the shaft he would be able to negotiate shaft obstruction himself. This would not be possible with other forms of easily deployed free-hanging equipment. Typical manufacturers of this type of equipment are Ohio Hoist Mfg, Co, 321 South Beaver St. Lisbon, Ohio 44432 216-424-7283 Sky Climber Inc. 17311 South Main St. Gardena, California 90248 213-321 -6414

Jan 1, 1976

By J. F. Barkley

"Conservation of fuel in boiler-plant practice is one of the major projects of the Bureau of Mines. The large central stations with their corps of trained operators and with refined equipment obtain relatively good efficiency. It is in the many smaller isolated plants that the large fuel wastes are apt to occur. Some operators seem to feel that their responsibility is largely expressed in the phase the phase ""carry the load,"" rather than ""carry the load and carry it efficiently."" Often equipment is not provided to give sufficiently accurate guidance to the operator.In within many such plants, it is interesting to note how frequently the same mistakes occur. The following quite typical example illustrates some of these circumstances and their effort on operation. The boiler plant consisted of two 1000 hp. boilers equipped with multiple retort under-feed stokers. These were horizontal water-tube boilers with horizontal baffling, having a high bridge wall at the back of the stoker. One boilers was used to carry a summer carry a winter load of about 1250 hp. The operators felt that one boiler was not sufficient to carry the winter load. No instruments are available for the operator's use, excepting the steam ores sure gases."

Mar 1, 1925

Develop a user-friendly computer program that permits those interested in mine health and safety to access and analyze on a personal computer (PC) employment, production, and accident data for U.S. coal and metal-nonmetal mines. This software is being designed with a major focus on flexibility and case of use. The Mine Accident Decision Support System (MADSS) will be available for distribution in mid-1994. Currently, the U.S. Bureau of Mines (USBM) is seeking volunteers willing to pilot test a preliminary version of the software and to provide suggestions for its improvement. Background Since 1975, the Mine Safety and Health Administration (MSHA) has compiled large data bases of information about U.S. mines and the reportable accidents, injuries, and illnesses that have occurred in those mines. Employment and production data arc collected on a quarterly basis from each mine and accident information is collected on an incident -by-incident basis. The USBM has compiled estimated costs for each of these accidents using computer models. All of this information is potentially useful to mine health and safety researchers. However, it has been underutilized because it is stored in large mainframe data bases that arc inaccessible to many users and/or are cumbersome and difficult to use.

Jan 1, 1993

By R. C. Gabler

Laboratory tests on a combined nitrogen roast--two-stage leach--electro-winning approach show promise as a possible process for recovering copper, sulfur, iron oxide, and valuable minor metals (gold, silver, and molybdenum) with a minimum impact on the environment. During the nitrogen roast at 800° C, 15 to 20 percent of the sulfur together with a significant fraction of the volatile elements, such as arsenic, bismuth, lead, and zinc, are removed from the chalcopyrite concentrate. The resulting calcine, consisting of 8-chalcopyrite, troilite, and a bornitelike structure, is leached with hydro-chloric acid to remove 70 to 85 percent of the iron. The digenite in the leach residue is dissolved in an oxygen-saturated, spent sulfate electrolyte. Using a graphite 'anode plus sulfur dioxide to reduce interference from ferric iron, copper of 99.99+ purity is electrowon at current efficiencies of 88 to 92 percent and a cell voltage of 0.4 to 0.5 volt. Copper recovery for the overall process is 98 to 99 percent. Sulfur is obtained in the elemental form from the roasting and leaching steps. Iron can be recovered from the hydro-chloric acid leach solution. Gold, silver, and molybdenum are concentrated in the silica residue from the spent electrolyte leach.

Jan 1, 1975

By C. E. Reistle

[In producing crude oils of paraffin base and of mixed base the producer is often confronted with the problem of preventing and removing paraffin that settles out of oil and accumulates in the well. This paraffin consists of heavy waxes with some sand and asphalt, and varies in. consistency from a soft semifluid wax to hard gummy wax. This problem is by no means a new one as troubles have been encountered with it since the earliest days of the industry. However, with the discovery of the panhandle, Texas, field and other large fields in which extensive troubles have been encountered, the problem has assumed added importance. In new fields the most serious trouble with paraffin is in the flowing wells the paraffin accumulates in the casing and tubing of such wells and unless removed will completely plug the well. This condition also develops in wells which are produced by gas lift, and often presents a serious problem when, this method of producing the oil is used. In older fields paraffin is also deposited on the face of the producing sand that on the walls of the hale or within the interstices of the sand near the hole, and this materially affects the amount of oil that can enter the well.]

Jan 1, 1927

By E. J. HOFFMAN, L. A. SCHOLL, J. c. W. FRAZER

The danger from coal dust in mines has been thoroughly demon- strated by experiment, and consequently the study of the inflam- mability of coal dust suspended in air, that is, the readiness with which a cloud of coal dust inflames, is of decided importance to those engaged in coal mining. Much knowledge has been gained from the work done in the large galleries constructed at official and semiofficial stations in this country and abroad, but the study of the coal-dust problem in these galleries requires so much time and is so costly that there is need of a reliable laboratory method for obtaining a classi- fication of the great variety of dusts that occur in mines. The investigation described in this paper was an attempt to devise such a method. It was a preliminary investigation, and work in the same direction is being continued by the Bureau of Mines. As Mr. Frazer has severed his connection with the bureau, it is deemed advisable to publish the results of his study substantially as he prepared them, with little attempt to draw conclusions or to show the bearing of the results on other studies now in progress. The results of these studies and a full discussion of the significance of the laboratory investiga- tions will be published in future reports of the Bureau of Mines. The reader should remember that any laboratory method, since it involves conditions that differ so greatly from those of actual mining, should be thoroughly tested, and the results obtained by it should be confirmed by experiments conducted on a scale simulating mining conditions before final conclusions are drawn. The need of a laboratory method has long been felt, and several investigators have devised apparatus and methods. The work done by Vital, Holtzwart and Von Meyer, Bedson and Widdas, Le Chate- lier, and that of the British Coal Dust Commission is of great interest in this connection. Bureau of Mines Bulletin 20 contains a sum-

Jan 1, 1913

By Chester L. Arnold, Reinhardt Thiessen, Alexander Lowy

"INTRODUCTION Peat is the accumulated mass of plant materials that remain after partial decay under specific conditions. In the swampy peat bogs dead material which falls on the surface immediately is attacked by fungi and aercbic bacteria. Decay under these conditions is rapid, but of relatively short duration, since the constant addition of new material soon forces the older layers below the water level, in this position, without access to oxygen, the plant constituents are attacked mainly by anaerobic bacteria, and decomposition proceeds slowly. The largest part of peat is contributed by the woody tissues of plants, the chief constituents of which are cellulose and lignin, together with a small proportion of hemicelluloses. During the normal process of biological decay celluloses disappear more rapidly than lignin. The result is a complex substance known as humin, from which the humic acids may be extracted.In 1826, Sprengel 5 found that when decayed plant materials were extracted with alinnli and the resulting black liquid acidified with mineral acid a brown gelatinous precipitate was formed. To this product, which was a brown amorphous powder when dry, he gave the name ""humic acid'. Since that time, chemists have used the name rather loosely to designate products which have been isolated by very diverse means from soils, decayed woods, peat, lignite, and coal. An excellent review of the early work on humic acids was published by Baumann 6 in 1909. This publication aroused the interest of Oden, who then investigated the humic acids. An account of Oden’s work, as a good survey of the literature, is contained in his monograph “Die Huminsauren”. 7"

Nov 1, 1934