Search Documents

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

3. Application of Proposed Revised Standards 57.11-50 to Mines Surveyed 3.1 Subparagraph (a) 1 "Each mine shall have at least two separate and properly maintained escapeways from each working place to the surface which are so positioned that physical or environmental damage to one will not lessen the effective¬ness of the other, and which meet the requirements of travelways and man hoisting standards These escape¬ways shall reach to within 1000 feet horizontally or 300 feet vertically of each working place " 3. 1. 1 Discussion This section will deal with the 1000 and 300 feet distance requirements, Section 3. 5 will deal with the "environmental damage" provisions. During the course of the mine surveys, it became obvious that one mine's 1000 foot distance was nowhere near equal to another' s --not in the actual distance but in the time required to traverse that distance. This -Ls true for the 300-foot requirement as well. The most obvious example is that one could traverse down a 300-foot raise much faster than climbing up the same distance. The temptation is strong to recommend that the distance requirement be changed to travel times instead. However, this approach would unfortunately lead to a lot of subjective evaluations. Having a time requirement for an entire mine evacuation (Subparagraph 6) is one thing, time requirements and the requisite inspection proce¬dures for each working place are quite another.

Jan 1, 1976

To prevent injury to miners caused by violent whipping of mining machine trailing cables. Approach: The hydraulic cable controls are adjusted to reduce whip by visual reference of the cable sag to the height of the cable guide. How It Works: The cable sag is adjusted by visually estimating its height above the ground, at a specific reference distance behind the machine. This reference distance is measured horizontally back from the point where the cable leaves the cable guide. The Reference distance is 2H where H equals the height of the cable guide above the floor. See Figure 1. Cable sag should be less during rewinding than during unwinding. During cable unwinding, the cable height (at the refer¬ence distance) should equal 1/31-1. During rewinding, the cable height should equal ½ H. Field tests were made on several manufacturers' equipment after adjusting cable sag as above. Cable whip was greatly reduced for all, and whip was almost eliminated on a shuttle car equipped with a Joy Manufacturing Company 500108-104 cable reef and the newer (nonporous) shuttle valve. The following directions are for adjusting cable sag on a shuttle car equipped with a Joy Manufacturing Company 500108-104 Cable Reel equipped with the newer shuttle valve. Cable sag can be adjusted on machines equipped with other cable reels and valves by referring to the manufacturer's manual and making the appropriate cable valve adjustments.

Jan 1, 1976

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX A - PNEUMATIC TRANSPORT OF FLY ASH 1. Introduction Two types of pneumatic transport of fly ash are critical to the success of (1) Transport of fly ash from the fly ash truck to the entrance to the borehole. Depending on the surface topography, this may be horizontal, decential and ascential. (2) Vertical downflow of fly ash through the borehole. All fly ash trucks have limited pressure with which they can pump the fly ash. Thus, the pressure drop in the fly ash hose will define the maximum length for pumping and consequently the maximum distance that the fly ash truck can be parked from the auxiliary blower. The same relationships describe the flow of the dilute fly ash-air mixture produced by mixing with the auxiliary air from the blower and thus define the selection of the pipe diameter. These are im¬portant considerations in the proper selection of the location of the passages to be sealed and the type of surface preparation required. The flow characteristics of fly ash down the borehole determine the selection of the minimum borehole diameter and the blower pressure. This appendix presents theoretical analyses of these flow regimes and summarizes the limited experimental data obtained during the field tests at Grant Town, described in Section 8.4. The analysis for the borehole flow is presented first as it is of greater interest to the program. This is followed by a discussion of the horizontal flow.

Jan 1, 1973

By I. D. Shah

The copper-nickel ore of the Duluth Gabbro Complex in northeastern Minnesota is a large potential domestic resource of cobalt and platinum-group metals. However, because of the low grade of the primary metal values (0.5 pct Cu, 0.15 pct Ni), the private sector has assigned a relatively low priority to the development of technology for processing this ore, anticipating that mining probably would not begin until the mid-1990's. Furthermore, preliminary processing flowsheets considered by the mining companies centered on the primary metal values. As part of an effort to help provide the basis for technology to recover critical and strategic minerals from domestic resources the Bureau of Mines is investigating methods to recover all of the mineral values, in the Duluth Gabbro material, with particular attention to the byproduct critical minerals. A key step in this process is the removal of a relatively large amount of iron present in the bulk sulfide flotation concentrate to permit subsequent extraction of mineral values. This report describes a direct smelting method that removes most of the iron and produces a copper-nickel-cobalt matte, an intermediate product from which the metal values subsequently are separated. Copper, nickel, and cobalt grade and recovery data are presented for the direct smelting method. Test results showed that under certain conditions some of the mineral values reported to the slag, requiring slag cleaning to recover them.

Jan 1, 1983

To develop a system which will effectively detect and extinguish fires in underground fueling areas while also providing a warning for nearby miners. Approach A system involving optical fire sensors. automatically-released dry chemical and aqueous film-forming fluid (AFFF) fire suppressants, and automatic alarms was designed from off-the-shelf, state-of-the-art components, and was in-mine tested at two mines in the two typical underground fueling area situations: fuel transfer areas and fuel storage areas. How It Works As mines become more mechanized, the number of fire hazards increases since fueling areas are more abundant. Fire hazards are especially serious in deep mines, since escape time is longer. To help solve this growing problem, the Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the National Fire Protection Association (NFPA), has developed and in-mine tested a cost-effective fueling area fire protection system. The system was designed to be rugged enough for reliable, long-term use, yet to utilize state-of-the-art, off-the-shelf components to maintain cost-effectiveness. The system consists of cross-zoned, ultraviolet flame sensors used for quick response to fire, and a dual-agent fire suppression subsystem. A dry chemical is used for fast fire -knockdown," and AFFF (or "light water") is used for long-term, fire-securing capability. The basic components of the system are shown in the schematic illustration.

Jan 1, 1982

Reduce or prevent acid mine drainage from coal refuse piles and surface mines by inhibiting the growth of acid-causing bacteria. Approach A dilute surfactant or deter? gent solution is applied directly to coal refuse piles or overburden using a hydro-seeder or road watering truck. The surfactant treatment can be used either as a preventive measure to avoid a potential acid drainage problem or to reduce water treatment costs by controlling acid drainage at its source. How It Works Acid drainage is prevented or reduced by inhibiting the growth of Thiobacillus ferrooxidans, a type of bacteria which obtains most of the energy it needs to survive by oxidizing ferrous iron in water. The oxidized iron in turn attacks pyrite, which forms an acid and additional ferrous iron for the bacteria to oxidize. T. ferrooxidans is protected by an outer membrane which enables it to survive in its acid environment. Anionic surfactants, or surfactants containing negatively charged ions, can be used to destroy this membrane, thus killing the bacteria and slowing down the oxidation of acid-forming pyrite. Of the anionic surfactants tested to date, sodium lauryl sulfate (SLS) appears to be the most effective as a bactericide. Alpha olefin sulfonate and alkyl benzene sulfonate are acceptable alternatives. These surfactants are major components of common household products, such as laundry detergent, shampoo and toothpaste. They are, therefore, readily available, inexpensive, biodegradable and present no environmental problems at low concentrations.

Jan 1, 1983

By G. T. Brow

An experimental method is described for testing diffusion of gases in crude oils at pressures and temperatures up to 3,000 psia and 200° F. A sampling technique was developed to withdraw by constant-pressure mercury displacement about 60 µl of oil from the diffusion cell through any of several 1/2-in vertically spaced capillary tubes and to trap about 4 µl of the oil in a specially designed microsampler. Oil trapped in the microsampler can be completely inserted in the sample inlet of a chromatograph. From analysis in a three-stage chromatograph (GLC), gas concentration in a sample is determined from the ratio of gas peak heights to area of peaks of reference components (hexanes or heptanes) in the oil. A diffusion coefficient is calculated from measured concentration profiles with known equations for diffusion in finite or semi-infinite systems, depending on whether the gas has or has not reached the end of the oil column. Results are given for a test of methane diffusing at 2,560 psia and 160° F in crude oil from the Weber Sandstone reservoir in the Rangely field, Colorado. A constant diffusion coefficient of 3.34 X 10-5 cm2 per sec was obtained which gives a good fit between calculated and experimental profiles determined at six times after start of diffusion. The maximum standard error of gas concentration determinations experienced with this method was ±0.88 ml per ml of gas-free oil.

Jan 1, 1970

By Michael J. Beus, Stephen Iverson

BACKGROUND A mine shaft is the lifeline to underground mines. Mine operators depend on safe, uninterrupted, and efficient movement of workers and materials. The shaft and hoisting system provides access to the network of openings used to recover the underground resource, provides vertical transport of miners and materials, and serves as an escapeway in case of an emergency. Accidents involving hoisting can be catastrophic. Such was the case in 1973 at the Markham Colliery in Derbyshire, UK when the conveyance overwound and fell to the shaft bottom, resulting in 17 deaths. Hoist and elevator machinery must meet the requirements specified in the Code of Federal Regulations (CFR), Parts 57 and 75. According to the Mine Safety and Health Administration (MSHA) data, many shaft-related accidents in the United States are associated with the hoisting cycle. MSHA statistics show that there were about 1500 shaft- related accidents in the 5-year period between 1992-1996. Most of these accidents resulted from the action, motion, or failure of the hoisting equipment or mechanism and involved movement of the conveyance which includes cages, skips, ore buckets, and elevators. A hoisting hazard may be characterized as an "unsafe hoist operating condition caused by insufficient or inaccurate information available to the hoist operator" (authors' quote). Earlier investigators have defined safety features and operating and maintenance standards for hoists, and reported on monitoring and control systems and sensors for hoists and conveyances [Farley, 1983; Ward, 19931. However, despite the considerable technological progress and hoisting control improvements in recent years, safety- related issues that require further investigation still remain. The hoist operator must constantly be aware of two important hoist-operating conditions: the position of the conveyance and the tension in the hoist rope. If this information is not available or is inaccurate, the hoist becomes unsafe. Current technology provides this information indirectly from sensors and indicators in the hoist room. However, unlike a building elevator hoistway, mine shaft hoistway problems often include: 1. poor ground conditions and excessive shaft wall and guide displacement; 2. rock bursts in deep mines (resulting in large rock movements and fragments blocking the hoist way); 3. water, ice, and salt buildup (impeding the smooth flow of the conveyance); 4. severe vibration from hoisting (resulting in loose guide support brackets, broken welds, or other alignment and conveyance mechanism malfunctions). The second issue relates to dynamic rope loads applied during normal winding, particularly during loading, acceleration, and stopping. Safety factors on wire rope are based on static load. They are artificially high to account for all cases of dynamic loads, even though the total load history on the rope (static and dynamic) during service is unknown. Therefore the tension, and thus the compliance with wire rope load safety factors, is unknown to the hoistman.

By Sean Gallagher, Rhys Llewellyn, Jay Mattos

This paper contains the results of an examination of accident, injury, employment, and production information reported to the U.S. Department of Labor's Mine Safety and Health Administration (MSHA) and provides information on some of the measures longwall mine operators are using to prevent accidents In all industries, technological advances play a key role in determining those who will survive as competitive participants in an increasingly global marketplace. While mining is among the most basic of industries, technological change is neither unfamiliar nor unwelcome to miners. Historically, technological advances in mining, particularly coal mining, have tracked closely with fluctuations in demand. In the early 1900's, coal accounted for more than three quarters of all the fuel consumed in the U.S. To meet this tremendous demand, underground cuffing machines were introduced, resulting in faster, more efficient coal extraction. Transporting coal to the surface, however, remained labor intensive. In the 1920's, nearly all underground coal was still being hand loaded. Demand for coal then declined as the price of oil, natural gas, and electricity became competitive. In the late 1930's and throughout the duration of World War II, coal demand and production was high. By 1940, more than half the coal mined was being mechanically conveyed to the surface. In 1948, the continuous mining method was introduced in the U.S., further accelerating the extraction process. By the 1950's and 1960's, however, coal production again declined as railroads converted to diesel fuel and gas and oil provided a larger share of the home heating market. Underground coal mines required even more mechanization to remain competitive as an energy source. The first longwall system was introduced in 1960. By 1995, longwalls were producing more than 189 million tons of clean coal annually, surpassing continuous mining production for the second straight year. The mining of coal and other materials has not come without a huge loss of life and considerable human suffering. More than 103,000 workers died from injuries in U.S. mines in the last 85 years. Between two and three thousand miners died each year from the turn of the century until 1931, many from underground fires and explosions. The U.S. has witnessed a tremendous drop in fatalities in underground coal mines. Credit for that is due to safety inspections and enforcement activities, better safety awareness and practices among management and labor, improved ventilation, the use of safer equipment, and increased mechanization which removed many miners from the hazards at the face and also reduced the size of the mining work force. There is little doubt that longwall mining has greatly increased underground coal mine productivity. The degree to which longwall mining has contributed to a safer work environment for underground miners is more difficult to ascertain.

By L. C. IlsLey

"The use of trailing cables on cutting machines, loading machines, and similar electrically operated apparatus is recognized as a necessary adjunct to the economical operation of such units. On the other hand, such cables because of their liability to failure from being run over by cars, locomotives, and other track-operated equipment offer one of the greatest hazards - indeed, probably the worst hazard - met with in the operation and maintenance of permissible equipment. Therefore, the Bureau of Mines is seeking ways of making the use of trailing cables less hazardous.Recently the bureau conducted an extensive investigation of both concentric and duplex rubber-sheathed trailing cables at the Pittsburgh Experiment Station. The results of this investigation were published in two reports.3 4In a larger part of portable motor operations in mines a double-conductor cable can be used. The investigation already mentioned indicated that it is feasible to construct a 2-conductor cable that will stand considerable abuse, such as being run over by loaded cars or light-weight locomotives without producing dangerous arcing in the cable either from grounds or short circuits. There are conditions where more than two conductors are necessary, and in such instances it will probably be necessary to use a cable less resistant to this kind of abuse.Schedule 2C, covering the tests of electric motored equipment, was approved February, 1930. This schedule provides for performance tests on trailing cables as follows;Trailing Cable Performance: The following performance test, optional with the manufacturer, is established for determining the suitability of trailing cables for use on permissible equipment. Trailing cables that pass this test will be especially recommended for this service.The cable will be placed across the two rails of a track and a 4-wheeled 7-ton car will be run over it 50 times. The speed of the car shall be approximately 3-1/2 miles per hour and potential shall be applied to the cable during tests. The cable will be shifted in position after each passage of the car thus giving 100 places over which two wheels have passed. To warrant special recommendation of the Bureau, a cable must neither become short-circuited nor grounded either to the rails or wheels in more than 10 per cent of the 100 places.The Bureau of Mines is prepared to conduct tests as outlined in the foregoing paragraphs to determine the suitability of trailing cables for use on permissible equipment. Application for such tests should be made to the Director, Bureau of Mines, Washington, D. C. Each application should be accompanied by a check for $25.00, made payable to the Treasurer of the United States, to cover the expense of conducting the test on a given size and make of cable."

Apr 1, 1930

By Staff

This Bureau of Mines report is devoted to descriptions of investigations pertaining to underground mine trailing cables, their handling, splicing, and the use of couplers.

Jan 1, 1979

"One of the functions of the United States Bureau of Mines is to investigate the ability of electrical mining equipment to operate in a gassy mine without danger of igniting explosive atmospheres. To accomplish this purpose, tests are made in which mixtures of gas and air are ignited in the equipment while it is surrounded by explosive atmospheres of the same composition. In such tests, records of pressures developed by the internal ex-plosions are obtained and observations are made of any flames, sparks, or smoke which may issue from bearings and joints. Occasionally the explosion pressures in a mining machine rheostat or a compartment of some other machine reach a value which is judged to be excessive or abnormal.A number of factors are known to influence the explosion pressures, and both German and. British investigators have irate extensive research on their effects. Much of this work had been done with artificial compartment which certain conditions could c held, constant while others were being varied. The U. S. Bureau of Mines has not made any research on a scale to compare with that of the British or German investigators; however, special studies have been necessary from time to time to determine the cause and remedy for high pressures obtained in the routine test of some piece of mining machinery. Thus it has been possible to verify some of tee theories established on a purely experimental oasis by practical tests of machines as actually built for mine use.Some of the factors determined the pressure that will result when an explosive mixture in a compartment or connected compartment is ignited are: (1) The volume of explosive mixture ignited, (2) the percentage of as in the mixture, (3) the amount of coal-dust in the compartment or compartments, (4) the degree of movement or turbulence of the mixture at the time of ignition, (6) tightness of the joints and bearings, (6) the size of opening between, compartments, (7) the distance between the point of ignition and openings, and (8) the cooling, effect of surfaces and of material inclosed in the compartments."

Dec 1, 1929

By A. B. Hooker, J. W. Paul

"There was a time when any suggestion that the Davy flame (safety) lamp be discarded, would have evoked unlimited, criticism. However, that time is past.Investigations both here and abroad have shown conclusively that the Davy lamp does not have the necessary factor of safety against ignitions of mine gas, and England, the lost stronghold of the Davy lamp in Europe, has eliminated this lamp and substituted safer types.In the United States there are companies who still use the Davy lamp in spite of all that has been said and published as to the dangers connected with its use.Recently the purchasing agent of an anthracite coal company requested the Department of the Interior, Bureau of Mines, to pass upon the safety of some braise gauzes for use in a shielded Davy lamp. A shielded Davy lamp is an ordinary Davy safety lamp equipped with a circular brass shield that is attached to the lamp posts. This shield extends about one-half way around the gauze and one-half of the gauze height. The main purpose of the shield is to prevent the lamps being extinguished by a sudden increase in the velocity of the air current past the lamp.The brass gauzes submitted for this test represented two grades of brass - a yellow brass and a red brass. The analysis of these brasses was not determined. Two shielded Davy lamps that were submitted for the tests each had a steel gauze. These steel gauzes were also tested. Tests were made in horizontally moving mixtures of Pittsburgh natural gas and air at velocities of 400 to 1,000 feet per minute. The gas percentages used were 7%, 8.6%, and 11%. Tests were made with the lamp shield in two positions relative to the lamp and direction of flow of the gas-and-air mixture. In one position the shield was between the gauze and flow, as normally used. In the other position the shield was on the downstream side of the lamp. The tests were continued until one or more failures or gas explosions been obtained with each of the six gauzes. The results of these tests summarized as follows:"

Jun 1, 1923

By Ludwig Schmidt

[The use of vapor-tight tanks has proved so effective in reducing the evaporation losses of petroleum that today practically all operators are using this typo of equipment. It has boon shown, however, that vapor-tight tanks should be supplemented with additional measures which will further reduce evaporation. Probably the most effective use of the supplemental measures are found on the small producing leases where the breathing losses from vapor-tight stock tanks materially affect the volume and gravity of the stored oil. The breathing loss from a vapor-tight stock tank that is filled and emptied daily is a negligible quantity. Also, the filling loss, which on the average varies between 0.1 and 0.2 per cent, usually is not of a sufficient quantity to affect materially the value of the crude. However, the combined breathing and filling losses from a vapor-tight tank requiring several days to fill are of sufficient importance to warrant the use of measures in addition to the vapor-tight tanks. The breathing losses are caused by atmospheric variations. Probably the greatest are the changes in atmospheric temperature which cause changes in temperature of the vapors in the tank. During the day, as the temperature increases, the gasoline-saturated vapors in the tank expand and are forced out into the atmosphere. At night the vapors are cooled and contract, drawing into the tank fresh air, which becomes saturated with gasoline vapor and is forced out of the tank during the following day. In Addition to the maximum and minimums temperature variations there are many smaller variations throughout a twenty-four period caused by showers, clouds, winds, and other atmospheric conditions which likewise cause the tank to breathe. The two mist common measures used by lease operators for reducing breathing losses in vapor-tight tanks are, first, operating; lease tanks under pressure, and second, the use of light colored paints anti tank houses. In this report these two methods are discussed together with their adaptability to lease operation. Results of experimental observations are given which show the reduction of evaporation looses where these supplemental measures have been used.]

Jan 1, 1927

By David C. Byrne

PURPOSE: Evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. RESEARCH SUMMARY: The results of previous NIOSH research show that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and gender. Using hearing thresholds at 4,000 Hz as an indicator, coal miners experience hearing loss 2.5 to 3 times greater than would be expected for persons not exposed to occupational noise. At age 50, 90% of coal miners and 49% of metal/nonmetal miners were found to have a hearing impairment. In comparison, only 9% of a nonoccupationally exposed control group had a hearing impairment at age 50. There are numerous barriers to the prevention of hearing loss among miners. In an effort to overcome some of these obstacles, this work was initiated to evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. Experiments will involve analysis of this new technology under both laboratory and field conditions. Laboratory components will consist of controlled studies using an anthropometrically correct test fixture as well as human subjects to evaluate the adequacy/effectiveness of various hearing protective devices. Electroacoustical performance testing of new noise monitors will also be conducted in a laboratory setting. Subsequent field studies will determine the actual usefulness and practicality of the personal protective/monitoring equipment as used in different mining situations. It is anticipated that increased on-the-spot awareness of hazardous noise levels and the availability of better-suited hearing protectors will provide a degree of protection beyond what is currently attained in different mining environments. Therefore, the intent of this project is to identify and adapt new acoustical technologies and products that have a direct application to individual mine workers. With increased knowledge of these technological advances, a greater demand for similar devices will likely occur, which, in turn, will lead to a better understanding and awareness of hearing loss prevention methods throughout the mining community. The ultimate goal is for widespread integration of useful hearing loss prevention products and devices into the daily routines of miners

Jan 2, 2000

By Thomas M. Barczak

The safety of mine workers depends on the proper installation of roof supports to prevent the ground from collapsing into the working areas of an underground mine. As new support systems are developed, they need to be properly evaluated to make sure that they are capable of providing adequate roof support before they are first used in a mine. In addition to making certain that the supports meet basic safety criteria, the limitations of the support need to be fully defined in order to avoid improper application of a particular support design. The National Institute for Occupational Safety and Health (NIOSH) operates a world-class facility called the Safety Structures Testing Laboratory. This laboratory contains a unique load frame, the Mine Roof Simulator, which is capable of simulating the ground behavior in underground mines for conducting full-scale evaluations of roof support systems. Safety performance testing protocols using the unique Mine Roof Simulator have been developed for both standing roof support systems and longwall shield supports. The purpose of this paper is to describe these test procedures. The protocol for standing roof supports incorporates seven test series:( 1) uniform loading baseline tests, (2) height evaluations, (3) asymmetric loading, (4) biaxial loading, (5) load rate studies, (6) active loading determination, and (7) static loading evaluations. For longwall shields, a four-series test program that accurately simulates in-service conditions on a longwall face is proposed. This test program consists of (1) transfer of horizontal load to the caving shield-lemniscate assembly (zero-friction test),(2) point loading of shield joints due to lateral movement or rotation of the canopy, (3) evaluation of leg socketand leg cylinder integrity, and (4) face-to-waste racking of the shield. In addition, an evaluation of the shield’s hydraulic components will be conducted prior to the performance testing. These protocols will provide state-of-the-art safety performance evaluations of emerging support technologies, as well as a means to assess the safety of both new and aging longwall shields. Hence, this effort will enhance the safety of mine workers by ensuring that critical support elements are properly designed and that aging supports are retired before their support capability is jeopardized.

Jan 10, 2000

By George H. Ashley

Character The bituminous coals of Pennsylvania range from low volatile to high volatile, but are all low moisture coals The coals are of three types caking of coking, noncaking or splint, and cannel The percentage of volatile matter in all kinds changes from low at the east to high at the west This change is thought to be due to the pies sure and folding to which the coals along with the other rocks have been subjected In the Broad Top field, and in Somerset, Cambric, Clearfield, Centre, and other counties to the northeast, most coals contain from 3 to 5 times as much fixed carbon as volatile matter, the fixed carbon ranging from 67 to 75 per cent, and the volatile mattes from 16 to 24 per cent These coals are classed as lovol coals In the line of counties just west of those listed the coals are of the medium volatile class (midvols) This includes the famous Connellsville coking coal Still farther west, covering most of Washing ton and Westmoreland counties, and the counties to the north of them are high volatile coals of gas coals (hivols) This is discussed in Part I on the geology of the coals of Pennsylvania, where is given in isocaib map Cannel coals ale found in many par is of the bituminous coal field of Pennsylvania, but in particular in Beaver Butler, Armstrong, Indiana, and Clear field counties The cannels of Beaver and Butler. counties are typical high volatile cannels, many of which have been used in times past for oil distillation The cannels of Armstrong and Indiana counties are medium volatile cannels, and while main taming the physical character of cannels, have no more volatile neat ten than the coals around them The cannels of Clearfield County tie low volatile Splint coals of noncakmg coals are not abundant in Pennsylvania. The Sharon coal, formerly mined in Mercer County, was a noncaking or splint or block coal, and was formerly used in the raw state in non smelting Uses STEAM COAL Practically all of the coals of Pennsylvania are steam coals, though many coals in the Commonwealth, because of high ash, are not good steam coals The coal of the Pittsburgh district has long been famous

Jan 1, 1928

By R. E. Head, Virgil Miller

"INTRODUCTIONRecent investigations at the Intermountain Experiment Station of the Bureau of Mines at Salt Lake City indicate that metallurgists have given little attention to the occurrence of jarosite minerals in the oxidized ores of lead and silver. These investigations have also emphasized the importance of knowing when these minerals occur in the oxidized ores, especially those containing lead, silver, and gold, as their presence is a material factor in selecting a suitable kind of treatment. Since the question of the occurrence of jarosites in oxidized ores has come to the attention of the Bureau of Mines, investigation has indicated that plumbojarosite and argentojarosite are quite common. These two minerals appear to be widely distributed and probably escaped recognition by persons who had attempted to treat certain oxidized lead ores in which the jarosite minerals represented a material portion of the metal content.Consideration of the physical characteristics of the jarosites also indicates that in many cases failure to treat some of the oxidized lead ores with success has been directly due to the fact that the greater portion of their lead and silver content was present as plumbojarosite and argentojarosite. The data and the description of these minerals given in the body of this paper indi¬cate that attempts to recover lead and silver from ores in which appreciable amounts of the metals occur as plumbojarosite and argentojaeosite would be unsuccessful if confined to gravity methods of concentration. There are un-doubtedly considerable tonnages of oxidized lead ores in the various mining regions of this and other countries, and it is quite probable that in some of these ores the metal content of lead and silver may be largely anglesite (lead sulphate) and cerussite (lead carbonate) but that they will also contain cerargyrite (silver chloride), argentojarosite, and plumbojarosite. The treatment of such ores therefore presents an important problem, since a product is discarded from ores from which the recoveries of lead and silver have been below 70 per cent which is probably too low-grade to warrant aftertreatment by any process now in use."

Apr 1, 1928

By Edward P. Barrett

[Iron oxides, when reduced at temperatures below 900° form a dark gray substance, very porous bait otherwise in almost the same form as the original particles. In the temperature ire range of 1,000 to 1,100° the product is pertly sintered but still shows the outlines of the original particles. Those products are known as "sponge iron." At temperatures of 1,100 to 1,2000 the metallic iron begins to flow together and to a semifused, pasty, porous mass called a "bloom," which can he worked under a hammer to form a product similar to wrought iron; it contains slag inclusions and is too low in carbon to make steel. If the temperature is 1,300 to 1,300°, part of the iron will fuse enough to absorb more carbon. The dissolved carbon lowers the melting point and still more carbon is absorbed. The melted portion acts a flux for the unmelted metallic particles until the entire mass becomes a high-carbon fluid known as "cast iron." Sponge iron was probably the form in which the first iron was recovered from the ores. As early as the eighth century the Catlan forge3 developed into a low-shaft furnace known as the "high bloomary," in which iron eras produced in the form of a pasty mass. In 1340 the first blast furnace was built in Belgium. The greater part of the iron was made into wrought-iron blooms by crude puddling processes. Charcoal was used as the fuel until tie latter part of the 17th century when coke was used in England. In 1865 Bessemer built his first converter in. England, and within a few years the Siemen's regenerative open-hearth furnace was developed, also in England. Enormous expansion in the metallurgy of iron followed. The idea of "direct processes" for the production of iron arid steel has persisted throughout all this time. The production of steel from sponge iron has theoretical advantages over the present-day standard methods, and handreds of so--called "direct processes" have been proposed or tried during the past century.4]

Jan 1, 1929

By R. S. James, E. J. Gleim

Not long after electrically driven equipment was introduced into coal mines it became apparent that the spark-producing parts, such as controllers and motors, required safeguards to prevent the ignition of mine gas that might come into their vicinity. Many of the early designs attempted to provide protective enclosures having ventila¬tion and relief for pressures if ignition should occur within. The principal feature of the Davy safety lamp, namely, the wire gauze, was employed widely for this purpose. Other devices were developed to reduce the temperature of products of combustion escaping through the protected openings to a value below that which would cause ignition of surrounding explosive atmospheres. Although many such devices performed their intended function satisfactorily under laboratory conditions they were not so satisfac¬tory when subjected to the rigorous conditions encountered under¬ground. Corrosion, mishandling, and accumulations of grease and dirt reduced or destroyed their protective qualities after a period of service in the mines. In the United States this has led to abandon¬ment of special devices in favor of what is called " total enclosure " which means that no regular provision is made for ventilation and release of pressure but rather that the housings or enclosures are built strong enough to withstand the explosion pressures without rupture. As a further protection the joints usually are made of broad, closely fitting surfaces. It is impractical to make such joints absolutely gastight in ordinary machine practice when provision must be made for partial or complete disassembly to facilitate ad¬justments and repairs. Therefore, when an explosion occurs within such enclosures flames may escape through the joints. If the latter are broad enough and not separated too widely, however, the flames will be cooled by contact with the metal surfaces (flanges) of the joints, by rapid expansion, or by both cooling and expansion, with the result that an explosive atmosphere surrounding the enclosure will not be ignited. This is termed " flange protection." In testing parts of cutting machines and other equipment for coal mines, with the ultimate object of approving the equipment for use

Jan 1, 1935