Search Documents

On November 9, the Reynolds Metals Company cut production by 12 at its primary aluminum smelters at Troutdale, Oreg., and Longview, Wash., as a result of an earlier 25% power cutback by the Bonneville Power Administration due to lower than normal stream flow in September, the Aluminum Company of America had closed one potline at its Vancouver smelter because of the power cutback. Nearly 700 union workers at Anaconda Aluminum Company's primary aluminum smelter at Sebree, Ky., walked off the job when their contract expired or, November 15, after rejecting a proposed 3-year contract. The smelter has an annual capacity of 180,000 tons mid accounts for 50% of Anaconda's aluminum production. No talks are scheduled.

Jan 1, 1979

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H20) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained,4 but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process 75. In. all of the processes suggested for the recovery of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation. OCCURRENCE OF HALITE IN POLYHALITE A preliminary estimate of the amount of halite associated with typical deposits of polyhalite may be derived from drill cores, although it should be remembered that only 50 or 60 core tests have been made in the many hundreds of square miles of the Permian basin. From a mineralogical study of 41 of these cores, Schaller and Henderson6 state: In many of the sections of core that seem when viewed by the unaided eye to consist essentially of polyhalite, both halite and anhydrite are present in greatly varying quantities - with very minor quantities of clay and magnesite.

Jan 1, 1934

By D. Harrington

Near the close of the nineteenth century electricity was introduced underground, and the mining industry automatically was confronted with another potential source of fatalities and injuries to mine workers. Electricity has become an increasingly vital factor in the production of goal, particularly in recent years, because of the greatly extended mechanization that has taken place underground. The enlarged use of electrical equipment for cutting, loading, and hauling coal unquestionably increased the potentiality of shock and explosion hazards underground. Electricity may be used in coal mines with minimum danger if electric equipment and power-carrying wires are chosen properly and installed and kept protected by proper safeguards; on the other hand, if vigilance is relaxed in the slightest degree accidents may result. Electrical accidents are caused chiefly by direct contact with electrical equipment or power-carrying wires, by ignition of explosive gas or dust, and by fires of electrical origin. Electricity now ranks fourth as a cause of coal-mine fatalities, not including deaths from explosions or fires of electrical origin.

Jan 1, 1936

The investigations reported herein comprise preliminary studies to evaluate large scale mining systems adaptable to the thicker oil shale deposits in the deeper central portion of the Piceance Creek Basin. The studies include an evaluation of the geology, hydrology and resources of the Basin., evaluation of a potential prototype mine site, synthesis of rock mechanics data on Green River Formation oil shale, selection and preliminary design and cost evaluation of six potential mining systems and a ranking analysis to aid in selecting the most promising system. Results of the ranking analysis indicate the following four systems to be most promising for large scale underground oil shale mining: - Chamber and pillar (using spent shale backfill) - Sublevel stoping with spent shale backfill - Sublevel stoping with full subsidence - Block caving with LHD's Recommendations for phase II are to investigate the above systems in greater detail, refine present cost data, and perform economic evaluations of oil shale mining using these systems.

Jan 1, 1975

By Lee Blackman

The Malheur-Jordan Resource Areas (MJRA?s) is a tract of approximately 6.5 million acres of federal and non-federal land in the southeast corner of Oregon. This study evaluated the Resource Areas' economically recoverable mineral potential based on geological estimates provided in the USGS report (Smith, 1994). The mineral terranes are believed by geologists to contain undiscovered resources. The geological data is probabilistic; with estimates of the possible number of deposits and their grades and tonnages. Possible future development scenarios range from no development to numerous mines. Based on the analysis performed on these terranes, the most likely (in a statistical sense) future scenario for the resource areas would include the potential for two medium sized, predominately gold, mines. These would supply direct and indirect employment of up to about a thousand workers.

Jan 1, 1995

By J. G. Donaldson

Optimum conditions are given for chloridizing pyrite, marcasite, chalcopyrite, arsenopyrite, stibnite, and covellite with chlorine gas. The formation of metal chlorides is affected by the time and temperature of chloridizing, and by particle size of the sample. Chloridizing data also are given for chemically precipitated antimony (III) sulfide and copper (II) sulfide.

Jan 1, 1962

By D. E. Anders

Saturated hydrocarbons from 60 selected samples of a 2,300-foot Green River Formation oil-shale core (Piceance Creek Basin, Colo.) were analyzed by gas-liquid chromatography techniques. Emphasis was placed upon the distribution of normal alkanes and 15 key-branched and cyclic alkanes. The latter compounds consisted of the C15, C16, C18, C19, and C20 chain isoprenoids, the 5-a and 5-ß C27, C28, and C29 steranes, three C30 pentacyclic triterpanes, and perhydro-ß-carotene. The results showed definite evidence of maturation of both the n-alkanes and the branched and cyclic alkanes; however, most if not all of the changes were limited to the indigenous soluble extract and were not the result of additional soluble extract generation from the insoluble kerogen. Source material and environmental variations were important factors in some of the observed differences in the branched plus cyclic alkane compositions.

Jan 1, 1973

By E. G. Davis

Under a memorandum of agreement with Reynolds Metals Co., Richmond, VA, the Bureau of Mines studied the problem of corundum formation on refractory linings in aluminum recycling furnaces. A laboratory test was developed for evaluating refractories in contact with molten recycled aluminum and identifying the mechanism of corundum formation. A test apparatus was designed and constructed to evaluate the performance of refractory samples. Corundum mechanism formation studies indicated that corundum formed on refractories when there is metal penetration. Once corundum forms, it acts as a wick allowing the molten aluminum to move to the surface where it is oxidized, thus causing further growth of the corundum. Phosphoric acid treatment or a spinel mortar coating prevented corundum formation on the 70-and 90-pct-A1203 refractories.

Jan 1, 1988

By Philip C. Good

Red mud residue from Bayer process treatment of Jamaican bauxite was dewatered in batch and in continuous centrifuges. Solids content of the residue was increased from its original value of 20 to 25 percent to about 40 percent by centrifuging. Clear effluent amounting to approximately 40 percent of the slurry liquid was recovered containing dissolved alumina and soda values for potential recycle to the alumina plant" Addition of a chemical flocculant to the centrifuge increased capacity by about 35 percent. Manufacturer's estimate of large-scale equipment requirements, based on data collected in this investigation, was that a proposed installation for dewatering 16,000 tons per day of Jamaican red mud would require twenty-two 24-by 60-inch solid-bowl-type centrifuges. Cost analysis of a proposed installation, based on a Jamaican red mud tonnage of 16,000 per day, is included also.

Jan 1, 1968

By G. W. Jones

One of the major activities of the Bureau of Mines is the promotion of safety in mining and other industries, In this connection, the Bureau determines the explosion hazards' of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. Many dangers are likely to confront men who must enter a building immediately after it has been damaged. Rescue workers must watch constantly for common gases and vapors that may be present in dangerous concentrations in and about demolished, buildings. Fuel gas is the most common source of danger, although refrigerants, gases from furnaces, flues, fires, sewers, and industrial processes, and gas from bomb, explosions in confined places also constitute definite hazards. To rescuers and trapped casualties, these gases offer the hazards of (1) explosion, (2) toxic effects, including asphyxiation and death, and (3) displacement of air so that the oxygen content of the atmosphere is reduced to or below the danger level.

Jan 1, 1944

By C. Özgen Karacan

Longwall mining is an underground mining method during which a mechanical shearer progressively mines a large block of coal, called a panel, in an extensive area. During this operation the roof of the coal seam is supported only temporarily with hydraulic supports that protect the workers and the equipment on the coal face. As the coal is extracted, the supports automatically advance and the roof strata cave behind the supports. Caving results in fracturing and relaxation of the overlying strata, which is called "gob." Due its highly fractured nature, gob contains many flow paths for gas migration. Thus, if the overlying strata contain gassy sandstones or sandstone channels, gas shales or thinner coal seams which are not suitable for mining, then the mining-induced changes can cause unexpected or uncontrolled gas migration into the underground workplace. Vertical gob gas ventholes (GGV) are drilled into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important, first to understand the properties of the gas reservoir created by mining disturbances and, second, to optimize the well parameters and placement accordingly. In this paper, the production rate-pressure behaviors of six GGVs drilled over three adjacent panels were analyzed by using conventional multi-rate drawdown analysis techniques. The analyses were performed for infinite acting and pseudo-steady state flow models, which may be applicable during panel mining (DM) and after mining (AM) production periods of GGVs. These phases were analyzed separately since the reservoir properties, due to dynamic subsidence, boundary conditions and gas capacity of the gob reservoir may change between these two stages. The results suggest that conventional well test analysis techniques can be applicable to highly complex gob reservoirs and GGVs to determine parameters such as skin, permeability, radius of investigation, flow efficiency and damage ratio. The insights obtained from well test analyses can be used for a better understanding of the gob and for designing more effective gob gas venthole systems.

Jan 1, 2009

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1966

By J. D. Sargent

Selenium might be described as a paradoxical element, being either a metal or a nonmetal, a conductor or nonconductor, amorphous or crystalline, colorant or decolorant, and a hydrogenator or dehydrogenator. Selenium was discovered in 1817 by the Swedish chemist, Berzelius, while studying flue dust from the lead chambers of the sulfuric acid works at Gripsholm, Sweden, The ordinary stable form of selenium is a crystalline, grayish solid with semi-metallic luster. It melts at 217° C., boils at 684.8° C., and has a density of 4.79.

Jan 1, 1955

By Neldon L. Jensen

Although ASARCO Incorporated, the only domestic producer, had terminated copper smelting operations and associated recovery of byproduct arsenic trioxide at Tacoma, WA, in 1985, it shipped small quantities of both trioxide and metal from its remaining stocks in 1986. Imports for consumption of arsenic trioxide increased significantly, owing to increased demand for arsenical wood preservatives and the decrease in domestic shipments of trioxide. Prices remained unchanged throughout the year. Development of gallium arsenide integrated circuits, important in advanced military and commercial electronics circuitry, continued to gain momentum during 1986. Domestic Data Coverage.-Shipments of small amounts of arsenic trioxide and metal from remaining stocks by Asarco were reported voluntarily to the Bureau of Mines.

Jan 1, 1988

By Robert M. Doerr

The research objective was to determine the effect of vanadium alloy additions on the oxidation behavior of cobalt-nickel Alloys. Eighteen alloys were reacted with 0 2 at 0.5 arm and 1,351°, 1,389°, and 1,429° K. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with V additions of 0, 0.9, and 2.7 wt pct. Large early deviations from, or changes in, the parabolic rate constant were encountered, but the reaction rate in most cases declined approximately in accordance with the parabolic rate law. Relatively, the vanadium degraded the oxidation resistance most at the highest nickel contents. In some cases, melting of the oxide was inferred from microscopic evidence and X-ray diffraction measurements disclosed the presence of low-melting vanadates.

Jan 1, 1970

By Bruce I. Thomas

The Fairbanks mining district forms an arc 40 miles long and 8 miles wide on the north side of the Tanana Valley in central Alaska. This is a region of broad valleys and rounded hills that range in elevation from 600 to 2,600 feet Lode-gold production started in 1910 and has continued sporadically to the present, but the largest single mine produced only 40 tons per 24-hour day. Total recorded lode-gold production of the district is 241,000 fine troy ounces of gold from ore that averaged 1.32 fine ounces per ton. The ore was mined chiefly from narrow veins and veinlets alined along anticlinal folds at Ester Dome and the Pedro Dome-Cleary area. The only proven reserves are reported to be at the Ryan Lode at Ester Dome and at the Keystone Mines, Inc., holdings in the Pedro Dome-Cleary area. An inferred lode-gold resource for the district of approximately 4,000,000 ounces is considered to indicate only the order of magnitude of the lode-gold potential because of the absence of detailed data needed to evaluate the numerous deposits.

Jan 1, 1973

By John W. Cole

Ore deposits in the? vicinity of Philipsburg, Mont., have been mined continuously since discovery of the Hope mine in 1865. Although originally famed chiefly for its silver production, since about 1917 the district has been the only important producer of battery-grade manganese ore in the United States. Also, it has produced substantial quantities of zinc ore and during World War I and World War II contributed notable amounts of manganese for metallurgical consumption. Nearly the entire production of base metal ores has been mined from the outcrop area of? a dolomitic limestone bed that plunges beneath overlying beds of limestone and shale northward from the outcrop area. The Hope silver mine, with a production record of over $4,000,000, was in one of the overlying limestone beds about 3,000 feet north of the base-metal producing area and about 1,000 feet vertically above the projected downward position of the dolomitic bed that has produced the base-metal ores. Furthermore, the Hope ore bodies were controlled, in part at least by east-west fractures similar to those that controlled the deposition of the base-metal ores.

Jan 1, 1949

By Masami Hayashi

Cost evaluations were made for five processes for producing 100,000 tons of electrorefined copper per year from a chalcopyrite concentrate. The processes were (1) conventional smelting with all furnace gases vented to the atmosphere; (2) conventional smelting with converter gases routed to an acid plant and reverberatory gases vented to the atmosphere; (3) conventional smelting with converter gases routed to an acid plant and reverberatory gases to a citrate system plant; (4) conventional smelting with all furnace gases routed to a citrate system plant; and (5) a modified smelting process in which the concentrate is roasted before being charged to the reverberatory furnace, with roaster and converter gases routed to an acid plant. The total fixed capital costs of the plants were estimated as (1) $56.7 million, (2) $77.4 million, (3) $87.2 million, (4) $73.9 million, and (5) $77.0 million, respectively. Total S02 removal from stack gases as sulfuric acid or sulfur for each process was (1) none, (2) 66 percent, (3) 99 percent, (4) 98 percent, and (5) 78 percent. Assuming no credit for byproduct sulfur or sulfuric acid, total operating costs per pound of electro-refined copper produced were estimated as (1) $0.081, (2) $0.103, (3) $0.119, (4) $0.111, and (5) $0.103, respectively.

Jan 1, 1974

By Thomas O. Llewellyn

This U.S. Bureau of Mines (US8M) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material balance for the year 1989.

Jan 1, 1992

By William A. Beck

The K.T. Dome Mine in Owen and Henry Counties, Ky., has been operated intermittently under several different owners since the early nineteen hundreds. No record of total production is available, but it is said that during 1943 and 1944, while being operated by the Twin Valley Mining Co., 30 cars of zinc concentrates and 10 cars of lead concentrates were shipped. The vein can be traced for about 10 miles along the strike from Lockport, Henry County, to Big Twin Creek in Owen County. It pinches and swells both vertically and horizontally and is reported to average 20 inches in width. In order to develop additional reserves on the property, the Bureau of Mines drilled four holes on the south extension of the vein. Drilling disclosed that the vein dips to the west on the south side of the Kentucky River and is continuous along the strike and in depth. However, the extent of mineralization in the vein varies widely.

Jan 1, 1949