Search Documents

By S. J. Schatzel, W. P. Diamond

Longwall mining alters the fluid-flow-related reservoir properties of the rocks overlying and underlying an extracted panel due to fracturing and relaxation of the strata. These mining-related disturbances create new pressure depletion zones and new flow paths for gas migration and may cause unexpected or uncontrolled migration of gas into the underground workplace. One common technique to control methane emissions in longwall mines is to drill vertical gob gas vent holes into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important to optimize the well parameters, e.g., the borehole diameter, and the length and position of the slotted casing interval relative to the fractured gas-bearing zones. This paper presents the development and results of a comprehensive, "dynamic," three-dimensional reservoir model of a typical multipanel Pittsburgh coalbed longwall mine. The alteration of permeability fields in and above the panels as a result of the mining- induced disturbances has been estimated from mechanical modeling of the overlying rock mass. Model calibration was performed through history matching the gas production from gob gas ventholes in the study area. Results presented in this paper include a simulation of gas flow patterns from the gas-bearing zones in the overlying strata to the mine environment, as well as the influence of completion practices on optimizing gas production from gob gas ventholes.

By William H. Schiffbauer

The Bureau of Mines has developed a passive encoder for range knobs, a device that automates the task of obtaining the range settings from devices or instruments to be input to microcomputers. It is easily constructed and installed and will not disrupt the device to which it is being attached. It consists of a custom knob and a small printed circuit board that has light-emitting diodes and magnetic reed switches attached. A ribbon cable connects it to a microcomputer. This encoder eliminates one source of human error in an automated process.

Jan 1, 1983

By R. Barany

In this paper, closed expressions have been obtained for the frequency spectrum of a Born-Karman square lattice in terms of elliptic and hyperelliptic integrals. This work is part of continuing research by the Bureau of Mines with the thermodynamic properties of metals and minerals. Although other workers have obtained various types of approximations for the general case of the frequency spectrum of a square lattice, no one previously has obtained closed analytic expressions for this spectrum. To understand the optical and thermodynamic properties of crystals, several investigators have studied the distribution of frequencies of normal modes of vibration of the crystal lattice. Born and Karman3 laid the foundation for the theory of lattice dynamics and obtained detailed results for the case of a one-dimensional lattice. Blackman4 used numerical techniques to estimate the frequency distribution of a two-dimensional square lattice. Mbntroll5 analytically determined the frequency distribution of a square lattice for a particular value of the force constants. He also studied the more general problem and obtained some analytic approximations, using the method of moments. However, the calculations by this method were so difficult that it was not always practicable to carry them out. Van Hove6 and Montroll7 studied the nature of the singularities in the frequency spectrum of both a two and

Jan 1, 1962

By P. L. Woolf

Seven evaluation tests with blast furnace iron bearing burden materials are described. The effects of pellet strength, fines in the burden, decreasing slag volume, pellet size, eliminating stone with superfluxed sinter, and eliminating stone by prefluxing the pellets were determined. Fluxed pellets and fluxed sinter made with the same ore fines were compared. The tests were conducted under cooperative agreements between the Bureau of Mines and North American steel companies. The objectives were to improve blast furnace practice, expand and develop understanding of the operation and theory, quantify the effects of changes, and explore the limitations of operability. This work was part of an extensive program of blast furnace research in experimental blast furnaces at Bruceton, PA conducted in the years 1958 to 1967.

Jan 1, 1984

By D. Eugene Rannels, Yu-Chen Lee

"Lee, Yu-Chen, and D. Eugene Rannels. Alveolar macrophages modulate the epithelial cell response to coal dust in vitro. Am. J. Physicl. 270 (Lung Cell. Mol. Physiol. 14): L123-L132, 1996.-The response of the alveolar epithelium to coal dust exposure is poorly understood. Coal or other dusts may act on the epithelium directly or indirectly through nearby alveolar macrophages (AM) that produce cytokines and other soluble products. AM and type II pneumocytes (T2P) were thus exposed to dust in coculture to evaluate their possible interactions. Anthracite coal dust PSOC 867 increased synthesis of extracellular matrix (ECM) components by T2P. AM alone did not produce ECM. Similarly, coculture ofT2P with AM (3.75:1) had little effect on epithelial ECM synthesis. In contrast, coculture ofT2P with AM significantly increased PSOC 867 effects on T2P rates of ECM synthesis, ECM fibronectin content, and T2P levels of fibronectin mRNA. AM-conditioned medium did not change the PSOC 867 effect on T2P. Neither control nor PSOC 867-treated AM on Falcon culture inserts (0.45-µm pore size) over T2P stimulated ECM synthesis by either untreated or dust-exposed epithelium. Thus AM-mediated changes in ECM synthesis by PSOC 867-treated T2P require close cell-cell interactions, suggesting a role for cell-cell contact or for short-lived soluble mediators of the AM effects. DEVELOPMENT OF PNEUMOCONIOSIS, a chronic disease of coal workers that results in pulmonary fibrosis and low lung compliance, is associated with inhalation of mineral or coal dust in the work place (14). Although the pathology of pneumoconiosis has been studied extensively, cellular mechanisms that cause changes in lung structure and function are not fully understood. Particulate matter that enters the respiratory system distributes according to size, with larger particles being removed in proximal airways. Dust components of small size may enter distal alveolar region, which is populated by two types of epithelial cells, type I and - type II cells, and by alveolar macrophages (16). Each of these cell types may interact with inhaled particles, but only the effects of coal dust on alveolar macrophages have been studied extensively. Less is known regarding the response of the alveolar epithelium, or of effects on epithelial cell-alveolar macrophage interactions, in the dust-exposed lung.Function of the alveolar epithelium is well known to be influenced by the underlying basement membrane, or extracellular matrix (28). Alveolar epithelial cell extracellular matrix interactions, which may involve modulation of cell migration, attachment, or differentiation (17), are reflected in type II cell morphology, metabolism, secretory activity, hormone responsiveness, lamellar body content, and gene expression (21). The extent to which basement membrane modulates differentiation of the overlying epithelium is determined by both molecular composition and three-dimensional structure of the matrix. Type II epithelial cells in vitro synthesize, secrete, assemble, and degrade a variety of basement membrane components, including laminin, fibronectin, type IV collagen, and thrombospondin (22, 27). How expression of these components is regulated, directly or indirectly, upon exposure of the alveolar epithelium to injury by coal dust or by other particulates remains to be resolved."

Jan 1, 1998

By G. R. Hopkins, E. W. COCHRANE

The number of completed petroleum refineries in the United States continued to decline in 1937 , but the total capacity to process crude oil continued to increase . These facts were ascertained in the Bureau's annual canvass of refinery capacity as of January 1 , 1938 . Several important changes were made in the census questionnaire for January 1 , 1938 . First , the basis of reckoning cracking capacity was changed from cracking stock charged to cracked gasoline produced . Although this is a definite improvement , in that it is no longer necessary to consider the yield , it is unfortunate that the data for January 1 , 1938 cannot be compared with cracking - capacity statistics since 1925. Other changes or additions included separating capacity at operating plants into that actually operating and that closed down ; collecting data on capacity added or retired during the previous year ; breaking down idle capacity according to physical status ; and separating new capacity into that built for replacement and that built to augment existing capacity . Prior to January 1 , 1938 , the total capacity of an operating plant was listed as " operating " even though some stills might have been closed down ; furthermore , the only capacity reported as being under construction was that of new plants that were being built on January 1. To make the statistics clear , the totals for the United States as of January 1 , 1938 , are given on both the old and the new bases . On January 1 , 1938 , there were 551 completed plants compared with 572 the previous year . Ten new plants were under construction on that date compared with 11 the year before . The greatest number of completed plants recorded was 632 on January 1 , 1936 ; since then , competitive conditions , particularly in the East Texas field , have been instrumental in reducing the number of small independent plants . The total crude- oil capacity of the completed refineries on January 1 , 1938 , was 4,351,151 barrels , of which 3,970 , 196 barrels ( 91 percent ) represented the capacity in actual operation and 380,955 barrels ( 9 percent ) was shut down . The " shut -down " capacity ( 199,875 barrels on the old basis ) was the lowest since pre- depression days , chiefly because numerous idle East Texas plants were removed from the list . The new method of compiling the statistics sheds considerable light on excess crudeoil capacity , which has been the subject of considerable speculation in recent years . The highest daily average crude runs to stills reached in this country was about 3,460,000 barrels in September 1937. At that time , the total crude - oil capacity was about 3,925,000 barrels . This indicates that at peak operation the excess capacity was somewhat less than

Aug 1, 1938

By William H. Pomroy

Fires in underground metal and nonmetal mines pose a threat to the safety of underground miners and to the productive capacity of this Nation's mines. Contaminated air (smoke, carbon monoxide, and other products of combustion) is the primary life safety hazard created by a mine fire. The most reliable defense against the hazard posed by the rapid spread of contaminated air underground is early warning fire detection and rapid evacuation. This Bureau of Mines report describes the design and operation of four prototype early warning fire detection systems, for underground noncoal mines, presently undergoing prolonged in-mine testing by the Bureau. The systems are described within the context of the underground mine environment.

Jan 1, 1985

By Alexander May

This report describes a new method of weighing based upon observing the apparent weight of an object ill two separate pure gases. The method is presented in terms of experimental data which prove its soundness, but does not attempt to show the maximum accuracy possible with this technique. The new method incorporates the underlying principle that the apparent weight of an object is a linear function of the density of the atmosphere in which the object is weighed. The coefficients of this linear function are the true mass and volume of the object. From this functional relationship the true mass and volume of the object may be determined.

Jan 1, 1970

By W. A. SLOAN, G. L. Oldright, J. D. Sullivan, E. K. PRYOR, A. F. HALLET, R. S. Dean, S. L. BROWN, F. S. Wartman, A. J. Thompson

Lack of sufficient publication funds has resulted in the accumulation of considerable unpublished experimental work on copper metallurgy by the Bureau staff . The present report gives extended abstracts of this work , as well as a discussion of the best direction for future efforts . The experimental work reported in this series of papers was done in cooperation with the University of Arizona , Tucson , Ariz . The investigations covered in the third , fifth , and seventh papers were done under the direction of G. L. Oldright and the remainder under the direction of V. H. Gottschalk .

May 1, 1934

By W. M. Dressel

The objective of the research reported in this publication of the Federal Bureau of Mines was to devise a mineral dressing procedure that would concentrate zinc silicate minerals from certain deposits in southwestern Missouri. The best flotation results were obtained by batch laboratory flotation using sulfidizing agents and ethoxylated cocoamine. The flotation concentrate contained 70 percent of the zinc at a grade of 47.8 percent. Gravity concentration tests showed that 55 percent of the zinc could be recovered at a grade of 48.3 percent.

Jan 1, 1961

By W. S. Landers

This report presents a study by the Federal Bureau of Mines of technical factors related to the production of special carbon and tar from selected Wyoming coals. Certain Wyoming high-volatile bituminous and subbituminous coals were processed in bench-scale apparatus to determine potential carbonization yields and in pilot plant retorts to produce sufficient char and tar for testing. These tests have shown that a critical selection of coal is necessary when the coal is processed for a specialized carbon. Generally high yields of tar are obtained from low-temperature carbonization of Wyoming high-volatile bituminous and subbituminous coals, and the yield of tar usually increases with increase in rank within this range of coals. The production and evaluation of industrial carbons from Wyoming coals by using pilot plant and bench-scale techniques is part of the continuous program of upgrading western coals. It has been found that: 1. Most Wyoming coals are nonagglomerating and may be carbonized in fluidized systems. Chars produced in pilot plant retorts at low temperatures contain about 17 to 23 pct, residual volatile matter and are easily ignited. These chars appear suitable as power plant fuel. The tar-plus-light-oil yields range from 14 to 40 gal./ton of raw coal processed. 2. Wyoming high-volatile coals produce a slightly smaller and somewhat weaker coke than currently mined Western United States high-volatile coals used commercially as blending stock in metallurgical coke production.

Jan 1, 1961

By R. V. Lundquist, H. Leitch

Sodium aluminate is the principal aluminum compound formed in the sinters prepared by the lime - soda sinter process for recovering aluminum from silicate source materials . The properties and characteristics of this compound were studied to improve the efficiency of the process . Crystalline sodium aluminate was prepared by sintering stoichiometric quantities of soda ash and calcined alumina for 1 hour at 1,250 ° C. The extent of aluminum extraction from sodium aluminate was determined in water and in solutions of NaOH and Na₂ CO3 . Nearly complete extraction of aluminum from sodium aluminate was achieved only in solutions containing free NaOH in excess of that supplied by the salt through hydrolysis . About 42.2 to 68.8 percent of the aluminum was extracted in water or in solutions of Na₂ CO . The precipitation of alumina trihydrate from sodium aluminate solutions was shown to be part of a continuous , reversible reaction according to the equation Al (OH ) A1 (OH )3 + OHThe reverse reaction dissolves alumina trihydrate in NaOH solutions to produce sodium aluminate . Approximate equilibrium concentrations were determined for the reaction at 30° , 50 ° , and 70 ° C. False apparent equilibrium conditions for the dissolution reaction appear when only a small excess of alumina trihydrate is present in the NaOH solutions . A large excess of alumina trihydrate must be present before the true equilibrium point is assured . The engineering significance of the data is summarized , showing controls that should be exercised for a successful and efficient process .

Jan 1, 1964

By G. R. Fitterer, C. H. Herty

"INTRODUCTION Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis in easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot—top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel.For a large tonnage of steels which go into articles manufactured by deep—drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low—carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, — that is to say, deoxidized with manganese and perhaps a small amount of aluminum, — the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper—central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low—carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel."

Feb 1, 1931

By Ralph Husack, J. W. Eckerd, G. A. Brady

The effect of gamma radiation on Pennsylvania anthracite and on reactions between anthracite and other materials was studied using a shielded , selfcontained 23,000 - curie cobalt 60 source . When anthracite was exposed to air at 65° C the reaction with oxygen was greater in the presence of radiation. than in its absence . Although drop- shatter tests indicated that exposure to radiation decreased the resistance to breakage of anthracite , this evidence of structural weakening was not supported by the results of grindability or particle- size studies . Irradiation caused definite changes in the gases evolved from evacuated samples of anthracite ; the percentages of hydrogen and carbon dioxide were increased, and the methane concentration remained unchanged . Carbon monoxide was evolved only from the unirradiated samples . Electron paramagnetic resonance (EPR ) measurements indicated large differences between evacuated samples and those exposed to air . There was little or no difference between irradiated and unirradiated samples , except that the free- radical content of unirradiated samples of anthracite increased progressively with higher temperatures of evacuation , but in the case of irradiated samples , no such behavior was found . Attempts to produce carbon disulfide and calcium carbide by reacting anthracite with sulfur up to 120 ° C , and with calcium oxide up to 400 ° C , were unsuccessful .

Jan 1, 1964

By Stanton L. Tainter

When the disruption of gold mining stopped the usual source of siliceous flux needed by copper smelters , sandstone copper deposits in northern Arizona offered possibilities as a source of the flux during the war emergency . The Federal Geological Survey , while making a comprehensive survey of sandstone copper deposits , investigated the Warm Springs mining district in northcentral Coconino County in August 1943. A month later , J. H. Hedges , chief of the Tucson Division , Mining Branch , Bureau of Mines , examined the operations in connection with an application for an access road . Both investigations concluded that the district , as an emergency source of copper-bearing siliceous flux , had considerable merit , provided high prices for copper continued in effect . Early in 1944 , V. M. Ryan and S. B. Atherley requested assistance from the Bureau in exploring various deposits on their property . The Bureau / drilled 152 holes , aggregating 3,756 feet , on the Petoskey and Mackin groups of claims . This report is based upon churn drilling done under contract from October 7 to November 25 , 1944 .

Feb 1, 1947

By D. W. Boley

This report contains the results of an analysis of the Logan oilfield, Hocking County, Ohio, and predicts the recovery of oil from the Clinton sand by waterflooding. Core analyses, electrical and radioactivity well-survey logs, reservoir-fluid analysis, and geologic and production data were used for this study. Considered in the evaluation were the reservoir geometry, depth, lithology, continuity of the rock properties, fluid saturations, fluid characteristics, rock wettability, and relative permeability-fluid saturation relationships. The study indicates that a properly engineered waterflood should recover approximately 135 barrels per acre-foot of effective sand. The predicted recovery warrants the initiation of a pilot waterflood in this field.

Jan 1, 1965

By Frank E. Cash

The compensation-insurance rates for quarrying in North Carolina are 11 times higher than for the State?s major industry, textiles. Some operators are willing to accept this as representing the ratio of existing hazards. This was not true of the management of the Southern Aggregates Corporation, and in 1935 it tools definite steps to correct the idea of its local officials and employees that loss of life and limb in quarries is inevitable. ACKNOWLEDGMENTS The authors acknowledge gratefully the assistance and information concerning these operations furnished by H. M. Shaw, safety director (also secretary and treasurer), Southern Aggregates Corporation, Raleigh, N. C.; by the following superintendents: J. H. Rodgers, Blair Quarry, Blair, S. C.; J. D. Lane, Greystone and Rolesville Quarries, Henderson, N. C. ; J. H. Arthur, Guilquarry, Stokesdale, N. C.; J. H. Watkins, Rockton Quarry, Wendell, N. C.; P. A. Wellenborne, Reidsville Quarry, Reidsville, N. C.; and J. L. Kirchin, Woodleaf Quarry, Woodleaf, N. C.; by the various foremen at the plants, and by Murry Id. Grier, safety engineer, North Carolina Department of Labor, Asheville, N. C.

Jan 1, 1940

By W. T. Westbrook

This Bureau of Mines report contains methods for analyzing iron are for total iron, ferrous iron, metallic iron, silica, manganese, aluminum, calcium, magnesium, phosphorus, titanium, carbon, sulfur, moisture loss, and ignition loss by wet chemical methods. Some are modifications of standard umpire methods; others have been developed by the Bureau of Mines to provide a com-bination of speed and accuracy. They are suitable for a high volume of samples and/or control situations, and for situations in which instrumental results must be verified. These methods have been used to analyze taconites, native ores, some foreign ores, and metallurgical products.

Jan 1, 1975

By E. C. Baker

Costs of disposing of steel slag are estimated based on the present method and a proposed alternate method for a steel mill in the Pittsburgh area. Estimated cost data were calculated by the Bureau of Mines and do not reflect the investment and operating costs and credits of a specific steel mill and processing plant. The alternate method of steel slag disposal would result in an appreciable cost savings to the mill and concurrently supply the industrial and commercial markets with low-cost, high-quality construction materials.

Jan 1, 1970

As fulfillment of the requirements of Contract H0387019 for the United States Department of the Interior, Bureau of Mines, a complete field kit, for performing on-site determinations of individual employee Time Weighted Average (TWA) exposures to nitrogen dioxide (NO2) and nitric oxide (NO), has been developed by MDA Scientific, Inc. This report provides background information and experimental data validating the use of this kit with confidence to ? 10 percent accuracy.

Jan 1, 1981