Search Documents

By P. G. Pigott

This Bureau of Mines laboratory research demonstrated that building bricks meeting ASTM specification C62-66 for grades SW and MW of FBS-type bricks can be produced from waste copper mill tailings. Waste tailings from accumulations at Magna, Utah, Anaconda, Mont., and Hayden, Miami, and San Manuel, Ariz., were dry-pressed into bricks, and the products were tested in accordance with ASTM Designation C67-66 on sampling, and testing of brick. An evaluation derived from pilot-plant production of similar brick at the Coal Research Bureau of West Virginia University indicated the production cost to be about $34 per 1,000 bricks. Utilization of such mill tailings on a commercial scale would eliminate the need for digging new pits for brick raw material production, conserve natural resources, and simultaneously remove potential sources of air pollution.

Jan 1, 1971

By S. Ralph Austin

Emanation coefficients of 950 samples of domestic uranium ore were successfully and rapidly determined with fair precision by modifications of the closed-can, gamma-only assay method, using commercially available or similar equipment. Coefficients range from <1 to 91 percent. Emanation varies considerably within each mine and area, but distinct differences among major mining areas were found, ranging from 7.5 percent for Moss Back Member, Chinle Formation, Southwest Lisbon Valley, Utah, to 56.6 percent for Ft. Union Formation (?), Powder River Basin, Wyoming. Coefficients also vary with (1) uranium mineralogy; (2) radium mineralogy; (3) lithology of host rocks; (4) grain size of uranium and radium minerals; (5) comminution of ore; (6) estimated porosity and permeability; (7) moisture content; (8) ore grade; (9) supposed mobility of deposits; age of deposits is unknown but limited by (10) age of host rocks which shows only doubtful correlation with emanation. Data obtained may be used to evaluate effects of investigated parameters on radon concentration in mines and thus to select efficient control measures. Drill-core emanation data allow estimates of probable radon problems in undeveloped deposits.

Jan 1, 1978

This Bureau of Mines report reviews the information presented at the Sixth Mineral Waste Utilization Symposium cosponsored by the Bureau of Mines, U.S. Department of the Interior, and the IIT Research Institute. Environmental scientists and engineers from nine countries participated in the symposium, which was held May 2-3, 1978, at the Chicago campus of IIT Research Institute. The 56 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial wastes, and scrap metal are summarized herein.

Jan 1, 1980

By Pamplinm J. W.

"INTRODUCTION For the past six years the United States Bureau of Mines in cooperation with the University of Alabama, Tuscaloosa, Ala., the Missouri School of Mines and Metallurgy, Rolla, Mo., and certain operating companies of the Florida land-pebble phosphate district have conducted an investigation to determine the amenability of phosphatic sands to concentration. 4 This paper discusses briefly an investigation of the concentration of fine phosphatic sanads of the land-pebble district of Florida. The process used - namely, the tabling of material previously given a selective oiling treatment - is new in its application to the phosphate industry, although old in principle.The feed to the standard phospidate washery is a hydraulically wined mixture of phosphate pebbles, quartz sand, and clay in which the quartz sand grains are segregated in the fine sizes. Me standard method of concentrating (washing) consists of wet-screening. at about 20 mesh to recover the plus 20-mesh material. 5 Lately some of the washeries have introduced hydraulic classifiers for sizing of the screen undersize to recover the coarser spigot products, but even this additional treatment allows much of the fine phosphate to be wasted."

Dec 1, 1932

By D. J. Parker

Because of its convenience and availability, natural gas (and to a much less extent manufactured gas) in being used more generally throughout the country for domestic and industrial purposes. With this use, specific and little-recognized hazards have arisen owing principally to the fact that the public and the consumer lack knowledge of the explosive property of this fuel. During the past 8 years gas explosions hove occurred in public and private buildings with loss of more than 300 lives and injury to many others. Such appalling catastrophes can and will be prevented if and when the necessary precautions are taken in the construction of buildings and the installation and maintenance of gas lines and gas appliances, plus adequate supervisions inspection, and education.

Jan 1, 1941

By G. L. Fitzpatrick

Preliminary results of an experiment in seismic holography indicate that the techniques of acoustical holography may be successfully used with seismic waves to determine the size and general shape of underground objects. This experiment was carried out under field conditions on a moderately large scale compared with the typical laboratory experiments in acoustical holography. The object to be mapped was a 100-foot-diameter, spherical, low-velocity zone of explosively fractured rock in oil shale at an average depth of 80 feet. The seismic wavelength of the Fourier component wave used in making the seismic holograms was 50 feet at a frequency of 140 cps. The hologram sampling aperture was 226 feet square and was sampled by 441 geophones in a 21 by 21 rectangular array. One novel aspect of the experiment was the use of a wide-band polychromatic explosive source of seismic waves rather than a narrow-band quasi-monochromatic vibrator source. A successful laser reconstruction of the object image from a lensless Fourier-transform hologram in the form of a 5/l6-inch-square photographic transparency is illustrated. The size of the underground object measured from the laser reconstruction of the object and the size inferred from a knowledge of the amount of explosives used to fracture the site and the tensile strength of the oil shale are found to agree.

Jan 1, 1972

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Arkansas has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251 of which this is the tenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of which deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated. and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By C. H. Riggs

"INTRODUCTION The injection of gas into the McClosky limestone in the adjoining, Griffin and New Harmony field in Indiana and Illinois and resulting increases in oil and gas production from this zone ore described in this report.Since 1911, the use of compressed air or as to increase oil production by supplementing natural reservoir energy has been widely adopted, and has resulted in the recovery of much additional oil, which otherwise would have been left underground. In many of the newer oil fields, including Griffin and New Harmony, a part of the compressed residue gas from natural gasoline plants is returned to the reservoir as a secondary method to increase oil and gasoline production. Part of the injected gas is stored underground for future use.By presenting data on many secondary recovery operations in a series of reports 5-9/ the Bureau of Mines has sought to stimulate interest in secondary recovery as a means of increasing oil recovery and current oil production for wartime needs. Most of the elder fields in the United States produce oil from sandstone reservoirs, and probably more than 90 percent of secondary recovery operations have been developed in oil bearing sandstones. During recent years, the volume of oil obtained by primary methods from limestone reservoirs has increased steadily, but as yet little has been done to recover, by secondary means,,the large volumes of oil left in limestone reservoirs when primary methods production are no longer profitable. Because of inherent differences in the origin and nature of the pore spaces between sandstones and limestones and because of differences in permeability and fluid content, secondary recovery methods, which are successful in sandstone-reservoirs, are not always applicable to limestones. Not much he been written concerning secondary recovery operations in limestone reservoirs, and few data are available to assist operators in developing such secondary recovery projects."

Jul 1, 1945

By Z. J. Fink

Ultraviolet-visible and infrared emission spectra from propagating methane-coal-dust-inhibitor mixtures have been obtained in a 0.2-by 0.2¬by 5.3-m vertical duct over a range of flame speeds from 2 to 100 m/sec. Results serve as a basis for the design and evaluation of thermal radiation detectors for triggered barriers that suppress ongoing mine explosions. Of particular significance is the large continua superimposed on the methane-air spectra when small amounts of coal dust are present and the variation of emissivity with infrared (IR) wavelength in dust flames. In conjunction with the spectral measurements, studies of flame speed, particle size, gas sampling plus thermodynamics, and dust sampling are presented and discussed in order to gain insight into the more fundamental aspects of propagating explosions. Sampling results have shown that only a near-stoichiometric amount of dust is consumed in the flames studied even though initial concentrations are five times stoichiometric. Difficulty in propagating coal-dust inhibitor flames of realistic mine characteristics in a cold-walled laboratory duct has been encountered. A simplified analysis of the flame zone utilizing spectral and sampling results indicates that the stability of slowly propagating flames is more dependent upon thermal radiation than upon convection losses to the walls. It is predicted that thermal radiation losses will make any measurements of coal dust burning velocities, "quenching diameters," or flammability limits more apparatus dependent than those corresponding to gaseous fuels.

Jan 1, 1974

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and ran extensive literature has resulted, Usually each individual paper has placed &apos;emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By W. C. Babcock

This report covers Phase V of .a continuing program to apply a new liquid membrane process called coupled transport to the recovery pf metals from hydrometallurgical leach solutions. During this phase of the program, a membrane system of moderate scale was constructed and field-tested at the Exxon Highlands Mine and Mill Co. site near Douglas, Wyoming. The test unit contained four hollow-fiber membrane modules, each with 100 ft2 of membrane area. In the field tests, about 1000 gallons per day of leach solution was processed. The unit was operated on the leach solution for about 50 days. Leach solution entering the unit contained 100 ppm uranium. This concentration was reduced to about 5 ppm by coupled-transport treatment, and the uranium was concentrated to about 2 wt% as a uranyl carbonate product. Under these conditions, a transmembrane uranium flux of about 2.5 lb/ft2-year was obtained. An economic analysis showed that the cost of recovering uranium from this leach solution via coupled trans-port is about $1.20/lb. At higher concentrations of uranium in the leach solution this cost is reduced. For example, at 1000 ppm the cost of uranium recovery is about $0.30/lb.

Jan 1, 1983

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and an extensive literature has resulted. Usually each individual paper has placed emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By J. P. Capp

The Bureau of Mines conducted field-scale experiments in underground gasification of coal with oxygen-enriched air. A path about 140 feet long was linked at the rate of LO feet per day through a coalbed hydraulically fractured with a mixture of starch gel and sand. During the best gasification period, which extended for 2-1/2 days, 785,000 std. c.f. per day of 124-B.t.u. gas was produced. In other periods the heating value at times was almost 300 B.t.u. per std, c.f,, but sustained production of such gas was not achieved. During gasification, a total of 50 tons of coal was gasified and 114 tons of coal was carbonized. Approximately 12 million B, t .u. per foot of nominal path was recovered at the surface.

Jan 1, 1962

By Harold J. Miller

Loading and haulage of run-of-mine ore is frequently the highest cost in underground mining operations. These costs can be significantly reduced by use of belt conveyors, a common practice in coal and similar soft miner ii mines. This is particularly true if oversize ore and rock can he eliminated prior to conveying; thus producing a demand for crushers near the production areas. Portable feeder-breakers are extensively used in conveyorized mines, but no suitable, equivalent equipment, is available to provide these benefits to hard rock mines of low to medium headroom. A hard rock crusher capable of easy movement and readily disassembled would allow use to belt conveyors and could improve the general safety and productivity of any underground ore hauling system. This report summarizes proposals and findings made in conjunction with the newly designed M-44 Low Head Portable Crusher which is believed well capable of meeting the requirements of a "portable, underground, hard rock" machine as previously defined in earlier reports. Data gathered by use of the 1/4 Scale Model of the M-44 has substantiated and verified the concept sufficiently to justify construction of a full-size machine for further testing under actual mine conditions.

Jan 1, 1978

By Sam S. Taylor

Disposal of brines produced with crude petroleum and natural gas is a continually increasing problem. The necessity for studying this problem has been realized more generally in recent years, and in August 1934 an agreement was made between the Kansas State Board of Health and the United States Bureau of Mines to conduct a cooperative technical study of methods of brine disposal. To date one paper in the technical press4/ and three reports5/6/ have been published in which are given results of studies carried on under this cooperative agreement. In the Mid-Continent fields, the methods used most generally for handling oil-field brines are: (1) Impounding in evaporation ponds; (2) controlled diversion into surface streams; and (3) injection into subsurface formations through wells assigned for this purpose. Various States recognize one or more of the methods as legally authorized procedure. Impounding brine in ponds and solar evaporation have proved inadequate as a general rule, owing, usually, to the porous nature of the soil, the low rate of evaporation, or both. Diversion, of

Jan 1, 1937

By Sam S. Taylor

Disposal of brines produced with crude petroleum and natural gas is a continually increasing problem. The necessity for studying this problem has been realized more generally in recent years, and in August 1934 an agreement was made between the Kansas State Board of Health and the United States Bureau of Mines to conduct a cooperative technical study of methods of brine disposal. To date one paper in the technical press4/ and three reports5/6/ 7/ have been published in which are given results of studies carried on under this cooperative agreement. In the Mid-Continent fields, the methods used most generally for handling oil-field brines are: (1) Impounding in evaporation ponds; (2) controlled diversion into surface streams; and (3) injection into subsurface formations through wells assigned for this purpose. Various States recognize one or more of the methods as legally authorized procedure. Impounding brine in ponds and solar evaporation have proved inadequate as a general rule, owing, usually, to the porous nature of the soil, the low rate of evaporation, or both. Diversion of

Jan 1, 1937

By H. L. Riley

At the Southern Experiment Station, Tuscaloosa, Ala., reports are prepared from time to time on results of washability studies of coal from important beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. The principal objective of a washability study is to obtain technically and commercially important data to aid in determining the best methods for preparing and utilizing the Nation&apos;s reserves, particularly of coking coals. Such information is also important from the standpoint of conservation, because it facilitates the selection of preparation methods that will yield an acceptable product with a minimum loss of coal to the rejects.

Jan 1, 1958

By T. L. Johnston

The Dobbins property, about 4-1/2 miles northeast of Cartersville, Ga., was fist operated in 1866, it is the oldest manganese mine in Georgia and one of the oldest minus in the United States still producing manganese ore. Changes in ownership, lessees, and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property.

Jan 1, 1942

By T. L. Johnston

The Dobbins property about 4-1/2 miles northeast of Cartersville, Ga., was first operated in 1866. It is the oldest manganese mine in Georgia and one of the oldest mines in the United States still producing manganese ore. Changes in ownership lessees and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property

Jan 1, 1942

By O. C. Blade

Total sales of diesel fuel in the United States continue to Increase. This growth is due primarily to two causes: More conversion to diesel units by the rail-roads In recent years, and the greater use of diesel engines in trucks, busses, and tractors. Following are some figures on the distribution of the fuel computed from data issued by the Bureau of Mines.2/ [ ] Deliveries of diesel type fuel from refineries totaled 91,522,000 barrels during the first six months of 1955,3/ corresponding figure for 1954 was 91,170,000 barrels. Information on the properties of this engine fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1955