Search Documents

By E. S. Leaver

The mineral value in the ores from the Mother Lode mining districts of California is almost entirely gold, Although many mines have produced extremely high-grade ore the usual mill grade averages approximately $7.00 gold per ton. Fully 80 per cent of the gold has been and is now being recovered by amalgamation. Various methods have been introduced to recover the gold that was not obtained by the amalgamation processes. They include vari¬ous kinds of gravity concentration which in some cases were followed by chlorination or cyanidation. The usual practice includes only stamp battery, plate-amalgamation, and vanner concentration. In the very early practice the tails were run to waste through the main drainage streams of the different mining districts. During later years very large storage dumps have been impounded. These old tails, together with those being saved from present mills, furnish the problem discussed in this article. The clean sand portion of these mill tails is amenable to the usual cyanidation. The slime portion contains the major amount of the gold lost, but it also contains 1-1/2 to 3 per cent carbon, which precludes direct cyanidation of this part of these low-grade waste tails. The black carbonaceous slime portion is the particular problem considered in this report.

Jan 1, 1930

The Tenth International Conference of Directors of Safety in Mines Research was held in the United States from September 28 through October 2, 1959, at Hotel Webster Hall, Pittsburgh, Pa. The Conference was organized by the Federal Bureau of Mines. In accord with the program outlined at the Ninth Conference (1956, Heerlen, Holland), the papers submitted dealt with the following three subjects: 1. Safety of coal mine explosives 2. Explosion hazards in mines 3. Ignition and fires in mines Seventy papers were presented. There were eight technical sessions followed by an extended tour of the Bruceton facility of the Bureau of Mines on October 2. Simultaneous translation was provided in the three official languages of the Conference--English, French, and German.

Jan 1, 1962

By Alla D. Mah

The energies of combustion of zirconium carbide and hafnium carbide were measured by combustion calorimetry and the heats of combustion and formation. of zirconium carbide and hafnium carbide were derived . The results are-- ZrC AH298.15 ( combustion) = -308.60 ± 0.55 kcal /mole , AH298.15 ( formation) -47.0 ± 0.6 kcal /mole , AH298.15 = HfC (combustion ) = -306.08 ± 0.20 kcal/mole , AH298.15 ( formation) -52.3 ± 0.4 kcal /mole . = INTRODUCTION This report contains the results of calorimetric measurements to obtain the heats of formation of zirconium carbide ( ZrC) and hafnium carbide ( HfC) . The work was conducted as part of a Bureau of Mines program for determining the heats of formation of oxides , carbides , and nitrides by combustion calorimetry . Combustion calorimetry is one of the most precise calorimetric techniques . The chief obstacle to obtaining accurate heat of formation values for carbides , and the chief reason for the variation in the results of different investigators , is the lack of purity of the carbide samples . Corrections for impurities always involve assumptions which lead to uncertainties . In general , a large impurity correction is accompanied by a large uncertainty in the final result .

Jan 1, 1964

By E. Divers

This Bureau of Mines report presents results of an underground evaluation to determine the respirable dust and gas control effectiveness of a combined (push-pull) face ventilation system for coal mines. The system utilizes both blowing and exhaust curtain, continuous miners equipped with radio remote control, and flight conveyors. Bureau of Mines tests showed a 97% reduction in respirable dust concentrations from the usual cab position on the continuous miner to the remote control operator's position. This allowed the remote control operator to be well within, and the usual cab position to exceed, Federal respirable dust standards. Tests utilizing a safe tracer gas, sulfur hexafluoride (SF6), to determine the face ventilation effectiveness of the combined blowing and exhaust system showed that the system also has excellent methane dispersion capability. Where wide entries permit, this combined face ventilation system and use of remote control can be a very effective method for dust and gas control.

Jan 1, 1982

By V. E. Edlund

This report presents the results obtained in a study of the technical feasibility of recovering a usable pig iron by pyrometallurgical treatment of typical copper reverberatory slags . The iron in the slag was readily reduced with carbon , but the copper and sulfur content of the metal was best controlled by a three - stage procedure comprising ( 1 ) melting the slag with pyrite to remove copper as a low- grade matte , ( 2 ) smelting the partly decopperized slag with fluxes and carbon to reduce the iron , and ( 3 ) refining the impure iron alloy from step 2 with a flush slag to remove sulfur and residual copper . Laboratory - scale tests demonstrated that washing with 8 wt pct of pyrite lowered the copper content of a typical reverberatory slag from 0.58 to 0.12 Subsequent smelting of a mixture composed of 70 pct decopperized slag , 25 pct lime , and 5 pct coke reduced 84 pct of the iron to metal containing 2.27 pct sulfur . This metal then was successfully desulfurized by treatment with a basic flush slag to produce a finished metal that contained , in percent , 93.5 Fe , 0.02 S , 0.26 Cu , and 4.9 C. Overall recovery of iron under the conditions of trial was about 80 pct . This could be increased if higher tolerances for copper could be accepted . Commercial processing would be accomplished in three furnaces with molten materials passing from one to another . Currently produced smelter slag could be treated fairly inexpensively , because the molten product would require only a little additional heat to produce an iron byproduct that undoubtedly would be attractive to local foundries .

Jan 1, 1964

By L. J. Kane

Chemical processes using coal often require economical removal of dust from high-temperature gases. Laboratory-scale investigations by the Federal Bureau of Mines have shown that an aluminum silicate fiber is suitable for filtering dust from gases at 1,800° F. The effects of the bulk density of the filter, rate of gas-flow, concentration of dust in the filter, fiber diameter, depth of filter, and concentration of dust in the feed gas on removal efficiency, pressure drop, and capacity of the filter to hold dust were studied. The laboratory filters were difficult to construct because the fibers were longer than the tube diameter. This caused irregular distribution of fiber that permitted dust-laden gases to leak through channels developed in the filter. Leaks also formed between the filter and the tube wall, but this was minimized by improved filter design. However, edge leaks and leaks through channels in the filter probably would be insignificant in properly constructed filters of industrial size. As the concentration of dust in the filter increased, the efficiency of the low-density filters decreased, contrary to expectations, probably because a higher percentage of the dust passed through channels that developed in the filter. The efficiency of high-density filters, however, increased with the concentration of dust in the filter. Results indicate that loosely packed filters would have a longer life than tightly packed filters at the expense of efficiency. As regeneration or replacement of stationary filters is difficult and expensive, loose filters would be best for filtering gases containing much dust. Gases containing little dust may be cleaned with tightly packed filters to obtain higher efficiency. For either type of filter, precleaning with cyclone separators or other means is advisable.

Jan 1, 1960

By William A. Stickney

The zirconium-hafnium separation plant at Albany, Oreg., was the result of a chain of events that started with studies by A. R. Kaufmann at the Massachusetts Institute of Technology. Variations in the listed neutron-absorption cross-section of zirconium caused him to suspect a misprint. As a result of these discrepancies and following his suggestions, Oak Ridge scientists made studies establishing a value of 0.4 barn or lower. This meant that the potential of zirconium for reactor application was greatly enhanced. Since hafnium is invariably associated with zirconium and has a high neutron cross-section, it was necessary that an efficient hafnium-separation method be developed before the superiority of zirconium as a structural material in nuclear reactors could be realized. The Albany plant was built and operated for the Atomic Energy Commission (AEC) under Letter Agreement AT-(11-1) -140, patterned after a plant operated by the Carbide and Carbon Chemicals Corp. at Oak Ridge, Tenn. Construction was begun in April 1951. Hafnium was to be extracted preferentially as hafnium thiocyanate from an aqueous mixture of zirconyl and hafnyl chlorides in hexone (methyl isobutyl ketone) by a liquid-liquid countercurrent system.

Jan 1, 1959

By James Westfield

Bureau of Mines activities for safety and health in the mineral industries were reorganized during the fiscal year to provide direct supervision by the Assistant Director -Health and Safety. On December 19, 1954, the field offices conducting these activities were designated as district health and safety offices reporting to the Assistant Director. The functions of determining the causes of accidents and injuries in the mineral industries and recommending measures to eliminate them were continued, with satisfactory results in improved safety records. The inspection of coal mines and enforcement of the Federal Coal Mine Safety Act of 1952 were conducted as directed by the Congress, and safety conditions in the mines were notably improved. One coal-mine explosion classed as a major disaster occurred during the year. The causes of that explosion and means for preventing a recurrence were still under investigation because of the extreme difficulty in recovering several portions of the mine. Basic research on the nature of certain hazards and ways of eliminating them is continued. Training of individual workmen and supervisors in this knowledge is a major part of the work.

Jan 1, 1956

By David C. Uhrin

Two improved methods have been developed to transfer microfilmed mine maps to suitable base maps showing surface features. The methods provide for (1) positioning and orienting maps; (2) merging adjacent maps; and (3) plotting maps at a common scale. One method produces an overlay mosaic of mine maps using an Integrated camera-processor. This photographic method shows the details of mine workings and is most useful for specific limited-area projects. In the second method, outlines of mine maps are digitized, manipulated, and plotted as overlays using a computer. This computer method can plot mine outlines and spatially index large numbers of microfilmed maps. Microfilmed mine maps used in this Bureau of Mines study are on file in the Mine Map Repository of the Eastern Field Operations Center. The base maps are U.S. Geological Survey 7.5-minute topographic maps. The demonstration area is located in the New Kensington East and West quadrangles, Pennsylvania.

Jan 1, 1977

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and SO percent oxygen should be discouraged because such mixtures are violently explosive and have led to fatal accidents.

Jan 1, 1940

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and 80 percent oxygen should be discouraged because such mixtures are violently explosive and have led ,to fatal accidents.

Jan 1, 1940

By D. A. Buckingham

Engineering and economic evaluations were performed by the Bureau of Mines on 14 Frasch sulfur, 1 native sulfur, and 21 metal sulfide operations in 11 market economy countries. The evaluation included discounted-cash-flow rate-of-return economic analyses at 15 pct to determine the average total cost of production of these two commodities and the potential availability of elemental sulfur (8) and pyrite concentrate. The Bureau evaluated the potential availability of elemental sulfur and pyrite concentrate. Approximately 279 million metric tons (Mmt) of pyrite concentrate at 46 pct 8 is potentially recoverable from 422 Mmt of in situ metal sulfide ore. Nearly 89 pct of the total pyrite concentrate is available at an average total cost of production below the January 1984 pyrite concentrate market price ($43/mt). About 185 Mmt 8 is potentially recoverable from 253 Mmt of in situ elemental sulfur. About 99 pct of this sulfur is available at an average total cost of production below its January 1984 market price ($131/mt).

Jan 1, 1986

By D. J. Bauer

This report covers a phase of an extraction project carried out as part of a research program on rare-earth technology. The current project--the production of pure cerium compounds--is an intermediate step between ore processing and metal reduction. In this connection, a study on a separatory-funne1 scale was made on nonreducing extractants for recovering cerium (IV) from tri-n-butyl phosphate (TBP) and of methods for recovering the cerium nitrate from the strip solution. Dilute sulfuric acid was found to be 100 percent effective in stripping cerium (IV). Several precipitants were effective in recovering the cerium from the strip solution, and ethanol was especially promising. A scaled-up investigation was made into the use of spray-tower type equipment to perform the function of extracting, washing, and stripping. This equipment, referred to as the pressure-bubbler, utilized the system developed on the separatory-funnel scale. Feed solutions were prepared from a bastnasite concentrate by two techniques. Of these, the sulfated bastnasite solution was most successful, resulting in 86-percent recovery of the cerium at 99.7+-percent purity.

Jan 1, 1959

By George N. Aul

This report describes a method developed by the Bureau of Mines for sealing horizontal degasification holes so that they do not create a gas explosion hazard when intercepted by mining. A cement slurry is pumped into the hole through an injection pipe that extends to the back of the hole. Pumping continues until the slurry returns through the annulus to the hole collar. The hole is then shut in and the grout allowed to harden. Application of the procedure to six horizontal degasification holes at Eastern Associated Coal Corp.'s Honey Run shaft is discussed.

Jan 1, 1979

By R. T. Artz

Disposal of sewage is an important part of mine sanitation. Improper... handling and.disposing of sewagerare conducive to the spread of disease and often add foul and nauseating odors to the mine air. The diseases spread by unsafe methods of disposing of waste in mines are typhoid fever, cholera, amebic dysentery, hookworm, and other intestinal diseases due to parasites. Sanitary toilet facilities, with a good sewage-disposal system, each maintained in good order at all times, should help to prevent the spread of diseases transmitted by intestinal body wastos. The metal and nonmetal-mining industries have recognized the impor-dma tance and need for disposing sewage properly; accordingly, facilities of some sort are installed and need today in most large mines. The coal-mining industry has given little thought to the disposal of sewage underground; however, in most mines of the anthracite industry, the inflow of large vol- unes of highly acid mine water and the extensive drainage system required to remove this water provide a natural means for disposing of sewage.

Dec 1, 1946

By Raymond M. Stateham

Microseismic noise rates and slope movements were measured in an unstable area along the north wall of the Tripp-Veteran pit, Kennecott Copper Corp., Ruth, Nev. Low-noise, wide-band microseismic geophones were located at various points in the wall, and the change in distance across open fractures, resulting from instability, was determined by repeated measurements between fixed points set on each side of the fractures. The microseismic noise rate increased and decreased with corresponding increases and decreases in the rate at which the fractures opened. The microseismic noise rates and changes in width of the fractures show excellent agreement, and the two types of measurements complement each other in monitoring the progress of pit wall failure.

Jan 1, 1971

By L. C. IlsLey

The first thing to consider in prevention of electric shock is the voltage of the circuit. No person can be sure that he will not be killed, even from a 110-volt circuit, if he makes proper contact with the circuit so as to cause the maximum current to pass through his body. As the voltage is increased to 250 volts, 500 volts, or 2,300 volts the danger from contact with the electric circuit is increased, Alternating current of the same nominal voltage is possibly more dangerous than direct current. Experience has taught us that both will cause death, and that if the fatalities from this source are to be kept low, certain precautions in the guarding of circuits must be observed.

Feb 1, 1929

By Frank D. Lamb

"INTRODUCTION The use of beryllium and its alloys has come into prominence in the last 15 years and increased considerably during the war. In contrast to other light metals, such as aluminum and magnesium, beryllium is relatively hard, has a high melting point (1,285° C.), and other properties that make it resemble steel in many respects. It has a specific gravity of 1.85, is only slightly heavier than magnesium (specific gravity 1.74), and is appreciably lighter than aluminum (specific gravity 2.7). Its lack of ductility prevents its use as a structural material, but this difficulty may be overcome in the future by the use of various alloy forms. The only important commercial alloy in which beryllium is used today is with copper. The addition of small percentages (1/2 to 2 percent) of beryllium to copper imparts properties to the alloy that make it desirable for use in springs carrying electrical current, particularly at high temperature. Many other uses of berylliam are known, and new uses are being found constantly that make the metal of increasing interest.Possibly the main factor preventing the use of more beryllium is the lack of a large source of beryllium ore. Many beryllium minerals are found as minor constituents of natural deposits, some of the more common ones being beryl (Be3Al2(Si03)6), chrysoheryl (Be A1204), helvite (3(Mn, Fe) Be Si04. MnS), and phenacite (Be2Si04). Of the known beryllium minerals, beryl is by far the most common and has been found distributed rather widely throughout the world. It usually occurs associated with granitic rocks and is commonly found as a constituent of granitic pegmatite."

Mar 1, 1947

By J. D. Ramsdell

The purpose of this investigation was to determine the effects of the impurities, oxygen, nitrogen, carbon, and iron (in low percentages) on the mechanical properties of electrolytic titanium. The strength and hardness of binary Ti-O, Ti-N, and Ti-C alloys are linear functions of alloy content in the composition range investigated. Compared to oxygen and carbon, nitro-gen is the most effective strengthener and hardener, followed by oxygen, then carbon. When the carbon concentration is above 0.10 percent, carbides are present, and strength and hardness are relatively unchanged. For equivalent hardness levels, Ti-Fe alloys are stronger than binary titanium alloys containing oxygen, nitrogen, or carbon. However, the strengthening is related to the presence of transformed beta in the structure.

Jan 1, 1960

By L. J. Kane

While analyzing synthesis gas produced from coal, the Bureau of Mines found that conventional procedures for naphthalene determination were difficult and time consuming. The Bureau developed a rapid and sensitive turbidimetric procedure, which requires only simple instruments and hence can be used in plant-control laboratories. The gas is passed through a saturated aqueous solution of picric acid at 3° to 4° C. whose turbidity is then measured at room temperature. A dispersing agent is added to prevent coagulation of the suspension on warming. Only about 1 mg. (0.015 grain) of naphthalene need be absorbed, and precision and sensitivity are a few ten-thousandths of a grain, or a few hundredths of a grain per 100 cubic feet. The determination can be completed less than 10 minutes after absorption. INTRODUCTION One of the functions of the Branch of Coal Gasification, Bureau of Mines, Morgantown, W. Va., is to develop economical methods for manufacturing, from coal, a mixture of hydrogen and carbon monoxide for producing hydrogen, methane, and other gaseous fuels. This raw gas may contain many impurities, including naphthalene. This impurity is usually determined by first forming naphthalene picrate in a water solution of picric acid, separating the picrate, and titrating the unreacted picric acid or the picrate itself.

Jan 1, 1957