Search Documents

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 39,420 acres of the 60,960-acre Skedaddle Wilderness Study Area in order to evaluate its identified mineral resources. There are no known mines or mining operations in the study area. None of the prospects or claims in or within a 1 mile peripheral zone around the study area have recorded production. At least 276 recorded lode, 6 unrecorded lode, and 29 placer claims have been located in and within about 1 mile of the study area. Approximately 191 of the claims are in the study area. Four of these were current in 1985; all four are wholly or partly inside the study area. None of the study area was being explored by private industry in 1985. Metallic and nonmetallic commodities present in the study area consist of gold, mercury, perlite, basalt, pozzolan, stone, and sand and gravel. Perlite is represented by a single deposit which contains 184,000 tons of subeconomic resources in and adjacent to the study area. No other sites contained identified resources. There are no other identified nonmetallic resources in the study area. Occurrences in and near the study area contain small amounts of gold and mercury in vein-type deposits and show characteristics similar to bulk-tonnage, low-grade gold deposits. No base-metal resources were identified. The gold and mercury mineralization and perlite deposit are spatially related to a volcanic center located in the Skedaddle Mountains. Prospects in the Skedaddle Mountains may contain both precious metals and perlite resources, but additional work is required to adequately delineate these areas.

Jan 1, 1987

This chapter analyses the parameters influencing initial design of communication systems, for new mines and upgrading existing systems. Paragraph 5.2 outlines those variables that must be taken into account during the design stages of a new wired phone system. Recommended features, general requirements, and how they can be implemented are treated in this section. Paragraph 5.3 describes ways of improving or extending the range of trolley carrier phone systems and pager phone systems already installed in the mine. 5.2 New Phone System Design The task of designing an adequate communication, control, and monitoring system for an underground mine must be addressed on a system basis. In addition to insuring that effective voice communication is established, any new system should take into account present and future requirements of remote control and monitoring functions. Chapter 4 illustrated the drastic savings in response time that can be realized when remote control and monitoring are integrated into the overall communication system. The importance of including control and monitoring in the overall design plan for any system cannot be overemphasized. Because each mine is unique, and thus usually has its own special operating characteristics and communication requirements, there is no such thing as "the one best system" to meet the requirements of all mines. The optimum communication, control, and monitoring system for a mine must be one that has been tailored to meet the special requirements of that particular mine. Factors that must be considered during system design include- a. Type of mine and mining methods (low- or high-seam coal, deep hardrock mine, stope caving, longwall, room and pillar, etc.). b. Maximum number of working sections. c. Expected mine growth rate and eventual maximum size. d. Haulage methods (tracked trolley, diesel, belt, etc.). e. Underground power distribution system (dc, ac, or both). f. Features desired (two-way radio paging, private line capability for emergency use, etc.). g. Redundant or backup systems for use during outages of the normal system. Although no two mines are alike, the following items have been established as the main characteristics desired for any underground communication system: 1. Multiple Communication Paths to Outside--the objective here is to give all telephones a second method of communicating with the surface. 2. Audible Emergency Signaling--the communication system provides the main means of alerting miners during emergencies. The system should include means to broadcast distinct audible signals for emergency signaling. Initiation of these signals should probably be controlled from. a central outside point, such as a surface control room. 3. Emergency Override--provisions should be included to permit any conversation to be overridden with emergency communication. 4. Selective Area Page--as mines grow larger it is apparent that the entire telephone system paging mode need not be activated each time a call is initiated. When the general area of a

Jan 1, 1984

By Launa G. Mallett, Kathleen Kowalski-Trakofler, Robert H. Peters, Charles PH. D. Vaught, Peter Keating, William J. Wiehagen

On-the-job training is a common means of training or retraining workers and the practice may seem simple and straightforward. Doing it effectively however requires more thought and preparation than simply having someone follow an experienced worker around and watch what they're doing. Over the years, various techniques and practices have evolved that pass on the skills and knowledge of a trainer or coach in a manner that leads an inexperienced trainee to really absorb the information being taught. On-the-job training thus becomes less a haphazard show-and-tell and more a real transfer of information. The goal of this document is to describe how to develop or manage an on-the-job training program so that information is passed on from trainer/coach to trainee efficiently and effectively. By efficient is meant the best use of time and resources of all those involved in the training process, and by effective is meant that the trainee truly learns the skills and internalizes the knowledge needed to perform the job well. The first part of the document discusses topics to think about when developing a formal on- the-job training program. A structure based on coaching is suggested. Then a workshop designed to prepare trainers as coaches is described. Workshop materials include an instructor’s guide and trainee workbook. These materials can be used to train coaches and to assist trainees as they go through the learning process. Content related to specific jobs can be added to these materials to create targeted on-the job-training manuals. Structuring a formal on-the-job training program It is likely that some form of on-the-job training (OJT) is being conducted at your workplace. The formality of that training can range from a structured program to an informal “follow Joe around” method. If your program is completely unstructured, it may not be meeting current training needs. Worse, it may perpetuate bad habits and create “trained” employees who are not given the same information or evaluated to the same standards. Wiehagen et al. comment that, “Success in using unplanned OJT is usually dependent on the luck of the draw, that is, whether the informal trainer is competent at the task he or she is teaching, is motivated to teach, can organize the job into logical components, and knows something about good practices in teaching and evaluating” (2002, p. 27). It is only through planning a structured OJT program that consistency can be created and maintained. At the least, all trainees who have successfully completed such a program can be expected to perform at an established level—they will know what they must do to be successful.

Jan 7, 2005

By David K. Ingram

The Bureau of Mines conducted underground mapping and rock strength tests to describe and analyze mine roof conditions surrounding ancient stream channel deposits (paleochannels) in the Pittsburgh Coalbed in southwestern Pennsylvania. Paleochannels in the study mine consist of sandstone and/or siltstone and affect the Pittsburgh Coalbed through erosion and/or differential compaction. Differentially compacted sediments within and adjacent to channel deposits caused slip planes, faults, clay-dike faults, clastic dikes (clay veins), coalbed rolls, and slumped structures. Paleochannels can be predicted by recognizing these features and associated sediments, which allows for modification of long-and short-term mine planning and development. Mine entries located beneath the paleochannel deposits exhibit less stable roof conditions than entries with normal (nonchannel) roof. Paleochannel deposits comprise only one-fourth of the mapped study area; however, they contain one-half of the hazardous roof. This study deter-mined that rock strength evaluations, including rock quality designation (RQD), unconfined uniaxial compressive strength testing, and point-load testing, must be accompanied by underground observations. Suggested remedial support techniques include angled and/or longer tensioned bolts, steel mats or crossbars, steel sets or cribbing, and roof trusses.

Jan 1, 1987

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982

By Edward J. Caldwell

In 1930 the Bureau of Mines published a description3/ f the concentrating process of the Magma Copper Co. as it had been developed to that time and was then employed. The prevent paper revises the description to the end of 1943 and includes a description of the smelting processes. Data from the mild and smelter operations for, 1942 are given in tables 1 to 14, Billing costs are included, but it is not permissible to publish smelter costs.

Jan 1, 1944

By John E. Trombly

System objectives and design criteria for an in-mine ULF radio paging system are discussed Coding formats, frequency and bandwidth selection criteria leading to the system design are discussed. The prototype call alert transmitter and pocket page receiver is functionally described. The report includes circuit descriptions, schematics, parts lists, printed circuit fabrication and assembly drawings. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 2011

By Ned Baker

Details are given of a fuel-induction system for a hydrogen, fueled engine. The induction system was designed to preclude backfire otherwise common in hydrogen fueled engines. System features and test data are presented and discussed in the context of the requirements peculiar to use in an underground mine environment. The fuel induction-system when tested in conjunction with a modified Caterpillar 3304 engine provided backfire free engine operation and satisfactory engine performance.

Jan 1, 1982

By G. L. Oldwright, F. K. Shelton, W. E. Keck

"INTRODUCTION Zinc must be of high grade to satisfy the present demand. Even when the amount of premium paid is small, the purer metal as the buyers' preference. The following specifications for spelter were taken from the American Society for Testing Materials for 1927, Part I, pane 524. (The specifications for 1930, p. 582, are tile same.)Another specification for zinc of a much higher grade than any of the above has been established lately by the same society. The committee on zinc die-casting (Proc. Am. Soc. Test. Mat., vol. 31, 1931, p. 263) reached the following, conclusions: I. ""That the purest of zinc is necessary to produce stable zinc-base die castings, and as a result requested specifications for zinc spelter .with total impurities not over 0.02 percent."" Their tests showed that the die castings made of the purest zinc had the least elongation and the greatest tensile strength, and exhibited the least changes with temperature.Still more far-reaching claims are made for the properties of zinc containing over 99.99 percent metal. Zinc foil, for instance, may someday be made as a common commercial product. It would seem likely that the demand for zinc of high grades rill continue and that even purer varieties may be desired. This demand fits in with the modern trend in manufacturing plants of reducing the number of variables to a minimum by using pure materials, and of controlling the processing of metals during their various stages of fabrication by mechanical means instead of by expert laborers."

Jun 1, 1933

By J. L. Holman

The Bureau of Mines, at its Rolla Metallurgy Research Center, has devised methods for separating and reusing the major portion of waste plastics discarded in urban and industrial refuse. Waste plastic concentrates from a local collection drive, recycling center collections, urban refuse pilot plants, and the secondary metals industry were separated into three major thermoplastic families--polyolefins, styrenes, and vinyls--based on differences in density using a Bureau-designed sink-float-elutriation hydraulic separator. Other separation methods and systems such as air classification, jigging, liquid media, screening, and electrostatics were studied. Vinyl plastics contain up to 50 percent HC1. It was found that over 90 percent of the HC1 in vinyls can be recovered as usable hydrochloric acid by pyrolysis at 350° C. The remaining pyrolysis products which had heats of combustion in excess of 12,000 Btu/lb, could become valuable as a future source of energy. A characterization study conducted on eight chopped wire insulation wastes from secondary copper and aluminum processors showed that most wastes contained 2 to 7 percent residual metal and large percentages of vinyl. The residual metal content of some of these wastes was lowered to 0.1 percent and the vinyl portion segregated using various separation techniques. The research also suggests ways in which reclaimed thermoplastics may be fabricated into useful products.

Jan 1, 1974

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

By Maurice C. Fuerstenau

The kinetics of leaching galena with ferric chloride and ferric nitrate have been examined as a function of ferric concentration, salt concentration, temperature and particle size. Diffusivity of ferric complex ions was also established as a function of ferric chloride concentration and temperature. In the presence of 3 M NaCl, leaching rate is controlled by product layer diffusion when ferric chloride is added as oxidant. With NaCl concentrations less than 3 mole/liter rate decreases with decreased NaCl concentration, and, thus, rate is apparently not controlled by product layer diffusion. It is suggested that rate is controlled by lead chloride solubility at the reaction interface under these conditions. When ferric nitrate is added as oxidant, leaching rate is limited by chemical reaction control. An electrochemical model is presented. Activation energies are 8.1 and 11.3 kcal/mol in the ferric chloride and ferric nitrate systems, respectively.

Jan 1, 1984

By S. H. Ash

California leads the Nation in the number of operating metal mines and the small number of persons employed at individual mines, which reached a minimum irk 1932 with an average of seven men. The mines are scattered over the entire State, which is the second largest in area (155,562 square miles) in the United States. The mines are situated at various altitudes, with portals ranging from approximately 300 feet below sea level to almost 12,000 feet above. Many of the mines can be reached only during the summer, while at others the heat of the regions adds so the difficulties during the summer months Supplied of explosives the use (or, probably more correctly, the misuse) of which constitutes one of California's gravest mining problems; are handled and stored under condition that contribute many hazards. The problem of providing medical care is serious and complicated, especially at small mines and more particularly in the almost inaccessible mountainous regions; instances in which a knowledge of first aid would have been beneficial but was lacking, or when first aid was instrumental in saving life or limb because it was available are too numerous to be mentioned.

Jan 1, 1936

By T. C. Green

A two-phase program evaluated commercial proximity warning devices and then served to design and develop an automatic electrostatic field strength measurement device with improved performance. The Phase I program consisted of test and evaluation of three commercial proximity warning devices, all of which operate on the principle of electrostatic field intensity measurement for determining proximity to high voltage power lines. Performance testing of these devices utilized full-scale cranes and power line systems and a scale model facility. The evaluation results were reported in the Phase I report entitled "Evaluation of Proximity Warning Devices" dated 22 February 1980. Under the Phase II program, a microproressor-based data acquisition system was designed and developed to collect and measure field strength at distributed points around the crane boom. This unit (referred to as the Distributed Sensor AC Electrometer) measures the field strength about a crane boom using 17 distributed sensors. Keyboard control is provided for the equipment operator. Measured field strength values are displayed on a line printer and recorded on magnetic tape. Laboratory testing of this unit demonstrated performance characteristics and field strength measurement accuracy within the design goals. A Phase III measurements program is proposed using the AC Electrometer to map the field strength contours about power line configurations.

Jan 1, 1981

By B. W. Madsen

To help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines developed a mathematical model that describes acidic ferric sulfate leaching of copper from sulfide ores. The leaching model can aid in maximizing minerals and metals recovery from primary sources by giving operators and management a better understanding of the copper leaching process. This will aid in improving dump leaching operations. The model is based on a steady-state approximation of the continuity equation for diffusion of ferric ions in the rock pores and the intrinsic leaching kinetics of the various sulfide mineral particles. Ore characteristics included in the model were ore particle-size distribution, particle shape, grade, mineral content, mineral particle size, porosity, and tortuosity. The continuity equation was used with ferric ion concentration gradients and a fixed value for the diffusion coefficient. Except for effective diffusivity, each of these factors was either measured experimentally or estimated from theoretical considerations. The effective diffusivities were determined by fitting calculated leaching curves with experimental leaching data. Vertical variations in leach solution composition and temperature within a dump are not considered in this model. The model accurately predicted copper extractions for several large-scale tests during nearly 500 days of leaching.

Jan 1, 1981

By Seth C. Schaefer

The Bureau of Mines has determined the standard Gibbs energies (AGf°) of CoS1.035 (cobalt sulfide) and Ni2.515S2 (nickel sulfide) with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, CoS1.035, CoO, S02(g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt, with the overall cell reaction C0S1.035(c) + 1.535 02(g, 0.0114 atm) = CoO(c) + 1.035 S02(g)¬ These results, combined with the best available data for ?Gf° of CoO and S02 from the literature, give the standard Gibbs energy of formation of CoS1.035 for the reaction Co(c) + 0 5175 S2(g) = CoS1.035(c) ?Gf° = -38.890 + 18.87 x 10-3T ± 0.185 kcal/mole (866.0 - 1,104.9 K), where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, N12.515S2, NiO, S02(g, 1 atm)//Zr02//02(g, 0.0122 atm), Pt, with the overall cell reaction Ni2.515S2(c) + 3.2575 02(g, 0.0122 atm) = 2.515 NiO(c) + 2 S02(g). Combination of these results with data for ?Gfo of NiO and S02 from the literature yields the standard Gibbs energy of formation of Ni2.515S2 for the reaction 2.515 Ni(c) + S2(g) = Ni2.S1SS2(c) ?Gf° -65.377 + 24.67 x 10-3T ± 0.541 kcal/mole (968.6 -1,053.7 K).

Jan 1, 1981

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $20,799,800 for the 1 .06- million-ton-per-year (MM tpy) mine to $84,027,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $32,506,800 to $1 22,983,500 for the same mines. Corresponding selling prices for the coal range from $12.87 to $11.64 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1976

By H. L. Riley, B. W. Gandrud

"INTRODUCTION AND SUMMARYIn connection with a program of research work on coal at its Southern Experiment Station, the Bureau of Mines, in cooperation with the University of Alabama, conducts washability studies of samples of coal from coal fields in Alabama and other Southern States in which commercially important deposits of coal occur. The first such study on coal from a bed in the Arkansas field has been completed, and the results are presented in this report.One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation's limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield a good grade of coking coal with a minimum of losses of coal in the rejects.The coal on which this report is based was obtained by underground and tipple sampling at the quality mine of the Quality Excelsior Coal Co. about 3 miles east of Hackett, Ark. This mine operates in the Upper Hartshorne bed, which, as the main source of coal in what is known as the Hackett-Excelsior district, yields an excellent grade of low-volatile coking coal, which is marketed at steel plants in Colorado and California. Production from this bed by the major producers in the Hackett Excelsior district was at the rate of about 125,760 tons annually in 1949, according to the Keystone Coal Buyers Manual. 2/In the laboratory, the tipple sample was crushed to 6-inch top size and screened on a 2-inch round-hole screen. The 2-inch to 0 undersize, amounting to 71.4 percent of the total sample, was fractionated into a series of screen sizes and float-and-sink products to get data for determining the washability characteristics of the coal. Before the screening and float-and-sink tests were made, however, machine cuttings, which are now gobbed underground, were added to the 2-inch to 0 sample. Enough of these cuttings were added so that the resulting mixture was considered representative of what the 2-inch to 0 run-of-mine coal would be if all machine cuttings, including the part now being gobbed, were brought to the tipple as a part of the run-of-mine coal.The mixture obtained referred to in this report as the run-of-mine or raw coal."

Mar 1, 1953

By S. R. Crane

One Bureau of Mines goal is to minimize the undesirable environmental impacts associated with industrial plants emitting waste gases containing S02. To help meet this goal, a regenerable flue gas desulfurization process was developed. This process, known as the citrate process, uses a buffered weak acid solution to absorb S02 from the waste gas. The absorbed S02 is reacted with H2S to precipitate elemental sulfur and regenerate the solution for recycle. The H2S feedstock for the process, if not otherwise available, may be produced by reacting two-thirds of the recovered elemental sulfur with natural gas and steam. Laboratory investigations and pilot plant operations were conducted by the Bureau to determine if H2S from the natural gas, sulfur, and steam reaction was suitable for the citrate process. The laboratory investigations, in which an H2S generator was integrated with other citrate process operations, provided a basis for design and operation of the pilot plant. The objective of the pilot plant was primarily to provide H2S for the citrate pro-cess pilot plant at the Bunker Hill Co. lead smelter in Kellogg, Idaho. The design capacity of the pilot plant was 0.4 to 1.25 tons of H2S per day. The operation demonstrated that (1) a 77-to 79-dry-volume-percent H2S product could be produced from pilot-plant product sulfur, natural gas, and steam; (2) the product R2S regenerated the SO2-loaded citrate solution; and (3) under certain conditions over 95 percent of the natural gas could be converted to H2S.

Jan 1, 1981

By O. C. Blade

[In its general study of crude petroleum, tic Bureau of Mines has published several reports that include analyses of samples of crude petroleum from Oklahoma fields3/. This report discusses briefly the properties of crude oil samples collects in come of the producing fields in the State ACKNOWLEDGMENTS This investigation was conducted by the Bureau of Mines in cooperation with the State of Oklahoma. No study was made under the general supervision of R. A Cattell, chief engineer, petroleum and Natural-Gas Division, Bureau of Mines Washington, D. C., and N. A. C. Smith, supervising engineer, Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt senior petroleum engineer Bureau of Mines, Bartlesville, Okla.]

Jan 1, 1939