Search Documents

By James W. Townsend, William H. King

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Alisman, chief, Salt Lake City Division, Mining Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon ore such technique.The Wright borehole-surveying instrument developed at the Homestake mine, Lead, S. Dak., has been described in several publications. 3/ For the benefit of those to whom the publications are not available, the instrument is described here. However, this article will be concerned mainly with the technique developed by the Federal Bureau of Mines for using the instrument.In the use of the Wright borehole-surveying instrument, it was found advantageous to develop a standard practice of operation covering type of film, preparation and care of film, loading film in instrument, placing instrument in container, exposure time, unloading film from instrument, development of film, and determination of dip and strike from film impressions."

May 1, 1947

By J. G. Donaldson

Cobalt-tungsten binary deposits were formed in laboratory experiments by hydrogen reduction of the anhydrous mixed vapors of cobaltous chloride and tungsten hexachloride. The materials were sublimed in seperately heated zones of reaction tube and were transported in a stream of purified helium into the deposition section of the tube where the chloride gases were reduced to metal by a countercurrent flow of hydrogen. Heattreating of the near stoichiometric binary metallic deposits converted nearly all to the intermetallic compound Co3W, however, small quantities of both cobalt and tungsten remained. Mechanical tests showed that the tensile strength of heat-treated 75 percent cobalt-25 percent tungsten deposits was twice as high as that of similarly treated deposits of cobalt.

Jan 1, 1965

By R. O. Dannenberg

This report describes aperiments by the Bureau of Mines and reviews theoretical aspects of the use of organophosphate solvent extraction for recovering beryllium from sulfate leach liquors. The leach liquors were prepared by sulfuric acid leaching of lime-sintered low-tenor beryl flotation concentrates. The experimental work on sulfate leach liquors showed that the acidic esters of organophosphates extracted beryllium slowly but in preference to aluminum. Three common alkylphosphoric acids, di- (2-ethylhexyl) (EHPA), heptadecyl (HDPA), and dodecyl (DDPA), in order of decrmsing selectivity, yielded a partial separation of beryllium from aluminum.

Jan 1, 1962

By Stanton L. Tainter

"As an adjunct to its minerals-investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the supervision of J. H. Hedges, chief, Tucson Branch Mining Division, and under the general supervision of Lowell B. Moon, chief, Mining Division, reports upon certain methods devised to overcome difficulties encountered in cementing of diamond-drill holes at a Bureau of Mines project at Christmas, Gila County, Ariz.Pressure grouting was employed to recondition a caved hole it was desired to reopen and deepen. The hole, which had boon stopped 7 months previously at a depth of 488 feet, was caved below 449 feet in a contact zone of claylike, altered diorite and crumbly metamorphosed limestone. As other means of obtaining moderate pressure were not available, carbon dioxide gas, drawn from tank of liquid carbon dioxide through a pressure reducing and regulating valve, was used. The hole was reopened successfully with 12 grouting jobs.Another hole, where cawing from several water-bearing fractures between 202 and 232 feet gave trouble, was successfully cemented by the use of a grouting plug. An attempt to cement through the rods had failed, owing probably to agitation caused by water currents. Pressure grouting through the caning set above the cave could not be need, because water was forced up outside the casing when pressure was applied. The problem was solved by using a wooden plug 1-13/16 inches in diameter, which, when soaked in water, expanded to a tight fit in an AX hole. A hole was drilled through the plug, and a rubber flap valve was nailed to the lower end. In the upper end of the plug the hole was enlarged to fit loosely over an EX rod coupling finished smooth. The plug was lowered on the end of the drill rods to a point about 10 feet above the cave, where it was allowed to expand tightly to the hole. Cement grout was then pumped through the rods, and the rods were removed from the hole. After allowing time for the cement to set, the wooden plug was chopped out and drilling van resumed.Over 300 tests were made to determine the type of cement most suitable for use on the Christmas job, and the effect of cement-water ratio, temperature, and various admixtures on workability, setting time, and strength. The results of these tests, described in detail in the body of this report, indicate the desirability of thoroughly testing available cements when it is necessary to drill holes under difficult conditions that may cause failure.When it became desirable to reopen and deepen a caved drill hole, it was considered easiest to recondition the hole by pressure grouting, As other mans for obtaining moderate pressure were not available, a method utilizing carbon dioxide gas was employed. The hole was reconditioned successfully with 12 grouting jobs."

Nov 1, 1949

By Charles R. Harrison

The purpose of this study and resulting development of the training program, "Safety--Let's Make It Happen" was to determine the relation of concepts to the development of desired Health and Safety behavior. After extensive pre-contract study, it was hypothesized that improved acceptance and understanding of the Federal Coal Mine Health and Safety Act of 1969 could possibly contribute to the reduction of accidents. Second, in order for an individual to accept and understand the Act, he or she must have a working knowledge of its purposes and application. Third, acceptance and understanding of the Act, necessary to protect the individual from negligence, was imperative. Fourth, an actual operating company could provide the base in which to test these hypotheses in a meaningful manner and develop this type of training program. Six assumptions were agreed upon before embarking on this study and training program development. (1) In the cognitive process, a concept introduction into an individual's personality may result in a behavior quite different than if he or she had been exposed to a different concept.

Jan 1, 1977

By Ellis S. Hertzog

The data published in this retort cover only one phase of a special study of tile physical and chemical properties s of only Alabama coals made by the Bureau of Mines. In addition to determinations of friability, the survey included determinations of grindability, B.t.u. value, and ash-fusion temperature. Assay distillation tests, both for high- and low-temperature carbonization, and proximate and ultimate analyses were made also. However, this preliminary paper is concerned only with the results of friability tests and is issued to expedite the release of this information to the public. The friability, test measures the liability of a coal to break into smaller pieces when subjected to repeated handling, as occurs in the mining, preparation, and transportation operations. Friability depends on many physical characteristics of the coal that vary not only between different seams but also in the same seam. The laboratory methods of determining friability have been developed to give a practical means of estimating degradation of size. So far as is known to the authors, no data on the friability of Alabama coals have ever been published. This caper makes available for the first time fairly comprehensive3 information on this subject. Because the procedure for the tumbler test for determining the friability of coal is relatively new to the coal operators, the authors Lave included a, complete description of it in this report.

Jan 1, 1938

By W. W. Adams

Lower accident rates were the outstanding feature. of the second annual sand and gravel safety competition conducted in 1930 by the United States Bureau of Mines in cooperation with the National Sand and Gravel Association. Both the frequency and, severity rates for accidents were greatly reduced as compared with those shown by the first year's contest, that for 1929. Three times as many plants were enrolled, and the number of man-hours of work represented wad more than doubled. Seventy-six sand-and-gravel plants, situated in 20 States, participated in the competition, as compared with 26 plants, located in 13 States, in the year before. The number of man-hours of employment, which indicated the amount of exposure to occupational hazards, was 4,915,592 an increase of more than 100 per cent over, the previous year's total of 2.259,572 hours. The frequents of accidents declined from 74.4 per million hours for all plants enrolled in the first year's contest to 42.7 per million man-hours for all plants enrolled in 1930. The accident-severity rate was reduced from 9.7 days of disability per thousand man-hours of exposure in 1929 to 5.9 days of disability per thousand man-hours of exposure in 1930.

Jan 1, 1931

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the flow of natural gas through high-pressure pipe lines. This report deals with that part of the study involving the design off pipe-line systems consisting of lines laid parallel to each other. The lines are referred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934

By K. C. Dean

During the investigation of the occurrence of manganese deposits in western United States, the Bureau of Mines collected 2-ton samples from three oxide manganese ores in the Columbia and Elberta Mining Districts, Tooelo and Juab Counties, Utah. To determine the amenability of these ores to standard ore-dressing methods: of concentration, extensive laboratory tests were made. The Wildcat property, one of those sampled, is 7 miles east of Fairfield, Tooele County, Utah. The ore is described as a replacement deposit and occurs along fracture and bedding planes of shale and limestone. Experimental work was done on a sample taken from a stockpile at the mouth of the shaft. The Wildcat manganese ore is intermediate in grade (25.7 percent manganese) and contains clay as the principal gangue constituent. A high-grade product was obtained with high recovery of Manganese by simple washing.

Jan 1, 1949

By John Gross

The modern practice of grinding ores so that often 80 per cent or more of the product is finer than 200 mesh makes it desirable to supplement sieve sizing so as to extend considerably the range of sizing. Moreover, the fact that the material finer than sieve size represents the major part of the work done in grinding emphasizes thick need in can investigation of crushing efficiency. A method based on the settling rate of particles in grater appeared to be most practical for sizing; finely ground ores. There are two possible methods of utilizing this principle: one based on free settling or sedimentation; and the other on separation by means of a rising; current of water, or elutriation. In sedimentation, mechanical entanglement causes material at the start to settle in a mass, and this persists throughout. As this feature is largely eliminated by elutriation, which permits a comparatively clean separation of the various sizes, the elutriation method was adopted.

Jan 1, 1929

By D. S. Kingery

Investigations over several years have disclosed that the principal manners of occurrence of shuttle-car injuries are in order: 1. Victims in contact with roof or crossbars. 2. Victims in contact with ribs or timber legs. 3. Victims falling from, or jerked from, shuttle cars. 4. Victims in contact with overhanging brows or protruding pine for pin timbers, or water lines. 5. Contact with persons or collisions with parked equipment. 6. Victims injured by roof falls or falling timbers caused by knocking out roof supports with shuttle cars. 7. Victims injured by runaway shuttle cars. 8. Victims injured while loading or unloading timbers or other materials from shuttle cars. These recurring types of shuttle-car accidents reflect the physical conditions of the working sections, certain safety deficiencies in shuttle-car maintenance and design, and unsafe practices by operators.

Jan 1, 1952

By David S. Yantek

A-weighted sound levels around vibrating screens in coal preparation plants often exceed 90 dB(A). The National Institute for Occupational Safety and Health (NIOSH) is actively developing noise controls to reduce noise generated by horizontal vibrating screens. A 121-microphone, 3.5-meter-diameter array was used to perform beamforming to determine locations of significant noise radiation on the screen. Below about 1 kHz, the screen body was found to be the most significant noise source. The beamforming contour maps showed several key locations on the sides of the screen and the feedbox are the most significant contributors. Operating deflection shape (ODS) analysis was used to examine the screen behavior under actual operating conditions. This information is helpful in determining how to modify the screen body to reduce the noise radiated by the screen below 1 kHz. The analysis showed modal vibration patterns on the sides and feed box were the main contributors to noise. The results show several areas on the screen sides and feedbox that can be modified to reduce noise.

Jan 1, 2009

By William H. King

The Fannie Ryan deposit is situated about 9 miles northwest of Boulder City, Clark County, Nev. at an altitude of about 2,000 feet on the north side of the River Mountains. The deposit is covered by several unpatented claims owned by Fannie B. Gulick of Las Vegas, Nev. The Boulder City deposit is within the Hoover Dan National Recreational Area. It is situated about 3 miles southeast of Boulder City in sec. 23,T. 23 S., R. 64 E., Clark County, Nev. The Deposit was covered by several unpatented mining claims owned by S. R. Whitehead of Las Vegas. The deposits occur in sedimentary beds of the Muddy Creek formation that overlie older volcanic extrusive. The manganese minerals occur as soft oxides of the wad type. The exploration was conducted by the Bureau of Nines in cooperation with the Federal Geological Survey and comprised a study of the geology, mapping of the areas, and development by shaft sinking; diamond drilling, and sampling. On the Fannie Ryan Gulick property the work consisted of cleaning and sampling seven old trenches on the outcrop and diamond drilling seven holes totaling 1,482 foot. At the Boulder City deposit 188 feet of drilling was done in two holes. A 4- by 6-foot shaft was sunk to a depth of 44.5 feet, and the north and south sides of the shaft were sampled.

Jan 1, 1950

By J. P. Hansen

In order to help assure an adequate domestic supply of minerals essential to the Nation's economy and and security by developing more efficient minerals extraction technologies, the Bureau of Mines Tuscaloosa Research Center examined the application of autogenous microgrinding to calcium carbonate minerals. Treatment of minus 8-mesh Alabama marble resulted in a product 80 pct minus 5 micrometers (µm) at a power consumption of 70 to 80 kwhr/ton, This study shows that coarse particles of calcium carbonate minerals are effective as the grinding media for the autogenous attrition grinding of these minerals. The minus 8- plus 30-mesh fraction is an effective grinding medium (sand) for particles smaller than 30 mesh. A 40-pct-solids slurry and a sand: marble ratio of 2.5 appeared to be near optimum. For residence times above 13 minutes, products were greater than 80 pet minus 5 µm and greater than 54 pct minus 2 µm. Power consumption was uniformly low, ranging from 50 to 100 kwhr/ton of product depending upon the feed rate. One marble sample from Georgia was shown to be the most persistent grinding medium, with losses of less than half those of the other materials tested.

Jan 1, 1980

By Terry L. Muldoon

The Bureau of Mines conducted an investigation to quantify microphone response variations that could result when the microphone is worn by a worker, as with a personal noise dosimeter, and to suggest an optimum placement and orientation of the microphone for noise exposure measurements. Previous studies have shown no significant variations in a diffuse field. This investigation, therefore, was conducted in the free-field conditions of an anechoic chamber using an anthropometric dummy as a subject, and broad band noise as the acoustic stimulus. This investigation established that, in a free field, the wearer's body does significantly affect microphone response; the response variations are a function of azimuth, and location and orientation of the microphone. Results suggest that locating the microphone on top of the subject's shoulder, oriented parallel to the body axis, should yield data comparable to that obtained using a sound-level meter.

Jan 1, 1973

By P. C. Good

To meet a growing need for thorium metal of high purity and amenability to fabrication, the Bureau of Mines devised a method for preparing thorium metal by the reduction of thorium tetrachloride. Thorium tetrachloride was prepared by chlorinating calcined thorium oxalate with carbon tetrachloride. The crude thorium tetrachloride, containing oxygen-bearing compounds, was purified by a double vacuum distillation at 800 to 900° C., and thorium metal was made in the form of a dense sponge by the reaction of metallic sodium or magnesium with thorium tetrachloride at 800° C. Vacuum arc melting was used to consolidate the sponge metal to ingot form for evaluation of its physical and chemical properties.

Jan 1, 1960

By J. William Ganser

This paper is one of a series being prepared by the United States Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1931

By M. B. Shirts

Bench-scale studies were made on a reductive hydrometallurgical procedure to convert chalcopyrite flotation concentrate to copper metal or a readily leachable sulfide. Reductive conversion of chalcopyrite and dissolution of iron and sulfur were accomplished in hydrochloric or sulfuric acid solution by the addition of metallic copper, iron, or lead. Use of metallic copper as the reductant enabled extraction of 95 and 46 percent of the iron and sulfur, respectively. The products were ferrous iron, hydrogen sulfide, and a copper sulfide. Use of metallic iron or lead as the reductant enabled extraction of 95 percent of both the iron and sulfur. The products obtained with metallic iron or lead were ferrous iron, hydrogen sulfide, and metallic copper.

Jan 1, 1974

By W. R. Hardwick

Nuclear explosive fracturing has been suggested as a method to make hard rock amenable to extraction by a modified block-caving method. To evaluate this possibility, conventional and nuclear blasting practices are discussed, underground mining methods for large deposits and their costs are described, and the cost of fracturing ore with a nuclear explosive and subsequent mining by a modified caving system is estimated and compared with both open-stope and block-caving mining costs. While the direct cost of fracturing the ore in hard rock with a nuclear explosive is less than with conventional explosives, additional costs imposed by the use of nuclear explosives may make their use unattractive for deep mining.

Jan 1, 1970

By Otto Ruhl

"INTRODUCTION With the conclusion of the war and the ensuing readjustment of industry to peacetime conditions, the Bureau of Mines recognized that definite and complete figures on the reserves of zinc and lead ores in the Tri-State District would be needed for an evaluation of the problem of reconversion. In October 1945 its engineers began examination of all the mines and pros¬pects in the Tri-State area and assembling of the basic data for a complete detailed estimate of the reserves of the field. Six to twelve months will be required to complete the report with the personnel available; therefore, it has been deemed advisable to provide as much data as possible for imme¬diate use. Accordingly, a confidential report prepared in January 1944 for the use of and in cooperation with the War Production Board has been brought up to date to form the basis of this preliminary estimate of reserves.The 1944 report has been revised by first subtracting from the reserves then set up for each mill group the amounts mined and milled by those properties for 1944 and 10 months of 1945, with November and December estimated. These production statistics were taken from the monthly reports of the Metal Economics Division of the Bureau of Mines. The remaining reserves were then adjusted by additions of tonnages of new reserves disclosed by developments during the years 1944 and 1945. Such additions were based upon the data furnished by various operators, upon estimates supplied by the Federal Geological Survey District Office at Miami, Okla., and upon estimates of the engineers of the Bureau of Mines Joplin field office.It is apparent from the work so far accomplished in the detailed exami¬nations now under way that the final estimate of reserves will probably be somewhat greater and will differ to a certain degree from these preliminary totals, not only as to the tonnages of ere but also as to grades and distribution by areas. This is due to the fact that all the factors of development, exploration, and geology are being considered in the present examination and report for each individual mine and prospect, whereas the previous reports covered only the immediate development factors surrounding each mill group then in active operation or projected for operation at some early date in accordance with the possible needs for war production."

Aug 1, 1946