Search Documents

By Harry E. Tufft

Data were obtained by the writer from a number of the large coul-mine operators in Illinois, on the consumption and cost of timber used in their mines and the quality of the timber now being used as compared with former years. This information supplemented by comparative date for previous years published in bulletins of the filinois Coal Mining Investigation series, and other sources, is presented below. This survey is part of a cooperative study with the . S. Forest Service, of the mine timber situation, with particular regard to the economies to be derived by better selection, preparation, and storage of timber, and especially treatment with preservatives to prolong the life. Geo. S. Rice, chief mining engineer of the J. S. Bureau of Mines, under whose general direction the work was done, gave valuable advice and criticism. R. B. Miller, State Forester, contributed helpful data which he had recent- ly obtained in an independent study of the mine-timber situation in Illinois.

Apr 1, 1923

By Leroy Dockter

The grinding characteristics of lignite in a ball mill were investigated. The variables studied were initial lignite moisture content, degree of in-the-mill drying, and lignite source. The mill tested was a pilot-p1ant-size conical ball mill which had a maximum output of from 80 to 180 lb/hr pulverized product depending on the lignite and test conditions. The capacity of the test mill ranged from 82 to 103 lb/hr depending upon mine source, in pulverization of as-mined lignite with minimum drying, The capabilities of the ball mill could not be correlated to Hardgrove index of the individual lignites or other observed physical properties. Predrying lignite from its 35 to 40 percent raw moisture content to about 10 percent moisture before grinding improved the mill capacity 87 percent, compared to an increase in capacity of 74 percent with in-the-mi11 drying to the same product moisture.

Jan 1, 1967

By R. A. Friedel, J. L. Shultz, A. G. Sharkey

The purpose of this investigation was to study the primary materials associated with the coal structure . Mass spectrometric techniques can be useful in studying the chemical structure of coal and various high- molecularweight materials derived from coal . Investigations of pyrolysis products and extracts of coal , and also whole coal , showed : 1. Aromatic hydrocarbons obtained by the vacuum pyrolysis of coal below 300 ° C possibly were sorbed material rather than decomposition products . 2 . 2 . Thirteen structural types having molecular weights from 78 to 400 were identified in pyridine extracts constituting one - quarter or more of the coal by weight . 3. Material extracted at room temperature with a methanol - benzene solvent and a vacuum pyrolysis condensate obtained at 450 ° C contain similar components . The extract and the condensate have approximately the same average molecular weights ( 200-300 ) . 4. Material extracted from coal at room temperature is altered even by mild thermal treatment . 5. Changes in various alkyl series occurring in thermally treated coal extracts can be followed quantitatively . 6. Similarities in the spectra of coal and graphite were indicated in an investigation using a mass spectrometer equipped with a spark source . Determinations on a coal - ash sample by this technique showed good agreement with data obtained by emission spectroscopy .

Jan 1, 1963

By Manuel Gomez

Prediction models were constructed for seam elevation, overburden, and sodium concentration for a lignite deposit in Ward County; N. Dak. These models were developed by mathematical-statistical techniques using surface coordinates as independent variables to permit interpolation between drill holes. The results suggest that sodium concentration in lignite may be predicted in advance of mining. This information is helpful to mine planning, specifically, in scheduling production to deliver a uniform product to existing powerplants.

Jan 1, 1970

Determine the site specific flow behavior of leachants and groundwater during development, production, and restoration phases of an in situ leaching operation. Approach A computer program has been developed which simulates the hydrologic activity associated with in situ mining. Various user options enable modeling of many of the site specific geologic conditions and well field specifications that affect the hydrology of solution mining. How It Works In situ hydrology is modeled, using a closed-form solution to the three-dimensional, partial differential equation that describes changes in hydraulic head as a result of pumping from leachant Injection and recovery wells. Model capabilities include arbitrary well patterns and pumping schedules, partially penetrating well screens, directionally anisotropic permeability and natural groundwater flow, in either

Jan 1, 1981

By R. V. Higgins

A numerical method is presented to calculate the pressure distribution in a petroleum reservoir that has irregular boundaries. The computer program is straightforward and requires minimal data preparation. The method can also be used to determine pressure distribution in many other types of underground reservoirs. In this method, the grid solution of the fluid-flow equations in a reservoir that has regular boundaries (previously published) was expanded to handle irregular boundaries. The computer program locates grid points at the irregular boundaries. The method of mirror images is then used to form a special stencil to determine the pressure at each of these points. Two examples are presented to demonstrate the applicability of the method for virtually any reservoir configuration.

Jan 1, 1972

By R. Hogg, T. F. Dumm

"A procedure for evaluating the size/specific gravity distribution of ultrafine coal and the distributions of sulfur and ash with respect to particle size and specific gravity is described. The procedure is essentially an extension of the conventional coal washability technique in which special precautions are taken to ensure particle dispersion in the heavy organic liquids, centrifuges are used to obtain adequate separation rates, and micromesh sieves are used for size separation at fine sizes. An example of the application of this technique to the evaluation of the extent of liberation of sulfur and ash in a coal sample ground to 90Z passing 200 mesh (74 um) is described.INTRODUCTIONIn order to determine the potential for deep cleaning of coal by fine grinding to liberate sulfur and ash-forming minerals, it is necessary to obtain data on the distributions of these species by size and specific gravity. In conventional coal processing operations, this information is obtained by means of a standard ""washability"" analysis. Attempts to extend this procedure to ultrafine coal, however, have generally been unsatisfactory and have often led to unreliable and inconsistent results [11. The present authors have described a modified washability procedure in which cumulative specific gravity fractionation is combined with sub-sieve size analysis (by laser diffraction/light scattering) to determine the particle size/specific gravity distribution of ultrafine coal [2]. Unfortunately, because this technique does not involve separation of the individual fractions, only limited information can be obtained on the specific distributions of sulfur and ash.The objective of the work described in this paper was to develop and evaluate a procedure for size and specific gravity fractionation of ultrafine coal and to use conventional analyses for sulfur and ash to determine their relative distribution in the coal. The procedure is essentially a simple extension of the standard washability analysis [3] but incorporating special precautions for treating ultrafine particles.EXPERIMENTAL Material The material used in the development and evaluation of the ultrafine coal fractionation procedure was a medium volatile bituminous coal from the Lower Kittanning seam. A sample of the coal (nominally - 1/4 inch), obtained from the Penn State Coal Data Base, was ground to 90% passing 200 mesh by the following two-stage grinding procedure: About 2 kg of the as-received coal were ground to about 30Z passing 200 mesh in a Model 4-E Quakertown mill (""coffee grinder""). About 1 kg of this product was then ground to about 90Z passing 200 mesh in a Holmes Model 300 Pulverizer."

Jan 1, 1989

By G. S. Scott, W. J. Huff, G. W. Jones, R. E. Kennedy

"INTRODUCTION This report gives preliminary results of field and laboratory investigations made at the request of the War Production Board relative to causes that have occurred during the last 8 months in acetylene-generat72,r plants in shipyards on the Pacific coast.Six acetylene-generator explosions have occurred in four shipyards. These explosions killed five operators, injured six others, and extensive damage to the plants involved and curtailmnent of vital defense Although the occurrence of acetyiene-generator explosions in other section of the United States is not known, it appears, at least, that if such have occurred, they have caused only minor damage and no loss of lives.The use of acetylene in shipyards on the west coast has expanded tremendously during the past 2 years. These shipbuilding, companies erected aletylene-generatcr equipment, which was soon found to be entirely inadequate to meet the needs of their expanding acetylene requirements for welding, cutting, shrinking, and other purposes, and instances found it necessary to operate their equipment at rates greater than deemed consistent with safe operating practice."

May 1, 1944

By W. W. Adams

"Fatal accidents at coal mines throughout the United States killed 234 employees during January 1924, according to reports from State mine inspectors to the Bureau of Mines of the Department of the Interior, Included in the number of fatalities are 68 deaths caused by two explosions during the month, one explosion occurring in a mine at Johnson City, Ill., and causing 32 deaths, and the other in a mine at Shanktown, Pa., and causing 36 deaths. The fatality rate for the month was 3.94 per million tons, based on a production of 59,435,000 tons of coals In January 1923 the fatality rate was 3.52, based on 206 deaths and an output of 58,458,000 tons.Bituminous mines in all States reported 202 fatal accidents, the production being 51,170,000 tons., and the fatality rate being 3.92, as compared with 3.28 for January last year, For the anthracite mines in Pennsylvania, the reports covered 32 fatalities, which, on the month's output of 7,955,000 tons, indicated a fatality rate of 4.02 per million tons, as against 4.89 for January 1923.As compared with January 1923, the reports for January of the present year indicated lower fatality rates per million tons for all of the main causes of accidents except explosions. For falls of roof and coal, the fatality rate per million tons declined from 1.85 in January 1923 to 1,68 in January 1924; for haulage accidents the rate declined from 0.62 to 0.42; for explosives, from 0.19 to 0.12; for electricity, from 0.12 to 0.07. The rate for explosions increased from 0.21 to 1,31 per million tons. -- Reports of Investigations, Department of the Interior, Bureau of Mines."

Feb 1, 1924

By M. D. Aldridge

This document reports the results of a two-year research effort aimed at improving communication systems used in coal mines. This work was conducted under a program whose original goal not only involved the development of practical and effective electronic systems for operational communications, but also for monitoring, at a central location, remote instruments at key positions in a mine. About half way through the originally proposed three year effort, the program was redirected to phase out the communication effort at the end of two years and to concentrate the program" resources on the investigation of new monitoring system concepts developed by this research. Thus, the work reported here is incomplete relative to the originally pro- posed program. However, the work was carried to the point of providing sufficient evidence to aid in the comparison of certain new communication concepts. For the concepts chosen for this study, the work was stopped short of hardware development and field testing, Several reports in the form of Master's theses and a Doctoral Dissertation have resulted from this research. They each report in considerable detail the results of several individual" contributions to this program. In preparing this report, an attempt has been made to provide a complete description of the significant results but with- out burdening the reader with the minute details. These more detailed reports are referenced heavily for the convenience of those interested. PRESENT COMMUNICATION METHODS Two types of communication systems are presently used In coal mines. They are: 1, Various forms of telephone systems, and 2. Carrier current radio systems using the trolley line as the interconnection circuit. Carrier current radio is used almost exclusively for control of rail trafflc by the dispatcher. Almost all other communication uses the telephone system, Telephone lines generally extend to areas where trolley lines are not present such as the outside offices and warehouse. Therefore the telephone system provides the primary means of voice communication. Telephones - Telephone systems employed in American coal mines fall into three categories. 1. Paging type telephone systems - these systems have individual stations which use battery powered transistor audio amplifiers to boost signal levels for normal communication. When in the page mode,

By Robert W. Freedman

This report describes sampling and analytical procedures used for measurement of sulfates in diesel tailpipes and in the diluted exhaust within dilution tunnels. A variety of methods exist for sulfate analysis for such systems, including ion exchange. Two chemical methods used by the Bureau of Mines are described in detail. These are based upon spectrophotometric measurement of chloranilic acid using barium chloranilate. The procedures are rapid and relatively inexpensive. In general, ion exchange is preferred by many analysts for sulfate analysis. However, it is more complex and expensive than chloranilic acid procedures, which are adequate for exhaust analysis.

Jan 1, 1982

By l.J Prosser

from 1990 to 1996, 16 states reported 92 injuries from falls of roof, rib or face in the more than 90 underground stone mines in the United States (Fig. 1). Missouri, Pennsylvania and Kentucky accounted for 48% of the total number of injuries (Fig.2). Of this total, 11 miners were killed. Of the 11 fatalities, 10, or 91 %, were associated with unrecognized loose or failed rock within the roof beam. Additionally, unrecognized roof beam failures resulted in a majority of the falls of ground injuries occurring in underground US stone mines from 1990 to 1996.

By Frank Chase, M. Terry Hoch, George Karabin, Joseph C. Zelanko, Christopher Mark

Pillar recovery continues to be a significant ground control hazard. During the past decade, 10 miners were killed during pillar extraction operations in southern West Virginia. Studies conducted during the past decade have identified a number of “risk factors” that can be used to evaluate pillar extraction plans: •Cut sequence •Final stump •Timber or Mobile Roof Supports •Roof bolting •Intersection span •Depth of cover •Roof quality •Age of workings For each of these factors, rock mechanics science suggests which alternative would be expected to be more risky. For example, numerical models were used to evaluate different cut sequences, and indicated that less roof convergence occurred with the outside lift method than with the Christmas tree in the particular environment simulated. For many of the risk factors, accident statistics confirm the science. One finding was that currently almost 70% of the retreat coal in southern WV is being mined with MRS. In contrast, timber supports were used in 70% of the past decade’s pillaring fatalities. This paper discusses each of the risk factors in turn, presents the relevant accident statistics, and shows how the risk factors can be combined to estimate the overall hazard. It also addresses the use of pillar design to minimize the risk of global stability hazards including squeezes, massive collapses, and bumps.

By George C. Branner

This study was planned to present salient facts of the California and Nevada sulfur industries and to indicate existing opportunities for increased economic utilization of California and Nevada sulfur resources. Numerous publications on sulfur have been issued by the Federal Bureau of Mines, including Information Circular 6329, Sulfur, by Robert H. Ridgway (1930); annual Minerals Yearbook chapters on Sulfur and Pyrites, by various authors; and a chapter on Sulfur by G. W. Josephson in Bureau of Mines Bulletin 556, Mineral Pacts and Problems (1956). This literature, however, deals primarily with the national and international sulfur situation and does not attempt to analyze the possibilities for increased economic development of sulfur resources by individual States. The present study attempts to analyze these possibilities in California and Nevada and to (1) evaluate factors that have influenced production and consumption in California and Nevada and (2) indicate apparent trends in production, consumption, and prices in these States.

Jan 1, 1959

By Stephen P. Signer

This paper presents an overview of laboratory and field tests on approximately 250 fully grouted roof bolts instrumented with strain gauges in order to study loading behavior. Laboratory work included pull tests, time-dependent tests, and shear tests. The field tests were conducted in 14 different mines extracting different commodities. However, because of the focus of this publication, only the results of tests in 9 coal mines are reported here. In the field tests, all but 14 bolts were loaded by rock movement; these 14 bolts were tested using pull gear. The variables studied included anchorage length, mechanical interlock, time-dependent behavior, shear, installation load, loading rate, and maximum load level. Such information will improve the understanding of the behavior of resin-grouted bolts, which in return will enhance the safety of miners by reducing the occurrence of rock falls. The influences of geology, overburden depth, entry width, mining-induced stresses, and bolt spacing are not described.

Jan 10, 2000

By John Nagy

The Bureau of Mines examined explosion development in a closed spherical vessel, mathematically correlating flame travel, pressure, and time with parameters defining the reaction. The model assumes that burnt and unburnt zones are separated by a thin, radially moving flame front. Isothermal and adiabatic systems are considered. Correlation with gas and dust explosion data is better for the adiabatic system, but the isothermal development is simpler and in reasonably good agreement. Interpretation of the explosion phenomena is facilitated by expressing the rate of mole change in the flame front in terms of elementary parameters. This expression is developed by examining the components of spatial-flame velocity.

Jan 1, 1969

By Jr. Watts, J. L. Ambs, B. K. Cantrell, K. L. Rubow

"The University of Minnesota and the U.S. Bureau of Mines collaborated to develop and field test a personal diesel exhaust aerosol sampler (PDEAS). The PDEAS was field tested in five underground coal mines that use continuous miners and a variety of diesel vehicles, including diesel haulage and utility vehicles. One mine was surveyed a second time, with the haulage vehicles fitted with a low-temperature disposable diesel exhaust filter (DDEF). Aerosol samples were collected with a variety of instruments, including the PDEAS and the microorifice, uniform-deposit impactor (MOUDI). This paper presents the diesel exhaust aerosol (DEA) concentration data collected in these mines and assesses the impact of diesel face-haulage equipment, with and without exhaust filters, on underground mine air quality.The average DEA concentration at the haulageway location for five mines, determined by the PDEAS, was 0.89 mg/m3, with a standard deviation of 0.44 mg/m3 • DEA contributed 52 pct, of the respirable aerosol at the haulageway location. Use of the DDEF at one mine reduced DEA by 95 pct, with a standard deviation of 6 pct, and filter life averaged 10 h. DEA contributed a large proportion of the respirable aerosol concentrations in mines with diesel equipment, and a substantial reduction was achieved with use of a DDEF. INTRODUCTIONDiesel equipment is gaining popularity in underground coal mines. There are an estimated 1,951 units of diesel equipment in 152 underground coal mines compared with 1,100 units in 110 mines 5 years ago (J).5 This increased use is due to the recognition that diesel-powered vehicles are more versatile, which can contribute to increased productivity compared with their electrically powered counterparts. Approximately 33 pct of the diesel vehicles haul coal, 45 pct haul personnel and materials, and- 22 pct perform other duties, such as roof bolting, rock dusting, and road maintenance. Most mines using diesel equipment are located in Kentucky, Utah, Virginia, and Colorado."

Mar 1, 1992

By George S. Rice, L. C. IlsLey

"A remarkable explosion of fire-damp caused by a discharge of lightning at the new shaft at the Sitalpur coal mine, has been reported by the Chief Inspector of Mines of India, who gave the following details:""The explosion occurred during a thunderstorm, and the evidence showed that a flash of lightning had, to all appearances, passed down the shaft caus¬ing disruptive discharges at certain points between the guides and the winding rope, rending the latter at two places situated respectively .228 .feet and 278 feet from the surface, The distance between the winding rope and the side of the shaft was 5 feet 4 inches, indicating a spark gap ;of this width, and an intensity of discharge which could not fail to ignite the explosive mixture of gas and air known to be present in the shaft.""The Compressed Air Magazine, January 1920 issue, which contained the above extract also goes on to state;""In 1915, M, Ferey described in a paper read before the Societe de l'Industrie Minerale phenomena of a similar character to the above. In a pit liable to sudden outbursts of gas, for the sake of safety, shot firing was carried out from the surface. During a storm, in the year 1905, shots went off in two places after the detonators had been connected to the conductors) we read in the Colliery Guardian, London. These shots were situated respectively 1,400 and 1,410 metres from the firing station, Realizing the possible danger from this cause, the precaution was taken to cut the conductors at the bottom of the shaft and to connect there just before firing, Even under these conditions a shot went off spontaneously, -.owing, it is believed, to lightning."""

Feb 1, 1920

By Lisa Steiner

Almost every process has a predecessor, and studying the predecessor helps to define needs and shortcomings to be addressed in the new design. It also suggests what information is needed by the users in order for them to be able to operate safely and effectively. The end users of a system can provide important feedback to better evaluate the current and proposed designs. When new technology is introduced into a system, mishaps may occur before it is realized that human-system interactions were not considered adequately in the design process. A systematic methodology to evaluate the causes of these injuries and to develop remedial recommendations can enhance safety. This paper illustrates how such an approach was used to assess remote machine operation in underground coal mines. The dynamic work environment of underground mining with its unpredictable geologic anomalies can result in numerous hazards. Many of these hazards, including mine roof collapse, occur near the working face where coal is being extracted. The face area is also where the most intricate interactions of people and equipment occur. For these reasons, a high priority has been placed upon minimizing hazards to the workers at the face. A remote control operation was introduced to provide a safer working distance from these hazards. As the remote control technology began to be widely used for extended cut mining operations, new issues became evident. It was essential to develop mechanisms for mines to evaluate these issues in order to predict and reduce injuries. Mining methods and equipment changes must allow for the ability of workers to adapt to changes in their dynamic mining environment. Consideration should be given to how the worker will use familiar information to make decisions in now unfamiliar situations. There will be both intended and unintended consequences [Merton, 1949]. Designers try to anticipate and eliminate surprises, but it is impossible to eliminate them all. How, then, will the new system affect the tasks to workers which are currently accustomed? As suggested below, this question may be addressed and more of the unintended outcomes predicted with a planned design process which includes strong human factors input to determine interactions and behaviors of participants.

Jan 1, 2005

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in and above an operating coal mine, McElroy Mine, located near Moundsville, Nest Virginia. The electromagnetic environment created by 300 volt dc and 480 volt ac machinery was measured. In one technique noise was measured over the entire electromagnetic spectrum of interest for brief time periods. The noise was recorded using broadband analog magnetic tape. The noise data was later transformed to give spectral plots. In the other technique, noise amplitudes were recorded at several discrete frequencies for a sufficient length of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974