Search Documents

By M. Kanda, J. W. Adams

A system for measuring amplitude probability distributions (APD’s) of electromagnetic noise in coal mines is described and typical APD’s from an underground coal mine are presented. The APD is a basic statistic required for the design and analysis of communication systems, especially those intended for use in noisy environments, and where neither overdesign nor underdesign is acceptable. The rms and average field strengths are obtained by integration of the APD, and examples are shown at several frequencies. All field strength levels are given in absolute units. Selected frequencies cover the range from 10 kHz to 32 MHz.

Jan 1, 1973

Reduce respirable dust in coal preparation plants. Approach Survey a representative sample of coal preparation plants to (1) determine the dust problem extent, and (2) evaluate practical dust control techniques. Coal Preparation Plant Survey Results Of the approximately 500 coal preparation plants in the United States, 18 plants in six States were randomly selected for survey. The raw hourly capacities ranged from 250 to 1,250 tons, plant construction dates ranged from 1037 to 1982, and usually 3 to 10 workers were required per shift. Respirable dust concentrations within the plants surveyed ranged from very good (less than 1 mg/m') to very poor (14 mg/m3). No relationship was found between dust concentration and age or capacity of the plant. Six of the plants had long-term respirable dust concentrations between 7 and 14 mg/m' in specific areas; six had concentrations between 2.2 and 6.2 mg/m'. Except fur ventilation, only 4 of the 18 plants used operating dust control devices with mixed effectiveness.

Jan 1, 1989

By Will H. Coghill

Titanium is a well-known component of bauxite ores, sometimes occurring in sufficient quantity to mace its recovery worth considering. This question has been raised by some of the companies lixiviating bauxite ores. At the East St. Louis plant of the Aluminum Ore Co., a subsidiary of the Aluminum Co. of America, the waste sludge discharged daily contains over 75,000 pounds of Ti02. The sludge is all through 20-mesh, and a large proportion is slime. A supple of the waste was deslimed so that a gravity-concentration test of the "sand" could be made. The Aluminum Ore Co. cooperated in the work and made the chemical determinations In order to anticipate the results of table concentration a series of specific gravity fractions (float-and-sink) was made with heavy liquids. Acetylene tetrabromide was used for a density of 2.95, methylene iodide for 3.33, and thallium formate for 3.78, and the double salt of thallium formate-malonate made the separation at slimed sample appears in Table 1.

Jan 1, 1928

By John Nagy, Austin R. Cooper

Information is presented on the pressure and rate of pressure development during a dust explosion . The data were obtained in laboratory studies in a 75- cubic inch vessel with mineral , agricultural and chemical dusts . The factors investigated include dust concentration , oxygen concentration of the atmosphere , admixed inert powder , and admixed moisture . Information is given also on the effects of these factors on the composition of the atmosphere after the explosion .

Jan 1, 1964

By D. Harrington

"In at least three out of every four working faces in metal mines there is no attempt made to cause air circulation other than by use of compressed air, and in at least nine cases out of ten the compressed air is released merely by opening, or partly opening, the valve and allowing the compressed air to escape through open air hose used to convey the compressed air to the drilling machines. Usually no blowers are in use during periods of drilling, as the exhaust from the drill provides cool, comparatively fresh air for the driller; however, in some instances, the compressed-air line is provided with a tea connection, which permits taking air for the drill from one side of the tee, and air for ventilation through a separate hose used as a blower, simultaneously with drilling.Table 1 contains temperature and humidity data as to compressed-air blowers from open end of air hose at 36 working places in eleven metal mines of four States, embracing the mining of gold, silver, copper, lead and zinc ores, and at horizons ranging from 500 feet below the surface to as low as 4900 feet.It is noticed that the ordinary air surrounding the worker at the face gives an average wet bulb temperature of 81.7° F. for the 36 working faces, with 84.7° F. dry bulb and 87.2 per cent relative humidity. The average wet bulb tem¬perature of 36 readings at these working faces of compressed air at the end of the,hose as the air issues from the hose was 67.4° F., or 14.3 degrees lower than the average wet bulb readings of the air of the working places; however, the average dry bulb temperature of the 36 readings of compressed air as it issued from the end of the hose was 79.7° F., or only 5 degrees less than that of the general air (84.7°); the relative humidity was 51.1 per cent as against 87.2 per cent for the surrounding air. Readings were taken in five raises, seven crosscuts, ten drifts and 14 stopes.It will be noted that the velocity or movement of the general atmosphere at each of the entire 36 working faces, was found to be practically imperceptible; this might readily be inferred since compressed air is rarely used on blowers if there is adequate circulation of the general air of the place. Where rook temperatures could be obtained readily, they are shown; it is noticeable that the dry bulb temperature of the air of the working place varies little from the rock temperature, and that the dry bulb temperature of the compressed air as it issues from end of air hose varies only a few degrees from the temperature of the surrounding rock; in some instances the dry bulb temperature of the compressed air as it issued from the end of the air hose was higher than the rock temperature or the dry bulb temperature of the surrounding air."

May 1, 1921

By W. C. Phalen

"The Phosphate Rock Market:Indications, in the fertilizer market, point to a prosperous condition, caused chiefly by the growing demand for all classes of fertilizer material in spite of a shortage of supplies. Both of these conditions have been caused by the war. The shortage in phosphate rock is being relieved as production increases, but the supply has not caught up with the demand for this spring's trade, at least. Reports from Florida are to the effect that more than half the necessary quota of laborers are at work. This may not appear to be a very good showing, but even this situation is en¬couraging because there is a larger force now at work than has been the case for some time, and it is steadily, though slowly, increasing. Some of the producing companies are conducting advertising campaigns to get laborers back to the phosphate fields and attractions in the way of better housing and living conditions are being offered.Producers are far more confident about the situation than they were two months ago, and though the shortage will not be met before the end of 1920, theme is a surplus accumulating over what is going out on existing contracts.Quotations are now being offered on all Florida rock excepting land pebble and this, it is expected, will be soon quoted.Quotations on Florida rock per ton are as follows:"

Jan 1, 1920

By Noel N. Moebs

Studies by the Bureau of Mines have identified geologic structures in mine roof rock that contribute to many roof falls in Appalachian coal mines. These structures, including paleochannels, scours, pinchouts, slickensides, clay veins, crevasse splays, and joints, can often be identified during, and sometimes before, mine development. Mine projections can be revised to reduce the adverse effects of discontinuitites in roof structure; large roof areas of laminated sandstone or incompetent strata generally can be delineated or inferred from exploratory drill hole data, and the need for supplementary support can be anticipated. Accurate descriptions of roof geology also provide some indication of optimum length and type of roof bolts that should be installed.

Jan 1, 1981

By R. V. Rahfuse

Noncaking 0- by 2 -inch subbituminous coal from New Mexico was gasified with air and steam at 205 prig using a stirred-bed producer to determine coal losses by entrainment in the gas for this low-sulfur, high-ash coal which contained 20 percent particles smaller than 1/16-inch sieve size. The use of fine-sized coal has particular importance because most production from mechanized mines is smaller than 2-inch size. This initial attempt showed technical feasibility for gasifying New Mexico subbituminous coal containing small-sized particles in fixed-bed producers without excessive coal loss by entrainment. Dust loss averaged about 2 percent of moisture-free coal, most of which was recovered from the gas. Ash clinkering was controlled by adding 1,010 lb/hr steam to reduce tempera¬tures in the combustion zone. Yield of low-Btu fuel gas, 150 Btu per scf, dry, amounted to 69,800 scfh from 1,490 lb/hr coal (as received) and 3,450 lb/hr air (dry).

Jan 1, 1974

By Donald M. Hausen

Diamond-bit performance and cost data accumulated by the Bureau of Mines in core-drilling schists reveal significant trends of economic interest. Low-quality, small-size drill bort were the most economical. The percentage of core recovery, type and size of bit, and bit matrix are also correlated with bit performance and costs. Detailed analyses of the factors affecting diamond-bit performances and costs are assessed in the tables, graphs, and discussion.

Jan 1, 1956

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550- and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

By S. C. Tadolini, T. M. Barczark

Mines in the western United States have had limited choices for standing support. Wood cribs were often too soft and unstable. The introduction of the Can support in the earl v 1990s provided an effective alternative, (lilt/ it remains the dominant form of tail¬gate support. Water-filled prestressing cells are now used to cap the Can and preload it to provide an active roof load. The Cluster Prop, consisting of three timber wedge props bundled to¬gether; provides more capacity than (m equivalent sized Call support and improves transport efficiency. However the Cluster Prop is less stable and does not maintain a consistent load throughout its loading profile. Pumpable roof supports are another alternative support, but the \' have not been proven in high deformation en¬vironments. This paper compares the performance characteristics o f these various support systems.

By James R. Aggson

This Bureau of Mines report presents a finite element analysis of roof stresses associated with a 4-foot-high by 18-foot-wide underground coal mine entry. This analysis starts with known loading conditions determined in an underground coal mine in West Virginia and is extended to other possible underground loading conditions. The roof failures predicted by the finite element analysis under known loading conditions correlate well with the roof failures observed underground. The most probable failure modes are identified for the various loading conditions considered. Various failure preventive measures are discussed.

Jan 1, 1979

By R. W. Fatzinger

The accident-frequency rate for placer mining in 1942 is reported as 36.923 accidents per million man-hours worked. This figure places placer-mining accident frequency slightly higher than that given for quarrying-35.7-but considerably under the 78.0 for coal mining and 56.5 for metal mining.4 Placer mining is subdivided into four types of activity: Underground, surface, dredging, and hydraulicking. It is the purpose of this paper to present and discuss safety practices in dredging and hydraulic mining; therefore, the following considerations will be limited to these two types of placer mining.

Jan 1, 1948

By Deno Pappas, Gregory Molinda, Eric Bauer, Christopher Mark, Daniel Babich

Groundfalls are much more likely to occur in coal mine intersections than in entries. NIOSH is using the experience of U.S. coal mines to determine the factors which influence intersection instability and provide guidelines for the safe excavation and support of intersections. Detailed field investigations have resulted in a database of U.S. coal mines containing 12 mines and 639 roof falls so far. By using the roof fall rate as the outcome variable, correlations between roof geology (CMRR), intersection span, and roof support have been established. Case studies have indicated that replacing 3- way intersections with 4-way intersections may not reduce the total number of roof falls. Additionally, the size of intersection spans tend to decrease with lower (weaker) CMRR. Protocols have been established for the collections of roof bolt parameters. The performance of individual roof bolts can now be tracked with roof fall rate.

By Roy H. Grau, John C. LaScola

This Bureau of Mines report contains a tabulation of methane emissions during 1980 for all coal mines located in the United States with emissions greater than 0.1 MMcfd. Listed for each mine are methane emission quantity, location, and coalbed. The report also compares records of 1975 and 1980 and describes relationships between emissions in 1980 and the Bureau's coalbed gas content data on 11 mines.

Jan 1, 1984

By D. S. Kingery, F. F. Kopsch

The practice of using two or more main ventilating fans is common at large coal mines throughout the coal-mining industry. To assure adequate and efficient ventilation at may mines, such multiple-fan systems are necessary. The hazards associated with interrelated ventilating currents if a fan fails are controversial, and to date little effort has been made to study this specific problem and to determine corrective measures. The obvious questions are: 1. Is there a hazard? 2. Under what circumtances does it exist? 3. How serious is it? 4. What are corrective measures? Most members of the mining fraternity agree that reduced quantities of air and changed airflow patterns introduce potential hazards, especially where gaseous conditions exist when mechanized methods are used in concentrated mining 0 The seriousness of the hazard depends on the ease with which methane accumlates in face areas or haulage roads, the quantity of methane in workedout areas, and the extent to which reversed air currents interfere with escape and recovery operations after mine fires or explosions. These studies cover three mines and give the distribution of air for the specific conditions show. Each mine probably has somewhat different airflowpressure relationships between fans. This depends on the number of fans, the

Jun 1, 1959

By R. Karl Zipf

Use of Salamon's stability criterion in underground mine design can prevent the occurrence of catastrophic domino-type pillar failure. Evaluating the criterion requires computation of the local mine stiffness and knowledge of the post failure behavior of pillars. This paper summarizes the status of the practical use of this important criterion and suggests important research to improve our capabilities. Analytical and numerical methods are used to compute the local mine stiffness. Work to date in computing local mine stiffness relies mainly on elastic continuum models. Further work might investigate local mine stiffness in a discontinuous rock mass using alternative numerical methods. Existing post failure data for coal pillars are summarized, and a simple relationship for determining the postfailure modulus and stiffness of coal pillars is proposed. Little actual postfailure data for noncoal pillars are available; however, numerical models can provide an estimate of post failure stiffness. Important factors controlling postfailure stiffness of rock pillars include the postfailure modulus of the material, end conditions, and width-to-height ratio. Studies show that the nature of the failure process after strength is exceeded can be predicted with numerical models using Salamon's stability criterion; therefore, a method exists to decrease the risk of this type of catastrophic failure. However, the general lack of good data on the postfailure behavior of actual mine pillars is a major obstacle. Additional back-analyses of failed and stable case histories in conjunction with laboratory testing and numerical modeling are essential to improve our ability to apply the stability criterion.

Jan 5, 1999

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have long used stationary tapered element oscillating microbalances (TEOMs®) in laboratory settings. They have served to assess the mass concentration of laboratory-generated particulates in experimental , dust chambers and they provide a reference method for comparison with other particulate- measuring instruments. Current NIOSH research is focused on further adapting TEOM technology as a wearable personal dust monitor (PDM) for coal mining occupations. This investigation's goal is to help identify, quantify, and provide means for resolving certain TEOM- related error. The present research investigated bias caused by thermal effects on filter assemblies. New filters used in the PDM for 8 h tests show an average positive bias of 25.5 pg, while similar tests of equivalent filters used in two 1400A model TEOMs show an average positive bias of 34.3 µg. The derived bias values allow correction of previously collected biased data. Also, pre- heating the filters for 24 h at 46° C shows significant bias reduction, with PDM pre-heated filters subsequently averaging -3.3 µg and 1400A TEOM filters averaging 5.9 µg. On a single-point comparison to gravimetric sampling, a 25.5 µg bias is only significant at low mass loadings. At 2.5 mg, this bias represents a negligible 1 % of the mass measurement. If ordinary linear regression is used, the bias is still insignificant. However, if the more valid weighted linear regression is used, it gives more weight to the smaller dependent variable values, which are more impacted by the bias. Consequently, what is 1% bias on a single high-mass value can translate into a larger bias percentage at high-mass values when performing a weighted regression on data that include a large number of low-mass values.

By Lars Osen

This investigation was undertaken to contribute to the understanding of underground pull tests by conducting laboratory tests under closely controlled conditions. Steel bolts, instrumented with electrical resistance strain gages, were anchored in an aluminum block, a granite block, and a steel sleeve, and were subjected to pull tests. The bearing plates used were either flat7 dished, or embossed. In pull testing a bolt that is prestressed, there is a range of loading during which bolt load is greater than the jack-applied load, This study showed that preload, the size, shape, and type of bearing plate; and the geometry of the system determine the point at which bolt load and applied load become equal. The effects on bolt load of both a theoretical solution and actual pull tests were analogous and led to similar results.

Jan 1, 1965

By A. J. Rambosek

An evaluation of diamond-bit performance data accumulated from core drilling in quartzite shows that core recovery and physical characteristics of drill bits and diamonds have economic significance. Relatively inexpensive, low-quality, small Congo diamonds will perform as well as, or better than, other diamonds used as drill bart. M-type bits set with oriented Congo diamonds provide those engaged in core drilling with near optimum combination. Various factors that affect bit performance, including size of diamonds, size and type of bits, grade or quality of diamonds, and percentage of core recovered, are evaluated by means of tables, charts, and discussion.

Jan 1, 1958