Search Documents

By D. E. Hirsch, J. W. Davis, Norman G. Foster, F. G. Schwartz

This investigation was undertaken to identify nitrogen , oxygen , and sulfur compounds (polar components ) found in catalytically cracked distillate fuel . It is significant that these compounds concentrate in the sediments and gum that form when the fuel is stored . The polar components were divided in three portions by elution from a chromatographic column filled with alumina . After the hydrocarbons were washed through the column with pentane , a benzene eluted extract was removed followed by an ether eluted extract and then an alcohol desorbed fraction . These extracts were individually distilled in a molecular still and the fractions were analyzed by gas chromatography , mass spectrometry , infrared spectrometry , and elemental and functional analyses . Naphthalene and its homologs , phenanthrene and its homologs , and other compounds such as methyl indene , C₂ quinolines , phenyl indan , and the benzothiophenes , appear in the benzene extracts . Quinolines are the major components of the lower boiling fraction of the ether extract , although carbazoles , acridans , and indoles are present in some concentration . Elemental and functional group analyses of the alcohol fraction indicated 10 percent of the distillate portion was nonhydrocarbon , and in this portion the average molecule contained more than one nonhydrocarbon element . Compounds of such complexity are not well known , and standards for positive identification are limited .

Jan 1, 1963

An examination of the Census of Fatal Occupational Injuries (CFOI) data for the period 1992-1995 shows that 659 fatalities occurred in the mining industry as defined by the SIC. Oil and gas accounted for slightly more than one-half of all fatalities (figure 1-1). The coal industry had the highest fatality rate for the 4-year period, with 35.6 deaths per 100,000 full-time workers, followed by metal (23.1 per 100,000), oil and gas (23.1 per 100,000), and nonmetal (20.1 per 100,000). The fatality rate for all U. S. industries during this same period was 5.1 per 100,000 full-time workers. Figure 1-2 compares the fatal injury rates by year for the four major industry sectors of mining to the fatality rate for all industries combined. Figure 1-3 compares age-specific fatality rates in the mining industry to those seen for U. S. industry as a whole. Fatality rates for all industries combined were lowest for young workers and steadily increased in relation to workers' ages. In the mining industry, fatality rates by age group show a U-shaped curve. Young workers under 20 years of age had the highest injury rate (54.6 per 100,000), followed by workers aged 20-24 (50.8 per 100,000) and workers over age 65 (37.7 per 100,000). Table 1-1 shows the distribution of injuries by type of injury event. The mining industry, in comparison with all industries, had a considerably larger proportion of fatalities classified as caught in or crushed by collapsing materials (9.1% and 1.9%, respectively) and fires and explosions (10.0% and 3.1%, respectively). Transportation events comprised the largest proportion of fatal injuries in both the mining industry and all industries. Within the mining industry only, transportation accounted for the largest proportion of fatalities in all mining sectors except coal. A more detailed examination of the transportation events within the mining industry showed that highway incidents (50.5%) were the most common, followed by nonhighway incidents (22.2%), pedestrian incidents (10.6%), and those incurred during rail, water, and air transport (15.7%). Incidents involving caught in or crushed by collapsing materials comprised a higher percentage of injuries in the coal and metal sectors, while fall-from-height incidents were more frequent in the oil and gas sector. The classification system used in CFOI for type of injury event is not compatible with any variables contained in the MSHA data; therefore, direct comparisons are not attempted. [ ]

Jan 5, 2000

By P. S. Lewis

Shortage of natural gas is reviving interest in low-Btu fuel gas made by gasifying coal in fixed-bed producers. The Bureau of Mines gasified strongly caking Pittsburgh bed coal over test periods lasting four days in an experimental gas producer located at Morgantown, W. Va, Mechanical stirring throughout the fuel bed was effective for keeping the fuel moving and this stirring made the operation successful; hence, the gas producer was named the stirred-bed producer. Nuclear density gages were applied as control instruments to indicate coal flow and fuel level, and to record the frequency and location of void spaces in the bed, The gas, of nominal 140 to 165 Btu/scf calorific value, could be burned in a boiler for generating steam.

Jan 1, 1972

By W. H. Herschel, E. W. Dean

"IntroductoryThe common practice of the petroleum industry is to measure viscosity by the use of instruments of the efflux or capillary tube type. The Saybolt universal viscosimeter has been tentatively adopted as a standard by the American Society for Testing Materials and is used extensively in the United States.Several instruments of foreign origin are also more or less familiar, such as the Redwood, the Engier, and the Baroey.Effina-type viscosimeters are well adapted to the ordinary needs of petroleum testing laberatories as they are simple and rugged in construction and away to manipulate, even in the hands of operators lacking scientific training. They have, however, certain limitations and for certain spacial types of work there are notable advantages incident to the use of the so-called torsion types of type of viacosimeter. The most satisfactory type of torsion viscosimeter now available in the market some to be that of MacMchael, which has been discussed in detail in a recent paper (Herschel, W. H., The MacMichael Torsional Viscosimeter. Jour. of Int. and Eng. Chem., vol. 12, 1920, pp. 282-286). The present paper indicates conditions under which this viscosimeter may be used to advantage in the petroleum laboratory, and outlines simple methods of operation and calibration."

Jan 1, 1921

By W. C. Phalan

"Prewar Conditions:Metallic magnesium may be considered a war metal, but a war metal with a future, so far as the industry in the United States is concerned. Its production in the United States prior to 1915, on a commercial scale, was negligible, but imports prior to that year may be taken as a gaze of the demand for the metal. Unfortunately, magnesium was not listed separately by the Department of Commerce prior to the war, among the importations, but was included with other metals, as follows: ""Barium, calcium, magnesium, sodium, and potassium, and alloys of which said metals are the component materials of chief value."" However, the imports of metals enumerated other than magnesium were probably small, so that the importations under the above caption may be considered chiefly metallic magnesium in one form or another and, therefore, is an approximate gage of the demand for the metal in the United States. These imports were as follows:These figures are so close that they give a good idea of the figures for the respective calendar years.Of this prewar use, it has been estimated that about 85 per cent was used annually and in approximately equal quantities in the production of (1) flash-light powder, (2) fire works, (3) aluminum casting work, and (4) nickel and nickel-copper alleys, such as monel metal, etc. The re¬maining 15 per cent was employed for general uses, such as deoxiding brass and other copper alloys in foundry work, and to a small extent in laboratory and research work."

May 1, 1920

By L. C. IlsLey

"There is an old saying that ""It is too late to lock the stable after the horse is stolen"". Is not this just what is being done by many mine operators today when it comes to buying safe electrical equipment for gaseous and dusty coal mines?The ""open type"" of electrical equipment or even the ""half safe"" type represents the unlocked stable. After the mine disaster, and after men have lost their lives, the lock is put on - that is, safer equipment is installed.For example, an open type of electric coal drill was used in a gaseous mine in West Virginia, This was the probable cause of the death of 27 men. A half safe type of electric coal-cutting machine was used in a gaseous mine in Pennsylvania. This was likely the cause of the death of 36 men. An unapproved, unsafe type of flame safety lamp was used in a gaseous and dusty mine in Utah. This was the all¬eged cause of the death of 171 men. All three disasters happened within the last six months, and seem to have been avoidable if proper equipment had been used.It is understood that more rigid requirements will be enforced in West Virginia. The committee of State mine inspectors made definite recommendation for im¬proving the conditions in the given mine in Pennsylvania. The Industrial Commission of Utah have already issued new orders which will remedy the use of unsafe lamps in that State.These acts and recommendation are all good and will help prevent accidents in those States in the future. Is it not a pity that such recommendations and order were not made a little earlier before the tell of life had been exacted? Is it not a pity that other States will not take these lessons to heart and safeguard their mines before and not after disasters take place?Electric current can cause accidents in five general ways as follows: (1) By shock to persons; (2) by igniting powder; (3) by igniting gas; (4) by igniting coal dust; and (5) by setting fire to inflammable material such as timber and coal. A great many accidents from these causes are preventable if proper care is taken. Most of the accidents caused by sparks and flashes from electrical apparatus would not take place if approved electrical equipment was used. By approved equipment, the writer means equipment that has been tested and formally approved by the Bureau of Mines. So far as known, up to the present time, no disasters have been caused by sparks or flashes from equipment having the Bureau's approval."

Jul 1, 1924

By Donald W. Ross

"INTRODUCTION Sponge iron has been made commercially since 1912 at a Swedish ceramic plant; and the product, known as Swedish disk—type sagger sponge iron, has an excellent reputation as a superior furnace feed wherever high—grade steels are made. The general procedure for making brickyard sponge iron was described frequently in Swedish technical journals prior to 1932 and at that time consisted in filling clay refractory containers, called saggers, with a super-concentrate of Gellivare magnetite plus the necessary amount of solid reducing agent and desulfurizer and then firing in a Hoffmann ring furnace, as used in the ceramic industry.The early Swedish publications describe two types of brickyard sponge iron: (1) An inferior high-sulfur product obtained by mixing the ore and reducing agent, and (2) a high-grade low-sulfur product in the form of coherent disks 7 to 9 inches in diameter and 1 to 1-1/2 inches thick made by the saggers with alternate layers of solid-fuel reducr and of uniaxed ore."

Sep 1, 1945

By H. A. Watson

Laboratory tests on three commercial methane detectors, two combustion-type detectors and one interferometer-type detector, were made by the Bureau of Mines to determine their response to certain single and multiple flammable gases mixed with normal and abnormal air atmospheres. Although both types of detectors responded accurately to methane-normal air mixtures, they did not show correct concentrations for other single flammable gases in air. Uniquely, the response of the interferometer-type detector to hydrogen was in a negative direction. The effects of individual gases in multiple flammable gas mixtures were approximately additive. In oxygen-deficient atmospheres the methane response of the interferometer-type detector erred on the high side, but only in very low oxygen concentrations were the combustion-type detectors affected-showing low, erratic methane readings.

Jan 1, 1966

By M. Townsend, E. L. Petsonk, B. Fedders, M. Niggemeyer, H. Abrons, E. Daniloff, J. Griffin, K. Kinsley

In certain populations, nonspecific airway hyperreactivity (HR) is associated with increased respiratory symptoms and decreased lung function. We analyzed standardized pulmonary symptom questionnaires and pre-shift spirometry with methacholine inhalation challenge (Chatham, M. et al, Chest 82: 15) on 228 control workers (C) with no known exposure to occupational hazards, and 200 underground bituminous coal miners (M). M and c were similar in age, height, sex, and smoking status. HR (defined as >15% fall in FEVI after up to 5 vital capacity breaths of 25mg% methacholine) was found in 25% of M and 28% of C (NS). M showed higher% predicted FEVI (%PFEV) than c (M 107%, C 104%*). 28% of current smokers showed HR versus 22% of never smokers (NS). Current smokers showed reduced %PFEV but were not different from lifelong non-smokers regarding prevalence of HR. Subjects with HR showed reduced %PFEV, (HR 101%, not HR 107%*) but M and c with HR showed similar reductions. M had more dyspnea and chronic cough than c*. Hyperreactivity was associated with increased symptoms in controls but not miners. In our study, the prevalence of HR in coal miners was similar to nonminers, and did not explain miners' respiratory symptoms. * P < 0.05

Jan 1, 1989

By M. S. Seehra, V. S. Babu

"INTRODUCTION The accurate determination of the free silica index in coal mine dusts is an important requirement because severe health hazards are believed to be associated with the inhalation of respirable-sized silica particles.1-6 Free silica refers to the three polymorphs of silica (Si02)viz., quartz, cristobalite, and tridymite-although quartz is usually the dominant form in most mine dusts.6 The free silica index is the concentration in micrograms of free silica in air per m3 of air sampled corrected to standard conditions of 25°C and 760 mm/Hg, the present MSHA (Mine Safety and Health Administration) limit on time-averaged basis being 100 µ.g/m 3 for coal mines. A recent review7 has concluded that quartz, cristobalite, and tridymite particles impart nearly equal long-term hemolytic damage when compared on a per unit surface area basis.At present, two experimental methods-viz., transmission infrared spectroscopy (TIRS) and x-ray diffraction (XRD)-are commonly used for the determination of silica concentrations in mine dusts. In TIRS, which has been adopted by MSHA and is commonly called the P7 method, the silica absorption band near 800 cm - 1 is used for quantification. However the mineral kaolinite, which is commonly present in mine dusts, also has absorption band, albeit weaker, at 800 cm- 1• To correct for this interference, one uses the stronger 915-cm -1 band of kaolinite to determine the concentration of kaolinite, and the kaolinite contribution to the absorbance at 800 cm-1 is then determined from a calibration curve, leading to the determination of silica by subtraction. In the XRD technique, usually an internal standard such as CaF 2 is used to determine the concentration of silica from line intensity measurements. XRD has the added advantage that concentrations of quartz, cristobalite, and tridymite can be determined.8•9 In an exhaustive study on the precision of the techniques ofTIRS and XRD for monitoring worker exposure,9 the conclusion has been reached that both methods measure silica within 253 of the ""true"" value 953 of the time in a single laboratory."

Nov 1, 1995

By Charles L. Kimbell

This study is intended to serve three roles. First, it represents a global overview and summary to supplement and complement the five regional companion volumes of the 1991 edition of the Minerals Yearbook International Review. In this regard, it also extends previous time series under this title that appeared as the introductory chapter to the international volume of the Minerals Yearbook from the inception of that volume in 1963 until it was subdivided into separate regional volumes in 1989. The basic statistical presentations herein generally contain data through and including that for 1991, although in a few instances the most recent statistics are those for earlier years because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting the world&apos;s mineral industry that have occurred between the end of 1991 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

By S. P. Kinney, P. H. Royster, T. L. Joseph

"The study described in this paper, on the reactions in an iron blast furnace, is part of the investigation being conducted by the Bureau of Mines on combustion of coke and the reduction of iron oxides in the blast furnace. Previous study of the combustion zone of the iron blast furnace, by means of a series of as samples taken through the tuyeres across the hearths of 13 blast furnaces, showed that the combustion of the coke in the blast-furnace hearth is complete at a distance of 32 to 40 inches from the nose of the tuyere, measured horizontally toward the center of the furnace. The results of this previous work are sum¬marized in the curves shown in figure 1, where it will be noted that practically all of the oxygen disappears at a distance of approximately 30 inches from the nose of the tuyere.In order to determine the height at which oxygen is found in a vertical direction above the tuyeres - it had been suggested that the combustion zone turned upward near the tuyere and to obtain comparisons with the samples taken at the Bureau of Mines experimental6 (5-ton) blast-furnace at Minneapolis, the Bureau extended the gas sampling on a commercial furnace to a number of planes between the tuyere level and the stock line. The sampling was conducted on a 300-ton furnace, making foundry iron, operated by the Central Iron and Coal Co., at Holt, Ala. The furnace was smelting Southern red and brown ores and nodules from pyrite sinter. Figure 3 is a vertical section of the furnace showing the six planes sampled."

Apr 1, 1926

By C. E. Augustine, P. Nicholls

"INTRODUCTION A layer of soot on the heating surface of a boiler decreases efficiency because it increases resistance to the flow of heat, with the result that the heat transfer to the water is lower and the temperature of the flue higher than they would be if the surface remained clean. The percentage of reduction in heat transfer depends on the position and area of the sooted. The percentage of reduction in heat transfer depends on the position and area of the sooted surfaces, the thickness of the most, until the percentage of the total heat absorbed by those surfaces when clean; thus it will vary with the type of boiler and in particular with the ratio of the area of the convection heating surface to the total area. Medium-size and large boilers usually are equipped with soot blowers, and tests have been published giving the increase in efficiency resulting from removal of the soot. Fuel savings up to,8 percent have been reported, but 4 to 5 percent is probably more conservatives. However, these savings may not be due wholly to a reduction the thermal resistance of the surfaces but may be due partly to improvement in the combustion because of better draft or more uniform flow of the gases. In addition, the deposits on the surface of boilers include as a clinker, and as the size of the boiler and the rate of burning increase very little or none will be soot.There are no corresponding test data on small boilers operated at low rates of burning. In stall boilers, deposits are much thicker, and it might be expected that the reduction in efficiency would be greater; in fact, statements have appeared suggesting that the decrease may be as high as 50 percent. This investigation was undertaken because the Bureau frequently receives requests for authoritative information on the effect of soot in small and other heating boilers."

Feb 1, 1935

By J. R. Thoenen

[Since the publication of the preliminary report on this subject in July, 1927, (The Wire Saw in Slate Quarrying, Preliminary Report, Serial No. 2820, by Oliver Bowles) the wire saw has been in constant daily operation at the quarry of the Colonial Slate Company. Luring this time between twenty end thirty successful cuts have been made varying in length from forty-five to ninety-two feet and in depth from six to ten feet. No accurate time records have been kept on these cuts but they have totaled over 12,000 sq. ft. of area and required 19,000 lineal fact During these cuts the average speed of cutting has risen from the 12.8 sq. ft. per hour obtained in the original recorded tests to between 15 and 20 sq. ft. per hour, with the present rate running very close to 20 sq. ft. per hour at this quarry.]

Jan 1, 1928

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

Estimate costs for projected uranium in-situ mining operations. Approach Develop a computer model and an associated data base which will allow users to supply data applicable to a specific mining site in order to estimate total capital and operating costs for a potential in-situ mining operation at the site. How the Model Works The model requires a minimal amount of input from the user. The data input must be known or estimated information about a potential in-situ mining operation. The user can also supply any additional project specifications. The computer model uses a process-engineering approach and determines through a discounted cash flow analysis the total capital and operating costs for the life of the project. This time-span measures from the start of the pilot-scale operation through to the site&apos;s restoration and reclamation. The model will determine the production cost per pound of material mined subject to the rate of return identified by the user. Conversely, it will also solve for the rate of return realized for the specific sales price per pound. [ ] Currently the model&apos;s data base can tai ns costs, rates, and specifications for Texas and Wyoming, the only states where commercial uranium in-situ mining is being conducted. However, this model can be used by anyone who is conducting in-situ leaching or who plans to leach uranium in-situ. At least part of any uranium deposit has a potential for in-situ mining.

Jan 1, 1982

By Martin H. Rogoff

The presence of antibiotic materials extractable with polar organic solvents was demonstrated in coals of various ranks. Since these antibiotics occur in low concentrations, 200 pounds of a high-volatile C coal was extracted with acetone at room temperature to obtain sufficient material for detailed study. The biologically active materials in the extract were concentrated by extracting with aqueous sodium hydroxide. The fractions soluble in sodium hydroxide inhibited bacterial cultures when present in concentrations comparable to those at which other antibiotics are active (5 µg/ml). Steam distillation of the extracts did not yield highly active materials, contrary to the finds of other investigators. Mass spectrometry of the extract indicated, mainly, the presence of 6-ring compounds in the region of mass 324 to 392. The predominance of 3-ring aromatic systems found by ultraviolet analysis suggests compounds such as biphenanthryl or similar structures. The activity of the hydroxide- soluble material decreased markedly when the phenolic hydroxyl groups were transformed into trimethylsilyl ethers. Hydrolysis of the ethers yielded a product having the same activity as the original material, which indicates that phenolic compounds are largely responsible for the antibiotic activity observed.

Jan 1, 1963

By Cleo G. Rall

The value of brine analyses in the study of petroleum-engineering problems was recognized early in the history of petroleum. The Bureau of Mines before 1928 had indicated in several reports.3/ ways in which analyses might be used. Because of the confusion resulting from attempts to correlate the work of different chemists using greatly varying methods of analysis and systems of computation and expression of results, a paper presenting the methods used by the Bureau of Mines was prepared and published in 1928. This system of determining the characteristic constituents of oil-field waters and of calculating and reporting results has been widely adopted by the petroleum industry. The earliest and most obvious use of water analyses is determination of the source of water infiltrating into petroleum and natural-gas wells. For this purpose it is necessary that an analysis of the connate water of the formation from which the oil is produced be available and that an analysis of the contaminated water be made. By comparing these analyses with those of connate waters from formations higher in the structure, the formation from which the infiltrating water comes may be identified.

Jan 1, 1953

By L. K. Weaver

Bureau of Mines investigated the progressive impact that petroleum (crude oil and condensate) operations in the Gulf of Mexico have had on onshore operations and the expected effect of increasing activities in this area on future petroleum supplies from domestic sources. The data analyzed include capital expenditures, number of wells drilled, success ratio for exploratory wells, daily production per completion, annual producing rates, and oil reserves. The report compares offshore and onshore data and ascertains trends in petroleum industry operations. Observed data and trends indicate that in the near future Gulf of Mexico development and production will continue to increase relative to total U.S. petroleum activity. By 1975 annual oil and condensate production from the Gulf of Mexico is expected to be in the range of 750 million bbl to 1,150 million bbl, and account for approximately 20 to 30 pct of the estimated total domestic production.

Jan 1, 1969

By Richard J. Mainiero, Michael J. Sapko, James H. Rowland III, Marcia L. Harris

All explosive materials produce a cloud of reaction products, the most toxic of which is nitrogen dioxide (NO2). In the study reported here, 4.5-kg (10-lb) charges of blasting agent confined in either thin-wall 10-cm (4-in) diameter galvanized pipe or 10-cm (4-in) schedule 80 seamless steel pipe were detonated in a closed chamber. The detonation gases were analyzed for NO2, nitric oxide (NO), ammonia (NH3), hydrogen (H2), carbon monoxide (CO), carbon dioxide (CO2), nitrogen (N2), oxygen (O2), and methane (CH4). Data were evaluated to determine the kinetics of the oxidation of NO to NO2. Analysis revealed that the only mechanism for NO loss for the conditions existing in the chamber was the reaction 2NO + O2 6 2 NO2. The rate constant was 2.08 @ 10-38 cm6 molecules-2 sec-1 for the rate equation -½d [NO]/dt = K @ [NO]2 @ [O2] for NO concentrations up to 100 ppm. The rate constant is in agreement with that recommended by Baulch, Drysdale, and Horne (1973).