Search Documents

By A. W. Fahrenwald

"About two years ago the Bureau of Mines, Department of the Interior, and the University of Idaho undertook an investigation of classification in its relation to table concentration of Idaho ores. The cooperation of the management of the Bunker Hill & Sullivan Co. in placing at our disposal their West Mill and facilities as desired, offered an unusual opportunity for studying the field of hindered classification in its practical and economic relation to table concentration.It has been shorn theoretically, and demonstrated experimentally, that ore products are more easily and economically concentrated on tables if the natural feed, consisting of various minerals and of all sizes of particles of each mineral, be classified or grouped into a series of products in which the mineral particles of greatest density are small in diameter relative to the diameter of the mineral particles of lesser density. Products in which the maximum difference in diameter of light and heavy minerals occurs are to be obtained only by true hindered settling classification. To our knowledge there has never been a really good hindered settling classifier used in practice and the present tendency seems to be to by-pass any attempt at such classification.After a careful study of the nature of hindered classification and of the requirements for hindered settling in practice, a classifier has been developed that takes fullest practical advantage of the widely known, but generally only meagerly understood, condition of hindered settling so well analyzed a number of years ago by Dr. Richards.The present paper presents briefly some of the more important practical results accruing through the investigation."

Jun 1, 1924

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free- port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in determining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ton of coal, for a total of 190 to 400 billion cubic feet of methane in this coalbed in Fayette County.

Jan 1, 1977

By Kathleen Madland Kowalski

In recent years the issue of human stress response in emergency workers has begun to receive attention. This paper presents a rationale for considering human stress as a significant factor in the management of emergencies It discusses the concept of stress, Critical Incident Stress in emergency responders, and intro¬duces the Critical Incident Stress Debriefing (CISD) process. It is suggested that in a disaster, the CISD process can improve the effectiveness of response teams on site, their turnaround time on site, and post disaster time off the job. This paper, prepared by a US Bureau of Mines research psychologist, offers some ideas to the mining industry in general, mine rescue trainers and more universally, to those responsible for developing emergency management plans.

Aug 1, 1998

By Thomas C. Miller, Charles E. Mongan

"This publication is a progress report on Bureau of Mines studies in applying sonar techniques to roof-control problems in coal mines. Preliminary tests in the laboratory were made on layers of roof rock. To apply the experience thus obtained, a unit was designed and constructed and was used underground.The term ""sonar technique"" refers to the system of generating a beam of sound waves, shaping and directing the beam, introducing the beam into a medium to be studied, and examining any returning waves with a view of inferring the nature of the material traversed by the waves and the presence of interfaces or obstacles in the medium.The theory and actual underground experiments indicate that the sonic method is feasible. Information from physical tests made in the Bureau's Experimental mine confirmed the validity and potential usefulness of the sonar method. Lighter and more compact apparatus is desirable, and permissible equipment suitable for use in gassy or dusty mines must be developed. However, no particular difficulties are anticipated; consequently, this scientific approach to the exploration of roof strata shows definite promise. INTRODUCTIONThe problem of roof control in the coal-mining industry is of major importance. More than 50 percent of all coal-mine fatalities and 25 percent of all nonfatal serious injuries are caused by falls of roof, face, or ribs. The Bureau estimates that more than $128 million was spent by the coal-mining industry in 1958 for supporting roof."

Feb 1, 1960

By W. P. Yana, J. B. Littlefield

"INTRODUCTION AND OBJECT OF EXPERIMENTAn explosion in and rupture of a gas-tight switch box on an electric loader in a mine located near Pittsburgh indicated that the cause was an internally generated inflammable gas-air mixture. This led to the suspicion that moisture condensation or ""other unusual conditions might have caused a spark or are across the surface of the material and that the heat may have created a carbonized path across the synthetic plastic base which would then conduct a large current with the generation of considerable heat and thermal decomposition of the base materials base in the box which exploded gave every indication that this series of events had taken place, and accordingly it was desired to determine what explosive gases such a decomposition of these insulating materials would produce.ACKNOWNLEDGMENTSThe desirability of making this investigation was suggested to the authors by L. O. Ilsley, supervising engineer, electrical section, Bureau of Mines, to whom the occurrence of an explosion in a switch box had been reported. The writers also acknowledge with thanks the assistance of L. B. Berger, chief scientific aide, health laboratory section, Bureau of Mines, in checking the calculations in the tables. DESCRIPTION OF MATERIAL INVESTIGATEDThe ten materials used in the tests, identified by letters A to J inclusive, are described in a succeeding list of materials. All the materials except I had a phenolic odor, especially when freshly cut."

Dec 1, 1932

By Kathleen Madland Kowalski

In recent years the issue of human stress response in emergency workers has begun to receive attention. This paper presents a rationale for considering human stress as a significant factor in the management of emergencies. It discusses the concept of stress, Critical Incident Stress in emergency responders, and introduces the Critical Incident Stress Debriefing (CISD) process. It is suggested that, in a disaster, the CISD process can improve the effectiveness of response teams on site, their turnaround time on site, and post disaster time off the job. This paper, prepared by a US Bureau of Mines research psychologist, offers some ideas to the mining industry in general, mine rescue trainers, and more universally, to those responsible for developing emergency management plans.

By A. R. T. Denues, A. P. Rowles

"INTRODUCTION Summarized data developed by J. E. Crawshaw and E.J. Murphy, 4/of the Explosives Division of the Bureau of Mines, suggesting marked variations in oxygen condition in three permissible explosives, have been reported 5/. Such variation is of interest in other work, it having been shown, for example, that the oxygen condition may have marked effect upon the products 3/ and the propulsive strength 7/ of explosives. It seemed that a more detailed presentation and more usual statistical analysis of these data might be of considerable general interest and not complemented in the literature.This report presents both the original data developed by Crawshaw and Murphy and the results of a simplified but seemingly acceptable statistical analysis of these data. The logical ground for this analysis might seem somewhat questionable because of the lack of systematic information concerning the extent of errors in the analytical procedure but the data show that there are several cogent and seemingly unequivocal indications of real heterogeneity in the explosives."

Jun 1, 1942

By R. K. Koch

In seeking substitutes for such critical metals as chromium, cobalt, and nickel, the Bureau of Mines investigated techniques for shape-casting titanium in rammed sand molds. Castings were made in olivine, garnet, chromite, and, for comparison, zircon. It was found that commercial-grade castings up to 31 lb (maximum capacity of furnace) could be made in zircon or olivine molds if a zirconia mold wash was used. Castings up to 4 lb could be made in chromite molds, but heavier castings suffered from some mold-metal reaction. Garnet molds were found to be unsatisfactory for castings of all sizes because of gas blows and rough surfaces. In other tests shell castings of acceptable quality were produced in water-glass-bonded zircon and olivine molds up to weights of 8 lb, but chromite molds were unsatisfactory because rough casting surfaces were caused by mold-metal reaction. Unlike the currently used commercial processes, neither the rammed-sand nor the shell-molding processes developed by the Bureau of Mines generate noxious fumes at any step.

Jan 1, 1980

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of new' water and reused 3.8 billion gallons for a total usage of 12.4 billion gallons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain thin high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ire near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand For new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements in the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By Lijun Xu, Jan M. Mutmansky

"Mutmansky, J.M. and· Lijun Xu, 1989. Some observations on particulates collected in underground coal mines using diesel and non-diesel equipment. Min. Sci. Technol., 9: 207-218.The results obtained when sampling twenty underground coal mine sections, each in a different mine, are outlined. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a fairly detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons of the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines lising diesels only for outby utility haulage. Particulates in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be drawn from the limited data, a more detailed study of particulates may provide a better picture of particulate loadings.IntroductionThe subject of particulate emiss1ons from underground diesel equipment is currently a very important topic as health concerns and regulation of diesel particulate emissions have created new environmental problems for mine operators. The amount of particulate matter originating from diesels has not been extensively measured and problems of differentiating coal and mineral dust from diesel particulates make existing data questionable.However, it is necessary to make an assessment of the problem in order to solve it. It is known that particulates from diesel engines are solid aerosols formed in the combustion process. Technically, this places the particles in the category of fumes. It is also known from tests where no mineral dust could be a factor in the measurements that about 90% of diesel particles are less than 1 µm in aerodynamic diameter [3]. To measure the diesel component of a coal/diesel particulate to measure, Johnson et al. [2] have developed procedures for utilizing laser Raman spectroscopy. The determination of diesel content in a coal/diesel mixture is difficult due to the chemical similarity of the two organic materials. However, laser Raman spectroscopy, which is often used for identification of organic materials, has potential if the Raman spectra for the two materials are different and unique. The study concluded that an accuracy of ±~% could be achieved for mixtures containing up to 55% diesel particulate. The method is relatively complex and would need further development for routine application."

Jan 1, 1990

By D. J. Bauer

Solvent extraction separation of light group rare-earth elements in a quaternary ammonium compound-chelating agent system was demonstrated in single-stage studies, Typical separation factor values obtained were 93 for lanthanum-praseodymium, 5.4 for praseodymium-neodymium, and 11.6 for neodymium-samarium. These values are significantly higher than those obtained using organophosphate extractants. Further studies in a 20-stage countercurrent mixer-settler resulted in the production of 99 percent lanthanum (oxide basis) at 96-percent recovery. Subsequently, 88 percent of the neodymium with a purity of 92 percent was recovered in the raffinate.

Jan 1, 1971

By Jr. Smith

To investigate the effects of flow geometry on laminar flames, studies are in progress in this laboratory employing Bunsen-type burners with rectangular cross section. Interpretation of these studies requires a determination of the flow velocity at all points of the rectangular cross section for one dimensional steady laminar flow. In addition, values of the velocity gradient at the boundary for such flows are needed in the interpretation of blow-off and flash-back studies with burners of rectangular cross section. The hydrodynamical problem of steady laminar flow of a viscous fluid in channels of rectangular cross section was solved by Stokes. His results have been quoted by Love21 and by Dryden, Murnaghan, and Bateman,§/ and they have been discussed by Boussines and by Paschoud. It may be noted that the steady laminar flow of a viscous fluid in channels of rectangular cross section constitutes a hydrodynamical analogue for the problem of the torsion of an isotropic prism of rectangular cross section.

Jan 1, 1952

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the third report of investigations by the Bureau of Mines in cooperation with industry to establish the value of electrolytic manganese in the manufacture of ferrous and nonferrous alloys. The manganese was produced by the Bureau at its Boulder City pilot plant from domestic ores and by the process developed by it. 4/ The work was done under the direction of R.S. Dean, assistant director, Bureau of Mines, and R. G. Knickerbocker, chief, metallurgical branch. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steels 5/ and the second with its use in acid electric or open-hearth low- and medium-carbon steel castings. 6/The present report treats of the use of electrolytic manganese in the manufacture of low—carbon rimmed and killed steels. A résumé of these three investigations and two others appeared in the magazine STEEL. 7/ Further reports will be published as tests are completed at some 70 industrial plants. All tests were made on full—scale heats or melts, and the resultant product was processed and used commercially."

Jul 1, 1945

By Arne Landsberg

Accessory metals, although valuable resources, present possible environmental concern in the smelting of base metals. The Bureau of Mines, U.S. Department of the Interior, has undertaken research to define the chemistry involving these metals. Arsenic in copper smelting is the first to be investigated. Roasting, the first step in many copper smelters, was chosen for initial investigation because of the potential for arsenic removal in this primary process. Simple, static-bed, vaporization experiments were devised to obtain the data in this study. Ancillary transpiration and mass spectrometry were also used to delineate conditions necessary for arsenic volatilization from a roaster feed. For nearly complete arsenic removal, a temperature of 650°-700° C, a reducing atmosphere including carbon monoxide, and a source of sulfur were found to be essential.

Jan 1, 1980

By M. S. Oudenhoven

This Bureau of Mines investigation was conducted to obtain an experimental solution of stress changes in the vicinity of a circular opening in an infinite plate. Plates were stressed biaxially in compression and subjected, by four different-length shoes, to a uniform pressure at opposing points on the opening periphery. The principal stresses along the vertical and horizontal axes, which result from peripheral pressure, were obtained from the photoelastic analysis of four frozen-stress epoxy models. These principal stresses were then super-imposed on the mathematically determined principal stresses (along the same axes) obtained from a theoretical biaxial stress field in which the magnitude of the lateral pressure was one-third that of the vertical pressure. The results indicate that an increase in shoe length increases the radial compressive stress and the tangential tensile stress (except tangential compression at r/a = 1, which exists for all shoe lengths). Also, a partial control of the stresses within one-half radius of the opening surface is accomplished by a change in the magnitude and placement of peripheral pressure.

Jan 1, 1966

Assist in controlling or extinguishing fires that occur in abandoned mine lands (AML) by providing a compilation of information on past fire control projects, the estimated extent of the current problem, and factors affecting the occurrence, propagation, and extinguishment of AML tires. Conventional fire control methods and their probable effectiveness are evaluated. Background Fires that occur in abandoned coal mines, waste banks, and coal outcrops constitute a serious health, safety, and environmental hazard from toxic fumes, deterioration of air quality, and subsidence. Although fires on AML occur in every coal-producing State, the severity of the problem varies, with most underground fires occurring in Kentucky, Pennsylvania, and Wyoming. Surface fires are prevalent in Kentucky, Pennsylvania, and West Virginia. Methods to extinguish or control AML fires, including excavation, fire barriers, and scaling, are generally expensive and have a relatively low probability of success (see figures 1 and 2). Bureau of Mines Study The Bureau compiled information from a variety of sources and found that the problem of AML fires is a serious one. Such fires can involve a high degree of hazard and can be difficult and costly to control. AML fires usually involve smoldering combustion in outcrops, waste banks, or abandoned mines. Given the nature of these fires, it is unlikely that the extent of the problem or the cost of solutions will decrease in the near future.

Jan 1, 1992

By HOWARD I. OSHRY, James W. Ballard, H. H. Schrenk

Photometric instruments were designed and built for use with X- ray and spectrographic apparatus for the investigation and analysis of a variety of materials of hygienic interest . The instruments are simple in design , may be constructed economically , and have a number of features that make them stable and easy to operate . They are readily adaptable for measurement of either X - ray diffraction patterns or spectrographic films or plates . Because of these features and the interest shown in the instruments , they are described in detail , and reference is made to their application in the laboratory .

Apr 1, 1942

By L. C. IlsLey

One of the details which the engineers observe closely in conducting tests on explosion-proof type equipment at the Pittsburgh experiment Station of the Bureau of Mines is the construction of covers and their means of fastening. These covers are of particular concern from a safety standpoint, because they are very liable to be frequently disturbed for the purpose of making inspection or repairs to internal parts of motors, controllers, etc. When depended upon to permit frequent inspections it is desirable from a practical operating standpoint that the cover be easily and quickly removed and replaced. The position that been taken by the Bureau of Mines is that the questio of ease with which covers will permit inspection should be determined by the mamu- facturer and the user. If the scheme used requires considerable effort, as in the removal of several bolts, it has been assumed that the one going to all this trouble to get the covers off could be trusted to put the cover back in place properly, especially as the approval plate generally calls specific attention to this point. Where a cover is simply screwed in place, fastened by a single bolt, or secured by a hing in or other similar arrangement, the bureau has not been willing to assume that the, cover would in all cases be properly fastened and has required further security by means of a lock or seal. In the course of its investigations the bureau has had occasion to inspect and test five types of covers as follows: (1) Covers having two plane surfaces bolted together. (2) Covers having two plane surfaces held together by lugs, clamps, or other means besides bolts. (3) Covers which have screw thread and fit a similar thread in the compartment. (4). Covers having plane surfaces with the addition of a tongue-and-groove joint at about the center of the plane surface and in general secured by hinge pins or similar means of fastening. (5) Covers in the form of an annular ring accurately fitted to a motor shell which can be rotated around the shell, and thus make easy access to inspection openings in the shell and rotated back again to effectively seal these openings. Tests. have also been made of large bolted covers having a smaller and more accessible cover within the large one, which could be opened for inspection purposes.

May 1, 1930

By G. W. Jones

[The determination of the ignition tcqornturc ol" dict:iyl cther and othylene in air ma o;GrT;en rir..ic'r. is dcscribed In thin report J'IF.R mqdo primarily for comparison rritll sinilnr d~ton:in:~tions of ot; cr co~~o~imS-r, in the same apparatus and using the r?.:?.r.~o 1a.borntorg t cchzllique The investigation was conducted at the 2ittsbur;;h Experiment Station of the United States wcau 02 hii2cs vritEl tl~c cooperation of licrclc & Co., Inc.]

Jan 1, 1935

By D. Hurrington

For severlrl 1e1.rs the Bureau of Mines has studied dust and ventili in metal mines a.s a.tfeoting the hea.l th, safety, and efficiency of underground workers. From its beginning this work haa been directed by G, s. Rice, chief mining engineer, A. cooperative agreement was ma.de in 1915 with the u. s. Publi Health Service; since that time tield obmervations 1n metal mines in Arizona, California, Idaho, Montana, Michigan and Nevada, and less extensive observation, in several other States have been made by mining engineers of the U, s. Bureau of Mines, and doctors of the u. s. Pu.blic Heal.th Service. Most of the analyt:J:eal work has been done by chemists, petrographers, and other specialists in the Pittsburgb station ot the Bureau of Mines, Numerous articles have been printed by the otticial and the technical press on this important in•estigation; 1n response to the need for a btiet bibliography of this literature. it has been compiled to facilitate accp1,intance with published data ot1. the subject,

Jul 1, 1922