Search Documents

By M. Orchin

THIS PAPER is concerned with two aspects of the behavior of coal: (1) Dispersion by solvents atmospheric pressure and high temperature and (2) the destruction and regeneration of the coking properties of coal. Several pure polycyclic compounds and a coal-tar fraction were found to extract 95 percent of the organic material of a bituminous coal. About 20 percent of the extract was soluble in benzene, and this fraction contained the ?coking principle? of the coal. From an extensive chemical spectroscopic, and x-ray study of the benzene-soluble material, some conclusions could be drawn concerning the composition and structure of this fraction of coal. A possible commercial application of the extraction technique is in the preparation of low-ash carbonaceous material for the manufacture of electrode carbon.

Jan 1, 1951

By Anthony T. Lannacchione, Donald G. Puglio

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

By C. J. Thompson

Two sulfur compounds--the 2,2,5-trimethyl- and the 2,2,5,5-tetramethyl derivatives of thiacyclopentane--were identified in Wilmington, Calif., crude oil, using microdesulfurization and gas-liquid chromtography techniques.

Jan 1, 1963

Many different types of structures and materials have been used to build mineral processing facilities throughout the years. Although structure type and building material were not viewed as significant factors affecting the health of employees in these facilities when they were built, the National Institute for Occupational Safety and Health (NIOSH) has found that building type can impact respirable dust and noise levels. NIOSH performed a study in which it evaluated three building types: masonry, an open-structure design, and a steel-sided design. This study indicated that an open-structure design (no walls) was superior from both a dust and noise (health) standpoint when compared to the other two structure types. Therefore, companies may want to consider this design when building new structures.

By C. K. Lee

This Bureau of Mines report presents results from experimental studies on wood fires in a laboratory-scale tunnel network. Experimental measurements include ignition delay time, flame spread rate, ventilation air and gas flow rates, wood temperature, gas temperature, pressure and composition, thermal flux, and smoke particulates. These measurements form a data base for fire-scaling studies and provide information on various fire processes, such as flow interaction between ventilation air and fire, fire throttling and reverse flow, and duct fire energetics. Results show how hazards of duct fires relate to the development of (1) asphyxiating and toxic fumes, (2) explosive gas mixtures, (3) throttling of ventilation air, and (4) high-temperature combustion products. Such fire hazards should be carefully considered when testing flammabilities of materials used in a confined underground mine environment.

Jan 1, 1980

By Rimas Pakalnis, Doug Milne, Marc Ruest, Lewis Martin

Whereas many researchers and mine engineers have conducted tests on cable bolts using various grouts, water: cement ratios, and physical modifications of the cable to determine the load-carrying characteristics ofa bolt, few studies have been conducted on cable bolts fitted with internal instruments. Those studies that have been done have concentrated on cable response averaged over significant (6.1 m) cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed. A numerical analysis was performed to match laboratory results. Loads calculated by the model were then compared to loads measured in the laboratory on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. This paper documents test results on these modified cable bolts. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over long cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable. The instrument has been successfully field tested at FMC's Granger Mine, Granger, WY; the Meikle Mine, Carlin, NV; the Stillwater Mine, Nye, MT; and the Getchell Mine, Golconda, NV. By monitoring load and displacement of the rock mass using these instrumented bolts, more-effective ground support can be selected and installed, which will lead to safer working conditions for miners.

Jan 4, 2004

By R. W. Freedman

The gas chromatographic method, devised by the Bureau of Mines for analyzing routine mine air samples, was compared with the infrared method used for confirmatory determination of methane in mine air. While maintaining the specificity of the infrared method for methane determination, the gas chromatographic method is more precise, much more rapidly performed, and more convenient.

Jan 1, 1968

By J. B. Gayle

The merits of the various methods for dry-quenching coke have been the subject of numerous publications and almost equally numerous controversies for the past 40 years.5/ Most investigators have concluded that dry quenching is advantageous. Some have based their arguments on the improved physical properties of the resultant cokes. Others have claimed little or no improvement and have based their arguments on the economies acquired from the recovery and utilization of sensible heat. The extent to which the method of quenching influences the properties of the resultant cokes is of importance in connection with the operation of both commercial and experimental ovens. On the other hand, the recovery and utilization of sensible heat are economic problems related solely to commercial oven operation and- depend on the method of dry quenching used and the demand for a low intensity energy source. The scope of the present Bureau of Mines investigation has been limited to a comparative study of the properties of wet- and dry-quenched cokes produced from six coals and blends carbonized at flue temperatures of 2, 000° and 2,400° F. in the Tuscaloosa oven.

Jan 1, 1959

By M. G. Zabetakis

At ordinary temperatures and pressures methyl ethyl ketone (MEK)-air mixtures containing between 2.0 and 11 vol.-pct. MEK and methyl isobutyl ketone (MIBK)-air mixtures containing between 1.5 and 7.5 vol.-pct. MIBK are flammable. However, MEK-bromochloromethane (BCM)-air mixtures containing at least 6.2 vol.-pct. BCM and MIBK-BCM-air mixtures containing at least 7.0 vol.-pct. BCM are nonflammable. Also, MEK-BCM-air and MIBK-BCM-air mixtures containing less than 18.7 vol.-pct. oxygen are nonflammable. To assure the formation of nonflammable mixtures when mixed with air, MEK-BCM vapor mixtures must contain at least 1.6 vol. BCM per volume MEK, and MIBK-BCM vapor mixtures must contain at least 2.8 vol. BCM per volume of MIBK; these quantities of BCM would be produced by liquid mixtures containing 55 vol.-pct. BCM in the first case and 60 vol.-pct. in the second. An MIBK-BCM-trimethylene chlorobromide mixture containing equal volumes of each liquid forms nonflammable mixtures with air at ordinary temperatures and pressures. The same is true of a liquid mixture containing 34.6 pct. (liquid volume) BCM, 34.b pct. perchloroethylene, 15.4 pct. MIBK, 7.7 pct. toluene, 3.85 pct. ethyl amyl ketone, and 3.85 pct. trimethylene bromide.

Jan 1, 1960

By D. S. Kingery

The data obtained from this study cover test areas that are gassy to ultragassy and pillared areas of different sizes and degrees of tightness. The methods of controlling ventilation, applying bleeders, and supporting bleeder entries varied in the different test areas. It was not possible to study all conditions likely to be encountered in coal mines. Undoubtedly, there are areas where bleeder entries, even though properly planned and maintained, might prove unsatisfactory. However, on the basis of this study, the following observations were made: 1. Tests showed that each bleeder system studied provided some movement of air through the pillared area; the quantities of air delivered to the pillar line, ranged from 23 to 82 percent, depending mainly on the extent to which bleeder re-turns were used as main returns from the section. 2. Pressure measurements taken across pillared areas showed maximum pressure drops ranging from 0.05 inch of water for a shallow gob to 2.69 inches for a very deep gob. The pressure differentials varied with the size and tightness of the gob but proved adequate to induce airflow across worked-out areas or through fringes of the gob to the bleeder return system.

Jan 1, 1957

By William Cochran

Data on the cost and quantity available were developed for rutile (TiO2), which is potentially recoverable as a byproduct at sand-washing plants in the Southeastern States of Alabama, Georgia, North Carolina, and South Carolina. Baaed on 1969 production data, an estimated 4,300 tons of rutile could be recovered annually from plants that process more than 25,000 tons of sand per year. Rutile prices at which this resource would be available ranged upward from $262 per ton, compared with the current market value of $185 per ton.

Jan 1, 1972

By W. S. Anderson

The use of flexible liners for support of underground openings has been investigated by the Bureau of Mines. This report presents installation procedures and instrumentation results of a full-scale flexible liner field installation in the Burgin mine. The flexible liner is a part of the mine support system and has provided maintenance-free support for 22 months

Jan 1, 1975

By Peter H. Toepfer

Hydraulically emplaced, classified mill sands long have been used for stope fill. Entrained water drains rapidly from this type of fill through openings between the sand grains. Slimes are removed to facilitate drainage of the water, thereby lowering dangerous hydrostatic pressures in the fill. Use of unclassified mill tailing as practiced at the Dayrock mine is a recent development and represents a fundamentally different approach to the problems of inhibiting the development of hydrostatic pressures within the stope fill. At the. Dayrock mine, mill tailing is used to form a densely packed fill of sand and slime particles relatively impervious to additional water.

Jan 1, 1952

By Larry G. Stolarczyk

1.0 FRAMEWORK FOR COMPARISON This document describes the decision factors that bear on the selection of the modulation process for the wireless underground medium frequency (MF) communication system. The selected modulation process must satisfy the Bureau of Mines stated objective of improving general communications within an underground mine. The improvement being sought includes the development of a wireless communication technology of measurable benefit to both mine safety and mine productivity. The improvement will allow wireless communications paths to exist between roving miners. The wireless communication paths will also be made compatible with the existing underground telephone system to extend paging and voice communication throughout the underground mine. The new wireless equipment will include man-pack, vehicular, repeater, and base station transceivers. Repeaters and base stations will feature coupling networks for interfacing with the existing telephone circuits. Frequency modulation (FM) and single sideband (SSB) modulation processes are analyzed in view of the special conditions associated with underground mining. Of primary importance is the tremendous electrical noise generated in an operating mine that could adversely affect communications quality. High noise coupled with high attenuation rate of near field signals forces the communication system to be inherently short range. Fortunately, near field signals can propagate over great distances on underground wires and cables. The framework for comparison is generated by presenting all factors that

By K. D. Plants, J. H. Holden, L. F. Willmott

Pulverized high- volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure - gasification pilot plant equipped for steampickup feeding . The pilot plant operated satisfactorily at relatively high steam- to - coal ratios , but steam- to - coal ratios could not be reduced much below 0.5 lb / lb without condensation of steam or softening of the coal . Carbon gasified , gas composition , and coal and oxygen requirements were essentially the same as for a pilot plant equipped with a fluidized coal feeder . Average results from the pilot plant equipped for steam- pickup feeding were coal requirement , 37.3 lb/M ( 1,000 ) scf of CO + H₂ produced ; oxygen requirement , 358 scf /M scf CO + H₂ produced ; and carbon gasified , 87.7 percent .

Jan 1, 1964

By J. M. Gomes

The Bureau of Mines has investigated the occurrence and recovery of by-product heavy minerals from sand and gravel operations as a means of assessing the Nation's resources. Sand samples from 63 locations in central and southern California were treated to yield heavy-mineral concentrates. The mineral compositions of the concentrates were characterized by chemical and mineralogical examinations. Additional large quantities of concentrates were prepared from selected deposits that contained significant quantities. Beneficiation studies were performed on these concentrates to recover individual mineral products. Gold was recovered by amalgamation; platinum-group metals and radioactive minerals by flotation; magnetite, ilmenite, and chromite by magnetic and high-tension separation techniques.

Jan 1, 1980

By Vijia K. Karra, John J. Sammarco, Robert Paddock, Edward F. Fries

Workers in hazardous environments such as mining are constantly exposed to the health and safety hazards of dynamic and unpredictable conditions. One approach to enable them to manage these hazards is to provide them with situational awareness: real-time data (environ-mental, physiological, and physical location data) obtained from wireless, wearable, smart sensor technologies deployed at the work area. The scope of this approach is limited to managing the hazards of the immediate work area for prevention purposes; it does not include technologies needed after a disaster. Three critical technologies emerge and converge to support this technical approach: smart-wearable sensors, wireless sensor networks, and low-power embedded computing. The major focus of this report is on smart sensors and wireless sensor networks. Wireless networks form the infrastructure to support the realization of situational awareness; therefore, there is a significant focus on wireless networks. Lastly, the “Future Research” section pulls together the three critical technologies by proposing applications that are relevant to mining. The applications are injured miner (person-down) detection; a wireless, wearable remote viewer; and an ultrawide band smart environment that enables localization and tracking of humans and resources. The smart environment could provide location data, physiological data, and communications (video, photos, graphical images, audio, and text messages).

Jan 4, 2007

By J. J. Demeter

As part of its work on converting coal to fluid fuels, the Federal Bureau of Mines has been studying the synthesis of liquid fuels from carbon monoxide and hydrogen by Fischer-Tropsch synthesis. A fluidized bed of nitrided, fused-iron catalyst has been operated successfully to produce high yields of oxygenated compounds. Trouble-free operation continued for over 800 hours, and the test was terminated voluntarily. About 85 percent of the fresh feed was converted when the unit was operated at a space velocity of 500 hr.-1, a 12:1 recycle-to-fresh-feed-gas ratio, a 300-p. s. i. g. pressure, and a temperature of 252° C. When operating at a fresh-feed-gas space velocity of 1,000 hr.-l and a 9:1 ratio of recycle to fresh gas, conversion of fresh feed was 68 percent, and the product yield was 235.9 grams per cubic meter of synthesis gas converted. The oxygenate and C5 and heavier hydrocarbon yield was 110.6 grams per cubic meter of gas converted, 83 percent of this was oxygenates. The atom ratio of N:Fe of the catalyst, initially 0.455, decreased to 0.288 by the end of the 800-hour experiment. Nevertheless, the yield of oxygenated compounds per cubic meter of H2 + CO converted at the end of the run was approximately the same as that obtained 500 hours earlier with identical operating conditions. X-ray analysis of the discharged catalyst indicated that only ?-iron carbonitride was present. Sieve analysis of the discharged catalyst indicated that only 2 percent of fines was produced during the reduction, nitriding, and synthesis.

Jan 1, 1959

By Donald N. H. Chi

The unsteady, one-dimensional, compressible-flow equations have been solved numerically for a deflagration propagating through a gallery of finite length closed at the ignition end and open at the opposite end. These equations were solved for two situations wherein (1) the propagating flame was extinguished after 0.1 sec or before the return of aerodynamic disturbances reflected from the open end, and (2) the flame was allowed to propagate a full 0.8 sec until it was extinguished. It was found that the process of sudden flame extinguishment creates rarefaction waves that, upon entering the burned zone, produce resonance within the burned cavity. For the relatively small value of the product of the expansion ratio (8.5) and the effective burning velocities of 7.4 m sec-1 for the first experiment and 4.9 m sec-1 for the second experiment, it was found that the acoustic approximation provides an adequate estimate of the pressures developed ahead of the flame during the system's early history.

Jan 1, 1974

By M. A. Hammer

In this study by the Federal Bureau of Mines Pennsylvania anthracite from the Eastern Middle field was oxidized by concentrated nitric acid at steam-bath temperature for 24 to 1,000 hours. The quantitative data obtained include yields of nitric-acid soluble and insoluble products and the distribution of carbon and ash in each. The acid-insoluble residues were examined for solubility in aqueous sodium hydroxide. With a sodium hydroxide concentration of at least 1 normal, a portion of the residue could be extracted in the form of a true solution. With lower alkali concentrations, peptization occurred. Alkali solubility of the residue increased with length of oxidation. However, when expressed in percentages of original coal weight, the alkali solubility remained essentially constant after 192 hours of oxidation. This suggests that the alkali-soluble products are converted to acid-soluble products at the same rate as the original coal substance is converted to alkali-soluble material. Microscopic observations of the peptization of the acid-insoluble residues revealed a gross micellar physical structure. The action of nitric acid is apparently not restricted to the surface of a coal particle. The acid penetrates the particle through the pore structure, dissolving some of the ash and altering the bonds between the coal micelles. The bond alteration, as indicated by ultimate analyses, involves the physical and chemical adsorption of the components of nitric acid. Some of the altered bonds are not thermally stable; this instability is shown by the complete loss of peptizing ability when the acid-insoluble products are heated above 200° C. This loss is accompanied by the evolution of water, oxides of nitrogen, and hydrocyanic acid.

Jan 1, 1961