Search Documents

By H. Kim, R. W. Plummer, T. J. Stobbe, W. G. Jones

"Exposure to airborne dust in coal mines has caused respiratory disease in coal miners. The causal agent in these diseases remains unknown, although the minerals found in and around the coal seam have been implicated. Toxicological studies designed to establish the effect of different mineral combinations and concentrations are lacking because the mineral content of coal mine dust has not been defined. This paper reports the initial results of a study done to characterize the mineral content of the coal mine dust found in a mine in the Upper Freepott seam in Northern West Virginia. Coal mine dust samples were collected using 4- stage cassette impactors at nine locations in the mine. The samples were analyzed by an x-ray microdiffraction film technique supplemented by energy dispersive scanning electron microscopy. Primary size modes of about 17 to 20 micrometers from the samples collected at the haulageway and the returnside of the continuous miner were found. From the returnside of the roof bolter samples, a primary size mode of 12to15 micrometers was measured. The minerals found in high percentages were illite, kaolinite, quartz, and calcite. The distribution of minerals in inter· and intra- location samples showed wide variations. Trends in these variations are presented. Stobbe, T. J.; Plummer, R. W.; Kim, H.; Jones. W.: Characterization of coal mine dust. Appl. Ind. Hyg. 2:95· 100; 1986. IntroductionDisease-associated dusts in coal mine environments continue to afflict miners in today's modern mines. The relationship between exposure to coal mine dust and the development of various respiratory diseases has been well recognized; however, the reasons for variation in occurrence of these diseases among miners in different geographic areas,(1) rank of coal seams,(2-3) and jobs (4) remain uncertain. Several papers have reported on the causal agent in the development of these diseases. Davis (5) found that the percentage of the non-coal minerals present in the lungs of deceased miners increased as the level oi pneumoconiosis became more severe. Reisner (6) reported that cell damage caused by coal mine dust increases with the mineral and quartz content of the dust and with the geo· logical age and rank of the coals. Two studies, investigating the in vitro effects of mineral dusts. reported by Seemayer and Manojlovic (7) also obtained positive correlation between cytotoxicity and the mineral content of coal mine dust. Gormly (8) postulated that destruction of macrophages by certain mineral dusts is the first step in the development of pneumoconiosis. In 1980, Adamis and Timar (9) reported that quartz. sandstone, slate. respirable colliery dust. bentonite, illite, and some kaolins had cytotoxic effects on rat peritoneal macrophages""in vitro."" Walton,(10) however, reported that the presence of high clay, illite, and kaolin mineral exposures reversed the hazards associated with increasing quartz exposures. This finding was supported by Le Bouffant and coworkers.(11) They reported that illite present in coal mine dust strongly inhibited the pathogenic effects of quartz while kaolin had a weaker inhibitory effect."

Mar 1, 1989

By P. S. Jacobsen

In 1960 over 93 percent of the coal cleaned mechanically in the United States was cleaned in processes that utilized water or dense-medium suspensions of fine solids in water. Thus, in the process of removing deleterious ash-forming and sulfur-bearing minerals, another deleterious substance--water-- is added to the coal. The subsequent removal of the water from the coal, and the concomitant recovery of the coal from the water, is not troublesome in the sizes coarser than 1/4-inch. In the finer sizes, however, it is a difficult procedure that often costs more than the original washing operation. Because of the importance of liquid-solids separation in coal preparation, the Bureau of Mines has a continuing program of research in this field. The objective is to make available information on the performance characteristics of various types of equipment available for liquid-solids separations, thus promoting the wise selection of equipment for specific applications, and, thereby, more effective processing of coal. Results of work on flocculation as an aid to filtration5 and the sieve bend screen6 have been published. The present investigation of the screw-type classifier operating in combination with the cyclone was undertaken primarily because such classifiers are comparatively new to coal preparation and information on their performance is not available. The cyclone has become well-known since its introduction in this country by the Bureau of Mines in 1948.7 Use of the cyclone in conjunction with the screw-type classifier represents an attempt to provide the maximum recovery of solids at minimum moisture content.

Jan 1, 1962

By C. R. Bopp, N. A. C. Smith

"For a period of several years, beginning with 1915, there has been a continuous change in the quality of motor gasoline. The average volatility has decreased, this to the fact that higher boiling fractions of the crude oil have been included in the gasoline. This change in quality was made necessary by the tremendous increase in the demand for motor fuel, caused by the development of the motor car, and during the war was an absolute necessity to avoid gasoline shortages. The Bureau of Mines has kept in close touch with this situation by making surveys from time to time of the gasolines sold throughout the country, as this information is of value to manufacturers and users of motor cars and also indicates when any changes are required in the Government specifications. The Bureau has just completed a gasoline survey and is in a position to make public the fact that there has been very little change in the quality of motor gasoline in recent months.During the period from January 17 to February 3, 1920, 81 samples of actor gasoline were collected by representatives of the Bureau of Mines in seven districts of the United States. The cities selected for this survey were New York, N. Y., including Brooklyn; Washington, D. C.; Pittsburgh, Pa.; Chicago, Ill.; New Orleans, La.; Salt Lake City, Utah; and San Francisco, Cal., including Berkeley. In every case the samples collected were taken in such a manner as to represent material actually being sold as motor fuel, and to include samples from each refinery marketing in the district."

Jan 1, 1920

By Bruce Maxwell

The deformation modulus of coal mine pillars theoretically can be reduced by drilling holes in advance of the mining face. This reduction of modulus along the edge of the pillar has the effect of decreasing the stress concentration in the roof; control of roof caving is thereby predicted. Initial field work indicated that a high horizontal stress field existed at the field test site: Subsequent field work was undertaken to confirm the high horizontal stress field and to attempt to relieve the horizontal stress in the immediate roof. A method of softening pillars in conjunction with normal mining activity was developed. Instruments to measure horizontal roof strain, roof parting, roof tilt at the rib, and changes in vertical and horizontal stress in the roof and in the coal were used. These instruments were installed in both softened and unsoftened entries and in locations to indicate the effect of vertical slots in the roof. Significant stress reduction due to pillar softening was indicated, but the effect of this reduction on roof stability was not established. The vertical roof slots relieved the horizontal stress in the immediate roof very effectively, and observations of roof conditions indicated that the slots definitely improved roof stability.

Jan 1, 1977

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some diamond drilling at the Almedia deposit In an endeavor to find an additional source of supply of lead and zinc. It is reported that in 1816, lead and zinc minerals were found in the limestone quarries near the boundary line between Scott and Center townships. In an attempt to develop these minerals in paying quantities, an alit was driven for several rods into a bluff Just west of the present Almedia mine, This is believed to be the Web mine, mentioned briefly by Parker Cleaveland in 1816. In 1901 the Almedia mine was developed by an open cut and three shafts. The hoisting shaft at the time of drilling by the Bureau of Mines was sounded to a depth of 115 feet. A concentrating plant reportedly made shipments to Hamburg, Germany, for reduction. The deposit is in a somewhat slaty limestone. The ore occurs in a northeast fracture zone along the strike of the limestone and dips to the southeast. Old miners state that the ore appeared as large chunks of galena and sphalerite. In 1949, to investigate the downward extension of the oreshoot, the Bureau of Mines drilled four holes aggregating 1,126.3 feet.

Jan 1, 1950

By Todd M. Ruff

Blind areas around construction equipment are a major contributing factor in incidents involving a piece of equipment striking a worker. In highway construction, these types of incidents result in an average of 22 deaths a year in the United States. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these incidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers or other objects. Several camera and sensor systems are available for this application. These systems were evaluated on various trucks used in road construction and maintenance. Tests were conducted on sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted on dump trucks and utility vehicles during the warmer months to study the effectiveness of the systems in highway work zones. Results showed that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in congested work areas.

By David C. Oyler

The U.S. Bureau of Mines and the United States Steel Corporation evaluated the progress of methane drainage at the Oak Grove, AL, degasification pattern. Coalbed pressures were monitored between December 1981 and November 1985. Formation pressures, in the lower bench of the Mary Lee Coalbed, were reduced from 400 lbf/in2(ga) in 1977 to 50 lbf/in2(ga) in November 1985. Gas contents of coal cores obtained from monitor wells were compared with coalbed gas contents measured in 1976. Data indicated a 48- to 56-pct reduction within the pattern and a 29-pct reduction at a point 500 ft outside the pattern. The effect of the advance of a section of the Oak Grove Mine on changes in gas and water production rates in the pattern was evaluated. Gas production increases were noted in 12 wells; water production decreases were noted in 6. The times of initial influence indicate the presence of a zone of high permeability within the pattern. This zone correlates well in orientation and location with a fracture zone mined through at the mine. The existence of such fracture zones could have a significant effect on productivity of individual coalbed methane wells.

Jan 1, 1989

"The dust/lung research of the Center has several long-range objectives:* better methods for the early diagnosis of coal workers' pneumoconiosis (CWP);* methods to modify the disease process;* tests to identify toxic products; and* tests to identify individuals with heightened susceptibility to pneumoconiosis.A major immediate objective is to define the mechanism of dust-induced lung disease. This means determining:* dust characteristics that are important in causing lung diseases;* important interactions between dust and lungs; and* earliest detectable stages of the disease.Several of the Center's projects involve exposing lung cells in culture (in vitro) or animal lungs (in vivo) to samples of the suite of characterized mineral dusts described earlier. The responses of the lung cells or tissues to the dusts are being studied in order to better understand how inhaled dusts cause lung disease.One project is studying the effect of dust exposure on the production of mucus by rat tracheal explants in vitro. Mucus is a major factor in clearing inorganic dusts from the lung. Results thus far have shown that exposure of tracheal cultures to coal dust caused a decrease in micin production in comparison to parallel cultures without dust. To examine the effect of in vivo coal dust exposure, rats were maintained in an inhalation chamber for two weeks, and control rats were in an identical, but dust-free chamber. Tracheal explants results indicate that the effect of in vivo dust exposure is similar to that noted in the in vitro experiments.Pulmonary alveolar macrophages (PAMs) are a key component of the lung's response to inhaled particulates, and they play several important roles in pulmonary inflammatory and repair processes. PAMs are the cells that actually ingest dust particles. Other studies have shown that they play a critical role in the development of silicosis and asbestosis. The Center is studying the effect of dust exposure on the release of oxygen free radicals (superoxide) by PAMs. Intercellular production of superoxide occurs when PAMs phagocytize particles, such as inhaled bacteria, and is an essential mechanism by which PAMs kill ingested, bacteria. A number of complex physiological events occur during this process which are not clearly understood. It is thought that PAMs containing indigestible materials, such as mineral dusts, overproduce superoxide, or inappropriately release it into the surrounding tissues. If true, this would cause toxicity to surrounding lung cells by peroxidation of the lipids in the cell membranes. In vitro exposure of PAMs to low or high doses of kaolin is inert. Preliminary studies indicate that coating the quartz particles with a surfactant reduces toxicity."

Nov 1, 1988

By H. S. Auvil, J. T. McCartney, J. D. Davis

"INTRODUCTION It is now generally recognized that the small-scale laboratory dilatometer method of test does not give results of much utility in predicting the expansion (or contraction) of a coal in a coke oven. The carbonizing conditions in the laboratory test differ radically from those in the oven; in this test, the charge is heated through the coking range of temperature as a whole, whereas in the oven, coking proceeds by layers parallel to the oven walls as each succeeding portion of the charge goes through the plastic range of temperature and coke formation sets in. The paths of the gases and vapors and the pressures set up are different in the two methods. Furthermore, the rate of heating in the test usually is much more rapid than in the oven. H. Koppers 5/ was perhaps the first to adopt apparatus and procedure whereby the layer coking of the coke oven could be simulated closely however, the heating progressed from one side of the charge only; later he experimented with a small coke oven with a movable wall heated from both sides. It is not clear how well the results in the later oven correlated with those of the earlier small test oven, but in a comparatively recent Koppers publication a modification of the original small test oven heated from one side is recommended 6/ Altieri 7/ was perhaps the first to experiment with the Koppers type small test oven in the United States and Brown- has tested a large variety of coals in a rectangular test oven of his own design heated from the sole or floor. Subcommittee XV of American Society for Testing Materials Committee D-5 is now making a study of the various methods proposed for determination of expanding and plastic properties of coal with a view to standardization. 9/"

May 1, 1939

By M. A. Elliott

Diesel-powered haulage equipment has recently been tested and approved for permissibility by the Bureau of Mines for use in mining in the United States. Achievement of this advance in safety involved extensive studies, both in the testing station (2, 3, 20, 21, 22, 23, 24, 25, 26, 27)3/ and in the field 1, 4, 13, 30), of the operating characteristics of diesel engines in relation to the toe of such engines underground. The results of these studies formed the basis for establishing the requirements that should be met by diesel-powered haulage equipment approved for permissibility. Considerable interest has been manifested in the development of diesel-powered haulage equipment fur mines. The purpose of this paper is to retrace briefly the course of this development and to answer such questions as: What is the history of the use of diesel engines underground? Why has the Bureau of Mines been interested in the development of diesel-powered haulage equipment for use in mines?

Jan 1, 1953

By R. V. Higgins

In a recent report3/ the authors presented a rapid method of calculating, by means of a desk calculator, the future performance of oil reservoirs in which the motivating agent was gas. The accuracy of the method was tested by data obtained from an electronic computer. Because of the accuracy obtained for the limited number of calculations performed, considerable interest has been expressed in the electronic computer program used to obtain the comparative data by an analytical solution. Accordingly, the computer procedures for the analytical solution are presented in this report. In an earlier report, 4/ a reservoir appraisal procedure was published in which an iterative method was used. Many requests were received for the computer program used to obtain the values given in that paper. That program, with some modifications, also is presented in this report. The modifications are given because of the progress that his been made in computers, and because much of the program for the analytical solution is usable for the iterative procedure.

Jan 1, 1960

By N. E. Hanna

Experience with the current version of gallery test 4, in use since 1913 to evaluate the incendivity of permissible explosives in the presence of coal dust, has shown the procedure to have inadequate discrimination. Consequently the Bureau of Mines used the up-and-down method of statistical design to investigate the incendivity of permissible explosives in the presence of coal dust and gas. A suitable device was developed to measure coal dust concentrations in the air-gas mixtures and to disperse the dust in the gallery atmosphere. A proposed testing method which uses suspended shots in a predispersed coal dust-gas-air mixture was evaluated. The new method can discriminate between different explosives with respect to their incendivity. Maximum ignitibility of the coal dust cloud by permissible explosives occurred in the vicinity of 0.3 oz/cu ft. About 10% sodium chloride in permissible explosive formulations had a very significant effect in reducing the probability of igniting coal dust. Bundled charges were more incendive than column charges.

Jan 1, 1966

By G. G. Morgis, J. J. Forbes

"INTRODUCTION The greatly diversified and increased uses of beryllium and its con& pounds in recent years have focused attention on the health hazards incident thereto. The Bureau of Mines has a fundamental interest in safety and the elimination or reduction of health hazards in the mineral and allied industries, and it recognizes that serious hazards are inherent in the production and use of beryllium and its compounds. This circular presents a review of the literature pertaining to such health hazards but does not describe original research by Bureau personnel. Most of the bibliography has boon either quoted in part or abstracted in an effort to present information in a comprehensive and readable form.In reviewing the literature, differences of opinions wore recognized in the writings of the respective authors, but no attempt was made to evaluate such differences. This presentation was devoted strictly to reporting without editorial comment.SUMMARYAlthough beryllium was known to industry for about 150 years, its toxicity did not present any serious problems in the United States until the advent of World War II, when the increased use of this element and its compounds brought to light several toxicologic reactions occurring primarily in the lungs and skin of workers handling it. The pulmonary effects, characterized as acute pnoumonitis and chronic pulmonary granulomatosis in beryllium workers, are far more serious than the dermatological manifestations.The addition of beryllium to the list of toxic industrial metals has boon so recent that there is still some confusion in the clinical picture. Data on magnitudes of exposure likely to be responsible for the production of disease are not yet adequate. There appears to be no relation between the severity of exposure and the development of cases some of those having had severe exposure have not developed a reaction, whereas those having a slight exposure in some instances have developed a response."

Jul 1, 1950

West Virginia ranks second in the nation in coal production, surpassed only by Wyoming, and usually accounts for 15 to 20percent of the nation's total annual production. Cod occurs in seams of minable thickness in all but nine of the state's 55 counties. There are two coal- producing regions, the northern field and the southern field. West Virginia coal is mined by both underground and surface methods. Underground mines in West Virginia account for a major portion of its coal production. Surface mines are generally contour operations and, especially in the southern field, are in steep slope areas, with slopes greater than 20 degrees. Many of the surface mines remove multiple seams. Recoverable reserves in West Virginia total in excess of 55 billion tons of bituminous coal. West Virginia's regulatory program was conditionally approved on January 19, 198 1. Its Abandoned Mine Land Program was approved February 23,198 1, with emergency authority granted on August 26,1988.

Jan 1, 1992

By Charles L. Kimbell

Available statistics on 1989 worldwide consumption of selected nonfuel minerals shown in table 5 show increases for 11 of 14 listed nonfuel mineral commodities with 1 unchanged from the 1988 level, a departure from the pattern of the past 2 years, in which each of the listed commodities registered gains. The 1989 results, however, were better than those for 1986 when only seven listed nonfuel mineral commodities recorded gains with one un- changed from 1985. Consumption of the two ferrous metal raw materials listed advanced as functions of increased output of pig iron and crude steel. The increase in iron ore consumption exceeded the increase in iron ore output, suggesting a slight drawdown of world iron ore inventories. The estimated in- crease in iron and steel scrap consumption was slightly greater than the minuscule increase in world steel production, but it is believed that there was little change in the ratio of iron ore to scrap in steel plant feed on a global basis.

Jan 1, 1992

By J. Fletcher Smoak

Consumption of abrasive materials in the United States in 1981 was approximately $340 million, of which 37 % was industrial diamond (natural and synthetic), 39% manufactured abrasives, and 24% natural abrasives. Production and shipments of natural abrasives, excluding emery and industrial diamond, decreased in quantity 9% and 7%, respectively, when compared with that of 1980. Emery showed the largest change in output, decreasing 30% in quantity and 20% in value. Production of nonmetallic .manufactured abrasives material plus shipments of metallic abrasives material decreased 5% in quantity but increased 4% in value. Nonmetallic manufactured abrasives consisted of aluminum oxide (fused) and crude silicon carbide produced in the United States and Canada and accounted for 63% of the value of all manufactured abrasives. Metallic abrasives shipments included chilled and annealed iron shot and grit, steel shot and grit, plus cut wire, aluminum, and stainless steel shot and equaled 37 % of the value of all manufactured abrasives.

Jan 1, 1982

By Bruce I. Thomas

In 1943, the Bureau of Mines investigated the occurrence of cassiterite in the gravels of Morelock Creek which flows into the Yukon River 32 miles east of the confluence of the Yukon and Tanana Rivers in central Alaska. Samples of the gravels were obtained by churn drilling test pitting, shaft sinking, and open-cut mining. The gravels along Morelock Creek are about 6 feet in depth and covered with about 2-1/2 feet of overburden. The overburden is frozen, but the underlying gravels are not. Cassiterite, with gold and other heavy minerals, is usually concentrated in the first 2 feet of' gravel above bedrock and in some places penetrates into joint planes in the bedrock. The various methods of obtaining samples are discussed, and drill logs and analyses are tabulated in this report.

Jan 1, 1948

By Fred N. Kissell

Tracer gas decay curves were experimentally obtained in a full-scale model coal mine working face area. The concentration of tracer gas was found to decay in exponential fashion but with a change in slope. This change in slope is attributed to eddy zones in the face area. A simple theory was developed that allows one to calculate the approximate amount of gas in the eddy zones and thus estimate the size of the eddy zones.

Jan 1, 1974

By Harry Dobroski, Larry G. Stolarczyk

Medium-frequency (MF) techniques have been successfully .[pplied] to the problem of radio voice communications in both coal and metal and nonmental mines. Long range is achieved by taking advantage of existing mine conductors that carry and propagate the signal over vast areas. It is very likely that in the near future such systems will become the referred method for general mine communications. MF techniques can also be applied to the areas of in-mine control and monitoring. Preliminary work in this area is described. In a western mine, locomotives are being operated under MF remote control in a loading operation. In several eastern mines, MF has been evaluated as a method for monitoring the status of devices in remote areas of the mines. All control and monitor information uses existing mine conductors.

Pillars with width-to-height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars, fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented that illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.