Search Documents

By C. C. Shale

Electrical resistivities for various coal ashes in air and in a nitrogen atmosphere are given over the range 100° to 1,500° F. Resistivity of low-carbon ash in air is very high at low temperature, rises to a maximum at about 250° F, decreases very rapidly with increasing temperature to about 800° F, then decreases gradually to approach an asymptote at 1,500° F. Resistivity of high-carbon ash in air follows this same general trend at values which are much lower and are proportional to the carbon content. After the carbon has been burned off, resistivity of the remaining ash approaches the high values corresponding to low-carbon ash of similar chemistry. Two factorial experiments show the effects of temperature, particle size, chemical content, and compressibility on the resistivities of four fly ashes of widely different chemical composition in the temperature range proposed for coal-fired turbines. Resistivities of all low-carbon ashes tested fall in the range 106 to 107 ohm cm at 1,500° F and should be removable by electrostatic precipitators. Ashes containing carbon in excess of about 8 percent, however, have low resistivity (as determined in nitrogen), especially at high temperatures. Therefore, high-carbon materials may not be collectable in precipitators because the resistivity is below the minimum value necessary for precipitation. Consequently, high carbon residues from partial combustion of coal probably could not be removed effectively at high temperatures.

Jan 1, 1968

By Lloyd A. Morley, Alan M. Christman

General Six open-pit metal mines, five copper and one molybdenum, were visited during the course of the research. Four were investigated twice, in summer and in winter, in order to determine the effects of seasonal variations In temperature and moisture upon the measured parameters, Permission to enter the fifth mine was received too late to make an examination during the summer months. The sixth mine was visited to confirm the results obtained from the other five and specifically, to observe how the project recommendations (as will be presented in this chapter) would apply to open-pit metal mines in general. Information gathered during the ten plant visits is sufficient to form an adequate data base for the report. A complete presentation of all field trip data is given in Appendix 1. Further, a detailed description of the electrical distribution and grounding practices at each mine is also contained there. Typical System. At a typical mine as shown schematically in Figure 62, one or more substations with resistance-grounded secondaries are employed to transform the incoming utility-voltage to the lower potential used by the mining machines, generally three-phase 4160 V. At this level, pit distribution is carried on overhead lines, supported by wooden poles, to supply switchhouses located in benches near the particular piece of equipment. A switchhouse is a small portable (often skid-mounted) structure at the termination of an overhead line which contains disconnect

Jan 1, 1976

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

9. Remote Sealing System Sensitivity 9. 1 Introduction In the previous sections a description of the overall system has been presented along with detailed descriptions of the equipment and techniques employed with the preliminary probing system, the seal em¬placement system and the seal checking system. In addition, the use of these subsystems in a specific mine application has been described in considerable detail. A broad range of parameters of interest was specified in the contract, as summarized in Section 1. 3. Most of these are a function of the general location; i. e. , the location of the mine, and the specific location; i. e. , the location of the boreholes. These parameters of interest include passage size, shape, depth, slope and water con¬ditions. The length, diameter and location of the boreholes within the mine passage and on the surface are critical parameters as well. A few additional parameters may affect one or more of the remote sealing subsystems. These include temperature, topography, rock and soil conditions, and underground water. While variation in these parameters will not render the system inoperative, consideration of them in the planning stages will simplify and expedite the field operation. In the following sections the effect of the various parameters on the remote sealing operation will be discussed. For clarity, the several tasks, borehole drilling and casing, preliminary probing, fly ash delivery, foam topping and seal checking, will each be considered separately.

Jan 1, 1973

By F. L. Klinger

CRUDE OIL refining continued to be the foremost industry of Bahrain in 1963. This island, the largest of a group 30 kilometers off the Saudi Arabian coast, is the site of the first petroleum discovery in the Persian Gulf and in the Arabian peninsular region. The island's only oilfield was discovered in 1932; exports of crude began in 1934 and the refinery was built in 1936. Although its crude oil has been less than 1 percent of annual Middle East output in recent years, Bahrain has been an important refining center for many years, processing a substantial portion of Saudi Arabian petroleum as well as all local production. The Bahrain refinery annually accounts for 17 percent 0 the petroleum products produced in the Middle East and 25 percent of the exports. Bahrain's mineral resources consist of oil, gas, and basic construction materials. Petroleum production and refining are the important mineral industries and contribute most of the national income by payments for taxes, wages, and local services including construction and material supply. The petroleum industry has supported a large share of local business and extensive indirect employment, and its early establishment also helped Bahrain to strengthen its position as a trading center in the Persian Gulf. The country's entrepôt trade produces about 20 percent of Government revenue, and Bahrain is somewhat less dependent on the petroleum industry than are the neighboring States to the west.

Jan 1, 1964

By F. B. Tough

An inusual job in controlling a gas well was executed on No. 1 well, Inland Oil and Refining Co., situated on the Alkali Butte structure, Freemont County, Wyoming. The work was done by the company in cooperation with the . S. Bureau of Minos, and resulted in a fuel saving of $5,000 in one season and of a repair job estimated at $15,000, or a total of $21,000. The woll had an open flow of 6,000,000 cubic feet of gas per day with a rock pressure of 560 pounds per square inch. A string of 6-1/4 inch casing with a toothed shoe was set on the cap rock above the gas sand at 2181 feet. Then the well was shut in, the gas worked out around both the 6-1/4 inch and 6-1/4 inch strings, breaking through the ground surface at several points under the derrick. Casing troubles encountered while drilling made it unsafe to attempt Coving the 6-1/4 inch string. Moreover, it was important from the standpoint of good management to make the gas from this well immediately available for fuel in other operations and, in addition, to save the gas from wasting. An ordinary mudding and cementing job would have necessitated sitting down this well for probably two months out of a very short operating season. For these rousons it was determined to mud the well, if possible, between the 6 and 8 inch strings by pumping mud fluid through the connection from the gas clamps. The gas clamps used wore of ordinary construction with a side outlet, making them equivalent to a Braden-hoad. When the mud fluid was pumped through the gas clamp into the space between the two strings, it began to appear inside the 6-1/4 inch string. It apparently entered the well either around the toothed shoe or through a "line sawed" leak in the string and was blown out of the well as fast as it was pumped in. In order to stop the leaks, about a half a gunny sack of finely chopped bull ropa was fed with the mud between the casings as before. The hemp gathered around the valves of the mud pump to some extent, and it also stuck in the casing-head fittings a few times. An obstruction in the casing- head would be removed by permitting the woll to "blow back" for a few seconds, and one in the pump valves, by removing the valves when necessary. In two days' time sufficient hemp and mud had been pumped into these strings to kill external and internal pressure. The wall was shut in and allowed to stand over night. The next day, by opening and closing the master gate at intervals,

Mar 1, 1921

The production of harmful pollutants from coal mines and/or from coal and associated strata has been a recognizable fact in the United States for over two hundred and seventy years. In 1698, Gabriel Thomas observed(l) that the colored water flowing from streams in this country was similar to that which flowed from the coal mines in Wales. Hence, water pollutants such as acid were being produced before any known coal mines were operating in this country. The coal mining industry has contributed to the increase of pollution by exposing large amounts of sulfide materials that enable the reaction of water, oxygen and sulfur containing materials to form acid. A map of the United States coal fields can be seen on Figure 1. The anthracite regions of Pennsylvania, although small when compared to the total reserves, have produced some of the country's major water problems. The map indicates the extent of bituminous reserves of the Appalachian and midwest regions. Also evident are the bituminous, subbituminous and lignite coal reserves in the west which have recently come into greater demand. Acid mine pollution is encountered in numerous states, but the major problem is found in the Ohio, Susquehanna, and Potomac River basins.(2) Most coal beds contain some sulfur which may be in the inorganic, sulfate, or sulfide form, and thus have the potential to produce sulfuric acid. However, much of the strata that overlays the coal beds also contains acid neutralizing materials. Therefore, the amount of acid produced depends upon the amount of both acid and alkali materials that dissolve in the water in any given mine. The common sources of sulfurous material in the seam or surrounding rock are generally called sulfur balls or "nigger heads" by the miners. Sulfur balls that have been observed(3) seem to be equally divided between those containing sulphuritic iron capable of producing sulfuric acid upon oxidation and those that are primarily calcium carbonate. It has been observed in many instances that two types of water, acid and alkaline, are being produced in the same mine. A study of the geological strata and a survey of subsidence, faults and sulfur balls will usually give some indication of why this happens. The reaction of pyrite (FeS2) with oxygen and water to form ferrous sulfate (FeSO4) and sulfuric acid (H2SO4) by a series of complex chemical interactions is well documented but not well understood.(4,5) However, it is well known that the reactions to form the acid cannot occur unless all three constituents are present. Since pyrite is inherent in most coal seams and air is needed to sustain the miner, the most logical answer is to eliminate water infiltration into the mine, or to remove it from the mine before acids can form.

Jan 1, 1970

By John L. Hill

"The Bureau of Mines is conducting research on the causes and methods for control of cutter roof failure in underground coal mines. This hazardous ground control problem exposes miners to the danger of falling roof rock and frequently results in massive roof failure. This report outlines the probable causes of cutter roof failure, which are proposed based on field investigations, numerical model analysis, and in-mine observations. Traditional methods of control are presented, as well as innovative methods based on mining concepts developed during earlier years of coal mining history. The report can be useful to a mine operator for assessing the causes of cutter roof failure on a site-by-site basis and for predicting the probability of its occurrence. A process is presented for selecting an optimum control method that includes both traditional and innovative control techniques for each of the various causes of cutter roof failure. INTRODUCTIONGround control research conducted by the Bureau of Mines is designed to develop technology that will aid in reducing the frequency of accidents associated with poor ground control conditions. Cutter roof failure often poses a safety hazard to miners and causes delays in production while massive roof falls are cleaned up and unstable roof is resupported. Implementation of control measures reduces the threat of injury to miners and prevents production delays.The definition of cutter roof failure used in this report separates this unique type of failure from other ground control problems, to aid in the analysis of the causes and in the development of control methods. The definition is as follows:Cutter roof failure in mine roof rock is a failure process that initially begins as a fracture plane in the roof rock parallel to, and located at, the roof-rib intersection. The fracture propagates upward into the roof over the mine opening at an angle usually steeper than 60° from the horizontal.The mappable extent of cutter failure may range in length from only a few feet to several hundred feet and may traverse entry-crosscut intersections without change in direction. Once initiated along the roof-rib line, a cutter may propagate away from the roof-rib line of one side of a room, cross the roof span, and continue along the other side of the room. It is important to note that this definition excludes a similar type of failure (sometimes referred to as ""kink roof') that has comparable characteristics but occurs in the center of the entry. (The reasons for this distinction are discussed in the ""Background"" section.) Researchers refer to the cutter failure discussed in this report as ""classic"" cutter roof failure; except for short deviations across intersections and entries, initial failure is confined to the roof-rib intersection."

Jan 1, 1986

By Donald F. Reed

Deposits of gray hematite occur in two districts in Talladega County, Ala., the Emauhee-Tallasechatch and Weewoka, both in the; vicinity of Wintorboro, 50 miles east of Birmingham. The deposits were investigated by the Bureau of Mines in 1945 and 1944. Approximately 15,000 feet of diamond drilling was done and 6,000 linear feet of trenches excavated and sampled.

Jan 1, 1949

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.

By S. H. Katz

"At the annual meeting of the International Association of Fire Engineers at Kansas City, Mo., in June, 1919, the Bureau of Mines offered to cooperate with municipal fire departments for the purpose of obtaining information regarding composition of the air in burning buildings. (Katz, S. H., Statement made at Convention of International Assoc. of Fire Engineers: Fire and Water Eng., vol. 66, July 16, 1919, pp. 129-30, also Fireman's Herald, vol. 78, July 12, 1919, pp. 48.) The gas-mask laboratory of the Bureau's experiment station at Pittsburgh sent vacuum bottles for taking samples to fire chiefs in twenty-five cities, who had signified their intention to aid in this work. It was hoped to obtain one hundred or more samples, because statistics in quantity are necessary for drawing reliable conclusions concern-in the likelihoods of encountering irrespirable as in burning buildings. This far, eleven samples have been received by the laboratory. Results of analyses and pertinent data regarding these samples are given in the accompanyingEight of the eleven samples contained, no carbon monoxide; seven of the eight were taken above the ground level and one below ground. One sample taken above ground contained 0.03 per cent carbon monoxide, and this quantity is not dangerous to breathe for a limited time. Of the three samples taken below ground, one contained no carbon monoxide; the other two contained 0.10 and, 0.35 per cent, respectively. This indicates that in a burning building, the hazard from carbon monoxide is much greater below the ground level. The cause undoubtedly lies in the poorer ventilation that is usually found in cellars or basements. Abundance of ventilation provides the necessary air for complete combustion, or if incomplete combustion does occur, the carbon monoxide generated by the fire is greatly diluted with fresh air and swept away by the current. It may be noted that the highest proportion of carbon monoxide was found in a cellar where a fire as burning among piled cases. The difficult access of air to the burning parts facilitated the formation and lib ration of carbon monoxide. The smoke here was very light and no difficulty was experienced in breathing. Some of the air containing dense smoke showed little change from normal air by analysis. Thus the density of smoke or the irritation and difficulty it causes in breathing are no indication of the presence of poisonous gas. None of the samples shows important oxygen."

Nov 1, 1920

The Technology Transfer Seminar on Mine Communications held on March 21-22, 1973, at the Pittsburgh Mining and Safety Research Center, Bruceton, Pa., presented information about recently developed equipment, instruments, and techniques for use in mine communications systems. All of the basic ideas presented in the fine seminar are operational in the Bureau of Mines Safety Research Mine in Bruceton.

Jan 1, 1974

By VAN. H. MANNING

During the nine years that have elapsed since the Bureau of Mines was established in 1910, the work of the bureau has included many investigations that have proved of high value to the Nation. Eleven mining experiment stations established by act of Congress have greatly increased the bureau's usefulness; being situated in the mining fields, these stations are closely in touch with industrial needs, and the results of their research and educational work are more directly available to those engaged in the mining, metallurgical, and mineral industries. In the United States mining is second in importance to agriculture only. The Federal Government annually appropriates large sums in the interest of agriculture, whereas the appropriations for mining are relatively small. But the nation-wide popularity of Government assistance to agriculture should not overshadow the need of Federal assistance to the mineral industry. With scientific management farms can be made to produce indefinitely without any depletion of the potential resources of the soil, but the mineral wealth of a country is a fixed quantity, and every year's production brings nearer its ulti- mate exhaustion. As the deposits of the richer or more readily available ores, espe- cially those in the West, have been depleted, development of methods for mining and treating the leaner or more inaccessible ores has lagged, so that meeting the increasing demands for certain metals is becoming more and more difficult. In some branches of mining the small inde- pendent operator is greatly handicapped. He has to rely on custom mills and smelters for the profit or loss of his product, and because of relatively inefficient methods of milling or smelting he may receive no return for much of the ore he mines. Even though the small operator thinks he knows of improved methods of obtaining the metals from the ores, he can not afford to install the necessary machinery or to carry on experiments that may or may not prove successful. In view of the increasing need of metals and the impossibility of renewing the ore supplies, efforts should be directed toward developing the most economical and efficient methods in mining and metal- lurgy. The great mining companies carry on independent research work, some of them on a large scale; but as such work is usually undertaken for gainful purposes, these companies do not feel under any obligation to give the results of their investigations to the world. Clearly the solution of the difficulty is to place in the mining districts trained mining and metallurgical engineers who will investigate and solve the problems for the benefit of the whole industry. It is with this purpose in view that experiment stations of the Bureau of Mines have been established to investigate economy, efficiency, and safety in mining, and to make public the results of the investigations. The Federal Government can be of most help in developing the mineral resources of the country when its forces are brought in direct contact with these resources. Mining is as old as civilization, but only within a generation has this country busied itself with any other problem of mining than the amount of mineral products that could be put upon the market. Little concern was felt if much of the metal in an ore was wasted, if the miner lived in unsanitary surround- ings and died of preventable disease, or if accidents occurred fre- quently and from causes that could easily be controlled. Now we realize that the waste of any resource is inexcusable. The mineral wealth of the country can be mined but once. The task before the Nation is to recover as much metal as possible from the ore in the ground, and to do this in the most economical way without waste of human life. This task is of such magnitude as to warrant aid from the Government through experiment stations. In its efforts to make the work of these stations of most benefit to the mineral industry the Bureau of Mines seeks the cooperation of State authorities, of mine operators, of miners' organizations, and of every person interested. These experiment stations also serve an educational purpose. Gen- erally speaking, mining is not a preferred occupation. The miner should have reason to take greater interest in his work; he should feel that the experiments the Government is making affect him vitally by enabling him to increase his production and by making his work safer. The mine operator should realize that the Government stands ready to aid him, and he should know that he can bring his own problems to a Government organization that is trained and equipped to solve them. The surest method of accomplishing these results is to carry the work of the Bureau of Mines into the mining regions through the establishment of experiment stations easily accessible both to the mine operator and to the miner. Many miners in this country do not read English, but they can understand motion pictures of mining methods; they can learn how lives can be saved in case of accident; and they can appreciate the larger results gained by modern methods and equipment. In every

Jan 1, 1919

By Allen D. Look, Alan A. Sharp

"INTRODUCTION The bottoming of the United Verde sulfide pipe has shortened the expected life of the United Verde mine to a matter of a few years. First located in 1876, this Arizona mine has had a long period of activity, having reached a peak production in 1929 of over 71,000 trans of copper. Through these many years of successful operation, a safety program has evolved in keeping with the proficiency developed in mining the ore body. It is the purpose of this paper to record the safety practices in effect at this mine so that others may have the benefit of lessons ,learned through experience 'and years of work toward an improved accident record.ACKNOWLEDGEMENTSAcknowledgment 'is 'made to ,the Phelps Dodge Corp. for its cooperation in making available data contained in this paper, and to C. E. Mills, general superintendent; W. W. Little, mine superintendent; John Riordan, employment agent; and G. S. Leisk, safety engineer, for their helpful suggestions and information furnished.GENERAL INFORMATIONThe United Verde copper mine is situated just west of Jerome, Ariz., at an altitude of approximately 5,500 feet. Purchased by the Phelps Dodge Corp. in 1935, the mine employs approximately 500 men - 385 underground and 115 on the surface."

May 1, 1949

By Irving Hartmann

At the 9th International Conference of Directors of Safety in Mines Research a paper6/ was presented describing the initial phases of research by the Safety in Mines Research Establishment at Buxton, England, on the remote control of timber fires with high-expansion foam plugs in a rock tunnel. The work received extensive publicity, and great interest was aroused by the implied possibility that the method might be used successfully to control coal-mine fires, which for various reasons cannot be approached and attacked by standard fire fighting measures and frequently require sealing extensive, valuable coal properties and lead to loss of production and coal reserves and occasionally loss of lives. To investigate the practicability of the foam-plug technique under American min¬ing conditions, with room-and-pillar-type extraction and multiple entries, the Bureau of Mines in 1957 began an investigation at its Experimental Coal Mine, Bruceton, Pa, In preparation for this work it was necessary to rehabilitate and reinforce an elliptical tunnel in the mine where studies had been made, many years ago, leading to development of a ventilation system used in the Holland Tunnels between New York and New Jersey, and in many other vehicular tunnels.

Jan 1, 1958

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

By M. H. Kersten, G. A. Brady, Jerry W. Ramsey

Anthracite samples were oxidized with nitric acid to prepare products representing intermediate stages of oxidation . Similar oxidizing conditions affected different anthracites to varying degrees as characterized by peptization behavior with 0.1 N NaOH . Techniques used in attempts to separate and characterize the products included esterification , absorption spectrophotometry , sublimation , chromatography , electrophoresis , metal salt formation , and solvent extraction . Mellitic acid , either free or in the form of metallic salts , was identified in the acid- soluble products from 10 tests in which the anthracite was treated with nitric acid for periods varying from 24 to 1,000 hours . pentacarboxylic acid was also found in some products . Other benzene carboxylic acids were not present in amounts detectable by the methods used in this study . The acid- insoluble residue from nitric acid treatment varied significantly in solubility behavior toward different classes of solvents . The most effective ones tried included polar oxygenated solvents and pyridine . Infrared spectra of the extracted material indicated that similar compounds were extracted by the different solvents . Aliphatic amines and aniline peptized the residue and o- toluidine reacted with it . Organic material separated from the residue by peptization with dimethylformamide contained 1 percent ash , consisting of more than 50 percent zirconium .

Jan 1, 1964

By Philip E. Sanker

The Bureau of Mines conducted small-scale batch and semicontinuous tests on the reduction of zinc sulfide with iron according to the reaction ZnS + Fe ? FeS + Zn to determine reaction kinetics in the temperature range 1,000° to 1,400° C and to investigate the potential use of a scrap iron reductant. Batch tests indicated that a temperature of at least 1,300° C with a 1:1 mole ratio of Fe to ZnS is needed for good zinc recovery. Semicontinuous tests were conducted, using four zinc concentrate samples, containing various percentages of copper, cadmium, and lead, which were reacted with iron and iron contaminated with iron oxide and tin in an externally heated graphite furnace. Analysis of the zinc metal and FeS matte reaction products showed cadmium to be entirely in the zinc metal, copper to be in the FeS matte, and lead to be about 60 pct in the zinc metal and 40 pct in the matte. Tin reported to the matte, and none was detected above the O.OS-pct level in the zinc. Sulfur dioxide was not detected in the offgas when up to 20 pct of the iron was replaced by Fe203.

Jan 1, 1976

By D. S. Harper, C. O. Carman

A German coal planer was put in operation in the Keystone mine of the Eastern Associated Coal Corp. , Keystone , W. Va . , in August 1960 . At present , the planer is mining in the fourth panel . The blocks of coal mined were 340 by 1,900 feet in panel 1 , 340 by 1,660 feet in panel 2 , 590 by 1,900 feet in panel 3 , and panel 4 , currently being mined , is 590 by 1,900 feet . Almost one- half million tons of coal have been mined from these four panels . An 11 - man crew handles the complete planer operation and produces an average of 500 tons of clean coal per shift . Self - advancing hydraulic props are used to support the roof over the entire face . Roof control and action on all of the panels has been highly satisfactory . During periods of extreme pressure , some additional support is required in the tail entry where evidence of weight from the retreating longwall extends about 200 feet outby the face . The time lost from production by moving equipment between panels has been reduced steadily . The move from panel 3 to panel 4 required 5 days , but it is believed that even that time could be reduced .

Jan 1, 1963

By A. W. Fahrenwald

The logic leading to the development of the experiments in this paper already has been stated in Part I,3 but is briefly as follows: The results of the batch-grind experiments in which time of "grind" and fineness of finished product were the variables, strongly indicated (1) that batch grinding involving a single grind could not be operated under any condition to give maximum mill efficiency, (2) that the, sieve analysis of the feed charge in the mill materially affected the efficiency of the mill, and (3) that the percentage of finished product in the mill is a vital factor in ball-mill efficiency. A laboratory closed-circuit grind technic designed to simulate present closed-circuit grinding suggested itself, in which: a ball mill and a classifier constitute the grinding unit. The features of the closed-circuit grinding system are: (1) Short large diameter mills, (3) rapid flow of pulp through the mill, (3) continuous automatic removal of finished product from the system, and (4) high circulating loads. The high circulating load is a result if the short length of the Mill - that is, of the time the charge remains in the mill - and the small percentage of finished material produced during each circuit of the feed through the mill.

Jan 1, 1930

By F. A. Rutledge

Mercury deposits were discovered in 1941 in the sedimentary rocks of the Cinnabar Crook area, near the head of the Holitna River drainage in southwestern Alaska, by Russell Schaefer and Harvey Wincholl of Sloitmut, Alaska. High-grade float was found in both Canary Gulch and Cinnabar Gulch, and indications of other deposits wore found in Aldor and Broken Shovel Gulches. Schaefer and Winchell's exploration in 1942 and 1943 revealed placer deposits of cinnabar along Canary Gulch. During prospecting on Canary Gulch, 3,600 pounds of ore was recovered from the detrital material on the Lucky Day lode at the head of the gulch. When retorted, this ore was reported by the owners to have produced 26 flacks of quicksilver. During the summer of 1943, Wallace M. Cady and Charles A. Hickcox, of the U. S. Geological Survey, spent 4 weeks mapping and investigating the area. Bruce I. Thomas and Harold C. Pierce, mining engineers of the Bureau of Mines, examined and sampled several deposits in September 1943. Following their preliminary examination, in view of the exceptionally high-grade cinnabar present, additional investigation by the Bureau of Mines was recommended. A program of trenching, test pitting, and sampling to delimit the deposits was completed during the summer of 1947 under the direction of the author.

Jan 1, 1950