Search Documents

By M. E. Tyrrell

Magnesia spinel (MgO.Al203) recovered from dusting slags in the system MgO.Al203-2Ca0.SiO2 is in the form of single crystals most of which will pass 35-mash. This investigation was undertaken by the Bureau of Mines to evaluate the concentrates as a refractory raw material. Three specific types of refractory bricks were studied: (1) dense, (2) lightweight bubble, and (3) insulating. Test specimens ware fabricated 1 by dry pressing, fired to 1,675° C., and tested by procedures common to the industry. The concentrates produced a refractor, having satisfactory density and mechanical strength; however, spinal is sensitive to thermal shock and the possibility of producing a spall-resistant brick using aggregate of such small grain-size must be considered remote. Lightweight refractorias fabricated of spinel bubbles were the most promising of the types tested. They were 30 percent lighter in sight than the dense refractory, their mechanical strength was good, and definite superiority in thermal shock resistance was indicated.

Jan 1, 1962

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d'Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius3 has damped the vibrations so successfully that a short note concerning it is thought to be desirable, The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp., driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several mudifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects.

Jan 1, 1931

By H. D. Baylor

This paper, describing the operations of the Louisville Cement Co. in quarrying limestone for the manufacture of quicklime, is one of a series being prepared for and published by the United States Bureau of Mines on stone quarries throughout the United States. Those papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author acknowledges the assistance of J. H. Lemmon, plant superintendent, Charles Taylor, plant engineer, and F. H. Compton, chief engineer, of the Louisville Cement Co. in the compilation and preparation of this paper.

Jan 1, 1932

By H. S. Hardman, G. T. Adams, Will H. Goghill

"Usually a newly developed machine leaves the factory ""on a wing and a prayer."" The manufacturer hopes that the operator will hasten to report defects. In turn, when the suggestions arrive the manufacturer makes the required changes and maintains close collaboration with the operator. Thus the history of our machines of today is written.Laboratory concentration tables are exceptions to growth by experiment and collaboration. Their operation never enters directly into the cost sheet; they are seldom used for longer periods than 10 minutes; and the experimenter, while hurrying to another job, accepts the table, good or bad, for a quick test on his ore. Thus we go back about 50 years when we use the preset in factory-built laboratory table.The Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, recognized the existence of a tabling problem net usually considered. That is, instead of using the table to test the ore, the ore was used to test the table. In this critical examination of laboratory table six defects were encountered (and remedied). They are:"

Oct 1, 1945

Provide an unobstructive means of measuring small changes in distance from roof to floor or from rib to rib of a mine opening and the rate of closure in order to help operators of under-ground mines detect hazardous ground conditions. Approach A small ultrasonic measurement system was developed to detect g round movement and define closure rates. How the System Works The system contains two parts: a transducer and a readout device. The small ultrasonic transducer, similar to an audio speaker diaphram, is plucked with an ultrasonic frequency every six seconds. This frequency wave is sent through the air and reflected back to the transducer off any surface at which the transducer is pointed. The amount of time needed by the ultrasonic wave to make this round trip is accurately measured using a precise oscillator / timer and is converted into a measure of distance. The accurate 6-second time interval is used to convert any subsequent changes in the reading to a rate of change in feet per minute. Two readings are then displayed alternately on the readout instrument.

Jan 1, 1984

ESTABLISHMENT of an effective inspection system has been held essen¬tial to any international agreement that may be designed primarily to curb the testing of nuclear weapons. A number of reports and papers already have described basic inspection concepts and appraised various pro¬cedures, techniques, and methods as to their probable effectiveness in detecting and identifying violations under such agreement. This report results from a study of only one part of the contemplated inspection system, specifically the final phases embracing onsite investigations and mine examination techniques. The results and reports of earlier work were reviewed in detail, and subjects that were found to have been exhaus¬tively evaluated are recognized by reference and not redescribed here. In other instances, previously described techniques, methods, and clues were revaluated to define more clearly their practical value to the final objective of an onsite inspection. Previous documentation does not refer to a number of subjects, techniques, tools, clues, and methods considered by the study; this report treats these in detail, even though when applied singly or collectively their practical value may be questionable.

Jan 1, 1962

By A. C. Fieldner

The Bureau of Mines has recently conducted a study of results obtained in analyzing similar samples of coal and coke by 25 laboratories throughout then country, in comparison with results obtained in the Bureau's coal laboratory at Pittsburgh. The purpose of this work was primarily to obtain a comparison of the methods of coal analysis used by the laboratories of the American Gas Association. Therefore, four standard samples of coal end one of coke ware prepared in the Bureau of Mines coal laboratory at Pittsburgh, and portions sent to each laboratory. At the same time, a like number of standard samples were submitted to 12 commercial laboratories rot affiliated with the Association, for the purpose of comparing their analyses with the results is obtained by the U. S. Bureau of Mines and the American Gas Association. Tire comparison is based on the average of 24 analyses by the Bureau of Mines on each kind of coal, and the accompanying curves show the deviation from this average analysis, together with deviations from the check limits of the American Society for Testing Materials.

Jan 1, 1923

Prevent collisions between large mine-haulage trucks and smaller vehicles parked in areas not visible to the haulage-truck operator, Approach Two electronic systems were developed to detect the presence of vehicles in the blind areas of a parked haulage truck. The systems can warn haulage truck operators of presence of vehicles that are blocked from view. The systems do not apply for trucks in travel. How It Works The systems use electronic transmitting techniques-one system is based on low-frequency radio waves and the other on very-high-frequency radio waves. Each system requires that a signal transmitter be mounted on the smaller vehicle to be detected. Continuous signals from this transmitter are sensed by receiving antennas mounted on the right front and rear of the large haulage truck. Upon receiving a signal, the receiver energizes warning lights and a buzzer in the cab of the haulage truck, alerting the operator to a possible collision hazard. Detection distance is adjustable, depending upon the size of the haulage truck, but a minimum of 30 feet was the design goal.

Jan 1, 1990

By Clarence O. Babcock

ROCK BEHAVIOR has proved of national interest in a variety of fields. The behavior of rock consequent to a nuclear blast was used to detect such blasts, as criteria for the design of underground military defense installations that would resist nuclear blasts, and for judging the feasibility for peaceful uses of nuclear explosives. An obvious peaceful application of nuclear explosives would be for large-scale rock excavation, and plans were presented during the year to improve the present Panama Canal or create a new canal by this method. These plans were based largely on earlier crater tests that demonstrated rock behavior when subjected to a buried nuclear blast. A knowledge of rock behavior under impact was used to evaluate the materials of the moon by means of the geometric configurations visible in the close-up pictures of the moon surface taken by the U.S. rocket Ranger 7. The composition of the moon must be considered in devising methods for taking samples of the surface layers or in designing underground shelters as bases for future explorations of the moon.

Jan 1, 1965

By Charles Sabine

The 27,960-acre Newberry Mountains Wilderness Study Area (WSA) is located in the Mojave Desert, 17 miles east-southeast of Barstow. In 1983, the U.S. Bureau of Mines, in conjunction with the U.S. Geological Survey, investigated mineral resources of the area as part of the wilderness review process. The Newberry Mountains are underlain by Paleozoic metamorphic rocks, Mesozoic plutonic rocks, and Tertiary volcanic rocks. Eleven mines and prospects were examined. Of the seven sites within the WSA, only the Northrup Prospect is mineralized. Only a few tons of manganese-bearing rock, containing 49% manganese oxide (MnO), are exposed, but exploration may disclose larger deposits. The Azucar Mine, a past producer of gold, is the only site examined outside the area that appears mineralized. Sample data from quartz veins exposed at the surface do not indicate that resources are present; however, the occurrence could not be fully evaluated because underground workings were not accessible. Sand, gravel, and stone are plentiful in the WSA, but alternate sources outside the WSA are available.

Jan 1, 1985

Late in 1974 at a meeting with the Cedar Coal Company in Chelyan, West Virginia, a very definite requirement for an automatic heat sensing fire suppression system for the type coal augers used in their mine was revealed. Several fires had been experienced, and while equipment loss was a consideration, operator safety was also a concern. As of that date no one had developed an automatic system specifically for fire suppression on coal augers. II. EQUIPMENT DEVELOPMENT As a result of the above meeting, an unsolicited proposal was made to the Bureau on March 1, 1975, and a contract was issued to provide the following services: A. Determine and define fire hazard problem on Compton Coal Auger. B. Modify or otherwise mike a Lease "AFEX" system suitable for protecting the fire hazard area developed in paragraph "A". C. Make installation of "AFEX" system. D. Monitor installation for reliability for a period of 90 days after installation. C. ConJurt a simulated fire test to determine effectiveness on system.

Jan 1, 1975

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

All output is saved in the file MFIRE OUT m the di¬rectory and on the disk containing the program The file can be inspected with a text processor and sent to a print¬er, if needed CONTENTS OF OUTPUT FILE The comment lines, reference temperature, air densi¬ty, a table of the units of measure for the results, and the average values are shown at the beginning of MFIRE OUT All input data will be shown in the output file if LOUT on Control line number 1 is _<-1 For each contamination source, a new branch will automatically be setup The new airway and junction ID numbers will not interfere with the original numbering scheme of the data file Next are the results of the selected simulation(s) in the following order network balancing, network balancing considering temperatures, transient-state modeling, and altered equilibrium due to fire and distribution of the contaminants. Depending upon the contents of the data file, and the simulation selected, attention, warning, and error message will be shown at locations where calculations resulted in unusual conditions

Jan 1, 1990

By T. E. Marshall, D. R. Dolinar, T. M. Barczak, T. P. Mucho

Over a portion of the older limestone mine workings at the NIOSH Lake Lynn Laboratory, a mining health and safety research facility, a large sinkhole formed caused in part by the intersection of several tightly spaced joint sets and unusual weather conditions. The anticipated propagation of the associated roof failures threatened to encroach upon a portion of the facility’s secondary escapeway. To protect the escapeway, two cribs walls and over 80 cable bolts were installed. In addition, extensometers were installed to monitor roof movement in the escapeway. However, a large roof fall associated with the propagating roof failures in the sinkhole area partially destroyed one crib wall where the adjacent escapeway was not reinforced by cable bolts. Recent roof movement information indicates that this area is still active. Based on these measurements, steps have been taken to stabilize this portion of the escapeway. This paper discusses roof monitoring, the roof movement, the large roof fall, propagation of the roof failures, and the recent support measures undertaken to stabilize the escapeway.

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global plate-tectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20° in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed.

Are you afraid of the dark? Of course not, at least not since you were about six years old, anyway. But early man was - afraid of the dark, and he had good reason to be. Since he had no illumination other than fire and moonlight, he was at a disadvantage when it came to mixing it up with some of his fellow creatures. Sabre-toothed tigers, for example, could probably see quite well In the dark, and they were very real enemies. Sabre-toothed tigers haven&apos;t been seen in mining country for some time now; but it&apos;s st111 dark In a mine and, make no mistake about it, there are still enemies in the dark. The enemies are all the things that can injure you if they are not seen. Modern mines can be safe places to work for the trained miner who follows good work practices. But there are mining machines that make sabre- toothed tigers look like pussycats, and if you can&apos;t see well enough they can be ten times more dangerous.

Jan 1, 1976

By R. D. Leitch

In the course of another investigation4 during 1926 and 1927, samples of water collected from a few abandoned coal mines indicated that their drainage was usually lower in acidity than water from active mines in the same locality. In order to determine whether this condition might have a bearing on the advisability of sealing abandoned mines, a number of such mines were visited, samples of drainage were collected, and as much information as possible was obtained from officials of the mining companies and older residents of the district. The results of this work are the basis of the present report. ACKNOWLEDGMENTS The authors are indebted to E. W. Robertson, F. F. Spowart, J. H. Nagle, and W. D. Adams of the Northwest Mining & Exchange Co.; E. M. Fasset, Fred Lane, Wm. Humphreys, and Dr. T. A. Hutchison of Brockway, Pa.; C. W. Faulk of the Shawmut Mining Co.; James Hau of Kersey, Pa., and do others for information received; and to Dr, R. R. Sayers of the Bureau of Mines, under whose direction the work was conducted.

Jan 1, 1928

By Thomas V. Falkie, R. Venkataramani

The purpose of this work was to Investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors - geometrical , geological, mechanical, or procedural - which affect the delivery rate, and to develop quantitative rate-descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily Influences the loading function The geometrical factors -the dimensions of the work area In relation to the dimensions of the mining machine -were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent Independent variables. It is expected that this work will be useful In operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Sep 1, 1972

By E. C. Lane

"INTRODUCTION This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36 3/. The second resort gave the same data for motor gasolines sold during the summer of 1936 4/. The third report of the series gave the same data for motor gasolines sold during the winter of 1936-37 5/.This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others."

Dec 1, 1937

Provide low-cost fire protection for big bulldozers. Approach A fire protection system, previously used on mobile logging equipment and adapted to surface coal augers, has now been adapted for use on large mining bulldozers. How It Works Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system. The system can also be manually activated from either the opera-tor&apos;s cab or ground level. Location of the principal components of the system are shown in the drawing The heat sensors of the sys-tem consist of bimetallic strip switches which operate at about 10000F temperature. Switch operation results in release of compressed gas from a small storage cylinder. The gas expands to blow the dry chemicals out of the nozzles, in a spray that lasts about 15 seconds. The compressed gas used is usually nitrogen, although carbon dioxide is also used.

Jan 1, 1978

By A. R. Rule

Laboratory tests were conducted to study removal of magnesium impurities from western phosphate rock concentrates by selective leaching. The systems evaluated included leaching with dilute sulfuric acid, with ammonium sulfate, and in an aqueous medium with sulfur dioxide gas. Set standards for the magnesium impurity level of phosphate rock concentrates are not available, but industrial practice has indicated that magnesium in excess of 0.3 percent MgO causes problems in phosphoric acid manufacture. Removal of magnesium was accomplished with all three systems. With dilute H2S04 the magnesium level was reduced to less than 0.1 percent MgO with an accompanying P205 loss of 6 percent. Magnesium oxide levels from 0.3 to 0.2 percent were obtainable with ammonium sulfate. However, the system requires concentrate roasting at temperatures of 900° C or higher, heated pulps (100° C), and large quantities of ammonium sulfate. Selective leaching was obtained using S02 gas in an aqueous concentrate slurry. Magnesium oxide content was reduced to less than 0.1 percent without loss of phosphate.

Jan 1, 1970