Search Documents

By C. W. Owings

"Ventilation is one of the most important features of coal mining, and if a mine is exceptionally gassy it is often difficult to ventilate it in such a way as to make it safe. The general system of splitting the main air current so that two, three, or more sets of room entries are ventilated by the same current of air does not provide a safe method if non-permissible electrical equipment, such as cable-reel, crab-reel, or trolley locomotives are used on gathering haulage, or if open-type hoist or pump motors are used. The problem has been greatly simplified at the Crucible mine of the Crucible Fuel Co. at Crucible, Pennsylvania.The system is not only applicable to the room-and-pillar method of mining, but it may be adopted for any panel system of mining. There also appears to be a definite application in mechanized mining, where the rapid extraction often results in inadequate attention to ventilation and where the gassiness of the section generally increases because, as compared to hand loading, the methane has less time to drain off. The system to be described should commend itself to coal-mining men.ACKNOWLEDGMENTSThis investigation was made possible through the courtesy of H. J. Nelms, general superintendent. E. M. Marshall, safety inspector, E. G. Sauers, assistant superintendent, and Thomas Mark, mine foreman, assisted in the collection of information."

Sep 1, 1931

By R. D. Leitch

Spontaneous firing of coal during storage end even during shipment has long been a serious problem, especially in some regions and with some coals, and methods for preventing such firing have been investigated at intervals for more than 70 years. Spontaneous or other firing of coal waste, either outside or inside mines, has also been a problem probably for as long as mining has been practiced extensively. Much trouble has been caused by such fires, and much money has been spent in attempts to extinguish them. It is known generally that surface waste banks in bituminous-coal fields are very likely to take fire sooner or later, but it is not known so generally that anthracite refuse-bark fires also are common and that at least some of them are more serious in their effect and results than being regarded merely as a nuisance. There surface refuse fires probably would have attracted much more than local attention long ago had it not been that they usually cause no more serious trouble than air pollution. A few supposedly effective methods of preventing or extinguishing spontaneous fires have been reported rather recently. Unless one or more of these prove to be widely applicable, methods of solving these problems are no more certain today than they have been for many years.

Jan 1, 1940

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By O. P. Hood

The spontaneous combustion of coal lies at the bottom of the subject of storage. It is useless to store coal that is to be lost by fire from spontaneous combustion. Every engineer is familiar with the phenomena of the self-heating of coal, yet, for all that, spontaneous combustion is relatively rare. If we counted the times a portion of cod was stored where it would be undisturbed for a few weeks, the number of such storage operations in any one year would mount into the millions. Of these, a relatively small number show the phenomena of spontaneous combustion and time risk per ton is very small. It is extremely rare that in the smaller operations involving; only a few tons there is any heating. There is no spontaneous combustion of anthracite, and very rarely does the domestic consumer of bituminous coal find troublesome heating. The main interest in the subject lies in the large piles needed as reserves for public-service utilities, and the industries. Everyone desires to have directions for storage that are perfectly simple and yet will insure against loss. Unfortunately, the problem is too complicated for a simple solution. Many of the factors involved are difficult to determine, as we have no practical means of quantitative measurement. The factors involve chemistry, physics, and engineering, and the man who is

Jan 1, 1939

By John J. Sammarco

Computer-related accidents have caused injuries and fatalities in mining as well as other industries. Normal accident theory (NAT) explains that some accidents are inevitable because of system complexity. NAT is a classic argument in organizational sociology although it has been criticized as having imprecise definitions and lacking criteria for quantifying complexity. These limitations are addressed by a unique approach that recasts this organizational theory into an engineering-based methodology to quantify NAT complexities of computer-based systems. In this approach complexity is categorized as external or internal. External complexity is defined by the external behavior of a system, and is quantified by these dependent variables: system predictability, observability, and usability. Dependent variable data contain the perceptions of 32 subjects running simulations of a system. The system?s internal complexity is characterized by modeling system-level requirements with the software cost reduction (SCR) formal method. Model attributes are quantified using 15 graph-theoretical metrics?the independent variables. Five of 15 metrics are correlated with the dependent variables as evidenced by structure correlations exceeding 0.25, with standard errors <0.10 and a 95% confidence interval. The results also show that the system predictability, observability, and usability decreased as NAT complexities increased. This research takes a step forward in operationalizing NAT for computerized systems. The research benefits mining and other industries as well.

Jan 1, 2005

By H. M. Cooper, R. F. Abernethy

Determination of the fusibility of coal ash consists in melting a pyramid of the ash to fluid under prescribed conditions . The conditions of the test are specified by the American Society for Testing Materials4/ and must be adhered to strictly if comparable results are to be obtained . The Society formerly specified a particular type of furnace , but with improvements in design of both electric and gas furnaces , it was decided by the Society to specify only essential details of the test . The Chairman of Committee D - 5 , Coal and Coke , of the American Society for Testing Materials suggested that the Coal Analysis Section of the Bureau of Mines conduct a cooperative investigation on the effect of furnace type and atmosphere upon fusibility of coal ash . The Coal Analysis Section enlisted the aid of a number of laboratories using the more common furnaces to cooperate in the investigation . Four types of gas furnaces burning natural and manufactured gases and two types of electric furnaces with different methods of maintaining a reducing atmosphere were employed . The results from the survey are tabulated herein , and some comparisons are made . There were not enough data from any particular furnace and atmosphere to make a reliable statistical analysis . However , definite tendencies are evident , and attention is called to them by direct comparison. in tables .

Oct 1, 1943

By R. M. Santmayers

[This paper presents one of a series of digests of foreign mining legislation that is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining legislation of Bulgaria was prepared from a copy (in French) of the Mining Laws of Bulgaria, promulgated by Royal Decree No. 33 of I. arch. 31, 1910, and published in the "Journal Official," No. 83, April 14, 1910, and checked against a digest prepared by Maynard B. Barnes, First Secretary, American Legation, Sofia, Bulgaria, dated June 10, 1932, which was transmitted through the courtesy of the Department of State. CLASSIFICATION OF MINERAL SUBSTANCES Mineral deposits are classed either as mines or quarries. (Art. l.) Tunes are deposits, the products from which must be processed. Under this class specific mention is made of the metals (gold, silver, copper, lead, zinc, iron, chrome, titanium manganese, tungsten, tin, mercury, platinum, cobalt, nickel, cadmium, aluminum, molybdenum, bismith, uranium, antimony, arsenic), sulphur and other "analogous" mineral substances, phosphate rock, iron pyrites, sulphates, saltpeter, alum, boracic acid and its compounds, talc, asbestos, amber, graphite, merschaum and precious stories of all kinds, reek salt and other salt, peat, coal, petroleum, ozocerite, asphalt and all other bituminous substances. (Art. 2.)]

Jan 1, 1933

By Spangler Ricker, F. T. Johnson

"SUMMARYThe Ione-Carbondale clays area is 2 miles northwesterly of Ione, Amador County, Calif. It was explored during the war by the Bureau of Mines to obtain data on the alumina content and to recover representative samples for beneficiation tests for alumina recovery.Seventy holes, aggregating 8,837 feet, were drilled, and about 10.3 acres of land was cleared of underbrush. Maps and cross sections were compiled showing location of holes, analyses, and other pertinent data.The clay beds vary in thickness from 13 to 196 feet, and are covered by a loose overburden, averaging about 11.9 feet in thickness. The ratio of overburden to clay is 1 : 8.2. Analysis of a composite sample showed the recoverable alumina (A12O3) and Fe2O3 content to be in the order of 23.6 percent and 2.8 percent, respectively.Topography of the clay area is ideal for open-pit mining methods and plant site.INTRODUCTIONInvestigation of alumina-rich clays for the possible production of aluminum was made during the recent war period, when the shortage of bauxite was becoming critical.Results of field examinations by the Bureau of Mines and the Federal Geological Survey indicated that one of the most promising areas for the development of alumina-rich clays is in the Ione-Carbondale district."

Mar 1, 1948

By Wilder H. Brinton

"INTRODUCTION The Queen Mary copper property is in sec. 18, T. 12 N., R. 16 W., in the Clinton mining district of Missoula County, Mont. It was examined by an engineer 3/ of the Bureau of Mines, November 21, 1943. Upon the basis of his recommendations, a small trenching and diamond-drilling program was begun November 11, 1944. One diamond-drill hole was completed December 16, -944, but because of frozen ground trenching was postponed until June 1945 and then completed. This report describes the results of exploration.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyses samples and performs beneficiation tests. Both of these branthes are under the supervision of Dr. R. S. Dean, assistant director.The chemical analyses included in this report were made at Reno, Nev., under the direction of A.C. Rice, acting engineer in charge. Rare and Precious Metals Experiment Station, Bureau of Mines."

Nov 1, 1946

By Raymond B. Ladoo

"Domestic Situation:The greatly increased use of lithopone as a base for paints, particularly for interior use, has timulated the demand for barytes to such a degree that the supply cannot keep pace with the demand. Lithopone is an artificially prepared compound composed of about 70 per cent barium sulphate and 30 per cent zinc sulphide, precipitated together. Its most important use is in paint, but it is also used in oilcloth, linoleum, rubber goods, shade cloth, etc.Prior to the war large quantities of barytes were imported from Germany, but during the war imports were negligible, domestic production increased very greatly and is still increasing. Ground barytes as used in paints/ formerly regarded as an adulterant, but now it is generally recognized as a valuable paint constituent. Mile domestic sources have expanded rapidly they have not overtaken the demand and there is need for still greater expansion. Stocks are low, little is being sold on the open market, and prices are high. Since barytes is a gangue mineral associated with metallic ores now being mined in the west, it is suggested that more attention be given to its recovery as a by-product.The following tables compiled from reports of the U.S. Geological Survey and the Bureau of Foreign and Domestic Commerce, indicate the growth of domestic consumption."

Jan 1, 1920

By R. D. Leitch, C. A. Taylor

Trinitrotoluene is made by the direct nitration of toluene by a mixture of nitric and sulphuric acids . The exact procedure varies , but the product , where Grade I of TNT is desired , is similar , and consists largely of material that has a melting and setting point of 80.6 °c . The purification consists of draining off the liquid portions , including the acid and liquid nitro compounds . The mass is crushed and washed until the TNT is acid - free . It may still have a low-melting point due to the presence of material of lower nitration. Other isomers also have the same effect . The crystal mass may be washed with a solution of sodium sulphite , thiosulphate , sulphuric acid , or with an organic solvent such as alcohol , benzene , or carbon tetrachloride , Where a very pure product is desired , the TNT is separated by fractional crystallization from solution in organic solvents . The TNT is If it forms In some cases the material is melted during purification . agitated as it cools to prevent solidification in a solid mass . in a solid mass , this is broken up and screened . There has been some question as to the effect of the different methods of purification on the strength and sensitiveness of TNT , although all methods left a product that would give satisfactory tests .

Sep 1, 1923

By John Taber, Robert D. O'Brien

"INTRODUCTION The Bozeman corundum deposit was first examined in May 1944 by an engineer of the Bureau of Mines. In August 1944, the property was re-examined because of a sharply increased war demand for corundum. A small program of trench exploring was undertaken after the second examination. The work was started in October 1944 and was completed in December 1944. This report presents the essential data obtained by the exploratory work.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that, they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploration work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests.The field work on the Bear Trap project was supervised by E. W. Newman, district engineer Montana District office. The microscopic examinations and. the grid grain-count analyses of the samples and the beneficiation tests were made at the Bureau's laboratory at Salt Lake City, Utah, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

May 1, 1947

By Eugene Frey

"INTRODUCTION The Good Fortune mine was sampled by an engineer of the Bureau of Mines in June 1944. Project 984 was set up under the strategic minerals program to make old workings accessible for this sampling program. Actual operations commenced June 1, 1944, and were completed June 30, 1944.The deposit was visited and discussed briefly by Sidney H. Ball 3/ of the Federal Geological Survey in the summer of 1906 and by H. M. Chance 4/ several times from 1887 to 1900.LOCATION AND ACCESSIBILITYThe Good Fortune mine is situated in the Hartville mining district in Platte County, Wyo., approximately 9 miles northwest of the town of Guernsey. The property is about 100 miles north of Cheyenne, Wyo. (fig. 1).ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metal¬lurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests."

Aug 1, 1947

By Franxis Church Lincoln

"INTRODUCTION During September 1944, the Bureau of Mines undertook a program of investigation and limited exploratory drilling at the Last Chance mine, near the village of Arthur in Grant County, Wisconsin, as part of a general investigation of the zinc-producing area of southwestern Wisconsin when every effort was being made to increase the production of metals important to the Nation's war program.The Bureau's attention was directed, to the Last Chance mine when the operators discovered high percentages of zinc in an exploratory churn drill hole a short distance southeast of the mine. The ore was found in the Trenton Limestone, which underlies the ore horizon then being mined. To determine whether this discovery was important, and to demonstrate the possible extension of the ore the Bureau of Mines drilled five additional holes in the vicinity of the discovery.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report."

Mar 1, 1947

By J. J. Bourquin

"The Keely mine at Dagger, Indiana, is one of the few mines that is being operated successfully on a cooperative basis. This shaft mine is developing 133 acres of coal in the Indiana No. 6 bed, which here averages 5-1/2 feet thick and. lies about 110 feet below the surface. Thirty seven (37) miners and twenty (20) company men or day man are employed, and the daily output is around 300 tons. Practically the entire production is sold by contract for railroad use. No mining machines are used and all coal is produced by pick work.The mine was originally owned and operated by the Stockton Coal. Co. of Dugger, but about eight years ago it was leased to Mr. Roy Price. He sub-leased the property to ten miners, who formed an association known as the Dugger Mutual Coal and Mining Co., to work the mine cooperatively.At first many difficulties were encountered; the cooperative idea is an old one, but the practice was new to those interested. Some of the men were energetic, ambitious workers; others were inclined to let their associates produce the coal but wanted to share in the profits. In time, after a hard struggle and many changes in the personnel of the company, business-like methods were adopted and the mine was put on a paying basis."

Feb 1, 1983

By Robert C. Ellman

Stockpiles containing 2.3 million tons of lignite constructed in the period 1948-56 in conjunction with the construction of Garrison Dam on the Missouri River demonstrate successful stable long-term storage of lignite. Uniform and thorough compaction of each of the I-foot-thick layers by which the piles were constructed produced a bulk density of 70 Ib/cu ft. Air penetration into the stockpiles was restricted to a degree that prevents spontaneous heating or deterioration of the stored lignite, A continuing record of observations beginning with stockpiling operations in 1948 has been accumulated, This includes periodic fuel analysis, analysis of pile gases, and measurement of pile temperatures on the first large stock-pile, pile 5. This report describes the stockpiling method, the changes in heating value, pile gas composition, and pile temperature and summarizes observations from 1953 to 1964, Data accumulated attest to the stability of the stored lignite. The variation of the average heating value of periodic pile-depth samples is only 160 Btu/lb (11,990 to 11,830) on the moisture" and ash-free (maf) basis during almost 10 years of storage. Temperature levels of the pile interior are progressively decreasing. At pile surface, cyclic variations occur with the season. The only problem encountered with the large stockpiles is wind and water erosion of the pile surface. The partially successful control measures used are described.

Jan 1, 1967

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

The Bureau of Mines has developed a system using a high-speed electropneumatic mechanism for the rapid (grab) sampling of dusts and gases during an explosion. The sampling system consists of an aluminum housing that incorporates two 30-cm3 preevacuated glass vials with rubber septums. Upon actuation, the sampling probe needle is driven through the septum with a pressurized air pulse, filling the tube with gas and dust from the mine explosion. After a predetermined time, the sampling probe needle is retracted by a second high-pressure air pulse to its normal (quiescent) state, allowing the sampling tube to reseal. The onset and the duration of sampling are independently variable and controlled by a time-delay relay package. This technique enables the monitoring of pyrolysis-charring in coal particles and the generation and combustion of the pyrolysis vapors in both large- and small- scale explosions. The following results were obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Laboratory: (1) Gas sampling of the leading edge of the flame front shows the large concentration changes, characteristic of the flame front; (2) gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen; and (3) the particles collected in the flame zone show signs of extensive pyrolysis and charring.

Jan 1, 1988

By R. V. Ramani, V. T. Burgos, J. A. McClay

The data for Test I describes an underground bituminous coal mine operation in a 48 inch seam, with an estimated production rate of 1,056,000 tons per year. The system includes four continuous mining sections, conveyor belt haulage, and a rail network for supply and personnel transportation. This section illustrates the input data sequence and the various report formats which may be selected for the printing of results. As explained earlier, at the present time, the elements of the Cost Data Library must be read in with the regular data input. Thus, in the input data listing, immediately following the required user input, are cards which contain the inputs of the cost library. Examination of the cost reports indicate the absence of cost values for some categories for which the system would normally be expected to incur costs. This situation has arisen due to the format of the cost data provided in the U. S. Bureau of Mines reports. An example of this is the charge of $20/ton for brattice cloth while no charge is indicated for stoppings. The test report data provided a single figure for ventilation cost without a supplemental breakdown. Thus the cost indicated for brattice cloth is actually the total ventilation cost. These explanations hold true for the data input and output for Test II, Appendix III.

Jan 1, 1975

By Travis Q. Lyday

Australia was one of the world&apos;s principal producers of minerals and metals, and its minerals industry was a leading catalyst in promoting growth of the country. Australia was the world&apos;s largest producer of alumina, bauxite, diamond, ilmenite, monazite, opal, rutile, sapphire, and zircon. It was the premier exporter of alumina, coal, ilmenite, refined lead, monazite, rutile, and zircon, and was the second leading exporter of iron ore, after Brazil. Ranking behind China, the United States, the U.S.S.R., the German Democratic Republic, Poland, and the Federal Re-public of Germany, Australia was the seventh largest producer of coal (all grades) in the world. Australia was the fourth largest gold producer in 1988, after the Republic of South Africa, the Soviet Union, and the United States. It was the second largest producer of zinc, the third largest producer of nickel, the fourth largest producer of uranium, and the seventh largest producer of copper. 2 The country&apos;s mineral wealth was so extraordinary that it was virtually self-sufficient in most mineral commodities. Endowed with abundant resources of coal, natural gas, liquefied petroleum gas, and uranium, Australia was one of the few market economy countries that was a net exporter of mineral fuels. About 90% of Australia&apos;s consumption of crude oil was supplied by domestic production; this was expected to decline significantly about 1990, unless significant new oilfields were discovered.

Jan 1, 1990

By R. Karl Zipf

MULSIM/NL (multiple scams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines and thin metalliferous veins. It can analyze one to four parallel seams that can have any orientation with respect to the Earth&apos;s surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) nonlinear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. Detailed checks show that numerical stress and displacement calculations compare well to known analytic solutions for simple problems. The total energy release calculated by MULSIM/NL is comprised of three basic terms: (1) strain energy release from the mined-out material, (2) linear kinetic energy release due to change in gravitational potential over the mined-out area, and (3) nonlinear kinetic energy release due to nonlinear materials in the total backfill and gob area. The strain energy release term is modified to account for nonlinear stress-strain behavior in the unmined materials. Comparisons of these numerical energy release rate calculations with known analytic solutions show excellent agreement.

Jan 1, 1992