Search Documents

By L. A. Johnson

This Bureau of Mines report presents the analysis of three cores from the Asphalt Wash area of the P.R. Spring tar sand deposit of northeastern Utah. Two tar sand zones are indicated in the Asphalt Wash Area. Total net thickness of the tar sand ranges from 23 to 39 ft, with occurrences between 56 and 263 ft in depth. The sand has average porosity of 24.7 pct of bulk volume, average permeability before and after extraction of 87.5 and 596 md, respectively, and average oil saturation of 58.1 pct of pore volume. Oil gravity averages 10.9° API.

Jan 1, 1975

By D. Bienstock

A high-B.t.u, gas can be synthesized by the catalytic methanation of a mixture of 2.5 to 3 parts of hydrogen to 1 part of carbon monoxide, obtained in the gasification of coal, using a steel catalyst followed by Raney nickel in a hot-gas-recycle system. Conversion of 99 percent of the H2+CO yields a fuel gas with a heating value of 983 to 1130 B.t.u. per cubic foot containing 78 to 96 percent methane, no carbon monoxide, and very small amounts of unsaturated hydrocarbons. With the steel catalyst alone, conversions were 85 to 90 percent, giving a fuel gas of 810 to 868 B.t.u, per cubic foot, or 847 to 975 B.t.u. on a C02-free basis. INTRODUCTION In 1948 the U.S, marketed production of natural gas was 5.15 trillion cubic feet; by 1958 it had reached 11.0 trillion cubic feet, a rate of growth of 8 percent annually. 4 5 Although demand is expected to increase less rapidly, by 1966 it may reach 16 trillion cubic feet, based on an estimated 4.7 percent annual increase.6

Jan 1, 1961

By D. R. Mathews

The solubility of carbon in electrorefined vanadium was determined to be approximately 0.27 wt pct at the eutectic temperature 1,650° C and 0.03 wt pct at 700° C. The tensile strength and hardness of vanadium increased with car-bon content to the solubility limit, but this effect was small, probably because of the narrow solubility range. Between the solubility limit and 0.3 weight-percent carbon, the second phase had essentially no strengthening effect in vanadium. The second phase, observed metallographically at the grain boundaries and within the grains, was shown by autoradiography to contain high-carbon concentrations. This second phase was identified as VgC by X-ray analysis. The VgC in the grain boundaries contributed largely to the poor cold-and-hot workability of vanadium-carbon alloys. Increased concentrations of V2C occurred at the grain boundaries of the high-carbon alloy ingots as a result of homogenization at 1,600° C for 1 hour. Alloy ingots containing more than 0.36 wt pet carbon (a calculated 2.9 wt pct VaC) following homogenization, cracked severely and failed by intergranular fracture upon swaging at 900° C.

Jan 1, 1965

By B. W. Madsen

Research by the Bureau of Mines has shown that treatment of open pit waste by crushing and sizing followed by flotation of the fines and leaching the coarse fraction results in greater metal recoveries than obtained by leaching only. Tests with a chalcocite-bearing quartz monzonite mine waste sample that had been crushed to minus 6 inches and screened on 1/2 inch yielded copper and silver recoveries of 71 and 22 percent, respectively, by the combined flotation-leaching process, compared with 48 percent of the copper and no silver recovered leaching the run-of-mine material. Copper was more readily leached from the coarse material with the minus 1/2-inch fines removed than from material with the fines included. The improved leaching was attributed to improved permeability and the associated improved circulation of air to the interior of the ore column. Cost estimates showed that the proposed intensive treatment of mine waste will require a greater capital investment and higher annual operating costs than conventional milling and dump leaching process. However, the income from the additional metal production offsets the increase in capital investment and operating costs, resulting in additional profit.

Jan 1, 1975

By K. E. Stanfield

One of the initial projects under the oil-shale research and development phase of the Synthetic Liquid Fuels Act, Public- Law 290, 78th Congress, approved April 5, 1944, was a survey of oil shales of the United States for the selection of a site for an oil-shale demonstration plant. The oil shales were assayed by the conventional Bureau of Mines retort method proposed by Karrick and described by Guthrie in a more recent publication. From previous experience and that had in making these assays, it became evident that the assay method should be modified or replaced by a more satisfactory one. There are several outstanding objections to the Bureau of Mines oil-shale assay method: (1) the oil yields are frequently smaller than those obtained by other types of assay equipment and by commercial retorts; (2) the assayed oil yield represents only a portion of the organic matter in the shale, which under more favorable conditions, may, Jae converted, more completely into oil; (3) the retorting procedure is controlled mainly by trial-and-error methods; and (4) the assay requires approximately 6 hours for completion.

Jan 1, 1949

By Deborah A. Kramer

An economic and technical evaluation of a proposed process to recover alumina by leaching calcined kaolinitic clay with sulfurous acid is presented in this Bureau of Mines report. After the insoluble portion of the clay has been removed by leaching, monobasic aluminum sulfite is precipitated from the pregnant leach solution by partial hydrothermal decomposition. Further heating completes the decomposition to an impure alumina hydrate. This intermediate is purified in a modified Bayer process, which includes dissolving the alumina hydrate in a caustic solution at high temperature and pressure, then decreasing the temperature and pressure to precipitate alumina trihydrate. Calcining the trihydrate produces the alumina product. A cost estimate was prepared for a plant producing 1,000 tons of alumina per day, 350 d/yr. The estimated operating cost is approximately $475 per ton of alumina. This is substantially higher than a comparable estimated operating cost for the Bayer process of $250 per ton of alumina. The proposed process does not appear economically attractive, even as a method to modify a current Bayer processing plant to use a kaolinitic clay feed. High capital costs and high energy requirements make the process prohibitively expensive.

Jan 1, 1983

By J. B. Carman

This paper, describing the concentrator of the Molybdenum Corporation of America in Taos County, northern New Mexico. 7 miles east of Questa, is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. The mine from which the ore comes is 1 1/4 miles from the mill, and produces about 40 tons of ore per day by the cut-and-fill method.3 The ore contains about 5 per cent of MoS2. The mill has a capacity of 50 tons of ore per day and utilizes flotation methods. Water is taken from Red River. Power is generated by a water wheel, or by a Diesel engine in times of water shortage during the winter. The mill is located close to the bottom of a canyon, in order to obtain maximum head or, the water wheel, and the flow of ore is therefore maintained partly by gravity and partly by an elevator and pumps. ORE TREATED The MoS2 content of the concentrator feed ranges from 4.5 to 7.5 biotite, fluorite, small amounts of rhodochrosite and calcite, and the minerals of the granodiorite country rock.

Jan 1, 1932

By M. W. Pullen

It is recognized that the determination of electrical resistivity of the earth within a given area may furnish information concerning the location of certain mineralized strata of economic importance. Present knowledge of the electrical resistivity of the various rock formations is almost nil, and the geophysicist who is detailed to make a survey of an area without any data as to the relative resistivity of the underlying rocks is greatly handicapped. Such surveys are usually made within areas known to contain mineral deposits to aid in locating desirable points for drilling. Usually these areas have been prospected by diamond drilling, and drill cores of the various rocks and ores are usually obtainable. Were it possible to make resistivity tests in a laboratory of the drill cores or from pieces of the rocks and ore within an area before attempting a field survey, this would indicate not only the advisability for such a survey but would aid considerably in the interpretation of the results of such a survey. To be of most value a definite method should be used for all such tests, and as yet such a method has not been established.

Jan 1, 1929

By Anthony W. Sparks

The Bureau of Mines conducted tests designed to compare its breathing metabolic simulator (BMS) with other methods that are currently used to evaluate the performance of respiratory protective equipment. The BMS is a commercially developed device that uses a piston cylinder to simulate breath movement. Using a propane furnace that consumes oxygen and forms CO2, the BMS also simulates the respiratory metabolism of humans. The breathing and metabolic subsystems of the BMS are described in detail in this report. Results are compared from tests that used the BMS to evaluate respiratory equipment and from tests that used human subjects for the same purpose. The BMS was also tested against a pulsatile breathing machine (PBM) previously designed by the Bureau. Both machines were used to test respiratory equipment, and the test results are compared in this report. To illustrate typical applications of the BMS, the report briefly describes how the BMS was used to test two different types of closed-circuit respiratory apparatus, and the test results are presented. This research showed that BMS test results compared more closely to the results of tests that used human subjects than did results obtained using the PBM.

Jan 1, 1980

By S. W. Parr, T. E. Layng

There is presented below the results of experiments made on six samples of Utah coals furnished through the U. S. Bureau of Mines , under an agreement dated June 16th , 1920. The details of all values for all runs are tabulated and presented herewith . Clear The samples, consisting of approximately 150 pounds each, were received at the University of Illinois , on June 15 , 1920 , and are listed as follows : Creek , Wattis , Castle Gate , King , Standard , and Aberdeen . The proximate and ultimate, analyses of the various ccals from that region , representing all the types included in these samples , have already been made by the Bureau of Mines , and are available . * Similar determinations were also made on the particular samples forwarded for purposes of these experiments . The results obtained on the coal as received did . not very in any material feature from the values reported by the Bureau, they are shown in Table 1. It is of importance to note only that the oxygen content is uniformly high , namely approximately 9.5 to 11.5 per cent of the as- received coal , while the oxygen - hydrogen ratio is also high, being on the average approximately 2 ( oxygen) to 1 ( hydrogen) .

Sep 1, 1921

By Robert N. Roby

Deposits of iron ore in Judith Basin County, Mont., generally referred to as the Running Wolf deposits, were examined by an engineer of the Bureau of Mines in August 1942. During the Summer of 1943 the Federal Geological Survey made a reconnaissance survey of, the Running Wolf Iron district and also made a detailed study and a topographic and geological map of the eastern end of the district. Two deposits of iron ore at the eastern end of the district were trenched and drilled by the Bureau of Mines during the fall and winter of 1943-44, This report presents the factual data obtained from the trenching and drilling' operations. The iron deposits of thy Running Wolf district are accessible from Stanford, Mont., by 14 to 16 miles of county highway and 2 to 3 miles of rough mountain road or trails (see fig. 1). No shipments of ore have been made from of these deposits. The ore is a replacement of Madison limestone at the contact with syenite porphyry. The contact can be traced for about 6 miles in a general northwest direction. 'At least five. deposits occur along this contact.

Jan 1, 1949

By S. M. Shelton, F. D. DeVaney, M. M. Fine

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced ; although it is well -known that there are large deposits of low - grade ore in the United States , the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore is depleted through inability to obtain adequate supplies from foreign sources . Consequently, a program of laboratory and pilot - plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines . This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program . The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series , Report of Investigations 3606 , Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent , and C. H. Schack . Other reports will be published as the work progresses .

Feb 1, 1942

By J. B. Zadra, S. M. Shelton, M. M. Fine

"Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well known that there are large deposits of low-grade ore in the United States, the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore is depleted through inability to procure adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigation designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines.This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that woo set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3606, Manganese Investigations. 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. R. Schack. Other reports will be published as the work progresses."

Mar 1, 1942

By Harry R. Nicholls

As part of the pre- and post - shot mine examination at Project GNOME , acceleration data were recorded underground from a series of chemical explosive shots . The cube root of the charge weight was used to scale acceleration and distance because charge weight was not constant . Regression analysis of particle acceleration - distance data gave the following propagation equation : A W1 /3 = 5.10 x 105 ( R / W¹ / 3 ) −2 .43 The quantity A W1 /3 is scaled particle acceleration expressed in g's - lbs¹ / 3 , and R/W1 /3 is scaled distance expressed in ft / lbs¹ /3 Data obtained from the nuclear explosion were scaled and fall within one standard deviation of the calculated propagation law for the smaller shots . Cube root scaling laws were adequate to group acceleration data from explosive charges varying by a factor of more than 1 x 10 in charge weight and over shot - to - gage distances varying from 100 to 46,000 feet . Data obtained from a series of small tests provided sufficient data from which reliable predictions of acceleration could be made for the large nuclear explosion .

Jan 1, 1964

By R. H. Thompson

Six different types of blasting caps, mainly of the type used in coal mines, were evaluated to determine both their 1lF and DC characteristics. Two of the caps were of foreign manufacture. All the American made caps had "no-fire" (0.1% firing probability with 95% confidence, as determined by the Bruceton test) levels above 0.04 watts. One of the caps of foreign manufacture had a "no-fire" level of 0.023 watts. A worst case analysis of blasting cap pick up of RF power in coal mines was performed and safe distance curves were generated.

Jan 8, 1973

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

A complete list of permissible mining equipment, rescue apparatus and gas masks tested. Prior to Jan. 1, 1929, w s published in Bureau of mines Information Circular 60972. The present list includes practically all equipment tested and. approved by the Bureau, up to and including July 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists,, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage battery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which these devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal showing hat it has been "approved" by the Bureau. These tests are designs to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and publishing lists of permissible equipment is to safeguard the lives of workers and to help lessen the hazards of mining.

Jan 1, 1929

By Charles Vaught, Kathleen M. Kowalski

Safety and health professionals from all sectors of industry recognize that training is a critical element of an effective safety and health program. A major concern in the mining industry is how to train both an aging workforce and the expected influx of new miners and mine managers as older workers retire. Thus, a review of some of the basic principles of adult learning may be helpful to mine trainers. This paper discusses the principles of adult learning based on research in education and psychology. It stresses the importance of taking a systems approach to training, focusing on the relationship between the environment and technology, and understanding how workers interact with both. The authors argue that the principles of adult learning and a systems approach are fundamental to the delivery of effective training in the mining industry. Examples of training programs developed by the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health are presented within two broad performance domains: routine and nonroutine skills. Basics of curriculum development are also briefly presented to provide the mine trainer with a template for program development.

Jan 1, 2002

By E. P. Youngman

Prior to 1854 the provincial legislatures in Austria enacted their own mining laws. The confusion that resulted from the existence of different codes when mining began to be conducted by modern methods forced the drafting of a law to cover all mining operations of the country. Such a general law (allegemines österreichisches Berggesetz) came into effect May 23, 1854, in the old monarchy, with the exception of Hungary, which had its own special laws. This general law of 1854 is still the basic mining law for Austria, although it has been amended and supplemented by a mumber of acts.

Nov 1, 1931

By D. Denton, M. Stickney, R. Langston

The National Institute for Occupational Safety and Health and the Stillwater Mining Company worked cooperatively with the Montana Bureau of Mines and Geology to develop a system that would collect seismic data at the Stillwater and East Boulder mines. The purpose was to obtain baseline information on the magnitude and location of mining-induced seismicity to determine if the mines needed multi-channel in-mine monitoring systems. Seismic data recorded at field sites near the mines are being telemetered via FM radio through a series of repeaters to a central recording site where the seismic signals are digitized using an Earthworm data acquisition system. The Earthworm system performs several data analysis tasks in near-real time and places raw seismic data, preliminary hypocenter locations, and magnitudes on a Website within 5 min of a seismic event. Such rapid access to seismic data allows personnel at the Stillwater Mine, Spokane Research Laboratory, and Earthquake Studies Office to evaluate seismic events quickly and respond in ways that may improve the safety of mine personnel underground. Installation of the system also broadened earthquake coverage to south-central Montana, a region previously not covered by the seismograph network.