Search Documents

By Michael J. Magyar

The Federal Bureau of Mines has developed a hydrametallurgical method to recover aluminum, aluminum oxide, and fluxing salts from aluminum salt slags. The slag is leached with water at room temperature to produce a saturated brine slurry. Screening of the slurry yields an aluminum-rich fraction that can be returned to the dross furnace. The remaining slurry is vacuum filtered, yielding a clear brine solution and an aluminum oxide filter cake. Evaporation of the clear filtrate produces a high-purity fluxing salt for reuse in the dross furnace. Over 80 pct of the metallic aluminum is recovered in the aluminum-rich oversize fraction, while essentially all the fluxing salts are recovered by evaporation. This report contains the final results of an investigation on a process research unit scale, an economic evaluation of the method, and recommendations to further improve the process.

Jan 1, 1979

By A. C. Johnson

The T. L. shaft of the Eureka Corp., Ltd., near Adams Hill, Eureka, Nev., was sunk in 1954 and 1955 to permit exploration and development of the lead-zinc-silver ore that had been indicated by drilling. This paper describes the sinking of the 4-compartment, vertical shaft to a depth of 1,127 feet and includes pertinent details of equipment, methods, and costs. A shaft crew of 10 men, supplemented by 13 hoistmen, topmen, carpenter, and shop crewmen, sank and timbered the 1,127 feet of shaft in 630 workdays. Total labor per foot of shaft was 107.95 man-hours. Supplies per foot of shaft included 20 pounds of explosives, 1.61 pounds of drill steel, and 200 board-feet of timber. Power consumption, including that required for pumping, averaged 3,726 kw.-hr. per foot.

Jan 1, 1958

By I. S. Solet

This study, of the liquidus temperatures and densities of molten alloys of zinc and aluminum was made as part of a broader investigation on refining of scrap aluminum. One of the methods of refining involves the separation of liquid and solid phases by gravity segregation and by filtration. More accurate data were required on the liquidus temperatures and the densities of molten' mixtures of the metals than were available in the technical literature. New data on the liquidus curve were obtained by thermal analysis. The new temperatures are, for the most part) somewhat higher than those reported previously by other investigators. The density of molten mixtures of zinc and aluminum were found to be less than would be calculated by assuming that the two metals occupy the same respective molal volumes in solution as they do as pure metals.

Jan 1, 1949

By W. G. Bradley

THIS PAPER describing the quarrying, mining, and crushing of gypsum at the Blue Diamond mine, 11 miles from Arden, Nev., on the Union Pacific Railway, is one of a series on gypsum mining being prepared for and published by the Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total production costs might in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By Leonard Obert

[Tng occasional. rock noises in a nice caured by brc,*ing and ripping of the back, settling, and other cailscr, are well-known tc~ a11 mining en- gineers. These noises oftcn prececte certnin tpes of rock failure as such are used to e certain event a; w:,rnlngs. Senides t5ese audible rock noisee t'nere are, l?o\;evpr, even Iprger nw.iber of' s;Lba.J^;li5le rock mis~s, which must; be piclcell UT with sole type of vi-urr,tion rnicroyhoce and qli- fied in order tnnt :hey n;ny e heard. It v:zs s~v;,yestec" Ir, an evlier ? ,I a.ldible noises Ifureau of I.lines s~zb:ic;et.iod that n stud:r of t!ler;c! *- t mig!!t be useful ir. de temining roc^ movemrnt 3 preceding failure.]

Jan 1, 1941

By W. P. Yant

Publication of lists of the devices for giving respiratory protection which have been approved by the U. S. Bureau of Mines is made periodically for the purpose of aiding consumers in procuring equipment .374/ The last published list , approved to March 15 , 1935 , appeared as Information Circular 6845 with the same title as this article . The schedules of requirements and tests which the devices must meet in order to obtain approval are published 2/6/1/8/ by the Bureau of tests the devices must Mines and are available to the public . It is pertinent to mention that the preparation of a schedule of requirements for fresh-air supply devices of the types commonly known as positive -pressure respirators , airline respirators , sand- blast helmets , and hoods , has been practically completed and will soon be ready for release to the public .

Oct 1, 1936

Reduce exposure of longwall face workers to respirable dust generated during the advancement of roof supports. Approach Identify and implement current water-application and improved support-movement practices used to lower support-generated dust. Defining the Problem Bureau studies have shown that on some longwall faces support dust can contribute over 30 percent of the respirable dust exposure of face workers. Conditions contributing to high levels of respirable dust generation during support movement are: depth of cover greater than 1,000 ft; immediate roof consisting of coal top or friable shales; and face-air velocities in excess of 500 fpm. Moreover, at most longwalls, supports are advanced on the intake-air side of the shearer as it travels with the airflow. This places the shearer operators, and in many cases the support movers, downwind of support advance, thus increasing their respirable dust exposures.

Jan 1, 1984

By William R. Vogel

The Bureau of Mines Information and Analysis organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 3291, to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral- material production or consumption.

Jan 1, 1989

Develop tools that mine personnel can use to comply with 30 CFR,Part 47. Background The new MSHA rule, 30 CFR, Part 47 (also known as the HazCom rule), requires all mines to develop a written program to track hazardous chemicals at their sites. More specifically, the rule requires that mines list all chemicals and determine which are hazardous; develop a written Hazard Communication Program; label all containers used to store hazardous chemicals; obtain or develop Material Safety Data Sheets (MSDS) for all chemicals stored or produced; provide miners with training in working around hazardous chemicals; and make information about hazardous chemicals available to all workers. All mines with six or more employees must have complied with the new rule by September 23, 2002, and mines with five or fewer employees will have to be in compliance by March 21, 2003.

Mar 1, 2003

The importance of controlling respirable dust and methane gas levels in underground coal mining cannot be underestimated. While respirable dust can significantly affect the occupational health of underground coal miners, methane gas accumulations pose significant safety concerns for these same workers. Water sprays and machine mounted dust scrubbers offer effective control of respirable dust exposures and methane gas accumulations. Water must not only be applied carefully to avoid dust rollback to the machine operator but must create sufficient turbulence to remove dead zones that could contain high concentrations of methane gas. While the flooded-bed dust scrubber has been generally responsible for decreased worker exposures to respirable dusts, this device has proved effective in controlling methane levels at the face. This paper reviews practical applications of water sprays and dust scrubbers to control respirable dust and methane gas on continuous miner faces.

To provide a faster means to open and close permissible electrical enclosures. Approach: An inspection and repair port with a multiple start thread which provides a permissible joint has been developed and tested. How It Works: The inspection port screw thread has a large pitch, which allows the port cover to be rotated from fully closed 10 fully open, in less than one revolution. See Figure 1. When the cover is screwed back in. it be-gins engagement within one eighth turn because the screw design has eight separate threads. To prevent Its unauthorized opening, the port cover has a bolt guarded by ears which accept a padlock. The threads are designed to tolerate a reasonable amount of grit without binding, although wipe-off cleanness is necessary during reassembly. Enclosures of two different sizes each fitted with the quick-access port, were

Jan 1, 1976

By J. D. Noll, S. E. Mischler

Measurement and sampling of diesel particulate matter in mine air presents a challenge due to the complexity of the diesel aerosol. The results of a series of tests carried out by the National Institute for Occupation Safety and Health, Pittsburgh Research Laboratory, in an underground mine were used to evaluate several measurement methods that are currently used to characterize particulate matter emitted by diesel-powered equipment. This paper presents an overview of these techniques and examples of the results along with a discussion of the advantages and information gained by each technique. The measurement methods discussed include particle size measurements using a scanning mobility particle sizer, total particulate matter measurements using a tapered elemental oscillating microbalance, a size selective sampling method for workplace and personal exposure assessment and a size-selective high volume sampling method for carbon analysis.

Provide ear protection which allows normal, unaltered hearing at low noise levels, yet protects the wearer from excessive noise. The Approach: A commercial earmuff with integral speakers has been adapted with a special amplifier so that low sound levels are not affected, but higher noise levels automatically reduced. How It Works: The discriminating earmuff developed by the Bureau of Mines has two modes of operation. In the first mode, where input sound levels are less than or equal to 83 decibels, the wearer will perceive noise at its actual level. For inputs in excess of 83 decibels, the second mode of operation begins and the sound perceived by the wearer is progressively attenuated, or reduced, as the input level is increased. A recognizable difference still exists between two adjacent sound levels enabling the wearer to differentiate between them.

Jan 1, 1975

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

To alleviate the hazard to personnel and danger to equipment caused by fires on large, mobile vehicles. The Approach: A system which automatically senses a fire at its early stage of development, warns the driver of the danger, and activates fire extinguishers in the zone of combustion, How It Works: The automatic fire protection system utilizes both thermal and optical sensors to detect the heat or light given off by a fire in the area of concern (Fig. 1). The system warns the driver of the hazard and then automatically extinguishes the fire with pressurized S-C class powder. The system can also be activated manually from the operator's cab or from ground level. Further, the automatic sequencing of the system can be manually overridden by the driver if he determines that the fire sensors have malfunctioned to cause a false alarm.

Jan 1, 1974

By Richard F. Link

The principal procedures for the statistical analysis of gold assay and other trace-element data depend on applying either the normal frequency distribution or the lognormal frequency distribution. The consequences of applying both methods are examined through reference to example data from United States and South African gold mines. It is concluded that for estimation of average grades, except for certain data with a very high coefficient of variation (ratio of standard deviation to mean), use of the lognormal distribution is ordinarily undesirable because bias may be introduced and little efficiency can be gained. However, if biased average grades can be tolerated, as in the examination of data from surveys in exploration geochemistry, use of the log-normal distribution may be desirable. Various statistical analyses are detailed, and the tables presented to implement the analyses are more complete than those previously published.

Jan 1, 1971

By R. V. Ramani

In this report, the application and limitation of the various equipment available for surface coal mining are discussed. The correction factors for adjusting equipment performance arising from machine design, material characteristics, and modes of operation are presented. Engineering design, pit layout and equipment selection are discussed with mathematical derivations. Two computer programs (SMCALC and SMRES) have been written to aid in pit design and equipment selection. The Strip Mine Calculation Program (SMCALC) can be used to select the bucket size and reach of shovels and draglines for various pit widths. It will also calculate the number of drills, loading shovels, trucks and bulldozers needed to achieve a production target. The Surface Mine Reclamation Equipment Selector (SMRES) can be used to select the number of bulldozers, scrapers and front-end loaders needed to achieve the desired production.

Jan 1, 1976

By C. P. Fang

"For lower stages of multinozzle micro-orifice impactors, as many as two thousand nozzles are uniformly arranged within a cluster diameter of 1.06 inches. In the impaction region the mass flowrate of the spent air increases along the radius and reaches a maximum at the periphery. This crossflow can significantly deflect the air jets of the outer nozzles, hence the characteristics of impaction changes.Investigators in heat transfer and fluid mechanics have studied the influence of crossflow on jet deflection and found the dimensionless deflection of the jet centerline X/Dn is a function of (S/Dn)(l/m) . only, here X is downstream coordinate measured from the center of the jet orifice, Sis the jet-to-plate distance, Dn is the orifice diameter and m is the jet/crossflow mass flux ratio defined as:"

Jan 1, 1989

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects world-wide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1992