Search Documents

By K. E. Robinson

This study provides an initial indication that mill tailings produced in the Coeur d'Alene Mining District of Idaho can be placed on floodplain areas in a technically acceptable manner without artificial liners and without seriously contaminating the surrounding area. Tests have shown that landfills on these unused areas can result in returning these areas to productive use. The engineering properties of mill tailings permit construction of stable embankments. Designed slope protection inhibits water erosion. Among the environmental considerations in using tailings for landfill construction are the acid and other contamination produced by tailings and wind erosion of exposed tailings surfaces. The initial results indicate that adverse impacts are not as severe as previously thought, and mitigative measures are feasible. Based on the preliminary data, and in accord with existing Federal and State waste management regulations, a conceptual design has been developed for 23 potential landfill sites in the District, which could reclaim 750 acres of floodplain. A cost analysis of landfill construction with mill tailings indicates that the method would be an economically viable means for increasing the valleywide tailings storage capacity, provided construction with slurried tailings is feasible. A Stage H study is proposed to evaluate slurried tailings as a foundation material, as opposed to hauled tailings used in this present study.

Jan 1, 1981

By F. S. Boericke

"INTRODUCTION The mineral found in natural-chromite deposits is never pure Fe0.Cr203, but rather one in which the Fe0 and Cr203 are in part replaced by Mg0 and A1203, respectively. The purest gravity concentrates from many domestic de¬posits consist of a mineral referred to as ""picotite,"" in which this isomorphous replacement is such that the ratio of chromium to iron is low. The Bureau of Nines has investigated methods of chemically beneficiating ores that contain too much iron to be classed as ""high-grade"" chromite 3/ Early investigations 4/ demonstrated that high-iron chromite or picotite ores can be roasted with carbon to obtain selective reduction of the contained iron, and that most of this reduced iron can be removed by acid-leaching the roast products to produce residues of higher chromium-to-iron ratios. tests 5/ indicated that commercially acceptable reaction rates cannot be obtained at roasting temperatures below 1,3000 C., using solid carbon as reducing agent. By this high-temperature reduction and subse¬quent acid-leaching, however, all ores investigated, regardless of the original composition, readily yielded residues considerably better than the minimum specifications for high-grade chromite.In an effort to obtain satisfactory reduction of chromite at lower temperatures, liquid and gaseous seducing agents were tested with varying success. Of the several reducing agents used, methane appeared to be the most promising and was shown to be highly effective at temperatures between 1,000º and 1,100º C., roughly 300º below the roasting temperatures necessary in solid carbon reduction. Further experiments indicated that mixtures of methate with some diluent (hydrogen or other nonoxidizing gas) gave better reduction than did methane alone."

Feb 1, 1946

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coals; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the fourth of a series of reports giving the results of studies by counties under phase (1) of the investigation. It covers Armstrong County, Pa., which comprises parts of the Foxburg, Clarion, Brookville, Kittanning, Bural Valley, Smicksburg, Freeport, Elders Ridge, and Indiana quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and more than 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside the outcrop were measured by planimeter on the base maps, Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By J. L. Eakin

Systematic flooding was introduced into Nowata County, Okla., in May 1931. The results of this means of stimulating the nearly depleted Bartlesville reservoir in the county has been the subject of four Bureau of Mines Reports of Investigations.2-5/ This report presents a discussion of four full-scale water-flooding projects in the Delaware-Childers field and 1 pilot project in the Curl Creek field (fig. 1). All five plants have been in operation for only a few months. Although substantial increases in the rates of oil production have been obtained 1 by the injection of water, the projects are of particular interest at this time because of the novel methods of operation and new equipment that are being employed. One project utilizes a portable "package" plant designed for a pilot operation. All of the controls for this project are centrally located. The design makes it possible to remove the test plant to another location if the project is unsuccessful or if the unit is to be replaced by a larger plant. This project also utilizes diatomaceous-earth filters successfully for the first time and makes use of plastic pipe. Another novel feature of the operation is the aeration of Arbuckle limestone water through an airlift in the supply well.

Jan 1, 1955

By John W. Buch

Hydraulic cutting tests made on samples of Pennsylvania anthracite (3,700 psi and 260 gpm) were promising enough for the Bureau to establish a full scale experiment in an anthracite mine. Water pressure and quantity for mining anthracite were arbitrarily established at 5,000 psi and 300 gpm (1,000 hp). For full-volume flow, hydraulic pressure is controlled by orifice size with the displacement pump. The hydraulic jumbo was designed for maneuvering on pitches from 0° to 20° in any direction and for a coalbed ranging in thickness from 10 feet 6 inches to 15 feet. All motions of the jumbo are by oil hydraulics. Jet flow is controlled (start-stop) at the face, through an interlocked pushbutton system. One button is in the operator's cab; one, at the pump station; and one (a safety shutoff), near the mining face. To December 1962, 7,400 tons of bed material had been mined at an average rate of 0.800 ton per minute, with an average power requirement of 14.125 kilowatt-hours per ton. In January 1963, the objective was changed from an engineering-development basis to a research basis--to determine, ultimately, the most efficient level of operating characteristics for maximum response, as measured by mining-out rate. This research phase of the project is not yet complete, but conclusions, and the method of arriving at them, will be made the subject of another Bureau publication. It should be noted that as of December 1963 nearly 13,000 tons of bed material had been mined, at rates as high as 1. 3 tons per minute for a complete face advance.

Jan 1, 1965

By Herbert H. Einstein

Rock mass deformability is commonly predicted using correlations with RQD or other indices of rock mass quality, or by extrapolation from large in-situ tests. Based on the probabilistic description of rock masses empirically developed in Part I a new approach was attempted in modeling for predictions of deformability. This approach decomposes the rock mass into spatially variable joints described by probability distributions, and intact rock blocks. Stiffnesses and elastic parameters are associated with the joints and intact blocks respectively, and deformations built up by adding the contributions of each. This model allows relaxation of many of the simplistic geometric assumptions which constrain parallel attempts to model deformation in rock masses. The model has been applied to four standard cases in order to test its results against previously existing models, and to check whether it replicates empirical correlations. When joints are taken as parallel, common empirical correlations are closely approximated by the model output. However, the closeness to empirical correlation breaks down when variability of the jointing geometry is increased.

Jan 1, 1979

These proceedings consist of papers presented at two Bureau of Mines Technology Transfer Seminars in early 1980 for the purpose of disseminating recent advances in mining technology related to surface coal mining reclamation.

Jan 1, 1980

By John J. Ginty

The objective of the work reported herein was to evaluate state-of-the-art repeaters used in wireless communications to determine their suitability for use in extending the range of portable and mobile communications in underground mine applications. The scope of the work included wireless repeaters in the frequency range from LF (500 kilohertz) up to the one giga-hertz range. These repeaters included not only single-channel repeaters, that is F1/F1 repeaters for short range simplex party line communications, but in addition, F1/F2 type repeaters currently commercially available in the HF, VHF and UHF bands.

Jan 1, 1975

By Thomas E. Howard

Man has been engaged in the construction of tunnels in. rock for several thousand years. During that time, methods of tunneling have changed drastically. Hordes of men chipping away at the tunnel face have been replaced by mechanical drills and explosives and by tunnel boring machines. Spoil is no longer carried on the backs of humans, but is now removed by trains, trucks or conveyor systems. These and other changes have had the effect of greatly increasing the rate of tunneling, while at the same time, greatly decreasing the potential dangers to workmen. Although the techniques, equipment and material used for tunneling are being continually improved, rock tunneling is still a slow and expensive process. Significant improvements and innovations are needed to reduce the cost and time required for tunneling if we are to fully utilize the subsurface to aid in the solution of urban problems and in the conservation of resources. This report is intended to facilitate the orderly development of tunneling technology by focusing attention on the inadequacies of rock tunneling and the improvements that are needed. The data presented were derived from the results of a comprehensive questionnaire that was completed during the summer of 1969 by more than 600 individuals and organizations in 17 countries. Table 1 lists the countries and the number of replies from each. Appendix A contains a summary profile of the national responses, while the text presents the results and a brief analysis of the conclusions that might be derived from the data in the questionnaire. The data shown in Appendix A represent the consensus opinion of each of the 17 nations without regard to the number of individual replies or the amount of tunneling activity that is represented. The national consensus was determined for each country by a plurality of the individual responses, in some cases modified by the opinion of the rapporteur. Tire above procedures can lead to situations which are misleading. For example, experience and activity arc a rational basis for analysis; but, if national replies are weighted on this basis (i.e., number of responses), informed and valuable opinion of less active countries would probably be overwhelmed and lost. In analysing the data on the basis of national responses without weighting, it becomes apparent that many of the same problems exist under a given set of conditions regardless of the number of tunnels that have been driven.

Jan 1, 1970

By F. du Breuil

BCR National Laboratory (formerly Bituminous Coal Research, Inc.), under a USBM con­tract (originally with the Department of Energy), monitored the installation and operation of a computer-based belt-monitoring and control system at the Barnes & Tucker Coal Co. Mine No. 20, Ebensburg, PA. The system installed was the National Coal Board's Mine Operating System (MINOS) coal transport monitoring and control system. The program objec­tive was to document (1) the installation requirements for a conveyor control system, (2) the operating experience with the system, and (3) the impact of monitoring and control on mine operation. Analysis of the system operation indicates that monitoring and control did improve belt availability significantly, and reduced downtime associated with belt delays. Economic analysis showed the increased belt availability would potentially result in significant production increase, and, therefore, excellent payback on the initial investment. The system performed satisfactorily, was well accepted by the work force, and did not increase the maintenance workload.

Jan 1, 1987

By F. L. Wideman

This report describes the sinking of No. 3 shaft at the Westvaco mine. It is one of a series of publications of the Bureau of Mines on mining methods and practices in the United States. The Westvaco mine is in Sweetwater County, Wyo., approximately 23 miles northwest of the town of Green River (fig. I), There are no permanent habitations in the vicinity of the mine, and employees live in Green River or Rock Springs, Wyo., 14 miles us t of Green River. The mine plant is on a windswept, treeless plain, from which low buttes and flat-topped ridges rise. The altitude at the collar of No. 3 shaft is 6,351 feet. The climate is arid, with temperatures as low as 40° below zero in the winter. Blacks Fork, a tributary of the Green River and a perennial stream, flows near the mine.

Jan 1, 1959

This publication contains 10 papers presented at a symposium on ATRS systems in Charleston, WV, on June 23, 1983. Included are papers by MSHA Technical Support (Roof Control), West Virginia Institute of Technology, the Bureau of Mines, and seven roof bolter manufacturers and/or designers of ATRS systems. These papers summarize the most recent developments in ATRS technology and can serve as a guide to potential designers, developers, and users of ATRS systems.

Jan 1, 1985

By J. A. Holmes, EDWARD C. FRANKLIN, RALPH A. GOULD

The commission may be permitted to express its earnest hope that the litigation which comes to an end with the findings and recom- mendations herein set forth will be considered by both parties to the action as definitely and equitably decided. The commission trusts that its work will show the value of the commission form of settlement and that its work will serve as a prece- dent to be followed in disputes relative to technical subjects. If the work of the commission is productive of a tendency on the part of technical litigants to avoid the use of the courts for the settlement of disputes it will not have been done in vain. Such tendency will surely grow and ultimately such differences will be arbitrated by technically trained men without recourse to the courts of law. Appended to the report of the findings of the commission are to be found the detailed reports covering the several lines of inquiry and investigation carried on by the commission and upon which its findings are based, and also a detailed statement of the fiscal affairs of the commission. A word of explanation is necessary in regard to the fiscal statement. While each party to the litigation has agreed to bear one-half of the expense of the investigations of the commission, it will be noted that the Selby Smelting & Lead Co. is credited with $21,000, while Solano County is credited with but $6,000. In order that the investigations of the commission might go forward without interruption the Selby Smelting & Lead Co. has generously supplied funds at the times they were needed. This assistance has been

Jan 1, 1915

By Charles G. Maier

"INTRODUCTION The use of thermodynamic calculations to answer practical problems in metallurgy, especially those that are relatively difficult to test experimentally, is rapidly becoming a conventional method of procedure. Nevertheless, these methods cannot he applied effectively until the fundamental thermodynamic constants used for them have become available either by direct experiment or by recalculation of data already existing in more or less undigested form.In an attempt to collect such data far the compounds of lead and the antimony group the incentive has been to make a preliminary survey that will disclose the gaps or questionable phases of available information and to collect data that may be used to answer certain rather practical problems presented by operating metallurgists.This report comprises three sections; the first gives the basis of selection of the constants which may now be given or estimated, and the later sections discuss the application of the figures obtained to two of the more interesting problems.The reader will discover that many of the quantities involve critical study of a number of more or less discordant observations. Although certain data could be rejected on the basis of thermodynamic comparisons, it must not be overlooked that many of the figures are the results of rational estimates rather than exact experiment. The use of thermodynamic methods to control and partly authenticate such estimates is one of its most valuable characteristics for the practising metallurgist or chemist, who cannot check by direct experiment each property of the materials which he converts to usable form.Nevertheless, while it is definitely possible in certain instances that the final figure selected for the heat or free energy of a process or substance may be in error by as much as a few hundred to a few thousand calories per formula weight, questionable figures are usually revealed by the thermodynamic calculations made. When quantities of such degree of accuracy are, and they often must be, used for estimating an unknown reaction, the result often gives no more than the order of magnitude of the desired quantities. Yet even in these extreme cases the answer is far more reliable and valuable than an unordered guess or a conclusion based on incorrect data."

Dec 1, 1934

By John W. Chandler

The property of the lava Cap Gold: Mining Corporation is in the Nevada City-Grass Valley mining district about 5 miles east of Crass Valley, Calif. At present (July 1940) the plant is mining end milling about 390 tons of gold-silver ore a day; about 310 men are employed. This paper describes the mining methods used and presents mining costs for 1939, when 60,704 tons were mined by cut-and-fill stoping and 55,676 tons by square-setting.

Jan 1, 1941

By J. W. Howland

To determine their effectiveness in different climate and soil conditions, a demonstration of dozer blades specifically designed for recontouring mine spoil was conducted at an East Texas surface coal mine. The specialized equipment included a 48-foot angle blade, a modified 24-foot "U" blade, a 13-foot deep "U" blade, and a 24-foot grading bar. Both the 4b-foot and the 24-foot "U" blades were mounted in a two-tractor, single-operator configuration. To meet flotation problems common in this mining region, a 22-foot lightweight blade was developed and demonstrated for use on a 400-430 hp tractor. The demonstration involved 1,185 acres and showed a 50% reduction in reclamation costs and a 47% reduction in fuel requirements for this mine site over conventional equipment. Improved equipment, trained operators, good supervision, and improved monitoring techniques contributed to the savings. Procedures and results of the demonstration are presented and analyzed here along with guidelines for application of findings.

Jan 1, 1981

This report summarizes the cost of U.S, mining and milling industry compliance with the Environmental Protection Agency (EPA) interim water quality guidelines for waste discharges. Applicable excerpts from Public Law 92-500 are stated and interpreted in conjunction with the guidelines being used for implementation of the law. Over 200 U.S. Army Corps of Engineers applications for discharge permits were used to develop the quality and quantity data base needed to estimate the cost to comply with EPA guidelines, Cost of three basic treatment methods were considered: Aeration, addition of lime, and sedimentation. From the process design, cost-capacity graphs were developed to consider maximum flow rate, maxi lime addition, and average flow rates. The graphical method used in this evaluation should provide a reasonable guide to the effect of waste treatment and, therefore, Public Law 92-500 and corresponding EPA guidelines on the mineral processing industry. The cost of complying with the EPA guidelines will have the effect of prompting the mining industry to minimize the production of waste water and of undertaking some additional treatment, Two case studies are presented to illustrate efforts that might be fruitful for minimizing waste water production and for treatment of combinations of acid mine drainage, mill wastes, and metallurgical process wastes when treatment is deemed necessary.

Jan 1, 1975

By E. P. Ferrero

Analyses of 38 crude oil samples from 25 fields in Algeria, Libya, and Nigeria are presented in this report. The 38 crude oils are listed alphabetically by country and field. Also shown are the geographic and geologic sources of the samples analyzed, the companies that supplied the samples, the general characteristics and analytical and computed data, and the production for the fields from which the samples were obtained.

Jan 1, 1966

By E. P. Ferrero

Analyses of 38 crude oil samples from 25 fields in Algeria, Libya, and Nigeria are presented in this report. The 38 crude oils are listed alphabetically by country and field. Also shown are the geographic and geologic sources of the samples analyzed, the companies that supplied the samples, the general characteristics and analytical and computed data, and the production for the fields from which the samples were obtained.

Jan 1, 1966

By Thomas A. Milne

As part of the broad program to improve the safety of underground coal mines, the Pittsburgh Mining and Safety Research Center sponsored several detailed studies on the inhibition of coal dust-air explosions. The present study was one of these. The goal of the research was to advance the development of improved coal-dust explosion inhibiting agents by determining, on a laboratory scale, the basic chemical processes involved in the inhibition of coal-dust flames by dry-powder agents. B. Our Approach Neither the basic molecular processes involved in coal combustion, nor the molecular mode of action of dry-powder agents, are known with certainty. Our approach, therefore, involved the direct determination, by sampling techniques, of species behavior in small, aerodynamically simple flames. To further aid in separating behavior of coal and dry-powder inhibitors, the latter were studied in CH4-air flames.

Jan 1, 1976