Search Documents

By M. Paczkowski

The use of inert gas systems to extinguish mine fires has been the subject of research for some time in the United States. In some European countries, it is an established practice. Tests were conducted with the CMI Inert Gas System (CMI), which is being used by the Polish mining industry. This system utilizes a modified jet aircraft engine and afterburner as a compact source of combustion products with a very low (less than one percent) oxygen content. Water injected into the combustion products stream provides evaporative cooling and forms a mist with a high cooling capacity. The CMI system was used under controlled conditions to extinguish coal pile fires at the U. S. Bureau of Mines Experimental Mine in Bruceton, Pennsylvania. The test results show that the CMI system can be used conveniently to extinguish fires quickly and to maintain an inert atmosphere in the fire zone to prevent re-ignition.

Jan 1, 1982

By Edward W. Parsons

The explosive-anchored rockbolt was field tested in six mines where rock conditions varied from incompetent shale or mudstone through fairly soft sand-stone to firm sandy shales. The purpose of the testing was to document, under a wide variety of conditions and in comparison to other rockbolt anchors, the quality of the anchorage produced by the explosive-anchored bolt. In addition, the length, strength, and design of the explosive charge necessary to produce positive anchorage up to the yield strength of the weakest component of the bolt were determined. A l4-inch length beaded explosive charge was found to be suitable, in general, in relatively weak strata, and the length can be reduced in more competent strata. Of the 127 explosive?-anchored bolts tested, 118 bolts produced an evaluated anchorage in excess of 17,000 pounds. Only 4 of 43 expansion-shell bolts and 4 of 14 wedge bolts produced anchorage this good. In preliminary tests, properly coupled explosive-anchored bolts did not ignite an explosive gas mixture. Some minor phases included in the investigation were as follows: (1) effect of explosive-anchored rockbolt on surrounding rock; (2) effect of time on anchored bolts based on torque tests; (3) effect of submersion in water on rockbolt anchorage; (4) pull tests to higher loads; and (5) ignition tests.

Jan 1, 1965

By S. P. Kinney

The Department of the Interior has recently investigated the atmospheric conditions in tunnels of the Union Pacific Railroad in Utah and Wyoming , by observations made from the cabs of freight locomotives . This work was conducted by the Bureau of Mines at the request of , and in cooperation with , the Union Pacific Railroad Co .. and was brought about by several accidents to members of engine crews while passing through tunnels , from pollution of the tunnel air by exhaust gases from freight locomotives . The object was to determine the cause of gassing accidents , by examining into composition of the air in locomotive cabs while passing through railroad turmels ; to learn the effect of these conditions on the engine crew; and to provide a means of protection for the men so exposed . Gas samples and temperature readings taken in the cabs of locomotives were used in studying the atmospheric conditions to which the locomotive crews were exposed . The symptoms and the physiologica effects produced in men exposed to the atmospheres encountered were studied . The pulse rates and body temperatures were taken , and the determinations of the carbon monoxide content of the blood were made . Various methods for the prevention of gassing and for the protection of men therefrom were considered and tested , among which were the use of mechanical devices for deflecting the smoke away from the engine cab, and the use of various types of gas masks and breathing apparatus . While this investigation is a part of the safety work of the Bureau of Mines in connection with hazards from atmospheres containing carbon monoxide ( CO ) , the results are of particular value to railroads operating steam locomotives through tunnels , and are also valuable to other industries where atmospheres having poisonous gases or of a high temperature and humidity may be present . The results may be summarized as follows :

Jun 1, 1923

By Kenneth Wardell

Criteria have been fully developed for determining the optimum size of oil and gas well blocks. The criteria lead to the formation of well barrier pillars which are, of themselves, inherently stable and take account of variable mine roof and floor conditions. The criteria ensure, through considerations of ground movement, that strains transmitted to well casings, are within tolerable limits of casing specifications. The criteria cater for well barrier pillars in multi-seam mining situations and where previous old mining has taken place. The criteria maintain flexibility in being adaptable to local mine design situations. The criteria are applicable to proposed extraction thicknesses up to 15 feet at depths up to 2,400 feet. The criteria are related to producing wells and to abandoned wells. In the latter connection, various states of well abandonment are recognised.

Jan 1, 1980

By W. J. Long

As a part of the strategic mineral exploration program, examining engineers of the Bureau of Mines collected samples of ore from four manganese properties in Yavapai, Yuma, Maricopa, and Mohave Counties, Ariz. As all of the ores were too low in grade to be acceptable by manufacturers of ferromanganese beneficiation studies were made to determine the amenability of the ores to concentration.

Jan 1, 1948

By J. O. Lewis

In its efforts to reduce waste, and increase efficiencyin oil production, the Bureau of Mines is investigating methods of increasing the recovery from the underground sources of supply, which are the foundation of the petroleum industry and the many allied industries wholly or partly dependent on it. In the face of a demand that is increasing faster than the production and that, in the consensus of opinions of well-informed authorities, is soon likely to outstrip the productive capacity, it is well to consider whether it is not possible to extract more oil from the known sources of supply. It is universally acknowledged that by the usual production methods much oil is left underground, the general opinion being that at least 50 per cent of the oil in a field remains unrecovered when the field is abandoned as exhausted. From the writer's own investigations he believes the average recovery is even less, and if any considerable portion of this oil being left underground could he made available it would have a tremendously favorable influence on the petroleum industry and all the industries dependent on it. In this publication are considered the principles involved in increasing recovery and methods of extracting more oil from the oilbearing formations than by the usual ways of producing. These methods are: The use of gas or vacuum pumps, forcing compressed air or gas through the oil-bearing formations, displacing the oil by water, and better utilization of the natural pressures in the oilhearing formations. Especial attention is being given to a processcommonly known as the Smith-Dunn-for forcing compressed air through oil-bearing formations because it is believed to hold most promise for the future.

Jan 1, 1917

By Raymond B. Ladoo

"The recent discovery and exploitation of petroleum territory have resulted in the enactment of new petroleum laws in most of the South American Republics. The activities in the discovery of these new fields were engendered by the knowledge of the fact that present producing fields must within well defined periods be exhausted. Oil operators were willing to take the initial steps in exploitation in the absence of legislation that applied strictly to petroleum operations. The enactment of modern legislation in many of these Republics encouraging and protect¬ing exploitations may cause tremendous oil activities in these countries, and the results may be comparable with the magnitude of the undertakings and the prestige of the companies now entering this territory.These, oil fields are admirably located for convenient distribution of petroleum by water to all the Nations using oil as fuel for shipping and industrial concerns. The oil markets of the western coast of South America will derive immense benefits from the Panama Canal. This navigation route brings these markets into direct ocean shipment with the Atlantic coasts of the Western and Eastern Hemispheres.One deterrent to oil production in the Republics of South America is the want of inland. transportation facilities, but the recent laws of these Republics without exception provide for acquiring rights of way for pipe lines and other modes of transportation; and doubtless the great interests and. syndicates already operating in these regions will, as production increases, provide ample pipe line transportation sufficient to convey to the coast the oil produced. It way be assumed, from the legal guarantees afforded, and from operating equipment and machinery that are now being concentrated that refineries will be erected at shipping points for the purpose of making these petroleum products accessible to the world."

May 1, 1921

By Forrest T. Moyer, J. I. DAVIS, JOSEPH H. SCHUSTER, E. K. ELSNER

The National Safety Competition conducted by the Bureau of Mines, United States Department of the Interior, is held each year for the purpose of promoting safety in the mineral industries of the United States. Since the program was inaugurated in 1925, twenty-three safety competitions have been held. This publication is a report of the results of the contests held in 1944, 1945, 1946, and 1947. The names of plants that have been awarded "Sentinels of Safety" trophies and Certificates of Achievement in Safety dur- ing these years, together with a summary of their achievements in injury prevention, are listed. Statistical data covering the injury experience of all plants entered in the annual contests also are included in this publi- cation. The injury statistics of these plants, arranged in the six groups of the competition, are the only data on injury severity at mineral operations available to the Bureau of Mines. Interest in the National Safety Competition has increased steadily. The number of participating plants has increased from 210 in 1925, the first year of the competition, to the record number of 494 in 1946. The widening scope of the competition means that a steadily increasing number of the mines and quarries in the United States are participating in a program that will supplement their other activities in promoting safety. Safety competitions have long been recognized as instrumental in stimulating and holding the interest of employees and officials in accident-prevention work. During the years covered by this report, conditions in the mineral industries of the United States were hardly conducive to setting records in accident prevention. During the war years, handicaps were especially severe- loss of skilled employees to the armed forces or to higher-wage war industries, greater production by a smaller force of workers, relatively high rates of labor turn-over, the longer workday in effect through 1944 and 1945, and difficulties in obtaining repairs and replacement for badly worn machinery. Even the immediate postwar period has brought no abatement of the tremendous pressure upon the mineral industries for greater production. Although there was a decrease of 18 in 1947 from the record enrollment in 1946, these oper- ations worked 160,525,025 man-hours, the greatest number of man-hours of exposure to mining hazards in any year of the contest except 1942. Despite the accelerated pace at which the mineral industry worked during the 4 years covered by this report, participants in the National Safety Competition have achieved creditable performances in the promotion of safety. In fact, the injury-severity rate in the enrolled plants in the 1947 contest was 7.315 days for each thousand man-hours worked, the lowest by far in the history of the National Safety Competition. The injury-frequency rate of 42.155 for each million man-hours of exposure to mine hazards in 1947 marks a favorable trend downward from the rate of 50.577 in 1946, which was the

Dec 1, 1949

By William R. Barton

Dimension stones, with their almost infinite variety, have a broad range of properties and uses. Natural stone was beyond doubt the first mineral commodity used by man. Today dimension stone has widened to encompass building exteriors and interiors, decorative and ornamental modes, statuary, monuments, paving, curbing, flagging, roofing, and miscellaneous categories such as blackboards, surface plates, and honestones. For many purposes, it competes with greater or less success with alternate materials such as concrete, metal, brick, plastic, or glass. The almost ubiquitous geographic distribution of stone resources is the basis for a dimension stone producer industry in almost every State and in almost every land. In the United States, alone, dimension stone sold or used by quarries is valued at 2 million to 3 million dollars annually. Mining, finishing, transportation, and use technology have been modernized, resulting in a broader spectrum of stone products and new adaptions in use. Increased efficiencies also have been reflected in costs and prices and, coupled with gains that should be realized from current research, auger well for continued vitality of the ancient and honorable dimension stone craft.

Jan 1, 1968

By Alan A. Campoli

OD March 20, 1989, a meeting was held at the U.S. Bureau of Mines Pittsburgh Research Center at the request of Senator Pete V. Domenici of New Mexico. The purpose of the meeting was to engender a technical relationship between the National Laboratories and the minerals industry. During the meeting, the Director of the Bureau of Mines, T S Ary, suggested that since the Bureau is the focal point for mining research in the United States, it would be appropriate for the agency to act as the liaison between the National Laboratories and the minerals industry. As the first step in this process, the author was selected to perform a 6-month investigation to better define the proper role of the Bureau in this area. As part of the investigation, the mining and mineral-related technology available at 21 major U.S. Department of Energy (DOE) Research Laboratories was reviewed. It was assumed that the broad range of scientific and technical areas covered DOE research would provide fertile ground for mining-related technologies. It was hoped that the applicability of DOE research to this liaison effort would be indicative of Federal laboratories in general.

Jan 1, 2011

By Robert F. Randolph

Introduction This paper is a descriptive analysis of injuries and fatalities at small surface bituminous coalmining companies in Pennsylvania. The purpose of analyzing a specific industry sector and location is to identify issues that might be missed in a wider analysis. Other studies of small mine safety (e.g., Peters and Fotta, 1994, Randolph and Boldt, 1997) have shown that the relationship between safety and mine size is not a simple one. Some injury types occur at higher rates at small mines, while others occur at lower rates. Consequently, an analysis limited to a specific type of mining can help identify hazards and issues specific to that sector. The results of this analysis will be useful for directing training, intervention, and research efforts towards the most prevalent causal factors and incident types. Procedures and Definitions Data sources The primary sources of data for this analysis were files provided by MSHA containing information collected under Title 30 Code of Federal Regulations, Part 50. These files, commonly referred to as “Part 50 data”, are provided though MSHA’s Program Evaluation and Information Resources directorate. Two primary types of injuries were selected from the Part 50data: Fatalities (MSHA “degree of injury” code 1) and lost-time injuries, otherwise known as nonfatal with days lost (MSHA “degree of injury” codes 2 through 5). Lost-time injuries involve either actual days away from work or days of restricted activity or both. Fatality and lost-time injury incidence rates were calculated using the standard MSHA formula: Number of injuries per 200,000 employee-hours. Additional information on company sizes and mine ownership was provided by the Pennsylvania State University College of Earth and Mineral Sciences. Time span A five-year time span was selected for this study. More than a single year of safety experience is usually needed to capture a broad range of incident types. Many types of injuries, especially fatal injuries, can be extremely rare, and may be missed if too short a time span is selected. However, a time span that extends too far back may begin to suffer historical threats to validity. That is, incidents that occurred several years ago may be caused by hazards that have since been remedied or may be related to mining practices and conditions that no longer exist. A five-year span offers a practical compromise between these two concerns. Consequently, the MSHA Part 50 data files from 1993 through 1997 were used. The 1997 file was in “preliminary” form at the time of the study, so small variations from the final 1997 “close out” file can be expected. Based on past experience, we do not expect the close-out variations to have a significant impact on the findings.

By C. M. Harrer

The location, features, qualities, and extent of iron occurrences and the associated resources--limestone and dolomite, bentonite, coal-lignite, petroleum and natural gas, power, and water--are evaluated. The results of pioneer beneficiation tests on South Dakota taconite are discussed. In addition, pertinent features of taconite development, cost factors, the Western and Central United States trade area and markets are reported. The State's production of iron ores until 1963 has been small and for purposes other than the manufacture of iron. This investigation disclosed the probability of large resources of taconite in Pennington and Lawrence Counties. The average iron content is 29 percent, and a 65-percent or better iron concentrate might be produced. Ample resources are available for mining and processing taconite. An investment of at least $26 million would be required for a plant capable of turning out 1 million tons of agglomerated iron concentrate per year. The feasibility of such an enterprise is indicated, but intensive investigation and research must be completed to justify such an investment,

Jan 1, 1966

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

By James H. Russell

The Bureau of Mines used a statistical approach to evaluate the effects of temperature, current density, and composition of the electrolyte on the purity of boron prepared by electrolysis of a fused mixture of boric oxide in potassium fluoborate. The quadratic equation which best fits the data was calculated for a temperature of 650° to 850° C, a cathode current density of 40 to 1,150 amp/ft2,and a boric oxide content of 0.3 to 7.1 molal. The best products, better than 95 percent boron, were obtained when the current density was less than 2 amp/ft2 and the boric oxide content was less than 2 molal.

Jan 1, 1967

By L. J. Prosser, Robert Anderson

Advance knowledge of roof conditions can lead to improvement in roof control strategies that will reduce roof falls and ultimately will reduce injuries to mine workers. J.H. Fletcher and Company, in cooperation with West Virginia University, has been developing a system to meet these needs by collecting torque, thrust, and rotation speed data during drilling operations. Recent improvements in analysis algorithms to detect anomalies in the roof structure as well as various display enhancements for real time mapping and evaluation of roof structures have been incorporated into current Fletcher Information Display system. The unit has also been housed in an explosion-proof container to allow use in coal mine applications. Recently, the system has undergone extensive field trials in several limestone mines and one coal mine. During these trials, the National Institute for Occupational Safety and Health assisted Fletcher in verifying the accuracy of the roof mapping capability of the system by comparing the display information to bore hole scoping observations and drill corings. It was concluded from this assessment that the intelligent drilling system can complement scoping and core analysis to provide a more complete picture of roof strata and is capable of seeing features or conditions that are not always obvious in these more traditional methods.

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1[M] sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250°C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 2010

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests. Each ore is an individual problem until the association of the gold has been determined. Knowing the problem through the interfering minerals or elements, the solution often is only the application of part of a former known practice as an auxiliary or additional feature. In the treatment plan for most gold ores, it has been the custom to try each of the usual recovery methods or combinations thereof, accepting the best results on a basis of the lowest cost. A better plan includes knowledge of the association of the gold and the various minerals from which it is to be recovered. This presents reasonable foresight into the problems that should be expected and permits some provision for avoiding probable difficulties. The preliminary work should include: Determination of the percentage of free gold with classification showing size of gold particles to be expected; determination of the percentage of gold associated with each mineral and whether it be freed from the mineral by crushing; and an analysis of representative samples of the ore to include other valuable minerals and the form in which they occur.

Jan 1, 1934

Prevention of coal-mine explosions depends largely upon thorough knowledge of the causes that initiate explosions. A review of coal-mine explosions in one geographical area when supplemented by nationwide data of similar nature, should serve as a guide for the adoption of measures for explosion prevention. Explosions in bituminous-coal mines of the United States during the 10 years ended December 31, 1932, ranked third in the causes of fatal accidents and constituted 16.1 percent of all fatal accidents in bituminous mines. Kentucky now ranks fourth in coal output in the coal-producing States of this country; a study of the coal-mine explosions in this state will be of definite interest locally among coal-mining people, as well as to those in the coal-mining industry who are concerned in preventing coal-mine explosions. This circular reviews gas and dust explosions in Kentucky coal mines to show their hazards, to point out the influence of certain factors in causing explosions, and to indicate the effectiveness of preventive measures.

Jan 1, 1934

By Jon K. Ahlness

The Bureau of Mines conducted laboratory and field experiments to determine tne amount of permeability reduction in uranium sandstone after its exposure to different drilling fluids. Seven polymer and two bentonite fluids were laboratory-tested in their clean condition, and six polymer fluids were tested with simulated drill cuttings added. Sandstone cores cut from samples collected at an open pit uranium mine were the test medium. The clean fluid that resulted in the least permeability reduction was an hydroxyethyl cellulose polymer fluid. The greatest permeability reduction of the clean polymers came from a shale-inhibiting synthetic polymer. Six polymer fluids were tested with simu-lated drill cuttings added to represent field use. The least permeability reduction was obtained from a multipolymer blend fluid. A field experiment was performed to compare how two polymer fluids affect formation permeability when used for drilling in situ uranium leaching wells. For this test, the polymer fluid with the best laboratory results (multipolymer blend) was compared with a commonly used polymer fluid (guar gum) that gave poorer laboratory results. When fluid injection rates for the four wells drilled with the guar gum were compared with those for the four drilled with the multipolymer blend, no statistically significant difference was found.

Jan 1, 1984

By H. Tomlinson

Fatalities from falls of roof and coal are responsible for the death Of more than 1,000 miners annually in the bituminous coal mines of the United States, or practically one-half of the total fatalities In and about these mines. The men are killed by falls singly or in small groups and little or no publicity is given these accidents as they lack the spectacular features of gas and dust explosions. As a result, the public and even the miners have the impression that accidents from falls of roof and coal are just one of the unavoidable hazards of the coal-mining industry. This belief is not true. Accidents caused by falls can be avoided largely by the application of sound engineering principles, by education, and by proper leadership in the industry, just as gas and dust explosions and accidents caused by explosives have been reduced in recent years. The necessity for studying falls of roof and coal becomes apparent by referring to the following data from a table by Adams and Chenoweth:3

Jan 1, 1933