Search Documents

By J. W. Paul

The United States Bureau of Mines has made a study of roof control in 68 mines operating in the Pittsburgh coal bed in Pennsylvania, West Virginia, and Ohio. In making these studies, much information was also obtained on various exact methods of development and pillar extraction as practiced by this large group of mines. It is proposed in this paper to describe these methods, by which this group of mines in 1931, a year of reduced industrial activity, produced 28,123,000 tons of bituminous coal - 7.4 percent of the national production for the same year and an amount equal to the combined production of the coal mired in the States of Alabama, Colorado, New Mexico, Utah, and Wyoming. The results of these studies, insofar as they pertain to the prevention of injuries from falls of roof, have been published by the Bureau of Mines. In this paper only a few mines typical of each system will be described; however, should the reader be interested in other details with respect to these mines, he may refer to the following publications: T.P. 522, 1932, 43 pp. Falls of roof and coal in mines operating in the Pittsburgh coal bed in Marion and Monongalia Counties, W. Va., by J. W. Paul and J. N. Geyer.- A study of nine mines in these two counties of northern West Virginia.

Jan 1, 1935

By R. W. Van Dolah

An investigation was made of the distances over which sympathetic detonation of ammonium nitrate (AN) and ammonium nitrate-fuel oil (AN-FO) might be expected. Large-scale gap tests used two types of AN-FO donor charges in three sizes with AN, both at ambient and elevated temperatures, and AN-FO acceptor charges. Donor sizes were varied to test the validity of a scaling law commonly used in quantity distance tables. The up-and-down experimental design was chosen to determine the 50-percent initiation point efficiently. The acceptor charges were instrumented to indicate initiation and to determine detonation velocity. Other electronic techniques for measuring the rate of growth, stability of detonation, and detonation pressures were employed. Air shock and fragment velocities between charges were measured by electronic and photographic methods, and determination of side-on air-blast pressures and impulse duration were made for about half the shots. Separation distances between donor and acceptor were found to be larger than anticipated both for the AN and the AN-FO. With AN-FO acceptors and a 16-gage steel faced donor, one initiation occurred at a separation of 53 feet or nearly 16-charge diameters; with AN, initiation occurred at 4 to 5-1/2- charge diameters.

Jan 1, 1966

By E. W. Dean

A previous report of the Bureau of Mines* has supplied data for the physical and chemical properties of samples of crude petroleum produced in the eastern fields of the United States. It was issued as a preliminary chapter of a bulletin which is to cover the results of a survey of the entire country. The present report is a second preliminary chapter including figures that are available for the producing fields of the Rocky Mountain district. Work is being continued. with a series of samples from the States of Kansas and Oklahoma which will be described in a third preliminary chapter, to appear at a subsequent date. Acknowledgments. The obtaining of samples was rendered possible through the courtesy of representatives of a number of producing and refining companies operating in the Rocky Mountain district. The Bureau hereby acknowledges its appreciation of the hearty spirit of cooperation that was universally encountered.

Jan 1, 1921

By William H. Lesser

A recent survey of pumping plants in the anthracite region of Pennsyl¬vania showed that more than 90 percent of the pumps in use are the horizontal centrifugal types (1).2/ This report on the design and operation of centrifugal pumps should be helpful to engineers of the region who must select pumps that are best suited to particular pumping conditions in anthracite mines. Before a centrifugal mine pumping plant is designed, the special features of the pumps that may be used should be considered, especially when low repair costs and continuous operation during flood periods are prerequisites, and when acid mine water is to be pumped. Two important advantages of a centrifugal pump are that the flow is continuous and that it can be throttled without developing excessive pressure or overloading its driving unit.

Jan 1, 1950

Underground coal mine tracked vehicles have been studied to determine the state of the art and how brakes might be added to the coal haulage cars. Specific areas of interest are: brake sys terns, couplers, car trucks and car handling procedures. Problems related to adding brakes to the haulage cars appear to be: the limited amount of room to mount the brakes on the cars, brake line connection between rotary dump cars, achieving desirable braking characteristics without over complicating the system and keeping the installation cost to a reasonable figure. This document combines the information contained in the first issue of the "State-of -the-Art of Underground Coal Mine Tracked Vehicle Brake Systems," BRL Report No. 6080, with that contained in a subsequent monthly report.

Jan 1, 1973

By Gustav Wafe

"INTRODUCTION The discovery in 1901 of ""gusher"" oil production at Spindletop, Tex., Tex., a salt-dome structure, led to exploratory drilling on other known domes and known domes and in areas contiguous to salt domes in the Gulf Coast region of Texas and Louisiana. Early drilling on the flanks of the domal structures disclosed incompetent 3/ shales, which flowed into the hole when attempts were made to drill through them. Often these shales seized the drill pipes and presented with equipment then in use, an insuperable barrier to deeper drilling. The obstructing incompetent shales came to be called ""heaving"" shales by drillers who attempted to drill through them. Formations of this type have hampered the penetration of the drill bit in many area in the Gulf Coast region to such an extent that the drilling of wells through heaving shale has become a major problem."

Mar 1, 1942

By H. W. GILLETr, E. L. Mack

The production of small heats of alloy steels on an experimental scale is often desirable in beginning the study of new alloy steels before large amounts of expensive alloys are used in heats of commercial size. Such small heats can sometimes be made up at crucible-steel plants, but few crucible-steel makers care to undertake experimental heats for other firms. Small electric furnaces offer some advantages over crucible furnaces for experimental work. Hansen1 in 1909 described a small 100-kilowatt single-phase, direct- arc furnace with a capacity of 50 to 300 pounds of steel, and such furnaces, of 200 pounds capacity or larger, are being successfully used by various firms for experimental work. They have the advan- tage of using the same metallurgical procedure as is used in prac- tice for larger electric furnaces. The very small sizes have the draw- back of lack of precision in controlling the carbon content of the steel. Small Rennerfelt two-phase, indirect-arc furnaces of 40 to 60 kilo- watts and small Industrial Electric Furnace Co. furnaces, single- phase with one electrode embedded in the hearth, of 25 to 50 kilo- watts, are also in use by a few firms for experimental work or for production on a very small scale. Hoskins carbon-plate resistor crucible furnaces are also sometimes used. Little seems to have been published on the use of these furnaces in making experimental alloy steels. Keeney' has given data on the making of uranium steels in a tilting Siemens furnace of 25 pounds capacity, and has described a small stationary Siemens furnace.

Jan 1, 1922

By J. A. Lamonica

The Bureau of Mines conducted an environmental noise survey to determine the noise levels to which underground coal mine employees are exposed, to evaluate noise survey techniques and equipment, and to compare noise exposures using two criteria, Walsh-Healey and CHABA, for determining allowable exposures that were under consideration for the Federal Coal Mine Health and Safety Act of 1969- Time study techniques and Bureau-approved standard sound level meters were employed. The shift exposures of 20 percent of the miners studied were in excess of the safe standards established by both criteria. The shift exposures calculated using the Walsh-Healey criteria were greater than those calculated using the CHABA criteria owing to the intermittent nature of the exposure. Ultimately the CHABA criteria were rejected, and the Walsh-Healey criteria were adopted.

Jan 1, 1971

By Kenneth O. Bayard, John D. Sullivan

"This repot continues the series of papers being prepared at the Southwest Experiment Station of the Bureau of Mines in cooperation with the department of mining and metallurgy, University of Arizona, on factors involved in the leaching of ores. A list of previous publications is given in the bibliography at the end of this paper.Four factors are essential to the leaching of any copper-bearing ore: (1) A solution that will attack the copper minerals must get into the body of the ore particles; (2) the copper minerals must be dissolved by the solution; (3) the solution containing the dissolved copper must find its way out of the voids of the rocks into the main solution; and (4) the copper in solution must be recovered by some means of precipitation.This paper considers the third step -- the extraction of the water-soluble copper. From leached ores. The usual commercial practice in leaching copper ores consists of: (1) Crushing the ore to pass through a screen with approximately one-quarter or one-third inch openings; (2) charging the crushed ore into a fat; (3) adding, usually by upward percolation, a solution that will attack the copper minerals; and (4) washing the copper-laden solutions out of the ore with solutions weaker in copper than the pregnant solution, and finally with water. A countercurrent system of leaching and washing is usually employed. In some plants the solutions are circulated during leaching and washing, and in others they are not. In some plants the wash solutions are added by upward percolation, while at Chuquicamata the so-called ""piston-displacement"" method of washing is employed.The following condensed resume of the leaching cycle of the plant of the Inspiration Consolidated Copper Co. is given to present to the reader a picture of the steps involved in a typical leaching cycle. This plant was recently described in detail.4 The ore, crushed to pass openings 11/2 inches in diameter, passes over a screen with ¼-inch openings. The undersize from the screen goes to a Dorr howl classifier that removes the primary slime from the circuit. The overflow from the classifier is treated in a slime-leaching plant. The oversize of the ¼-inch screen passes through rolls, where it is crushed to pass a 3/8-inchscreen. The undersize from the 3/8-inch screen join with the coarse material from the classifier, and the combined products become the feed to the leaching vats. There are 13 concrete lead-lined leaching vats. The complete leaching cycle is 13 days. Eight tanks are under acid-iron content at all times; three are being washed, one tank is being filled, and the one is being excavated. The electrolyzed solution from the tank house, to which amount of new acid has been added, is put on the oldest tank of ore under need This solution travels from tank to tank and finally emerges from the newest ore"

Apr 1, 1931

This Bureau of Mines publication contains five papers pertaining to the effective grounding of mine power systems, as follows: Ground-check monitor types and safety characteristics; ground wire monitors for surface coal mines; ground bed design and measurement; electrical ground rod corrosion; and a continuous ground bed resistance monitor.

Jan 1, 1979

By James J. Olson

This report summarizes the results of a review of foreign coal mining literature conducted under the Bureau's Advancing Coal Mining Technology program. In addition to a discussion on the historical development of mechanized longwall systems, and the current state-of-the-art method in Europe, this report summarizes the previous and ongoing Bureau efforts to adapt longwall technology to U.S. conditions. The bibliographic section of this report, divided into major categories such as mine design, face management, roadway development, strata control, powered roof supports, coal winning, conveying, and automation, contains over a thousand individual entries. The purpose of this report is to provide U.S. mining engineers with background information on longwall methodology and equipment developed in foreign countries (principally Europe). The Bureau of Mines, as part of its Advancing Coal Mining Technology program, is funding R&D projects to demonstrate that the longwall mining method, successfully used in the deep mines of Europe, can boost productivity and improve safety in certain U.S. mines.

Jan 1, 1977

By Valois R. Shea-Albin

An accurate assessment of the vertical stress on a coal seam at depth is important for mine design. Vertical stress calculation techniques presently available either are not sufficiently accurate or cannot handle complex surface topography. Therefore, the U.S. Bureau of Mines developed a computerized method to calculate vertical stress exerted on surfaces at depth that includes the effect of topography. Two input data sets are required: a digital elevation model containing topographic elevations and a coal seam file defining coal seam elevations at depth. Boussinesq's equation then quantifies the vertical stress resulting from topography. The computerized method was tested on a coal seam overlain by a complex topography where a vertical stress map encompassing several square miles was produced. Results show that depth mitigates the affects of surface topography, while the coal seam topography has a direct effect on the vertical stress. In comparison to the computerized method, the direct stress method overestimates stress under hills and underestimates stress under valleys. The largest difference between the two methods occurs under the steepest topographic relief. A limitation of the computerized method is that stresses cannot be accurately determined near an outcrop.

Jan 1, 2010

By T. A. Sullivan

The work described in this report was undertaken to evaluate and develop techniques for determining the oxygen content of titanium and titanium alloys. Early investigations of volatilization techniques involving halogenation were unsuccessful. Later efforts were concentrated on evaluating vacuum fusion and inert-gas fusion techniques. Two vacuum fusion methods and an inert-gas fusion method were found to be satisfactory in the 0.02 to 1.00 pct., oxygen range. These methods are described in detail. The coefficient of variation by any of the three methods is approximately 5 pct, While the main portion of this paper is devoted to the vacuum and inert-gas fusion methods, a resume of other suggested methods for analyzing titanium for oxygen also is given. INTRODUCTION The Federal Bureau of Nines has conducted research on titanium metal since 1938. This research included development of the Kroll process for the production of titanium (2)4, various sodium reduction processes for making titanium metal and lower valent titanium chloride-sodium chloride mixtures (17), and a fused salt electrolytic process for Me production of high-purity titanium metal and the recovery of titanium by electrorefining from off-grade materials (20).

Jan 1, 1961

By B. J. Moore

This Bureau of Mines publication reviews U.S. helium resources as of January 1, 1973. These resources, estimated to be 693.7 billion cubic feet, are broken down into four classifications, as follows: helium in storage, 34.9 billion cubic feet; helium in measured helium-rich natural gas reserves, 119.5 billion cubic feet; helium in measured helium-lean natural gas reserves, 62.8 billion cubic feet; and helium in indicated or undiscovered natural gas resources, 476.5 billion cubic feet. The helium in undiscovered natural gas is considered a national resource; however, this gas may not be discovered depending on many factors beyond the scope of this paper, and most of the helium in natural gas will be dissipated as the gas is consumed for fuel and other purposes.

Jan 1, 1976

By J. H. East

"INTRODUCTION Diesel locomotives have been used successfully in underground mines of Europe for 18 years, and much has been written on the technical details of the design of these machines and the safeguards provided by the manufacturers. The actual conditions under which' the Diesel locomotives are used have not been publicized as well and consequently are not well-known. In 1945 the writer observed numerous Diesel locomotives working underground in coal and metal mines of several European countries and was favorably impressed with the practical approach to the safe use of this- type of equipment.Recent statistics showing the number of Diesel locomotives in use are not available now because of the World War, but the extent to which this type of mine locomotive was used immediately before the war is indicated by table 1, which classifies the number of locomotives used in several countries according to the type of power, such as compressed air, Diesel, and electric.Mining conditions observed by the writer in the European countries are very different from those in most coal-mining districts of the United States. The surface plants are larger and are permanently constructed of brick or concrete; numerous coal beds are worked through one shaft; the crosscut rock tunnels or levels, driven to intersect the coal beds, are lined with brick or concrete blocks where needed instead of timber; the coal beds dip more steeply and are not as thick as in most fields of the United States."

Sep 1, 1946

By Edmund Shaw

This paper is one of a series being prepared by the United states Bureau of Mines describing mining and milling methods and costs at industrial mineral plants throughout the United states. These papers are designed to disseminate technical information regarding the methods and equipment used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might, in many instances, cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention' of the reader? is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. P. J. Weisel, Inc., with office at La Habra and plant at Corona, Calif., is the only local company that produces sand for the Los Angeles glass factories, although silica sand for other purposes is produced in other parts of southern California and the adjacent portions of Nevada. The deposit at Corona consists of coarse sand imbedded in a whitish clay and differs greatly from the other deposits, which are fine-grained sandstone that must be crushed before it can be screened and washed. The preparation of Corona sand has to be thorough and includes grinding in tube mills, repeated washing and rinsing, removal of dust by air separation, and magnetic separation of iron and other minerals. This requires a plant with a complicated flow sheet. The first plant built did not make a. satisfactory glass sand, and many additions and changes were necessary. It is thought that the present flow sheet will remain substantially unchanged until a new plant is built. The design of a new plant would be simpler, but the process would be the same.

Jan 1, 1937

By Louis C. Srichta

The rapid depletion of known high-grade ore deposits of the Tri-State district and the recognized need for development of additional reserves, together with increased interest in open-pit mining of low-grade zinc-lead ores led to Bureau of Mines examination of several abandoned mining areas for possible deposits adapted to strip mining. Examination of the North Empire tract in Cherokee County, suggested that mineralized zones contiguous to previously mined 2e deposits presented probabilities of meeting the requirements for an open-pit mine - hence the tract was selected for further investigation by churn drilling. The zinc-lead deposit on the property is in a sink-hole structure that has been subjected to intense deformation and silicification. Numerous shafts, mine dumps, and surface caves are evidences of exploitation of an extensive area. The reported active mining period was 1895 to 1905. No production records are available, but it is generally stated locally that the value of the mill products exceeded $2,000,000 which represents considerable production, considering the low metal prices of that epoch.

Jan 1, 1950

By Scott W. Hazen

In recent years many mining companies have recognized that their chance for continued economic survival depends on the adaptation of technological advances in their operations. Increased productivity through new developments in mining methods and improvements in equipment has made mining and processing of lower grade ores possible. Cost analysis has produced accurate data on the costs for development, production, and processing of ore. All of these changes and cost studies have shown the necessity for increased accuracy in determining the grade of ore. Methods of estimating grade in a mineral deposit have not kept pace with the technological advances in the other areas. The same methods are in use today as in the past. Experience and judgment are major criteria of accuracy and the results are highly subjective. In 1953, as part of its research program to develop a better understanding of fundamentals of mining technology, the Federal Bureau of Mines began a sampling method research project at its Denver Mining Research Center. The basic objective of the project is to investigate sampling methods and to study the adaptation of the techniques of statistical analysis to mine sampling.

Jan 1, 1961

By G. L. Oldright, J. D. Sullivan, W. E. Keck

"An apparatus and procedure developed in the laboratory of the South-west Experiment Station of the Bureau of Mines are capable not only of determining the rate and volume of penetration of solutions into porous materials but also of determining the total volume of voids within particles of porous material, and the density. The method is applicable to ores, bricks, concretes, tiles, filter bottoms, or other porous materials of this nature. As will be made clear in the descriptive matter to follow, the method measures (a) the volume of voids within the porous materials and is not concerned with the interstitial space between the particles.Porous materials usually contain some large voids and also pores that are capillary in nature. To measure the total volume of voids in a sample it is necessary to replace the gas or gases within the voids with some liquid of known density. The large cavities can be filled quite readily, but under ordinary conditions a long time may be required to fill capillary pores. As many porous materials are of a decomposable nature it is necessary to evacuate the porous materials and then submerge them in a liquid of known density to bring about saturation in a short time. Then by the use of a hydrostatic balance the volume of porous material (solid itself) can be determined. To determine the volume of porous material plus voids it is necessary to coat the sample with some material, such s paraffin, which will prevent solution from entering the voids; then, by means of a hydrostatic balance, the volume of porous material plus voids is determined and by subtracting that of the porous material from this the volume of voids is ascertained. The rate of penetration of solutions can be determined either (a) by measuring the change in weight as the sample becomes saturated when immersed ni a liquid of know density, or (b) by measuring the volume of liquid penetrating with a dilatometer. In either instance, due to the fact that some penetration takes place as soon as the sample comes in contact with solution and before a reading can be taken, the sample must be paraffined to determine the total volume of penetration. Since many porous materials partly decompose and disintegrate in liquids the rate and volume of penetration can better be measured by dilatometer than by the change in weight, as saturation takes place when immersed in a liquid. The details of procedure for determining (a) total volume of voids, and (b) rate and volume of penetration are given in this paper."

Oct 1, 1930

By E. P. Youngman

From a scientific point of view , the zircon is by far the most remarkable of the gem stones , and a satisfactory solution of the problems offered by its characters and constitution has not yet been made . 3 Three distinct forms have been recognized , differing in specific gravity , hardness , optical properties , behavior when heated , and color.4 ( See section of this paper entitled "Description and Properties . " ) Zircon as a gem stone has not been as well known as its properties warrant . It is one of the most brilliant of the precious stones (having a high refractive index) . The colorless zircon rivals the diamond in brilliance and fire play to such an extent that a judgment based entirely upon optical inspection might be erroneous . In the opinion of gem authorities , the colored stones likewise have much merit . The blue zircon ( " Starlite" ) was so named by Kunz because of its resemblance to a " star twinkling in the night . " Another gem authority describes the leaf- green stone as one possessing a restful beauty , the red stone as having a certain ( though somber) grandeur , and the golden-yellow stone as being unsurpassed in magnificence . The slowness with which the zircon , a stone frequently mentioned in ancient literature , has come into use in modern jewelery may be owing to the fact that authorities differ as to whether the colorless and the blue zircons are found as such in nature or are treated stones . Any treated stone , although the material of which it is composed may be essentially genuine , has been considered a deception . However , according to Kunz , " Starlite is now sold over the entire world ; never has anything been so well introduced. "7 Dr. Foshag, mineral curator of the United States National Museum, states that the first allotment of zircons to enter the United States was obtained in 1921 from Siam ( through France ) for scientific or museum purposes and that four or five years later the stones were adopted by the jewelers of this country . Retail jewelers are displaying the colorless type and the blue stones , especially , in finger rings , necklaces , and like ornaments . Fine crystals have been used somewhat extensively in jewelling watches and as supports for the edges of fine balances . At one time zircons were though to be appropriate in mourning jewelery .

Jul 1, 1931