Search Documents

By William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and BethEnergy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from over-lying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine's ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the longwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 2010

By George A. Savanick

The objective of this research is to develop a method for measuring the tensile strength at the interface between minerals in rock. These measurements reflect the strength of the attractive forces operating at crystalline interfaces in rock. Since these forces act in opposition to the forces set up in various rock fragmentation processes, measuring their strength may help in designing more efficient methods of rock fragmentation. The method developed for measuring the strength of intergranular adhesion in rock involves separating a bicrystal from the rock and determining the tensile strength at its solid-solid interface. This technique has been successfully applied to the study of quartz-feldspar interfaces separated from massive pegmatites, graphic granite, and the Rockville granite, yielding average tensile strengths of 5.86, 8.62, and 10.65 meganewtons per meter squared (MN/m2) (850, 1,250, and 1,524 psi, respectively). The data this technique provides indicate that the members of these bicrystals are strongly adherent. Examirtation of bicrystals broken at the crystalline interfaces indicates that the bonds responsible for this adhesion operate over only a portion of the interfacial area. This work conclusively demonstrates that tensile strength tests can be conducted on small selected areas; for example, grain boundaries in rock. The small-scale zones of strength or weakness determined in this way can be related to the overall strength of the rock.

Jan 1, 1972

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10- to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 1993

By M. B. Cooke

 An analytical method for the determination of the gum-forming material in gasoline has been developed by the Bureau of Mines, during a study now in progress to determine the best rays for elimination of such constituents from gasoline. This method is similar in principle to that previously described by Smith and Cooke, which involved evaporation of e semple of gasoline in a small glass dish. The evaporation was started on an actively boiling steam bath and completed in an air oven at 105°C. In the improved method described below, the steam bath has been replaced by a steam heated oven in which an inert atmosphere is maintained. Air is ex- cluded from the oven, consequently the precision of the determination is increased. Furthermore, evaporating dishes different from those previously described may be used.

May 1, 1925

By G. Richards Gwinn

The mineral graphite, a form of carbon, has been known for hundreds of years, and, was first used commercially as a coloring agent. Its true identity, however, was not recognized until the end of the eighteenth century, and its commercial development did not become extensive until near the close of the ninteenth century.

Jan 1, 1943

By J. P. Schmid

Results of a comprehensive investigation of the impact of underground mine waste disposal on the health and safety of miners are presented. Information was gathered through an extensive search of American and foreign literature and personal communication with professionals in private industry and government. All conceivable health and safety hazards directly or indirectly related to underground mine waste disposal are analyzed, catagorized, and ranked on an industry-wide basis. Positive health and safety effects are analyzed and ranked in a similar way. Both potential and known hazards and positive impacts are included. Recommendations on abatement techniques for the various hazards are presented. Case histories of a fill-related accident in a metal mine and a health hazard associated wtih coal waste backfilling are included and causes and possible abatement procedures are discussed. The rule of management in the promotion of health and safety in backfilling operation is discussed.

Jan 1, 1982

By David J. Kusler

This study is an appraisal of the feasibility of recovery and the possible chemical and physical uses of the limestone from the Greenbrier Formation in western West Virginia. Data on minability, occurrence, quality, and markets were obtained from published and unpublished sources and by a limited mail survey combined with personal contacts. The estimated costs of recovery by deep mining techniques are considerably higher than competitive surface and shallow subsurface operations. Compositional in formation available for this study was limited but indicated the suitability of the limestone for most physical uses and some chemical process uses in appraisal of the uses and demand reveals that immediate markets may be difficult to establish, but for some uses long-term prospects may be encouraging, especially if the quality of limestone would be suitable for lime manufacture or use as metallurgical fluxstone.

Jan 1, 1968

By John C. Machisak

INJURY experience and employment data at all metal mines in the United States and Alaska are presented in this Information Circular for the calendar year 1958. This publication covers the metal mining industries, and contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. These operations report injury and employment information annually to the Bureau of Mines on a voluntary basis. The Bureau is authorized to make requests for such data, and the information submitted contributes immeasurably to the promotion of safety in the metal mining industry. Every effort has been made to make the annual canvass as complete as possible. This publication contains, along with production and development workers, the office employees at the mine location. The metal mines identified in this publication are classified according to the mineral ores mined; that is, copper, iron, lead-zinc, gold-silver lode, gold placer, and miscellaneous metals.

Jan 1, 1962

By M. M. Ayoub

This volume is the second of three volumes comprising the final report of the research project "Biomechanics of Low Coal." It covers only the anthropometric study of low coal miners. Volume I summarizes the overall biomechanical, anthropometry, and work physiology study conducted. Development of work clothes modified to meet the needs of low coal miners is described in Volume III. The male and female anthropometry, with the exception of weight and circumferential dimensions, was quite similar to the comparison populations. The miners tended to be heavier and have greater circumferences. The measurements made in this study were used to develop 5th, 50th and 95th percentile, quarter and half scale, male and female mannequins. These twelve mannequins can be used in work place and equipment design and redesign.

Jan 1, 1982

By E. G. Baglin

The Bureau of Mines devised a procedure for selectively extracting platinum-group metals (PGM) and gold from Stillwater Complex flotation concentrate. The Stillwater Complex is the only major U.S. PGM resource. Development of a suitable extraction technique will contribute to its exploitation. The concentrate was roasted at 1,050° C to convert host base-metal sulfides to oxides and the PGM from sulfide minerals to their elemental states. The roasted concentrate was preleached with dilute sulfuric acid to remove easily soluble gangue minerals. After pre-leaching, the concentrate was slurried with 6M HCI and leached at ambient temperature and pressure with a strong-oxidizing agent. Hydrogen peroxide, chlorine, sodium hypochlorite, nitric acid, and a persulfate salt were the oxidants investigated. The two-stage leaching scheme ex-tracted up to 97 pct of the platinum, 92 pct of the palladium, and 99 pct of the gold from the roasted concentrate. The base metals were not solubilized and reported to the residue. No attempt was made to devise a procedure to recover the copper and nickel because they comprise less than 5 pct of the value of the concentrate. Viable techniques for recovering the precious metals from the pregnant solution were sulfide precipitation, cementation with nickel, or adsorption on activated carbon.

Jan 1, 1985

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966

By Oliver C. Ralston

The Nonmetals Division studies problems relating to the use of minerals, many of which are important to national defence for purposes other than the extraction of metals. In fact, virtually all of the work of the division has been diverted to investigations pertaining to better use of the Nation's natural nonmetallic is resources as weapons of defense. The experiment stations of the division are at Norris, Tenn.; Tuscaloosa, Ala.; Seattle, Wash.; and College Park, Md. Studies involving the application of electric power to the nonmetallic minerals are conducted at the Electrotechnical Laboratory at Norris, and investigations on mineral-dressing treatment are conducted mainly at the Southern Experiment Station at Tuscaloosa. The cleaning and preparation of coal are studied at both Tuscaloosa and the Northwest Experiment Station Lit Seattle (other projects relating to utilization of coal are conducted by the Coal Division of the Bureau of Mines). Problems covering the use of minerals and fundamental problems as to their properties are studied at College Park.

Jan 1, 1941

By Oliver C. Ralston

The Nonmetals Division studies problems relating to the use of minerals, many of which are important to national defense, for purposes other than the: extraction of metals. In fact, virtually all of the work of the division has been diverted to investigations pertaining to better use of the Nation's natural nonmetallics is resources as weapons of defense. The experiment stations of the division are at Norris, Tenn.; Tuscaloosa, Ala.; Seattle, Wash.; and College Park, Md. Studies involving the application of electric power to the nonmetallic minerals are conducted at the Electrotechnical Laboratory at Norris, and investigations on mineral-dressing treatment are conducted mainly at the Southern Experiment Station at Tuscaloosa. The cleaning and preparation of coal are studied at both Tuscaloosa and the Northwest Experiment Station Lit Seattle (other projects relating to utilization of coal are conducted by the Coal Division of they Bureau of Mines). Problems covering the use of minerals and fundamental problems as to their properties are studied at College Park.

Jan 1, 1941

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future, To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

By Robert S. Warfield

The Federal Bureau of mines and U.S. Geological Survey conducted exploratory investigations and geologic mapping in the Wishbone Hill district of the Matanuska coalfield almost continuously from 1942 through 1958. These investigations delineated reserves of high-volatile bituminous coal necessary to supply the rapidly expanding military and civilian requirements in the Anchorage area. This report describes the program conducted by the Bureau of Mines from 1949 through 1958, and briefly summarizes previous investigations, the results of which have already been published. The coal-bearing structure on both the north and south limbs of the prominent Wishbone Hill syncline was explored by 8,719 feet of churn drilling and 25,460 feet of diamond-core drilling. A total of 33 holes were drilled ranging in depth from 60 to 2,114 feet. To supplement the drilling operations, bulldozer and dragline trenching were undertaken at key locations; about 25,000 cubic yards of dragline trench were excavated in the vicinity of the old Premier mine.

Jan 1, 1962

By R. A. Franks, G. F. Friel, J. C. Edwards, A. C. Smith

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system's ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system's ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system.

By E. R. Bauer

Prolonged exposure to noise can cause permanent damage to the auditory nerve and/or its sensory components, known as noise induced hearing loss (NIHL). It is the most common occupational disease in the United States today. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is addressing NIHL in the mining industry through several research efforts. This paper presents a general review of NIHL, the status of NIHL in mining, the results of the longwall noise surveys, and a review of the longwall engineering controls research efforts.

Jan 1, 2008

By Alla D. Mah

Heat content and entropy data at high temperatures were obtained for cuprous oxide (Cu2O) and cupric oxide (CuO). Experimental results and smooth values are reported. Equations are given for heat content increments and heat capacities above 2980 K. Low-temperature heat capacity data were obtained for cuprous oxide. Evaluation of the 2980 K entropy gave, S°298.15(Cu2O) = 22.08 ± 0.10 cal/deg mole. Heat of formation values were determined for cuprous and cupric oxides. The values are: AH°298.15(Cu2O) = -40,830 ± 300 cal/mole, and AH°298.15(CuO) = -37,230 ± 150 cal/mole.

Jan 1, 1967

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the CaF2-Y203 system for which solidus and liquidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. All specimen compositions were blended from high-purity materials and encapsulated in Mo or Pt20Rh prior toheat treatment. Liquidus temperatures were determined by ceramographic examination of heat-treated and quenched specimens. Solidus temperatures were determined by differential thermal analysis and by electron microprobe analysis of quenched specimens. Terminal solid solubilities were derived by parametric methods. The peritectic system was found to be pseudobinary due to the formation of yttrium oxyfluoride at temperatures near the liquidus. The peritectic point occurs at 7 mole pct Y203 and 1,438° ± 5°C. The terminal solid solubility of Y203 in CaF2 decreases from 7 mole pct at 1,438° C to 1 mole pct at 1,100° C, and the solubility of CaF2 in Y203 decreases from 9.5 to 7 mole pct over the same temperature interval.

Jan 1, 1970

By August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 2010