Search Documents

One of the major unknowns in the use of iron and copper is the quantity of various low level impurities, particularly hydrogen, that may be introduced during the deoxidizing process prior to casting. Introduction of hydrogen results in the embrittlement of components made from these metals. In addition, hydrogen bubbles in castings of copper result in the formation of blisters and swelling of the casting. During the last year, a significant effort has been made at the University of Missouri-Rolla to understand the permeation of hydrogen in galvanized automotive steel components and the hydrogen absorption during the electrodeposition of copper. The galvanized steel components consisted of automotive upholstery clips, seat belt holders and brake clips. Although the process of galvanization protects the steel from corrosion the process invariably causes the steel to pick up enough hydrogen to make it susceptible to brittle fracture.

Jan 1, 1992

By V. R. Shea-Albin

This U.S. Bureau of Mines report discusses elastic wave velocity and attenuation behavior as an indicator for changes in load and structural integrity of coal samples. Measuring changes in compressional (P)-wave and shear (S)-wave attenuation and velocity under uniaxial and triaxial compression tests revealed their effectiveness for distinguishing changes in applied load and structural failure of samples. The velocity and attenuation values were used in further calculations such as ratios of P-wave to S-wave values, dynamic elastic constants, normalized velocities, and attenuation coefficients to reveal trends for loading and failure. The behavior of both P-wave and S-wave attenuation and velocity together define distinct and consistent phases of load change and failure for uniaxial and triaxial tests. The S-wave velocity and attenuation illustrate changing axial load and initial development of microfractures within the sample preceding structural failure more clearly than those of the P-wave. The attenuation and velocity ratios and dynamic elastic constants (except the bulk modulus) respond to closure of small preexisting fractures within the coal sample with initial loading to failure of coal samples. The attenuation coefficients and normalized velocities reveal trends similar to those shown by velocity and attenuation.

Jan 1, 2010

By R. K. Koch

The normal spectral emissivities of liquid Ti, V, Zr, Mo, and Pt were determined at the fusion temperatures in an electron-beam furnace using a water-cooled copper hearth. The normal spectral emissivities were estimated above the melting points by using adjusted two-color temperatures as approximations of the true temperatures for substitution in Wien's equation. Simultaneous brightness temperatures were determined with a micro-optical pyrometer. The true temperature ranges covered were 1,668° to 1,885° C for Ti; 1,919° to 2,013° C for V; 1,855° to 2,367° C for Zr; 2,610° to 2,751° C for Mo, and 1,772° to 1,990° C for Pt. The spectral emissivities for titanium and zirconium decreased with increasing temperature. At an effective wavelength (?) of 658 mµ the emissivity of titanium ranged from 0.51 to 0.45 and zirconium, from 0.47 to 0.41. The emissivities of vanadium (? = 658 mµ) and molybdenum (? = 657 mµ) were constant at 0.41±0.02 and 0.33±0.01, respectively. The spectral emissivity of platinum (? = 658 mµ) was constant at 0.39±0.02 up to 1,900° C; above that temperature anomalous data were obtained. A mass spectrometric study indicated that platinum was reacting with back-streaming silicon vapors from the diffusion pump when the ambient pressure was greater than 2 X 10-5 torr.

Jan 1, 1973

By Russell R. Trengrove

The Copper Canyon lead-zinc mine is in the Battle Mountain. District, Lander County, Nev. It was discovered in 1866 and mined for copper until 1935 and for copper and gold until l948, when the main production became lead-zinc ore. The rocks in the area are carboniferous (Pennsylvanian and Mississippian) sedimentaries that have been intruded by quartz monzonite of Mesozoic age. They have been intensely folded, faulted, and tilted. Lead-zinc ore occurs as sulfides disseminated along fractured zones in a conglomerate arid hornfels. Development was carried out by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, making maps and. cross sections, and exploring the deposit by diamond drilling from underground. Eighteen holes were drilled, for a total of 2,594 feet. This report contains a brief history of the property and a description of mining methods and beneficiation of the ore, geology, ore deposits and drilling done by the Bureau of Mines. It also contains detailed analyses of the ore samples taken and logs of the holes drilled.

Jan 1, 1951

By C. W. JEFFERS

During the past few years the use of mechanical equipment for the loading and transportation of coal at the working face has rapidly increased . Many mining officials are of the opinion that mechanical methods have tended to reduce the hazards of mining, and a number of statements have been made to this effect . Little actual data upon which to base conclusions in regard to the relative safety of various methods of mining have been made available . While it may be possible that these systems of mechanical mining are inherently less hazardous , obvious dangers should not be disregarded in the belief that the mere act of installing mechanical loading equipment automatically brings about better accident records . The same rules and regulations , modified to meet the new regime must be applied with the same discipline as heretofore . By diligent study and application there is reason to believe that new methods of concentrated mining can be utilized with at least a possibility of increased accident performance . With the idea of preventing accidents by taking available precautions against their occurrence , attention should be directed to the dangers that exist where room and face conveyors are in operation . Due to the cost pressure prevalent in the mining industry at the present time mechanical means are often used in an attempt to decrease cost of production. The management , after having spent considerable sums of money for new equipment , is expected by stockholders and investors to show results by increasing tonnage and reducing operating costs . Consequently the operating officials apply the same pressure to local mine officials to obtain results . The natural reaction of the superintendent and mine foreman is to secure the maximum production from the new method , and unfortunately safety is frequently , if not generally , sacrificed to this end . In many instances , operators of new types of mechanical loaders are difficult to secure and after being obtained are difficult to hold , especially if the new equipment is more or less in the experimental stage . The tendency is to handle the machine operators with " gloved hands " and to permit many unsafe practices which ordinarily would not be allowed, in order to keep from antagonizing them and losing their services . Although these unsafe practices become habitual and even uneconomical , conditions thus established are difficult , sometimes impossible , to change .

Jul 1, 1930

By Dennis R. Dolinar, Eric R. Bauer

Skin failures of roof and rib in underground coal mines continue to be a significant safety hazard for mineworkers. Skin failures do not usually involve failure of the support systems, but result from rock or coal spalling from between the support elements. For instance, in 1997 more than 800 miners were injured by roof and rib falls, of which 98% were the result of skin failures [Bauer et al. 1999]. Also, nearly 80% of the roof and rib failure injuries occurred at or near the working faces in development sections. The face area is a zone where the potential for skin failure accidents and injuries and for roof and rib failures is high because of mining activity, ground readjustment due to changing stress conditions, and the higher exposure of mine workers. In addition, failures occur where the roof and rib are unsupported. This paper reviews the roof and rib accident statistics resulting from skin failure, and highlights the incidences by type, numbers and percentage, in-mine location, supported and unsupported roof, and worker activity at the time of injury. Also discussed are the causes of roof and rib skin failures, current and improved support methods and materials for skin surface control, and machine design modifications for improved roof bolter operator protection. It also reviews the historical literature on skin failures and control methods.

Jan 10, 2000

By Graham W. Marks, Betsy M. Jones

"Recently4/ it was shown that the total energy method5/ of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing this work, the present report deals with analyses for beryllium, zinc, cadmium, and indium.There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved.As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is associated with zinc and cadmium in zinc ores.The authors wish to acknowledge the valuable assistance of the staff of the Bureau of Mines Analytical Laboratory who made the chemical analyses and supplied the ore samples used in this work.A brief description of the procedures followed in making the standard curves and analyses is given below; a detailed discussion will be found in an earlier paper.6/Basically, the procedure for determining a standard curve consists of two parts: (1) Choosing a suitable line in the spectrum of the element to be determined and (2) determining the variation in the intensity of this line with the amount of the element burned in the arc."

Nov 1, 1948

By C. M. Frost

Crude shale oil produced during in situ retorting by the Bureau of Mines at Rock Springs, Wyo., was refined by three schemes. In the first, the crude oil was fractionated to raw naphtha and 400° F+ residuum. The residuum was hydrogenated over cobalt molybdate catalyst at 815° F and 1,100 psig. The blended raw and 160°-400° F hydrogenated naphthas were hydrodenitrified and then catalytically reformed. The 400° F+ hydrogenated oil was catalytically cracked. In the second scheme, the crude was hydrogenated over nickel-tungsten catalyst at 800° F and 1,500 psig. The hydrogenated fractions were processed by methods used in the first scheme. The third scheme resembled the second but, prior to hydrogenation, the crude was "hydrostabilized" over cobalt molybdate at 500° F and 500 psig. Yields of reformate and cat-cracked gasoline as volume-percents of the crude, and research-method octane numbers (with 3 ml TEL) for the three methods were as follows: First method, 32 pet reformate, 90 octane; 19.5 pct cracked gasoline, 99.2 octane. Second method, 29 pet reformate, 81.1 octane; 21.3 pct cracked gasoline, 99.6 octane. Third method, 28.2 pet reformate, 86 octane; 28.7 pct cracked gasoline, 95.9 octane.

Jan 1, 1974

By Ad. Breyre

For more than 20 years, Belgium, leading all the coal-mining countries, has made increasing use of sheathed explosives, which wore first suggested by the late E. Lemaire, predecessor of the author as Director of the Institut National des Mines. It appears to the author that it will be valuable to show how the use of sheathed explosives has developed in Belgium, hour the various difficulties encountered in their manufacture have been overcome gradually, and the tyres of sheathing that have survived and the reasons for their survival.

Jan 1, 1940

By J. H. Holden

The Federal Bureau of Mines is doing research and development work on a pressure-gasification pilot plant for producing synthesis gas directly from pulverized coal, oxygen, and steam. A pressure-gasification pilot plant has been constructed, and an investigation was made with the following basic objectives: 1. Determining the effect of varying pressure (75, 100, 150, and 300 p.s.i.g.), coal rate (400, 700, and 1,000 pounds per hour), and oxygen-to-coal ratio (8 to 11 std, c,f. per pound), on percentage of carbon gasified, oxygen and coal requirements per unit of CO + H2 produced, exit-gas temperature, and heat loss. The steam-to-coal ratio was maintained at approximately 0.3 pound per pound. 2. Development of a stabilized gasification zone or reaction space. 3. Improvement in operability of the pilot plant.

Jan 1, 1960

By Rodney D. Rosenkranz

Energy consumption in domes tic copper production has increased nearly 60 percent in the last 10 years, reaching approximately 175 trillion Btu in 1973. Energy required to produce 1 pound of copper rose from nearly 41,000 Btu in 1963 to nearly 50,000 Btu in 1973. Production from lower grade ores and strict pollution control regulations have contributed to this increase. Each stage of copper production has been analyzed to determine total energy consumed, energy mix required, cost of the energy, and recent or proposed changes in operations which may affect the consumption of energy by the copper industry. Data have been gathered from a recent Bureau of Mines canvass of the industry, from visits to copper operations, and from conversations with copper industry officials.

Jan 1, 1976

By J. D. Marchant

Solid-state electrotransport of impurities in cerium, lanthanum, and praseodymium, using a pulsed current, was investigated. The results were compared with those of using a steady current. Impurities that showed appreciable movement with the pulsed current, but not with the steady current, were as follows: Molybdenum and oxygen in cerium, aluminum, iron, and molybdenum in lanthanum. The use of a pulsed current enhances the practical application of solid-state electrotransport to remove a wider variety of impurities from the host metals.

Jan 1, 1971

By J. T. McCartney

OPTICAL PROPERTIES of U.S. coals of differing rank have been investigated by the Bureau of Mines, for about 20 years. These investigations have been remade to further the development of an objective basis for petrographic analysis of coal and to add to knowledge of the structure and composition of coal and coal components by determining their optical constants in various regions of the electromagnetic spectrum. Various experimental techniques have been used in these studies, including determination of reflectance from bulk specimens and transmittance of thin and ultrathin sections, interferometry, electron microscopy, and election diffraction. Similar studies leave also been made of graphite, the end product of coal metamorphism. The bureau of Mines conducted the first U.S. investigation of reflectance properties of coal components, laying the foundation for petrographic analysis based on arbitrary reflectance classes and for automated reflectance analysis of coals. Optical constants of coals of differing rank and of graphite have been determined in the ultraviolet-visible-near infrared spectrum. Maxima in the optical constants of graphite were observed in the ultraviolet region and were interpreted to be related to transitions of electrons between the valence and conduction bands. Similar maxima for coals, especially high-rank coals, appeared to be characteristic of the presence of graphitelike layers. A special application of optical theory to absorbing, anisotropic materials like graphite and high-rank coals has been developed. Electron microscopic and electron diffraction studies of coals have revealed various ultrafine structures in coal components and have shown the evolution of an oriented, crystalline graphite structure in high-rank coals.

Jan 1, 1967

By J. J. Taber

This is the final report on Grant No. G0144067. The report presents the results of a number of laboratory studies carried cut in several different ways to determine the effectiveness of foam for blocking the flow of gas in coal. The effectiveness; (of foam for retarding or blocking the flow gas in various porous media has been observed by many investigators1-4 but we are not aware of similar detailed studies in coal. Because of the diversity of our experiments, the key findings and general conclusions are presented very briefly in Section II. As a convenience to the reader a complete table of cements is included to enable the reader to find those experiments and studies of greatest interest.

Jan 1, 1976

By W. K. Tolley

This report presents data collected during research by the Bureau of Mines on corrosion of grinding media. Corrosion rates of eight alloys commonly used in grinding media were tested in synthetic mill water using an ultrasonic grinding device especially designed for this work. Electro-chemical measurements showed variations in corrosion rates for these alloys between 9.8 mpy for medium-carbon steels and 0.14 mpy for high chromium white irons. Bureau data are discussed along with data from the literature to indicate that corrosion causes less than 10 pct of the wear of grinding media in commercial grinding mills. A comparison of corrosion rates for various types of grinding media shows that alloying elements and electrochemically active inclusions in steel affect the corrosion behavior of the media.

Jan 1, 1984

By Welby Courtney

Because of the inherent safety problem associated with the deposition of airborne respirable dust onto the floor and other airway surfaces, the Bureau of Mines investigated the rate of reduction of airborne respirable dust in an airway due to deposition of the particles onto the surfaces of the airway. The effects of relative humidity and air velocity on the deposition rate were examined. It was found that the deposition rate was comparable in magnitude with the Stokes sedimentation rate and that it was independent of relative humidity. However, near the dust source the deposition rate depended significantly upon the air velocity, with such dependence decreasing with increasing distance from the dust source. In addition, the size distribution of the airborne particles was approximately constant along the first 300 ft of the airway, indicating that it was not merely the larger (heavier) particles that were being deposited. These results suggest that deposition, though comparable with the Stokes sedimentation rate in magnitude, does not follow a simple Stokes-type process, and that the process of deposition remains to be explained.

Jan 1, 1986

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By James R. Coldwell

Mining and processing cost analyses were conducted by the U.S. Bureau of Mines on massive sulfide copper-zinc and low sulfide vein gold deposit types that may be found in the Ketchikan Mining District. Reserves and recoverable metal values (RMV) needed to make these deposits economically viable were modeled. Methods for estimating ore grades and required RMV are presented. Economic modeling for massive sulfide deposits indicated the RMV necessary for a 15% Discounted Cash-Flow Rate-Of-Return (DCFROR) for an underground cut-and-fill mine ranged from $137/mt for a 6,100 mtpd on-site milling operation to $526/mt for a 450 mtpd off-site milling operation. On-site milling was always less costly than off-site milling. Economic modeling for low sulfide vein gold deposits indicated the RMV necessary for a 15% DCFROR for an open-pit mine, off-site mining operation ranged from $S4/mt at 2,900 mtpd to $71/mt at 360 mtpd, and from $49/mt at 2,900 mtpd to $100/mt at 360 mtpd for an on-site milling operation. Off-site milling was less costly than on-site milling until production exceeded approximately 1,700 mtpd. Then, economies of scale reduced operating costs enough to offset the higher capital costs required for on-site milling.

Jan 1, 1995

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations wi.thin a multiple-seam configuration. At two mine sites where such ground interactions were present, the Bureau performed a complete geological analysis and installed and monitored instrumentation to gather pertinent data on rock mechanics. Overburden depth varied dramatically in the vicinity of the study area and reached a maximum at the study site; innerburden thick-ness was less than a pillar width (40 to 4S ft); heaving was experienced in both mines where sandstone and/or shale floor units were observed; overlays of the mine layouts show pillars were not totally superpositioned; a maximum of S in of roof to floor convergence was measured; and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig over instrument setting pressure.

Jan 1, 1987

By W. A. Jacob, E. W. Dean

The Pittsburgh petroleum laboratory of the Bureau of lines has recently developed an improved method for the determination of water in pctroleum emulsions. It has been described in detail in an article entitled "A convenient method for the determination of water in petroloum and other organic emulsions" by E. W. Dean and D. D. Stark (Jour. Ind., and Enc. Chem. Vol. 12, ſay, 1920, page 436). It is essentially a modification of the familiar procedure of "distillation with an iniscible solvent", the improvement consisting in the use of apparatus that is rºck more convenient than any previously employed. The method has been used with marked success in the Bureau's laboratories for a period of about a year and has also been tried with equal satisfaction by a number of other laboratories. It has been most extensively employed for determining the water content of heavy fuel oils but has been applied also to several other types of emulsions, including shale oils, tars derived from coal, greases, and mixtures of powdered coal, oil and water. The Bureau has received a number of requests for information regarding commercial sources for the apparatus used, and having been assured of the value of the method, has taken steps to render it available for general use. - The equipment is, with the exception of two items, made of parts that are obtainable from the ordinary stock of chemical supply houses. The two exceptions are (1) the so-called "distilling tube receiver" and (2) the electric heater. The former is an essential part of the equipment; the latter is a convenient ac cessory but it can if necessary be roplaced by a gas burner. Efforts on the part of the Bureau staff to ronder these two items of apparatus available for purchase from supply houses, or for production by the user are hero described.

Sep 1, 1920